Intimidator™ Spot 150 Snapshot OK on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle USER MANUAL 3000 N 29th Ct, Hollywood, FL 33020 U.S.A. (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.
TABLE OF CONTENTS 1. Before You Begin .................................................................................................................................................................. 3 What is included .......................................................................................................................................................................... 3 Unpacking Instructions ................................................................................................
1. BEFORE YOU BEGIN What is included 1 x Intimidator™ Spot 150 1 x Mounting bracket kit w/screws 1 x Power Cord 1 x Warranty Card 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture.
2.
DMX Channel Summary Advanced Mode Basic Mode CHANNEL FUNCTION CHANNEL FUNCTION 1 Pan 1 Pan coarse 2 Tilt 2 Tilt coarse 3 Color 3 Pan fine 4 Gobo 4 Tilt fine 5 Gobo rotation 5 Pan/Tilt speed 6 Shutter 6 Color 7 Dimmer 7 Gobo 8 Effect 8 Gobo rotation 9 Shutter 10 Dimmer 11 Mode/function 12 Effect Product Overview 115/230V switch Power switch DMX out 3 & 5-pin Easy Controller Microphone DMX in 3 & 5-pin IEC Power input Intimidator™ Spot 150 User Manual 6 6/1
3. SETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. A HTI 150W discharge lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement. Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation.
Lamp Alignment How-To After a new installation of a lamp, you may find that there is an uneven field of light or what is refered to as a “hot spot”. This is due to the most intense point of the lamp source not being positioned optimally within the reflector. Lamp alignment screws There are 3 lamp alignment screws provided at the base of the fixture. Turning these screws allows you to optimize the projection quality of the spot, as well as the overall intensity of the beam. 1.
Replacing Gobos Top cover screws 1) Be sure the fixture is not powered or connected to mains. 2) Remove the top cover by removing the 4 screws with a Phillips #2 screwdriver. 3) With your hand, move the gobo wheel to the desired gobo to change. 4) You may now replace the gobo easily by removing 2 the retaining ring. This may be done with a small tool. 5) Replace the new gobo and the retaining ring. 6) Replace top cover and 4 cover screws.
Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. Important: Fixtures on a serial data link must be daisy chained in one single line.
3-PI N T O 5-PI N CO NVERSI O N CHART Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. CHAUVET Model No: DMX5M, or DMX5F.
Mounting O RI ENT AT I O N This fixture may be mounted in a hanging or floor mounted/upright position. Do not hang this fixture at odd angels, such as 45° degrees or 90° degrees! RI G G I NG Hanging Clamp It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O” type clamp (CLP-15, CLP-06. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs.
MAN U AL F O CUS This fixture has a manual focus mechanical adjustment. 1. 2. Locate the focus adjustment knob at the front of the fixture. Using your hand (not a tool!) rotate this either clockwise or counter-clockwise in the desired focus position. Note: you may not adjust this focus remotely, so be sure to set this to a position that works in the location that you are running/installing the fixture.
4. OPERATING INSTRUCTIONS Navigating the Control Panel Access control panel functions using the four panel buttons located directly underneath the LCD Display.
Menu Map M AIN FUNCTION SUB-FUNCTION SELECTION 1.
Menu Map (continued) Service Menu Map The password is: 2323 Exit this mode by pressing Mode/Esc 2 times (2X) Intimidator™ Spot 150 User Manual 16 6/19/2009 9:08 AM
User Configurations T O SET T HE PAN T O I N VERT I NG O R NO N -INVERT I NG : 1) Press the
T O REST O RE AL L SET T I NG S T O T HEI R F AC T O RY DEF AUL T S: Warning: This will erase all user settings and revert the fixture back to the original factory defaults! 1) Under the “11-Load Set”, Press . 2) “Select: Ok”. 3) Press the button Operation Stand-Alone Mode (Sound-Active, Auto Mode): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode.
DMX Channel Values Advance Mode: (16-bit pan/tilt, 12-channel) CHANNEL VALUE FUNCTION 000 255 Pan 0° 540° 000 255 Tilt 0° 270° 000 255 Pan fine 0° 3° 000 255 Tilt fine 0° 3° 000 255 Pan/tilt speed Fast Slow 000 007 008 015 016 023 024 031 032 039 040 047 048 055 056 063 064 066 067 078 079 092 093 107 108 120 121 136 137 152 153 170 171 212 213 255 Color Wheel White (open) Light Blue Red Peachblow Green Yellow Pink UV White White + Light
010 014 015 019 020 024 025 029 030 034 035 039 040 044 045 049 050 054 055 059 060 064 065 069 070 074 075 079 080 089 090 111 112 119 120 127 128 129 130 192 193 255 Pan/tilt move-in-black Pan/tilt move-in-black (disabled) Color wheel move-in-black Color wheel move-in-black (disabled) Gobo wheel move-in-black Gobo wheel move-in-black (disabled) All movement move-in-black All movement move-in-black (disabled) Reset pan/tilt Reset color wheel Reset gobo wheel Reset
Basic Mode: (8-bit pan/tilt, 8-channel) CHANNEL VALUE FUNCTION 1 000 255 Pan 0° 540° 2 000 255 Tilt 0° 270° 000 007 008 015 016 023 024 031 032 039 040 047 048 055 056 063 064 066 067 078 079 092 093 107 108 120 121 136 137 152 153 170 171 212 213 255 Color Wheel White (open) Light Blue Red Peachblow Green Yellow Pink UV White White + Light Blue Light Blue + Red Red + Peachblow Peachblow + Green Green + Yellow Yellow + Pink Pink + UV Rotating clockwise w
075 079 080 089 090 111 112 119 120 127 128 129 130 192 193 255 Reset prism Reset all No function Lamp off Lamp on No function Auto program Sound program 5. APPENDIX DMX Primer There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller.
Intimidator Spot 150 Service Maintenance Guide Symptom(s) Lamp is not illuminating Breaker/Fuse keeps blowing Device has no power Fixture is not responding to DMX Possible Solution(s) Clean the fixture regularly to avoid any such failure. This fixture is forced convection cooled, which means that if the fans are kept clean and free of debris, then proper cooling will be allowed to occur Check the options in the display for Lamp function [on~off]. Also check the DMX signal.
Contact Us Wo rl d Wi d e General Information CHAUVET th 3000 North 29 Court Hollywood, FL 33020 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084 Technical Support CHAUVET th 3000 North 29 Court Hollywood, FL 33020 voice: 954.929.1115 (Press 4) fax: 954.929.5560 (Attention: Service) World Wide Web www.chauvetlighting.com Website: http://www.chauvetlighting.
General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power.
Technical Specifications WEIGHT & DIMENSIONS Length .............................................................................................................................. 13.4 in (340 mm) Width ................................................................................................................................ 13.1 in (333 mm) Height ............................................................................................................................... 17.6 in (446 mm) Weight .....