User Manual
TABLE OF CONTENTS 1. Before You Begin ...........................................................................................................3 What Is Included ......................................................................................................................... 3 Unpacking Instructions ................................................................................................................ 3 Claims ...............................................................................
1. BEFORE YOU BEGIN What Is Included Unpacking Instructions Claims Text Conventions Symbols • • • • • • LFS-75DMX Power cord 4 metal gobos 4 framing shutters Warranty card Quick Reference Guide Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Product at a Glance Use on Dimmer Outdoor Use Sound-Activated DMX Master/Slave Safety Notes Auto Programs Switchable voltage (120 V/230 V) Replaceable Fuse User-Serviceable P P P x These notes include important information about the mounting, usage, and maintenance of this product; read before using the product. • • • • • • • • • • • • • • • • • • • • Page 4 of 17 x x x P P Always connect the product to a grounded circuit to avoid the risk of electrocution.
2.
Overview (cont.
Dimensions 15.1 in 385 mm 11.1 in 283 mm 13.
3. SETUP AC Power The LFS-75DMX has a dual voltage power supply and it can work with an input voltage of either 120 V, 60 Hz or 230 V, 50 Hz, depending on the position of the voltage selection switch. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
Power Linking The product provides power linking via the Edison/IEC outlet located in the top of the unit. st Power Linking Diagram 1 Product 2nd Product 3rd Product Additional Products You can power link up to 8 LFS-75DMX units on 120 VAC or up to 14 LFS-75DMX units on 230 VAC.
Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The LFS-75DMX may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display.
DMX Channel Modes, Assignments, and Values 4-Channel Channel Function 1 Dimmer 2 Strobe 3 Fan Speed 4 Color Wheel Value 000 ó 000 ó 004 ó 008 ó 216 ó 000 ó 002 ó 000 ó 007 ó 014 ó 021 ó 028 ó 035 ó 042 ó 049 ó 056 ó 064 ó 071 ó 078 ó 085 ó 092 ó 099 ó 106 ó 113 ó 120 ó 128 ó 192 ó 255 003 007 215 255 001 255 006 013 020 027 034 041 048 055 063 070 077 084 091 098 105 112 119 127 191 255 Setting 0 to 100% Light off Light on Strobe (slow to fast) Light on Automatic Manual (slow to fast) White Yel
Configuration (Standalone) Set the product in the standalone Manual mode to control without a DMX controller. • Connect the product to a suitable power outlet. Never connect a product that is operating in a standalone mode to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Manual Mode To enable the Manual mode, do the following: 1. Press repeatedly until MAN shows on the display.
Included Gobos Changing Gobos To change the gobos in the LFS-75DMX, do the following: 1. Disconnect the product from power. 2. Place the product on a flat, level surface. 3. Loosen the gobo door thumbscrew and pull off the gobo door. 4. Pull up the gobo holder out of the product. 5. Remove the gobo from between the slats of the gobo holder. 6. Insert a new gobo between the slats of the gobo holder. 7. Push the gobo holder back down into place. 8. Replace the gobo door and tighten the gobo door thumbscrew.
5. TECHNICAL INFORMATION Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, clean the product at least twice a month. However, usage and environmental conditions contribute to increased cleaning frequency. To clean the product, follow the instructions below: • Unplug the product from power.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 15.1 in (385 mm) 11.1 in (283 mm) 13.6 in (345 mm) 8 lb (3.7 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Light Source Photo Optic Thermal DMX Ordering Page 16 of 17 Power Supply Type Range Voltage Selection Switching (external) 120/230 V, 50/60 Hz Switchable Parameter 120 V, 60 Hz 230 V, 50 Hz 206 W Consumption 198 W Operating current 1.6 A 0.
To return a product or request support: • • • In the U.S., contact CHAUVET® World Headquarters (see below). In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below). In any other country, DO NOT contact CHAUVET®. Contact your distributor. See www.chauvetlighting.com for distributors outside the U.S., United Kingdom, or Ireland. If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of record and follow their instructions on how to return CHAUVET® products to them.
