Owner's manual

ManualsBrandsCheckline ManualsMeasuring instrumentsBLL

 Electromatic Equipment Co., Inc.

-16-

NOTES

 Electromatic Equipment Co., Inc.

-1-

TABLE OF CONTENTS

1.0 Design of the device ………………………………………………… 2

2.0 Calibration curves …………………………………………………… 3

3.0 Determination of the material reference moisture ……………….. 3

4.0 Measuring procedure ……………………………………………….. 4

5.0 Menu level overview ………………………………………………… 5

6.0 Changing batteries ………………………………………………..… 6

7.0 List of calibration curves ………………………………………….… 6

8.0 Running the instrument …………………………………………….. 7

9.0 Activation of the “super user” function …………………………...… 8

10.0 Device maintenance instructions ………………………………..… 8

11.0 Transfer saved data to the PC ……………………………………… 9

12.0 Print saved data ………………………………………………….…. 10

13.0 Technical data ………………………………………………………. 11

14.0 Exemption from liability ……………………………………………... 11

15.0 Most common reasons for miss readings ………………………… 12

16.0 Warranty ……………………………………………………………… 13

Summary of content (9 pages)

PAGE 1
NOTES TABLE OF CONTENTS 1.0 Design of the device ………………………………………………… 2 2.0 Calibration curves …………………………………………………… 3 3.0 Determination of the material reference moisture 4.0 ……………….. 3 Measuring procedure ……………………………………………….. 4 5.0 Menu level overview ………………………………………………… 5 6.0 Changing batteries ………………………………………………..… 6 7.0 List of calibration curves ………………………………………….… 6 8.0 Running the instrument …………………………………………….. 7 9.0 Activation of the “super user” function 10.
PAGE 2
1.0 DESIGN OF THE DEVICE NOTES Measuring head Water content Insertion probe Temperature POWER button Batteries slot (flipside)  Electromatic Equipment Co., Inc.  Electromatic Equipment Co., Inc.
PAGE 3
NOTES 2.0 CALIBRATION CURVES Calibration curves Wood chips Coarse chips Industrial chips Test block Declaration Measuring range Standard wood chips 10 - 50% Coarse wood chips 10 - 50% Industrial wood chips 10 - 50% ! Only for testing the BLL with the test block ! • Wood chips: standard chips of wood (forest wood chips) according to EU-norm CEN/TS 14961 class P16 and P45. • Coarse chips: for coarse wood chips P45 but with fewer fines.
PAGE 4
.0 MEASURING PROCEDURE 16.0 1. For a correct measurement please ensure that the device has the same temperature than the wood chips (+/-3°C). For that reason, let your BLL adjust to the surrounding temperature of the material for at least half an hour before measuring. 2. Switch on the device: Press the key for 3 seconds. 3. Change the calibration curve: Press one time the key or key. The name of the calibration and then the curve can be seen at the head of the display. 4.
PAGE 5
15.0 • MOST COMMON REASONS FOR MISS READINGS 5.0 MENU LEVEL OVERVIEW Keypad symbols Product temperature out of application range Store menu Material below 0°C resp. above +40°C (32 to 104 °F) may cause faulty measurements. The storage of cold material in a warm storage area usually creates condensed water which may lead to major measuring errors. • Watch the saved data (logs) Save new value Power off (3 sec.
PAGE 6
.0 CHANGING BATTERIES 13.0 TECHNICAL DATA Resolution of the display 0.5% water content 0.5°C temperature Measuring range 10 to 50% water content Operation temperature 0°C up to +40°C 2. Remove the empty batteries. Storage temperature -20°C to +60°C 3. Put four new batteries in the device. Make sure that the positions of the battery poles are correct. Temperature compensation Automatically Power supply 4 pcs. 1.5 Volt AA Alkaline batteries (900 measurements) Auto Switch OFF After app.
PAGE 7
12.0 PRINT SAVED DATA 8.0 RUNNING THE INSTRUMENT (Only possible with USB interface module in combination with the Checkline thermo printer) Switch on: Press the Set the clock: Press 3 times the To print your saved data, connect the device to the printer using the printer cable that was delivered with your device. Carefully loose the protection cap on the BLL. At first plug in the side of the connector with the close plastic casing at the BLL. Then switch on the device.
PAGE 8
9.0 ACTIVATION OF THE “SUPER USER” FUNCTION 11.0 2 times - Options – Unlock Enter the 4-digit password by using the button (standard is the 4-digit serial number) and confirm by pressing the button. Changing the Userlevel Changing from advanced user to single user: Make sure that you have activated the “super user” functions according to the instructions above. Afterwards change to the menu and choose „Options“.
PAGE 9
BLL & BLL-USB WOOD CHIP MOISTURE METER OPERATING INSTRUCTIONS