User Manual
Table of Contents 1. Before You Begin ........................................................................... 3 What Is Included ........................................................................................... 3 Unpacking Instructions .................................................................................. 3 Claims ........................................................................................................... 3 Text Conventions ...........................................
1. Before You Begin What Is Included • • • • • Hurricane™ Haze 2D Power Cord Timer Remote (15 ft length) Warranty Card Quick Reference Guide Unpacking Instructions Immediately upon receiving this product, carefully unpack it and check the container in which you received it. Claims If the container or the material inside the container (the product and included accessories) appear damaged from shipping, or show signs of mishandling, upon receipt notify the carrier immediately, not Chauvet.
Product at a Glance Use on Dimmer x Auto Programs x Outdoor Use Sound-Activated x x P x Auto-ranging Power Supply Replaceable Fuse x P x x DMX Master/Slave User-Serviceable Duty Cycle Safety Notes Please read the following Safety Notes carefully before working with the product. The Notes include important safety information about installation, usage, and maintenance. • Always connect the product to a grounded circuit to avoid the risk of electrocution.
2. Introduction Product Overview Control Board DMX In DMX Out Wired Remote Power Switch Fuseholder Power In Rubber feet (4) Fluid & wired remote storage access panel Hurricane™ Haze 2D User Manual Rev.
Product Dimensions Page 6 of 16 Hurricane™ Haze 2D User Manual Rev.
3. Setup AC Power This product can work with an input voltage of either 120 VAC, 60 Hz or 230 VAC, 50 Hz depending on the model. To determine the power requirements for a particular product, see the label affixed to the back plate of the product or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Mounting Orientation The Hurricane™ Haze 2D may be mounted in any position provided there is adequate room for ventilation around it. Rigging Be sure that the structure or surface onto which you are mounting this product can support its weight. Please see the Technical Specifications section of this manual for weight information. Make sure to mount the product securely to a rigging point, whether an elevated platform or a truss.
4. Operation Control Panel Operation To access the control panel functions, use the three buttons located underneath the display. Button Function
Wired Timer Remote Operation Important: Using the Control Board, set the Fan and Haze output to 0. You can then connect and operate the included wired remote with the Hurricane™ Haze 2D. The wired timer controller allows you to automatically trigger fog output by setting interval and duration times. LED indicator lights display the machine and controller’s current state. Rotary knobs set interval and duration times, while manual and continuous buttons allow overriding control. 1.
Menu Map Mode DMX Mode Manual Mode Configuration (DMX) Starting Address Programming Steps Description d*** 001–512 Haze Volume h001–h005 Low–high Blower Speed f001–f005 Low–high Selects the DMX starting address Set this product in DMX mode to control it with a DMX controller. • Connect this product to a suitable power outlet. • Turn this product on. • Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket of this product.
Configuration (Standalone Mode) Set this product in one of the standalone modes to control it without a DMX controller. 1. Connect this product to a suitable power outlet. 2. Turn this product on. Manual Mode Never connect a product that is operating in any standalone mode, whether Static, Automatic, or Sound to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.
5. Technical Information Hazer Maintenance Do not allow the hazer to become clogged. After every 40 hours of continuous operation, use CHAUVET® Fog Cleaner Quart (FCQ) through the system to prevent the accumulation of particulate matter in the heating element. The recommended cleaning procedure is as follows. 1. Unplug the product from power. 2. Empty all fog fluid from the machine. 3. Add cleaning solution to the tank. 4. Connect the product to power and allow it to warm up. 5.
General Troubleshooting Symptom Indicator Status Red Possible Cause Heater warming up Possible Action Allow the product to warm up completely. This should take less than 10 minutes. Allow the product to warm up completely. Red flashing Air bubble in fluid line Turn fog machine 45° to flatten out the bubble and allow the fog fluid to flow properly Turn off the product for 5 seconds, and then turn it back on. Repeat as necessary. Note: After more than 10 attempts, contact Customer Service.
RETURNS To return a product or request support: • In the U.S., contact Chauvet World Headquarters (see Contact Us). • In the UK or Ireland, contact Chauvet Europe Ltd. (see Contact Us). • In Mexico, contact Chauvet Mexico (see Contact Us). • In any other country, DO NOT contact Chauvet. Contact your distributor. See www.chauvetlighting.com for distributors outside the U.S., United Kingdom, Ireland, or Mexico. If you live outside the U.S.
6. Technical Specifications Dimensions and Weight Length Width Height Weight 11.2 in (285 mm) 10.5 in (267 mm) 13.7 in (350 mm) 18.7 lb (8.5 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Operation Fog output Power Supply Type Range Voltage Selection Model-specific 120 V, 60 Hz or 230 V, 50 Hz Fixed voltage Parameter 120 V, 60 Hz 230 V, 50 Hz Consumption 533 W (4.4 A) 533 W (2.