User Manual

ManualsBrandsCheckline ManualsMeasuring instrumentsBLH

 Checkline-Europe

-16-

NOTE

 Checkline-Europe

-1-

TABLE OF CONTENTS

1.0 Design of the device ……………………………………………… 2

2.0 Measuring procedure ………………………………………………… 3

2.1 Information of the measurement of sawdust

3.0 Calibration curves ……………………………………………….. 6

4.0 Determination of the material reference moisture ……………….. 6

5.0 Menu level overview ………………………………………………..… 7

6.0 Changing batteries ………………………….……………………..… 8

7.0 Transfer saved data to the PC …………….……………………….. 9

8.0 Print saved data ……………………………………….………….… 10

9.0 Online print and online send ……………………………….…………….. 10

10.0 Device maintenance instructions …………………………………… 11

11.0 Exemption from liability …………………….……………………….. 11

12.0 Technical data ……………………………………….…………….…. 12

13.0 Most common reasons for miss readings …………………………. 13

14.0 Warranty ……………..………………….……………………………... 14

Summary of content (9 pages)

PAGE 1
NOTE TABLE OF CONTENTS 1.0 Design of the device ……………………………………………… 2 2.0 Measuring procedure ………………………………………………… 3 2.1 Information of the measurement of sawdust 3.0 Calibration curves ……………………………………………….. 4.0 Determination of the material reference moisture 5.0 Menu level overview 6.0 Changing batteries 7.0 Transfer saved data to the PC 8.0 Print saved data 9.0 Online print and online send ……………………………….…………….. 10 10.0 Device maintenance instructions …………………………………… 11 11.
PAGE 2
1.
PAGE 3
14.0 WARRANTY 2.0 Electromatic Equipment Co., Inc. (Electromatic) warrants to the original purchaser that this product is of merchantable quality and confirms in kind and quality with the descriptions and specifications thereof.
PAGE 4
6. Compress the material in the measuring chamber now by turning the hand wheel (1 turn per second) until the LED turns green. Now slowly (0.5 turns per second) must be rotated until the LED flashes orange once. LED off LED green 13.0 • LED orange MOST COMMON REASONS FOR MISS READINGS Product temperature out of application range Material below 0°C resp. above +40°C (32 to 104 °F) may cause faulty measurements.
PAGE 5
12.0 TECHNICAL DATA 2.1 Information of the measurement of sawdust Resolution of the display 0.5% water content 0.5°C temperature Measuring range 15 up to 65% depending on the material Operation temperature 0°C up to +40°C Storage temperature -20°C to +60°C Temperature compensation Automatically Power supply 4 pcs. 1.5 Volt AA Alkaline batteries (900 measurements) Auto Switch OFF After app.
PAGE 6
3.0 CALIBRATION CURVES Type of wood Beech Beech Birch Birch Oak Oak Spruce Spruce Poplar Poplar Reference 10.0 Filling quantity 50 g 100 g 50 g 100 g 50 g 100 g 50 g 100 g 50 g 100 g ------ Measuring range 15 % to 45% 40 % to 60 % 15 % to 45% 35 % to 55% 15% to 45% 40% to 55% 15% to 60% 50% to 65% 15% to 60% 50% to 60% ------ To verify the calibration curve only the standardized drying method is permissible because many other methods used are doubtful and can lead to incorrect comparison values.
PAGE 7
8.0 PRINT SAVED DATA 5.0 MENU LEVEL OVERVIEW Keypad symbols To print your saved data, connect the device to the printer using the printer cable that was delivered with your device. Carefully loose the protection cap on the humimeter BLH. At first plug in the side of the connector with the close plastic casing at the humimeter BLH. Then switch on the device.
PAGE 8
6.0 CHANGING BATTERIES 7.0 Please find enclosed the manual for changing of batteries: 1. Press with your finger onto the arrow of the battery cap and pull it back. TRANSFER SAVED DATA TO THE PC To send your saved logs to the PC, connect the humimeter device to your PC using the USB cable that was delivered with your device. Carefully loose the protection cap on your humimeter and plug in the USB mini B connector. The bigger connector has to be connected to a USB slot on your PC. 2.
PAGE 9
BLH WOOD SHAVINGS MOISTURE METER OPERATING INSTRUCTIONS