Manual

page 7page 14
Power-On programming
Turn on the gauge. Press and for 3 seconds to enter
Power-On programming (CF9 flashes with solid F0). Press or
to cycle CF9 F0, CF9 F1, CF9 F2, CF9 F3, CF9 F4, CF9 F5,
CF9 F6 and CF9 End. Press to select a function.
CF9 F0 Memory recall
Press SEND, memory location and value cycle. Press PEAK or ZERO to increase or
decrease memory number (and corresponding value).
CF9 F1 High & low setpoints Default=‘0’ both Hi and Lo
Press SEND, –HI– displays, then the high set value (i.e. H 10.0). Press PEAK to
increase and ZERO to decrease, press SEND to select. –LO– displays then the low set
value (i.e. L 5.0). Press PEAK to increase and ZERO to decrease, press SEND to select,
CF9 End displays. Press SEND again to exit.
CF9 F2 Peak mode Default=‘Or’
Press SEND, ‘Or’ or ‘And’ displays. Press PEAK or ZERO to cycle. Press SEND to
select. ‘Or Peak’ records the Peak in either compression or tension during test. ‘And
Peak’ records both the compression peak and tension peak during a test.
Zero reset memory store Default=‘AA-OFF’
Auto memory displays after Peak mode is selected. ‘AA-On’ enables automatic memory
storage and reset to zero. ‘AA-OFF’ turns off auto function. Press PEAK or ZERO to
change. Press SEND to select, CF9End displays, press SEND again to exit.
CF9 F3 Auto zero reset Default=‘Ac-OFF’
Press SEND, ‘Ac-On’ or ‘Ac-OFF’ displays. Press PEAK or ZERO to cycle. If ‘AC-On’ is
selected, auto zero reset duration can be programmed. Press PEAK to increase or
ZERO to decrease. Press SEND to select, CF9End displays, press SEND again to exit
(i.e. ‘SEC 3.0’ is displayed for auto zero reset duration of 3 seconds).
CF9 F4 Audible beep Default=‘Sd-On’
Press SEND, ‘Sd-On’ for alarm on, or ‘Sd-OFF’ for off displays. Press PEAK or ZERO to
cycle. Press SEND to select. CF9End displays, press SEND again to exit (alarm sounds
for values over HI or under LO setpoints).
Setpoint alarm Default=’’
Setpoint alarm displays after audible beep is selected. ‘AL-On’ for setpoint alarm on or
‘AL-OFF’ for off. Press PEAK or ZERO to cycle. Press SEND to select, CF9End displays,
press SEND again to exit.
CF9 F5 Reverse display
Press SEND, ‘-12345’ for standard or ’ ’ for reverse displays. Press PEAK or
ZERO to cycle. Press SEND to select. Flashing CF9 with solid End displays. Press
SEND again to exit. (for vertical mounting).
CF9 F6 Auto power off duration Default=‘AO-10’
Press SEND, ‘AO-10’ displays. Press PEAK or ZERO to cycle ‘AO-5’ for 5 min auto
power off duration, ‘AO-10’ for 10 min, ‘AO-30’ for 30 min, ‘AO-60’ for 60 min and ‘AO-
OFF’ to by-pass auto power off. Press SEND to select, CF9End displays, press SEND
again to exit.
-12345
Downloading Data from Memory
Choose between the following download methods.
RS-232C Data Download from Memory
Connect the gauge and device receiving data with a CB-204
cable. Use the I[CR] ASCII command to transmit data (uppercase
ASCII character format).
USB Data Download from Memory
Use ZP Logger software to downoad data from memory using
USB, see pages 16-19.
Clearing Data from Memory
1. Turn off the gauge.
2. Press again while holding to enter memory mode.
Single Memory Clear
A memory location number that is displayed with a dot at both
ends is the last stored data and is the only one that can be erased.
Press to erase and ErASEd is displayed. If you attempt to erase
any other memory location Error is displayed. If all data is erased,
– – – – – is displayed then flashing CF9 with solid End. Continue
Power-On programming or press to exit (See page 18).
All Memory Clear
While a memory value and location are displayed, press for 3
seconds, all data is erased and ErASEd is displayed, then – – – – –.
Continue Power-On programming or press to exit.
Recalling Data from Memory
1. Turn on the gauge.
2. Press and for 3 seconds to enter Power-On program-
ming (CF9 flashes with solid F0). Press and the display
cycles memory location and value. Press to increase loca-
tion and to decrease. Press to exit.