User Manual LASER LIGHT AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT CLASSIFIED PER EN/IEC 60825-1:2007 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
TABLE OF CONTENTS 1. Before You Begin ..................................................................................................................................................... 3 What Is Included ........................................................................................................................................................ 3 Unpacking Instructions ...............................................................................................................................
1. BEFORE YOU BEGIN What Is Included 1 x MiN™ Laser FX 2.0/RGX 2.0 1 x Flexible tripod 1 x Adjustable stand 1 x Wireless remote 1 x Power supply 1 x Clamp adaptor 1 x Warranty card 1 x User manual Unpacking Instructions Immediately upon receipt, carefully unpack this product and check the container to make sure you have received all the parts indicated above in good condition.
Safety Instructions Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this document. Always make sure that the voltage of the outlet to which you are connecting this product is within the range stated on the decal or rear panel of the product.
Non Interlocked Housing Warning This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels, accessible if the unit is opened, can cause instant blindness, skin burns, and fires. Laser Safety Notes STOP AND READ ALL THE LASER SAFETY NOTES BELOW Laser Light is different from any other light sources with which you may be familiar.
Laser Safety Label Reproduction Top Front Rear Bottom MinLasers 2.
LASER EXPOSURE Laser light - Avoid direct eye contact! Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard “For Safe Use of Lasers”, available from the Laser Institute of America: www.laserinstitute.org. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the International Laser Display Association: www.laserist.org.
2. INTRODUCTION Product Overview Mode Button Microphone Wireless Remote Receiver LED Indicator Laser Output Green Laser Dimmer 12 V Power In Cooling Fan MinLasers 2.
3. SETUP AC Power This product includes an external power supply which is auto-ranging and runs on 100~240 VAC, 50/60 Hz power. Only use the included power supply! To obtain a replacement power supply, contact Chauvet®. Power Supply To determine the power requirements for a particular product, see the label affixed to the back plate of the product or refer to the product’s specifications chart. A product’s listed current rating indicates its average current draw under normal conditions.
Floor Stand, Flexible Feet (3) Coupler Clamp MinLasers 2.
Proper Usage This product is for overhead mounting only. For safety purposes, CHAUVET® recommends mounting your lighting effect products on steady elevated platforms or sturdy overhead supports using suitable hanging clamps. In all cases, you must use safety cables. You can obtain appropriate mounting hardware from your lighting vendor. International laser safety regulations require that laser products must be operated in the fashion illustrated below, with a minimum of 3 meters (9.
4. OPERATING INSTRUCTIONS Manual Mode Access the four different operating modes available in this product by using the button on the front panel. Pressing and holding the button for 2.5 seconds will turn the product on or off. Press to cycle through the modes. Please see a description of each mode below.
5. APPENDIX General Troubleshooting SYMPTOM Breaker/Fuse keeps blowing Device does not power up POSSIBLE CAUSE(S) Excessive circuit load Short circuit along the power wires Check for a short in the electrical wiring (internal and/or external). No power Check for power on Mains. Loose power cord Wrong DMX addressing Product is not responding to DMX POSSIBLE ACTION(S) Check total load placed on the electrical circuit.
Product Maintenance Dust build up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, you should clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency. To clean this lighting product, follow the instructions below: 1. Unplug the product from power. 2.
Returns Procedure The user must send the merchandise prepaid, in the original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. The user must clearly label the package with a Return Merchandise Authorization (RMA) number.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length 4.3 in (111 mm) Width 3.3 in (85 mm) Height 1.8 in (45 mm) Weight 0.7 lbs (0.3 kg) Note: Dimensions in inches rounded to the nearest decimal digit Power Power Supply Input Voltage 12 VDC 600 ma Range 100~240 V, 50/60 Hz Voltage Selection Auto-ranging Parameter Energy consumption Operating current (units) 120 V, 60 Hz 6W 0.1A 230 V, 50 Hz 6W 0.