User Manual
TABLE OF CONTENTS 1. Before You Begin ...........................................................................................................3 What Is Included ........................................................................................................................ 3 Unpacking Instructions ............................................................................................................... 3 Claims .................................................................................
1. BEFORE YOU BEGIN What Is Included Unpacking Instructions Claims Text Conventions Cubix™ 2.0 Power Cord • • • • Warranty Card Quick Reference Guide Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Product at a Glance Use on Dimmer Outdoor Use Sound Activated DMX Master/Slave Safety Notes Auto Programs Auto-ranging Power Supply Replaceable Fuse User Serviceable Duty Cycle Please read the following Safety Notes carefully before working with the product. The Notes include important safety information about installation, usage, and maintenance.
2. INTRODUCTION Product Overview LED Display Fuse Holder Safety Loop DMX In/Out Power In/Out Perimeter (Side) Lenses (20) Middle Lens Cubix™ 2.0 User Manual (Rev.
Product Dimensions Page 6 of 13 Cubix™ 2.0 User Manual (Rev.
3. SETUP AC Power The Cubix™ 2.0 has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Cubix™ 2.0 may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes. • Make sure that the structure onto which you are mounting the product can support the product’s weight.
4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel.
DMX Channel Assignments and Values 7-CH Channel 1 Function Colors Value 000 005 029 057 085 113 141 169 198 004 028 056 084 112 140 168 197 224 Setting No function Red Green Blue Cyan Purple Yellow White 3-Color switching Side Lenses 225 255 7-Color switching 2 Strobe 3 Motor Rotation 4 Auto Programs 5 Auto Program Speed 6 Strobe 7 Auto Programs (All Lenses) 000 004 No function 005 255 0~30 Hz 000 127 Rotation with indexing Back and forth with increasing 128
Master/Slave Mode The Master/Slave mode allows a single Cubix™ 2.0 unit (the “master”) to control the actions of one or more Cubix™ 2.0 units (the “slaves”) without the need of a DMX controller. The master unit will be set to operate in either Automatic or Sound Active mode, while the slave units will be set to operate in Slave Mode. Once set and connected, the slave units will operate in unison with the master unit. Configure the units as indicated below. Slave units: 1.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 10.5 in (267 mm) 12 in (305 mm) 11.6 in (296 mm) 8.1 lbs (3.7 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Light Source Photo Optic Thermal DMX Ordering Page 12 of 13 Power Supply Type Range Voltage Selection Switching (internal) 100~240 V, 50/60 Hz Auto-ranging Parameter 120 V, 60 Hz 230 V, 50 Hz Consumption 50 W 48 W Operating 0.4 A 0.
To return a product or request support: • • • In the U.S., contact CHAUVET® World Headquarters (see below). In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below). In any other country, DO NOT contact CHAUVET®. Instead, contact your lighting distributor. See www.chauvetlighting.com for distributors outside the U.S., UK, or Ireland. Outside the U.S., UK, or Ireland, contact your distributor and follow their instructions on how to return CHAUVET® products to them.
