User Manual
Edition Notes Edition Notes This User Manual covers the description, safety precautions, setup, installation, operation, and maintenance for the MVP™ Ta8 Curve video panels offered by CHAUVET®. This edition was published in October 2012. Trademarks CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or Chauvet).
Table of Contents Table of Contents Edition Notes ...............................................................................................................................................................ii Trademarks ............................................................................................................................................................................ ii Copyright Notice ...............................................................................................
Table of Contents Step 1 .................................................................................................................................................................................... 16 Step 2 .................................................................................................................................................................................... 16 Step 3 .........................................................................................................
Introduction 1. Before You Begin What Is Included Unpacking Instructions • 2 or 6 MVPs (Modular Video Panel) Ta8 Curve • Neutrik® etherCON® Signal Cable per MVP™ Ta8 Curve 0.65 m/25.2 in • Neutrik® powerCON® Power Cable per MVP™ Ta8 Curve 0.65 m/25.2 in • 2- or 6-Pack Flight Case (based on the number of MVPs included) • Warranty Card • User Manual Immediately upon receiving this product, carefully unpack and check the container. Make sure you have received all the parts indicated above in good condition.
Introduction Safety Notes Please read the following Safety Notes carefully before working with the product. These notes provide important safety information about installation, usage, and maintenance. This product contains no user-serviceable parts. Any reference to servicing in this User Manual will only apply to properly trained CHAUVET® certified technicians. Do not open the housing or attempt any repairs.
Introduction 2. Introduction Product Description The MVP™ Ta8 Curve is a Modular Video Panel. Each video panel consists of multiple SMD3528 tri-color LEDs. The number in the model name indicates the pixel pitch (distance, in millimeters, between the LEDs. When multiple panels are assembled and connected (signal and power), the entire configuration becomes a modular video wall design. The outer dimensions of each panel are identical.
Introduction Overview 4- MVP™ Ta8 Curve User Manual, Rev.
Introduction Dimensions Pixels Per Panel Each pixel is one SMD3528 LED. For detailed specifications, refer to the Technical Specifications. MVP™ Ta8 Curve Pixels per Panel Total Pixels 72 x 72 5,184 You will use the number of pixels per panel and the screen resolution you would like to use for your video wall display to calculate the number of panels, horizontally and vertically, supported by a single VIP™ Driver. This Driver is required to operate a CHAUVET® VIP™ video wall system.
Introduction 3. Setup AC Power Each MVP™ Ta8 Curve has an auto-ranging power supply that works with an input voltage range of 100~240 VAC, 50/60 Hz. Make sure that you are connecting the MVPs to the proper voltage, as specified in this User Manual and on the product’s specification sticker. Always connect this product to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire.
Setup 4. Mounting the MVPs Orientation Each MVP™ Ta8 Curve is a solid frame constructed of aluminum alloy and stainless steel. This ensures each panel is stable and easy to install. Each panel also has a convenient pop-out handle located on the top, outside, of the panel. This handle enables you to easily pick up and securely hold each panel while mounting and working with the panels. The MVPs can be assembled to provide any number of modular designs.
Joining Each MVP™ (Creating a Modular Design) 5. Joining Each MVP™ (Creating a Modular Design) Each MVP™ Ta8 Curve is joined together to create a modular designed video wall. Because the panels are interchangeable, you can create a video wall by joining several of the same model or joining different models to create a larger or more complex video wall.
Joining Each MVP™ (Creating a Modular Design) Horizontally Joining Panels Step 1 Each MVP™ Ta8 Curve can be easily joined horizontally using the 2 horizontal locking knobs on the inside left-hand top and bottom of each panel to connect them in a straight 90° orientation or they can be joined using the adjustable locking arms on the inside right-hand top and bottom of each panel. Using the adjustable locking arms allows the panels to be curved +/- 18°.
Joining Each MVP™ (Creating a Modular Design) Step 1 Step 2 Step 3 Horizontal Joining Use the following instructions to join your panels horizontally. Procedure 1. Loosen locking/adjustment knobs and pull arms out as shown in step 1 and 2. Pull together adjoining panel, set the same angle on both arms and lightly tighten (+/- 18°) 2. adjustment knobs as shown in step 2. (This is for connection only and can be readjusted later.) 3.
