User Manual
TABLE OF CONTENTS 1. Before you Begin ............................................................................ 3 What is Included........................................................................................ 3 Unpacking Instructions .............................................................................. 3 Text Conventions ...................................................................................... 3 Icons ........................................................................
1. BEFORE YOU BEGIN What is Included • • • • Circus Power Cord Warranty Card User Manual Unpacking Instructions Immediately upon receiving this product, carefully unpack it and check the container in which you received it. Make sure that you have received all the parts indicated above and that they are all in good condition.
Product at a Glance Use on Dimmer Outdoor Use Sound Activated DMX Master/Slave Auto Programs Auto-ranging Power Supply Replaceable Fuse User Serviceable Duty Cycle Safety Notes Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. Page 4 of 16 • Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this document.
2. INTRODUCTION Product Overview Safety DMX In DMX Out Power Out Power In Fuse holder Control Panel (LED Display) Circus User Manual (Rev.
3. SETUP AC Power This product has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its average current draw under normal conditions.
Power Linking This fixture provides power linking via the Edison outlet located in the back of the unit. Please see the diagram below for further explanation. Power Linking Diagram 1st Fixture 2nd Fixture 3rd Fixture Other fixtures You can power link up to 26 Circus units on 120 VAC or up to 40 Circus units on 230 VAC.
Mounting Orientation The Circus may be mounted in any position, provided there is adequate room for ventilation around it. Rigging Be sure that the structure onto which you are mounting this product can support its weight. Please see the “Technical Specifications” section of this manual for weight information. Make sure to mount the fixture securely to a rigging point, whether an elevated platform or a truss.
4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display. Button
Starting Address When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. If you choose a starting address that is too high, you could restrict the access to some of the fixture’s channels. The Circus uses up to 3 DMX channels in its single DMX mode, which defines the highest configurable address to 510. If you are not familiar with the DMX protocol, you may refer to the “DMX Primer” section in the “Technical Information” chapter.
DMX Channel Assignments and Values Channel 1 2 3 Circus User Manual (Rev.
Configuration (Standalone Modes) Set this product in one of the standalone modes to control it without a DMX controller. 1) Connect this product to a suitable power outlet. 2) Turn this product on. Never connect a fixture that is operating in any standalone mode, whether Static, Automatic, or Sound to a DMX string connected to a DMX controller. This is because fixtures in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.
Auto Configure This product has 42 built in light shows (auto programs). In this mode, it will cycle through each of those programs. To enable the Auto Configure mode, follow the instructions below: 1. Plug the fixture into power. 2. Press
5. TECHNICAL INFORMATION General Maintenance Dust build up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life or mechanical wear. To maintain optimum performance and minimize wear, you should clean your lighting fixtures at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 9.1 in (231 mm) 11.8 in (300 mm) 13 in (330 mm) 8.3 lbs (3.7 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Voltage Selection Range Auto-ranging 100~240 V, 50/60 Hz Parameter 120 V, 60 Hz Consumption 27 W 230 V, 50 Hz 31 W Operating Current 0.3 A max 0.
Returns The user must send the merchandise prepaid, in the original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before shipping the fixture. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. The user must clearly label the package with a Return Merchandise Authorization (RMA) number.
