Snapshot OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave Autoswitching transformer Replaceable Fuse User Serviceable Duty Cycle USER MANUAL 3000 N 29th Ct, Hollywood, FL 33020 U.S.A. (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.
TABLE OF CONTENTS 1. BEFORE YOU BEGIN ................................................................................................................................................... 3 WHAT IS INCLUDED ................................................................................................................................................................................ 3 UNPACKING INSTRUCTIONS ........................................................................................................
1. BEFORE YOU BEGIN What is included 1 x Q-Spot™ 150-LED 1 x Set of 3 extra gobos 1 x Bracket set 1 x Power Cord 1 x Warranty Card 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture.
2.
Product Overview Menu Up Enter Down DMX in DMX out Power on/off switch Power input/fuse holder Cooling fan vent Q-Spot™ 150-LED User Manual 6 9/22/2009 3:57 PM
Product Dimensions Q-Spot™ 150-LED User Manual 7 9/22/2009 3:57 PM
3. SETUP Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement 1) With a flat head screwdriver wedge the fuse holder out of its housing. 2) Remove the damaged fuse from its holder and replace with exact same type and rating fuse. 3) Insert the fuse holder back in its place. 4) Reconnect power. Replacing Gobos 1) Remove the gobo cover. 2) Remove the slot-n-lock gobo from the gobo wheel.
Gobo and Color Wheel Diagrams Q-Spot™ 150-LED User Manual 9 9/22/2009 3:57 PM
Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. Important: Fixtures on a serial data link must be daisy chained in one single line.
3-Pin to 5-Pin Conversion Chart Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. The chart below details a proper cable conversion: 3 PIN TO 5 PIN CONVERSION CHART Conductor 3 Pin Female (output) 5 Pin Male (Input) Ground/Shield Pin 1 Pin 1 Data ( - ) signal Pin 2 Pin 2 Data ( + ) signal Pin 3 Pin 3 Do not use Pin 4 Do not use Pin 5 Setting up a DMX Serial Data Link Universal DMX Controller 1.
Mounting Orientation This fixture may be mounted in a vertical hanging or floor mounted position, provided there is adequate room for ventilation. Rigging It is important never to obstruct the fan or vents pathway. Mount the fixture, using a suitable “C” or “O” type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. When selecting installation location, take into consideration access and routine maintenance.
4. OPERATING INSTRUCTIONS Navigating the Control Panel Button Function
Menu Map MAIN FUNCTION SUB-FUNCTION 1.1 Address SELECTION 000 ~ 255 1.2 Reset Yes ~ No DMX-512 Auto_1 Auto_2 Sound_1 1.3 Operation Sound_2 1-Intro Custom Test Slave 1.4 Channels Advanced Basic 60 close 1.5 Display Bright 1.6 Info 2.1 Pan 2.2 Tilt 2-Invert Edition Normal Reverse Normal Reverse Step 2.3 Color Linear 3-Range 2.4 Use No ~ Yes 3.1 P/start 000 ~ 255 3.2 P/Finish 000 ~ 255 3.3 T/start 3.4 T/Finish 000 ~ 255 000 ~ 255 3.5 Use No ~ Yes 4.1 Black No ~ Yes 4-Special DMX 4.
Menu Functions Service Functions To test the fixture: 1) Use the “Test” function under the “1.3 Operation” menu (see page 14). To reset the fixture: 1) Use the “4.2 Reset” function under the “4-Special” menu (see page 14). To restore all settings to their factory defaults: 1) Use the “6.1 Default” function under the “6-Default” menu (see page 14). Operation Master/Slave Mode (Master Sound, Master Auto): This mode will allow you to link up to 32 units together without a controller.
Advanced (16-bit) CHANNEL VALUE FUNCTION 1 000 255 Pan 0°~530° 2 000 255 Pan fine Fine pan adjustment 3 000 255 Tilt 0°~270° 4 000 255 Tilt fine Fine tilt adjustment 5 000 255 Pan/tilt Speed Normal > Slow 000 014 015 029 030 044 045 059 060 074 075 089 090 104 105 119 120 134 135 149 150 255 Color Open Red Yellow Green Pink Blue Orange Magenta Light blue Light green Color scroll (slowfast) 000 009 010 019 020 029 030 039 040 049 050 059 060
Basic (8-bit) CHANNEL VALUE FUNCTION 1 000 255 Pan 0°~530° 2 000 255 Tilt 0°~270° 000 014 015 029 030 044 045 059 060 074 075 089 090 104 105 119 120 134 135 149 150 255 Color Open Red Yellow Green Pink Blue Orange Magenta Light blue Light green Color scroll (slowfast) 000 009 010 019 020 029 030 039 040 049 050 059 060 069 070 079 080 099 100 119 120 139 140 159 160 179 180 199 200 219 220 255 Gobo Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo
Setting the DMX Starting Address This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address" from 1 to 512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that uses 6 DMX channels and was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105.
General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced LED life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power.
Q-Spot™ 150-LED Troubleshooting Symptom Beam is very dim or not bright Breaker/Fuse keeps blowing Device has no power Solution(s) Clean optical SYSTEM Check total load placed on device Moves slow Check for power on Mains. Check device’s fuse. (internal and/or external) Check DMX Dip switch settings for correct addressing Check DMX cables Check polarity switch settings Make sure you have the correct audio mode on the control switches.
Exploded View 26 19 5 20 16 17 18 25 3 28 2 23 6 27 10 7 1 20 8 4 21 Description Part Number 1 Display PCB P170-QS1DIS 2 Driver PCB (in side arm) 3 24 29 Description Part Number 16 Color Wheel P150-QS1COW P255-QS1DRA 17 Gobo wheel P115-QS1GOW Driver PCB (in head) P255-QS1DRH 18 Color motor P110-QS1COM 4 Electronic Transformer P140-QS1ELTR 19 Gobo motor P110-QS1GOM 5 20W LED (white) P222-QS1LED 20 Gobo Rot.
Photometrics Technical Specifications WEIGHT & DIMENSIONS Length .......................................................................................................................... 9.5 in (242 mm) Width.......................................................................................................................... 9.47 in (240 mm) Height ........................................................................................................................ 14.3 in (364 mm) Weight...........