Connecting (Cabling) Each MVP™ 6. Connecting (Cabling) Each MVP™ Testing Signal and Power Connections Each MVP™ Ta8 Curve has two (2) power supply sockets and two (2) signal sockets. • The Power and Signal IN are located on the upper right-hand side of each panel. • The Power and Signal OUT are located on the upper left-hand side of each panel. • The Signal IN and OUT may be used interchangeably. Each MVP™ Ta8 Curve has LED indicator lights.
Connecting (Cabling) Each MVP™ Connecting the Signal Input The VIP™ video wall system uses 2 basic setup configurations to connect the signal to the video wall: 1. A configuration using 24 or less panels. 2. A configuration using more than 24 panels. The next section, Connecting Power and Signal Cables, gives information on connecting power and signal between joined panels and to the rest of the VIP™ system.
Connecting (Cabling) Each MVP™ Connecting Power and Signal Cables The following sections provide information and diagrams on connecting signal and power between panels. Refer to the Introduction or Operation sections in this User Manual for available cables and item numbers. Connecting the Signal Between Joined Panels Signal cable panel connections can use several different configurations. The basic configuration to connect the signal from one panel to the next is as follows.
Connecting (Cabling) Each MVP™ The following diagram shows an example of a signal connection configuration using more than 24 panels. A video wall design with more than 24 panels requires: • Incoming signal connection to the VIP™ Driver. • VIP™ Driver connection to the VIP™ Signal Distributor. • Signal cable connections as determined by the number of panels in the video wall design and the desired layout, for ease of setup.
Connecting (Cabling) Each MVP™ Connecting the Power Between Joined Panels Power cable panel connections can also use different configurations. The basic configuration to connect the main power supply from one panel to the next is: • The main power is connected to the first panel’s Power Input or Output. • A powerCON® cable is then connected to the first panel’s Power Output and connected to the next panel’s Power Input. • The connections continue until all panels are connected.
Typical MVP™ Installation 7. Typical MVP™ Installation Because a video wall system can include different components to provide a simple to complex modular wall design, use the following steps as a general guide to get started. Step 1 Open and examine the MVP™ Ta8 Curve flight case to make sure you have received all products and accessories and that each one is in good condition.
Typical MVP™ Installation VIP™ Sample Video Wall System Setup The following diagram provides a sample setup for a CHAUVET® VIP™ video wall system. This system setup includes an optional signal processor for additional video sources, and the VIP™ Signal Distributor to support more than 24 panels. Note that the two-driver setup shown here allows for simultaneous playback of pre-recorded and live content, all directed from a single PC.
Operation 8. Operation Additional Hardware and Software In addition to the panels, you will need other hardware and software to design, build, and operate your VIP™ video wall system. The following table summarizes these additional items—some are required and others are optional. Item Description VIP™ Driver Interface between the signal source, LED Studio, and the MVP™ Ta8 Curve being used Software application used to design and run the MVPs comprising the video wall.
Operation About CHAUVET® LED Studio CHAUVET® LED Studio is a powerful and easy-to-learn software application used to design and run the VIP™ video wall system. The following is some introductory information about this software. Refer to the CHAUVET® LED Studio User Manual for detailed information and instructions on setting up and using CHAUVET® LED Studio with your CHAUVET® VIP™ video wall system.
Technical Information 9. Technical Information MVP™ Ta8 Curve Maintenance To maintain optimum performance and minimize wear, the user should clean this product regularly. Usage and environment are contributing factors in determining the cleaning frequency. As a rule, clean this product at least twice a month. Dust build-up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear.
Technical Information Returns Send the merchandise prepaid, in the original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause(s) for the return. Clearly label the package with an RMA number. CHAUVET® will refuse any product returned without an RMA number.
Technical Information 10. Technical Specifications MVP™ Ta8 Curve Light Source Pixels per Panel Pixel Pitch (between LEDs) Pixel Density Display Refresh Rate Tri-color SMD3528 LED 72 x 72 (5,184 total) 8.
Headquarters Contact Us World CHAUVET® United Kingdom and Ireland CHAUVET® Europe Ltd. General Information Address: Voice: Fax: Toll free: 5200 NW 108th Avenue Sunrise, FL 33351 (954) 929-1115 (954) 929-5560 (800) 762-1084 General Information Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115 Fax: +44 (0)1773 511110 Technical Support Voice: Fax: Email: (954) 929-1115 (Press 4) (954) 756-8015 tech@chauvetlighting.com World Wide Web www.