User Manual
Edition Notes Trademarks Copyright Notice The WELL™ 2.0 (Wireless Event LED Luminaire) User Manual Rev. 01 covers the description, safety precautions, installation, programming, operation, and maintenance of the WELL™ 2.0 product. CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or Chauvet).
Table of Contents 1. Before You Begin ............................................................................................... 1 What is Included.................................................................................................................. 1 Unpacking Instructions ........................................................................................................ 1 Text Conventions ................................................................................................
Reset ......................................................................................................................................... 16 TOUR Notes...................................................................................................................... 16 Master Dimmer .......................................................................................................................... 16 Red, Green, and Blue Color Selection........................................................
1. Before You Begin What is Included Single Unit: Six-piece Set: • One WELL™ 2.0 fixture • Six WELL™ 2.0 fixtures • One Battery Charger • One six-bay flight case with built-in battery charger • Warranty Card • Warranty Card • Quick Reference Guide Unpacking Instructions Text Conventions • Quick Reference Guide Immediately upon receiving this product, carefully unpack it and check the container in which you received it.
Safety Notes Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. It is important to read all these notes before starting to work with this product. There are no user serviceable parts inside this product. Any reference to servicing it you may find from now on in this User Manual will only apply to properly CHAUVET® certified technicians.
2. Introduction Product Description Features WELL™ 2.0 User Manual Rev. 01 The WELL™ 2.0 (Wireless Event Light Luminaire) is a battery powered, portable upward wash light. It consists of a single unit that contains the 12 V gel battery, the LEDs, the LED drivers, and the main control. The battery provides up to 12 hours of runtime. When purchased as a single unit, it comes with a stand-alone single unit battery charger. Additional batteries are available for purchase.
DMX Channel Summary Page 4 of 28 Tour DMX Channel 1 2 3 4 5 6 7 8 9 10 11 12 Function Master Dimmer Module 1 Red Module 1 Green Module 1 Blue Module 2 Red Module 2 Green Module 2 Blue Color Macro + White Balance Strobe Auto + Custom Programs Auto Speed Dimmer Speed ARC.1 DMX Channel 1 2 3 Function Red Green Blue AR1.D DMX Channel 1 2 3 4 Function Master Dimmer Red Green Blue AR1.
Product Overview Front View W DMX Antenna LED Panels Power Indicator On/Off Switch Handle LED Panel Adjust DMX In/Out Bottom View Battery Connector Storage Battery Switch Retractable Foot Foot Release Control Panel WELL™ 2.0 User Manual Rev.
Product Dimensions Page 6 of 28 WELL™ 2.0 User Manual Rev.
3. Setup AC Power The WELL’s battery charger, whether stand-alone or inside the flight case, has an autoranging power supply that can work with an input voltage range of 100~240 VAC, 50/60 Hz. Make sure that you are connecting this product to the proper voltage, as per the specifications in this guide, the product’s user manual, or on the product’s sticker. Always connect this product’s battery charger to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire.
Master/Slave Connectivity The Master/Slave mode allows a WELL™ 2.0 unit to control or more WELL™ 2.0 units without a DMX controller. See the Master/Slave section of the Operation chapter for programming information. The master links to the slave fixtures using the standard DMX serial connection. If you are not familiar with the Master/Slave connectivity, you may download the “DMX Primer” document from the CHAUVET® Web site. Note: This function is not available under wireless operation.
4. Operation Operation Notes • Always operate the unit in an upright position. • Never tilt the unit more than 10º. • Only use the retractable foot to tilt the unit. • Do not operate the unit in a sealed enclosure or in an area without air circulation. Turning Unit On • Turn the battery storage switch on. • Push the On/Off switch on the top for more than three seconds (the built-in red LED will illuminate solid).
Battery Charge Notes • Make sure to turn the battery storage switch on before connecting the unit to the charger. • Always use the supplied charger to recharge the built-in battery. • Recharge the battery within three days of last use. • Recharge the battery to full capacity before storing this product. • For best results, charge the battery in a temperature between 32º F (0º C) and 95º F (35º C). • When charging the battery, keep the unit at no less than 1 m from any open flame or hot plate.
Wireless Operation The WELL™ 2.0 can operate in W-DMX mode up to 300 m (900 feet) from the W-DMX transmitter. The W-DMX receiver in the WELL unit must be paired with the W-DMX transmitter for wireless operation. Initial Setup 1) 2) 3) 4) 5) Configuration 1) 2) 3) 4) Fixture Pairing Turn the W-DMX transmitter on. Connect the W-DMX transmitter to a DMX controller. Place the WELL™ 2.0 unit within 300 m from the W-DMX transmitter. Disconnect any DMX cable from the WELL™ 2.0 unit.
