User Manual
Edition Notes Edition Notes This User Manual covers the description, safety precautions, installation, programming, operation, and maintenance of the Nexus™ 4x4. CHAUVET® released this edition of the Nexus™ 4x4 User Manual in October 2013. Trademarks CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or Chauvet).
Before You Begin Table of Contents 1. Before You Begin ........................................................................................................................................................... 2 What Is Included ............................................................................................................................................................................. 2 Claims ..................................................................................................
Before You Begin 1. Before You Begin What Is Included • Nexus™ 4x4 • Neutrik® powerCON® power input cable • #5 Allen wrench • Alternate bracket • Warranty card • Quick Reference Guide Claims Carefully unpack the product immediately, and check the box to make sure all the parts are in the package and are in good condition. If the box or the contents (the product and included accessories) appear damaged from shipping or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Before You Begin Safety Notes Read all the following Safety Notes before working with this product. These notes include important information about the installation, usage, and maintenance of this product. This product contains no user-serviceable parts. Any reference to servicing in this User Manual will only apply to properly trained CHAUVET® certified technicians. Do not open the housing or attempt any repairs. All applicable local codes and regulations apply to proper installation of this product.
Introduction 2. Introduction Description Features Nexus™ 4x4 is a tour-ready wash light capable of delivering a pixel mapping display and an output of sixteen 27-watt RGB COB LEDs. The combination of COB emitters and a clever reflector design yields a diffused light with saturated hues. Nexus™ 4x4 is controllable via Art-Net™, Kling-Net, and DMX protocols. It also features interlocking hardware to build large arrays.
Introduction Overview COB LEDs Yoke Adjustment Knob Side View Front View Coffin Lock Access Control Panel Coffin Lock Access Coffin Lock Power I/O Ethernet I/O 5-Pin DMX I/O 3-Pin DMX I/O Rear View Nexus™ 4x4 User Manual Side View -5-
Introduction Dimensions -6- Nexus™ 4x4 User Manual
Setup 3. Setup AC Power The Nexus™ 4x4 has an auto-ranging power supply that works with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the power requirements for each Nexus™ 4x4, refer to the label affixed to the product. You can also refer to the Technical Specifications section in this manual. The listed current rating indicates the maximum current draw during normal operation. For more information, you may download Sizing Circuit Breakers from the CHAUVET® website: www.chauvetpro.com.
Setup Power Linking The Nexus™ 4x4 supports power linking. You can power link up to: • 4 products at 120 VAC, or • 8 products at 230 VAC This product comes with a power input cord. This product does not come with a power linking cable; however, a power linking cable is available as an option.
Setup DMX Linking You can link the Nexus™ 4x4 to a DMX controller using a standard DMX serial connection. If using other DMX compatible products with the Nexus™ 4x4, you can control each individually with a single DMX controller. DMX Modes The Nexus™ 4x4 uses the standard DMX data connection for the 3, 5, 9, 48 and 53 channel DMX modes. • Refer to the Introduction section for a brief description of these modes.
Setup Art-Net™ Connection Art-Net™ is an Ethernet protocol that uses TCP/IP to transfer large amounts of DMX512 data over a network. Art-Net™ uses the Neutrik® etherCON® connection. An Art-Net™ protocol document is available from www.chauvetpro.com. Art-Net™ is designed and copyright by Artistic License Holdings Ltd. The Art-Net™ protocol is designed to work with nodes and Ethernet hubs, or switches in “Star Topology”.
Setup Mounting Before mounting this product, read and follow the guidelines outlined in the Safety Notes section. Orientation Always mount this product in a safe position and make sure there is adequate room for ventilation, configuration, and maintenance. Rigging The Nexus™ 4x4 consists of a bracket and body. CHAUVET® recommends using the following guidelines when mounting this product.
Setup Floor/Wall Mounting -12- Nexus™ 4x4 User Manual
Setup Pipe/Truss Mounting #5 Allen Key Only use the coffin locks to align the product; it is not intended to be used for bearing weight. Do not hang the product only using the coffin locks.
Operation 4.
Operation Display Backlight This setting determines how long the backlight on the display stays on. 1. Go to the Back Lite main level. 2. Select the desired amount of time the backlight display will stay on after pressing the last menu button (On, 10 S, 20 S, or 30 S). Product Information This menu option provides software information that is needed for certain programming functions and software uploads. 1. Go to the Info main level. 2. Select the desired program level based on the information required.
