User Manual
TABLE OF CONTENTS 1. Before You Begin ...........................................................................................................3 What Is Included ......................................................................................................................... 3 Unpacking Instructions ................................................................................................................ 3 Claims ...............................................................................
1. BEFORE YOU BEGIN What Is Included • • • • • • • • COREbar™ 4 Power Cord Carrying bag (x 2) L-brackets (x 2) Tripod Footswitch Warranty Card Quick Reference Guide Unpacking Instructions Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. Claims If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Product at a Glance Use on Dimmer Outdoor Use Sound-Activated DMX Master/Slave Safety Notes Auto Programs Auto-ranging Power Supply Replaceable Fuse User-Serviceable P P P x These notes include important information about the mounting, usage, and maintenance of this product; read before using the product. • • • • • • • • • • • • • • • • • • • • Page 4 of 16 x x P P P Always connect the product to a grounded circuit to avoid the risk of electrocution.
2.
Dimensions 29.5 in 749 mm 11.2 in 285 mm 5.
3. SETUP AC Power The COREbar™ 4 has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Power Linking The product provides power linking via the Edison/IEC outlet located in the back of the unit. st 1 Product Power Linking Diagram 2nd Product rd 3 Product Additional Products You can power link up to 8 COREbar™ 4 units on 120 VAC or up to 16 COREbar™ 4 units on 230 VAC.
Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The COREbar™ 4 may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display.
DMX Channel Modes, Assignments, and Values 15-Channel 3-Channel COREbar™ 4 User Manual Channel Function Value 000 ó 010 ó 030 ó 050 ó 070 ó 090 ó 110 ó 130 ó 150 ó 170 ó 190 ó 210 ó 230 ó 250 ó 000 ó 000 ó 010 ó 009 029 049 069 089 109 129 149 169 189 209 229 249 255 255 009 255 Setting No function Auto program 1 Auto program 2 Auto program 3 Auto program 4 Auto program 5 Auto program 6 Auto program 7 Auto program 8 Auto program 9 Auto program 10 Auto program 11 Auto program 12 Sound-Active mode 0—10
Configuration (Standalone) Set the product in one of the standalone modes to control without a DMX controller. • Connect the product to a suitable power outlet. Never connect a product that is operating in any standalone mode (Static, Automatic, or Sound-Active) to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Sound-Active Mode To enable the Sound-Active mode, do the following: 1.
Master/Slave Mode Footswitch Master/Slave Connection COREbar™ 4 User Manual The Master/Slave mode allows a single COREbar™ 4 unit (the “master”) to control the actions of one or more COREbar™ 4 units (the “slaves”) without the need of a DMX controller. The master unit will be set to operate in either Automatic or Sound-Active mode, while the slave units will be set to operate in Slave mode. Once set and connected, the slave units will operate in unison with the master unit.
5. TECHNICAL INFORMATION Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, clean the product at least twice a month. However, usage and environmental conditions contribute to increased cleaning frequency. To clean the product, follow the instructions below: • Unplug the product from power.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 29.5 in (749 mm) 5.3 in (135 mm) 11.2 in (285 mm) 8.8 lb (4 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Light Source Photo Optic Thermal DMX Tripod Ordering COREbar™ 4 User Manual Power Supply Type Range Voltage Selection Switching (internal) 100~240 V, 50/60 Hz Auto-ranging Parameter 120 V, 60 Hz 230 V, 50 Hz 116 W Consumption 109 W Operating current 0.9 A 0.
To return a product or request support: • • • In the U.S., contact CHAUVET® World Headquarters (see below). In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below). In any other country, DO NOT contact CHAUVET®. Contact your distributor. See www.chauvetlighting.com for distributors outside the U.S., United Kingdom, or Ireland. If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of record and follow their instructions on how to return CHAUVET® products to them.
