Manual

ManualsBrandsCheckline ManualsMeasuring instrumentsCDT-2000HD

116

OI407G-2000

01.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02

1.1 Applications

02.0 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

03.0 Contents of Complete Outfit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

04.0 Overview of CDT-2000HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05

4.1 LCD Display

4.2 Front Panel Key Functions

05.0 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06

06.0 Measuring RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07

6.1 Contact Operation

6.2 Non-Contact Operation

07.0 Measuring Surface Speed or Length . . . . . . . . . . . . . . . . . . . . . . . . . . 09

08.0 Using Optional Surface Speed Wheels . . . . . . . . . . . . . . . . . . . . . . . . . 10

09.0 Memory System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

10.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

11.0 Spare Parts & Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

12.0 Removing the Protective Rubber Shell . . . . . . . . . . . . . . . . . . . . . . . . . 14

13.0 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table of Contents

NOTES

Summary of content (9 pages)

PAGE 1
OI407G-2000 NOTES Table of Contents 16 01.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02 1.1 Applications 02.0 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 03.0 Contents of Complete Outfit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 04.0 Overview of CDT-2000HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05 4.1 LCD Display 4.
PAGE 2
1.0 INTRODUCTION 13.0 Warranty The CDT-2000HD Digital Tachometer combines the best features of contact and non-contact tachometers for measuring rotational speed, surface speed and length. When used in the non-contact operating mode, a small piece of reflective tape is applied to the rotating element (wheel, shaft, etc.). The CDT-2000HD uses a visible LED light source to accurately measure the RPM from up to 24” (60 cm) away from the “target”.
PAGE 3
12.0 Removing Protective Rubber Shell The gauge is supplied with a durable rubber shell that provides an added measure of physical and environmental protection in harsh applications. To remove the shell, follow the procedure outlined below: 1. Using your thumbs, slide the rubber shell up and off of one corner of the gauge. Repeat for the other corner 2. Pull the shell down until it is completely off the corners of the gauge, the pull the gauge forward and out of the shell. 3.
PAGE 4
11.0 3.0 CONTENTS OF COMPLETE OUTFIT SPARE PARTS & OPTIONAL ACCESSORIES The CDT-2000 is supplied with the following accessories in a foam-fitted, carrying case: Standard Spare Parts 1. Meter with molded rubber shell 2. Slide-on Contact Adapter 3. 6" Circumference Surface Speed Wheel 4. Cone Tip Measuring Adapter 5. Reflective Tape (10 strips) 6. Two AA Batteries (not shown) 7. NIST Calibration Certificate (not shown) 8.
PAGE 5
10.0 SPECIFICATIONS 4.0 OVERVIEW OF CDT-2000HD Measuring Ranges – rpm Optical Mechanical 1 1 – 99,999 rpm 1 – 99,999 rpm 5 Measuring Ranges – speed Wheel Size m/min ft/min in/min m/sec ft/sec 6" 0.10–1524 0.40–5000 4.0–60.00 0.10–25.40 0.10–83.33 12" 0.40–609.6 0.40–2000 4.00–24.000 0.10–10.16 0.10–33.33 2 0.1 m 0.10–1999 0.40–6550 4.00–78.700 0.10–33.30 0.
PAGE 6
5.0 INSTALLING BATTERIES 9.0 MEMORY SYSTEM 1. Turn the gauge over and locate the battery compartment. You do not have to remove the rubber shell. The CDT-2000HD is supplied with a built-in memory system which stores the last measurement, maximum measurement, minimum measurement, and the average measurement which occurred during a measuring period. A measuring period is the interval of time while the Measure key is depressed.
PAGE 7
8.0 USING OPTIONAL-SIZED SURFACE SPEED WHEELS 6.0 MEASURING RPM 6.1 Contact Operation - RPM The following wheels can be used with the CDT-2000HD ax in m m em EM m in rp /m in m /m in ft /m in 3.8" (97mm) .8 .8.8 8.8 1.2" (32mm) M 1.9" (49mm) m 1. Install the Slide-on Contact Adapter. Push on securely M Optional 12" Wheel DE Optional 0.1 Meter Wheel O Standard 6" Wheel 2. Slide the Cone Tip adapter over the shaft of the instrument.
PAGE 8
6.2 Non-Contact Operation - RPM 7.0 MEASURING SURFACE SPEED OR LENGTH m ax m .8 .8.8 8.8 in m 1. Install the Slide-on Contact Adapter. em m m in rp /m in m /m in ft /m in EM M 1. Remove the Contact Adapter. ax m .8 .8.8 8.8 in m em m in rp /m in m /m in ft /m in EM M DE O M DE O M 2. Attach a small piece of the supplied reflective tape to the rotating element (shaft, pulley, etc.). 2. Slide the Surface Speed Wheel over the shaft of the instrument.
PAGE 9
CHECK•LINE BY ELECTROMATIC CDT-2000HD Digital Tachometer CHECK•LINE ® ELECTROMATIC E INSTRUMENTS Q U I P M E N T C O ., I N C . 600 Oakland Ave., Cedarhurst, NY 11516–U.S.A.