User Manual
TABLE OF CONTENTS 1. Before You Begin .......................................................................................................... 3 What Is Included ............................................................................................................................... 3 Unpacking Instructions ..................................................................................................................... 3 Claims ....................................................................
1. BEFORE YOU BEGIN What Is Included • • Intimidator™ Beam LED 350 Hanging bracket with mounting hardware • • • Power cord Warranty card Quick Reference Guide Unpacking Instructions Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. Claims If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Product at a Glance Use on Dimmer Outdoor Use Sound-Activated DMX Master/Slave Safety Notes Auto Programs Auto-ranging Power Supply Replaceable Fuse User-Serviceable P P P x These notes include important information about the mounting, usage, and maintenance of this product; read before using the product. • • • • • • • • • • • • • • • • • • • • • Page 4 of 19 x x P P P This product is not intended for permanent installation.
2. INTRODUCTION Overview Power In Fuse Holder DMX In/Out Power Out Safety Loop Intimidator™ Beam LED 350 User Manual Rev.
Dimensions 18.5 in (470 mm) Page 6 of 19 Intimidator™ Beam LED 350 User Manual Rev.
3. SETUP AC Power The Intimidator™ Beam LED 350 has an auto-ranging power supply and it can work with an input voltage range of 100–240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Power Linking The product provides power linking via the Edison/IEC outlet located in the back of the unit. st 1 Product Power Linking Diagram nd 2 Product rd 3 Product Other Products You can power link up to 3 Intimidator™ Beam LED 350 units on 120 VAC or up to 7 Intimidator™ Beam LED 350 units on 230 VAC.
Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. For the CHAUVET® line of mounting clamps, go to www.chauvetlighting.com/cables-clamps-main.html/. Orientation The Intimidator™ Beam LED 350 may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display.
Starting Address When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. The Intimidator™ Beam LED 350 uses up to 14 DMX channels in 14-CH DMX mode, which defines the highest configurable address to 499. If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com. To select the starting address, do the following: 1.
8-CH (cont.
14-CH (cont.) Channel Function 7 Gobo Wheel 8 No Function 9 Prism/Frost 10 11 No Function Dimmer Intimidator™ Beam LED 350 User Manual Rev.
-CH (cont.
Configuration (Standalone) Set the product in one of the standalone modes to control without a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. Never connect a product that is operating in any standalone mode (either Automatic, or Sound-Active) to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.
Display Master/Slave Mode To flip the LED display for better readability in any mounting situation, do the following: 1. Press repeatedly until diS or rdiS shows on the display. 2. Press or to select diS (normal display mode) or rdiS (inverse display mode). 3. Press . The Master/Slave mode allows a single Intimidator™ Beam LED 350 unit (the master) to control the actions of one or more Intimidator™ Beam LED 350 units (the slaves) without the need of a DMX controller.
5. TECHNICAL INFORMATION Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, clean the product at least twice a month. However, usage and environmental conditions contribute to increased cleaning frequency. To clean the product, follow the instructions below: • Unplug the product from power.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 11.3 in (287 mm) 13.4 in (340 mm) 18.5 in (470 mm) 22 lb (9.8 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Light Source Photo Optic Thermal DMX Ordering Page 18 of 19 Power Supply Type Range Voltage Selection Switching (internal) 100–240 VAC, 50/60 Hz Auto-ranging Parameter 120 V, 60 Hz 230 V, 50 Hz Consumption 258 W 269 W Operating current 2.1 A 1.
To return a product or request support: • • • • In the U.S., contact CHAUVET® World Headquarters. In the UK or Ireland, contact CHAUVET® Europe Ltd. In Mexico, contact CHAUVET® Mexico. In any other country, DO NOT contact CHAUVET®. Contact your distributor. If you live outside the U.S., United Kingdom, Ireland, or Mexico, contact your distributor of record and follow their instructions on how to return CHAUVET® products to them. Visit our website for contact details.