Control Panel Description Control Options Button Function
Continued from previous page Static Color Auto Programs The Static Color mode allows for permanent RGB color mixing without a DMX controller. 1) Go to STAT. 2) Select the desired color (RED, GREN, or BLUE). 3) Select the desired color value (0~255). 4) Repeat for the other colors. 5) Select STRB. 6) Select the desired frequency (0~20). Auto programs allow for dynamic RGB color mixing without a DMX controller. 1) Go to AUTO. 2) Select the desired auto (AT.01~10) or custom program (PR.01~10).
Continued from previous page Color Setting The COLOR setting determines how the WELL generates the white color based on various RGB settings. 1) Go to SET. 2) Select COLO. 3) Select OFF, RGBW, or UC. OFF: When the RGB faders are all set to “255”, the output is maximum, although the resulting white color may not be balanced. RGBW: When the RGB faders are all set to “255”, the resulting output is defined by the configured White color (see RGB to White Adjustment).
Continued from previous page RGB to White Adjustment This setting allows the user to select and edit the temperature of the white color shown when RGB to White (RGBW) is active in SET > COLO (see Color Setting). 1) Go to CAL2 and 2) Press when you see RGB.W on the display. 3) Select a color (RED, GREN, or BLUE). 4) Select a color value (0~255). 5) Repeat for the other colors. The values of RED, GREEN, and BLUE configured from RGB.
Continued from previous page Reset Default Values This setting allows the user to reset the WELL fixture to its default values, including deleting the custom programs. 1) Go to SET. 2) Select REST. 3) When prompted, enter the master access password as shown in Control Panel Lock. 4) Wait for the reset process to finish.
Menu Map WELL™ 2.0 User Manual Rev.
DMX Values TOUR Page 18 of 28 Channel Function 1 2 3 4 5 6 7 Master Dimmer Module 1 Red Module 1 Green Module 1 Blue Module 2 Red Module 2 Green Module 2 Blue 8 Color Macro + White Balance 9 Strobe 10 Auto + Custom Programs 11 Auto Speed 12 Dimmer Speed Value 000 ó 255 000 ó 255 000 ó 255 000 ó 255 000 ó 255 000 ó 255 000 ó 255 000 ó 010 011 ó 030 031 ó 050 051 ó 070 071 ó 090 091 ó 110 111 ó 130 131 ó 150 151 ó 170 171 ó 200 201 ó 205 206 ó 210 211 ó 215 216 ó 220 221 ó 225 226 ó 230 231 ó
ARC.1 Channel 1 2 3 AR1.D Channel 1 2 3 4 AR1.S HSV Channel Function 5 Strobe 2 3 Channel 1 2 3 4 5 6 WELL™ 2.0 User Manual Rev.
5. Technical Information Fixture Maintenance To maintain optimum performance and minimize wear, the user should clean this product frequently. Usage and environment are contributing factors in determining the cleaning frequency. As a rule, the user should clean this product at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear.
Troubleshooting Guide Symptom Low output One or more LEDs on a panel do not illuminate No LED illuminates Control panel operates normally Circuit breaker/fuse keeps tripping/blowing Fixture does not power up Battery does not charge Fixture does not respond to wired DMX or responds erratically Cause(s) Depleted battery Incorrect COLOR settings Dirty LED lens cover LED panels in wrong angle Faulty LED(s) No power to the LEDs Faulty main control board No power to the LEDs Faulty main control board Faulty
Returns Procedure The user must send the merchandise prepaid, in the original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before shipping the fixture. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. The user must clearly label the package with a Return Merchandise Authorization (RMA) number.
Technical Specifications Dimensions and Weight Length Width Height Weight 7.0 in (200 mm) 7.5 in (190 mm) 13.8 in (350 mm) 36.3 lbs (16.5 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Electrical Light Source Photo Optic Thermal DMX WDMX Ordering Options WELL™ 2.0 User Manual Rev.
CHAUVET® 5200 NW 108th Avenue Sunrise, FL 33351 (USA) (800) 762-1084 – (954) 577-4455 FAX (954) 929-5560 www.chauvetlighting.com WELL™ 2.0 User Manual Rev.