Operation White Calibration This setting allows you to define the color temperature used when the DMX controller’s faders (red, green, blue) are set to “255.” 1. Go to the White main level. 2. Select the desired color (R, G, or B). 3. Select the desired color value (125~255). 4. Repeat the steps for each color. Fan Control The Nexus™ 4x4 allows you to adjust the fan speed for quiet operation. 1. Go to the Fan Speed main level. 2. Select the desired speed (High or Auto).
Operation Nexus™ 4x4 Software Upgrade Instructions The following steps were used in the Windows® 7 operating system environment. Step 1: 1. Connect the Nexus™ 4x4 to the router. 2. Verify the computer is using the same network as the Nexus™ 4x4 product. Step 2: 1. From the Nexus™ 4x4 main level, navigate to the Ethernet Settings. Ethernet Settings Step 3: 1. Select Protocol. 2. Select Art-Net. 3. Select IP Mode (verify the Static setting is selected). Protocol Step 4: 1.
Operation Step 5: 1. Select the desired network the product is connected to. NOTE: If you are running a hard-wired line from the PC to your router, then select Local Area Connection). The Local Area Connection Status dialog appears. 2. Click Properties. The Local Area Connection Properties dialog appears. Step 6: 1. From the Networking tab, select Internet Protocol Version 4 (TCP/IPv4). 2. Click Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties dialog appears. Step 7: 1.
Operation Step 8: 1. From the Nexus™ 4x4 control panel, navigate to the Info main level. 2. Select IP Address. 3. From the PC, open the Internet browser. 4. Enter the IP address for the Nexus™ 4x4 you are working with in the address bar. For example, if the IP address shown in the product’s control panel is 2.34.58.104, then type that into your internet browser address bar). 5. Press ENTER. The Authentication Required dialog appears. Step 9: 1. Enter the following information: c.
Operation Step 12: 1. Navigate to the Info main level. 2. Select Version. 3. Verify the product’s control panel displays the uploaded version. CHAUVET Lighting Nexus 4x4 v. x.xx The software upgrade is now complete. Step 13: Once the software upgrade is complete, the IP setting on your PC needs to be changed back to the original settings. 1. Refer to step #4 for navigation instructions on how to access the Internet Protocol Version 4 Properties (TCP/IPv4) dialog. 2.
Operation Menu Map Main Level Auto Show Programming Levels Auto 01~12 Description Show Speed 000~100 13 automatic programs Fade R G B Fixture Color GB 7 preset colors RB Static RG RGB R Manual Color G B Dimmer Mode Off Dimmer 1~3 On Back Lite 20S Fixture Hours DMX Address DMX Channel Nexus™ 4x4 User Manual Combine Red, Green, and Blue, to generate a custom color (0~100%) Dimming curve Always on 10S 30S Info 000~255 Version Sets the amount of time control panel backlight stays on Sh
Operation Menu Map (Cont.
Operation DMX Values 53 Ch Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Nexus™ 4x4 User Manual Function Red 1 Warm White 1 Green 1 Cool White 1 Blue 1 Red 2 Warm White 2 Green 2 Cool White 2 Blue 2 Red 3 Warm White 3 Green 3 Cool White 3 Blue 3 Red 4 Warm White 4 Green 4 Cool White 4 Blue 4 Red 5 Warm White 5 Green 5 Cool White 5 Blue 5 Red 6 Warm White 6 Green 6 Cool White 6 Blue 6 Red 7 Warm White 7 Green 7 Cool White 7 Blue 7 Red 8 Warm White 8 Green 8 Cool
Operation DMX Values (Cont.) 53 Ch Channel Function (Cont.
Operation DMX Values (Cont.
Operation DMX Values (Cont.
Operation DMX Values (Cont.
Technical Information 5. Technical Information Product Maintenance To maintain optimum performance and minimize wear, you should clean this product frequently. Usage and environment are contributing factors in determining the cleaning frequency. As a rule, clean this product at least twice a March. Dust build-up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear. To clean your product: • Unplug the product from power.
Technical Information Technical Specifications Dimensions and Weight Length Width Height Weight 18.2 in (462 mm) 18.2 in (462mm) 14.17 in (360 mm) 26.6 lb (12.07 kg) Note: Dimensions in inches rounded to the nearest decimal digit.
Headquarters Contact Us World CHAUVET® United Kingdom and Ireland CHAUVET® Europe Ltd. General Information Address: Voice: Fax: Toll free: 5200 NW 108th Avenue Sunrise, FL 33351 (954) 577-4545 (954) 929-5560 (800) 762-1084 General Information Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115 Fax: +44 (0)1773 511110 Technical Support Voice: Fax: Email: (954) 577-4455 (Press 4) (954) 756-8015 tech@chauvetlighting.
