LASER LIGHT AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT CLASSIFIED PER EN/IEC 60825-1:2007 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
TABLE OF CONTENTS 1. BEFORE YOU BEGIN ................................................................................................................................ 3 WHAT IS INCLUDED ................................................................................................................................................................................ 3 UNPACKING INSTRUCTIONS ............................................................................................................................
1. BEFORE YOU BEGIN What is included 1 x Cirrus™ 1 x Power supply (100~240 VAC, 50/60 Hz, 3A) 1 x Warranty Card 1 x User Manual Unpacking Instructions Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
Safety Instructions Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.
Non Interlocked Housing Warning This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels, accessible if the unit is opened, can cause instant blindness, skin burns, and fires. Laser Safety Notes STOP AND READ ALL THE LASER SAFETY NOTES BELOW Laser Light is different from any other light sources with which you may be familiar.
Laser Safety Label Reproduction Cirrus™ User Manual 6 8/18/2011
LASER EXPOSURE Laser light - Avoid direct eye contact! Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard “For Safe Use of Lasers”, available from the Laser Institute of America: www.laserinstitute.org. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the International Laser Display Association: www.laserist.org.
2.
3. SETUP AC Power This product requires an external power supply, which is included. The included power supply is rated for an input of 100~240 VAC, 50/60 Hz, and an output of 5 V, 3 A. Power Supply Before powering on the unit, make sure the line voltage to which you are connecting it is within the range of accepted voltages. Only use the included power supply! To obtain a replacement power supply, contact Chauvet®.
Proper Usage This product is for overhead mounting only. For safety purposes, CHAUVET® recommends mounting your lighting effect products on steady elevated platforms or sturdy overhead supports using suitable hanging clamps. In all cases, you must use safety cables. You can obtain appropriate mounting hardware from your lighting vendor. International laser safety regulations require that laser products must be operated in the fashion illustrated below, with a minimum of 3 meters (9.
4. OPERATION Sound-Active This product has a sound-active mode. This means that the triggering for the built-in program will respond to the built-in microphone. Please see the instructions below for further explanation. 1. 2. 3. 4. Plug the product into power. Turn the power switch to the ON position. Turn the mode switch to the MUSIC position. Adjust the sound sensitivity pot with a suitable flat-head screw driver. The DIMMER adjustment knob controls solely the blue LED, NOT either laser.
5. APPENDIX Returns Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #). Products returned without an RMA # will be refused. Call CHAUVET® and request RMA # prior to shipping the product. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
General Troubleshooting Applies to Symptom Solution(s) Lights Foggers & Snow Controllers Dimmers & Chaser Breaker/Fuse keeps blowing Check total load placed on device Chase is too slow Check user manual for speed adjustment Device has no power Check for power on Mains. Check device’s fuse. (internal and/or external) Loss of signal Use only DMX cables Install terminator Note: Keep DMX cables separated from power cables or black lights.
Technical Specifications WEIGHT & DIMENSIONS Length............................................................................................................................. 7.4 in (188 mm) Width ............................................................................................................................ 10.3 in (261 mm) Height ................................................................................................................................ 6 in (175 mm) Weight ..............