User Manual FABX1A-LE & FABX2A-LE The models detailed within this document comply with ANSI Z359.14-2014, ANSI A10.32:2012, OSHA 1910 and OSHA 1926 Subpart M Requirements.
User Manual Page 2 FABX1A-LE & FABX2A-LE Index Page 1.0 Warnings! & Model Designation 3 2.0 Installation & Anchorage 4 3.0 Use 5 4.0 Compatibility 6 5.0 Fall Clearance 7 6.0 Issue, Inspection, Storage & Rescue Planning 8 7.0 Labels 9 8.0 Quality, Legislation & Exclusions 10 9.0 Record Card 11-12 CAUTION! Working at height is dangerous. This product is designed to reduce the risk of working at height, by providing protection in the event of a fall to reduce the risk of injury.
User Manual Page 3 FABX1A-LE & FABX2A-LE SECTION 1.0 Warnings! & Model Designation WARNINGS! These instructions, including safe usage, warnings, and limitation of the products, must be provided to the user, and they must be read before any inspection, installation or use of this product. If there are any points in this manual that you are unsure of, seek a competent, trained person to clarify before using.
User Manual Page 4 FABX1A-LE & FABX2A-LE Installation & Anchorage SECTION 2.0 Installation and Anchorage: The SRL-LE must be anchored to a point which will hold a load of 5000lbs or meet OSHA requirements for twice the anticipated load (certified by a qualified person) and that is fixed, preventing the device anchorage from moving while in use. The SRL must be connected to the anchorage using a suitable approved connector. Install the SRL so that it avoids swing hazards.
User Manual Page 5 FABX1A-LE & FABX2A-LE Use SECTION 3.0 Personal Fall Arrest: The SRL-LE may be used to support a MAXIMUM 1 Personal Fall Arrest System (PFAS) for use in Fall Arrest applications. Structure must withstand loads applied in the directions permitted by the system of at least 5,000 lbs. Freefall limit: 2ft . Applicable D-ring: Dorsal. Restraint: The SRL-LE may be used in Restraint applications. Restraint systems prevent workers from reaching the leading edge of a fall hazard.
User Manual Page 6 FABX1A-LE & FABX2A-LE SECTION 4.0 Compatibility Compatibility: When making connections with Checkmate SRLs, eliminate all possibility of roll-out. Roll-out occurs when interference between a hook and the attachment point causes the hook gate to unintentionally open and release. All connections must be selected and deemed compatible with Xcalibre SRL by a Competent Person. All connector gates must be self-closing and self-locking, and withstand minimum loads of 3,600lbs.
User Manual Page 7 FABX1A-LE & FABX2A-LE Fall Clearance Fall Clearance *Eliminate Swing Fall whenever possible! If swing fall exists, always account for additional fall clearance. SECTION 5.
User Manual Page 8 FABX1A-LE & FABX2A-LE Issue, Inspection, Storage & Rescue Planning SECTION 6.0 Issue: This and associated equipment must be visually inspected by a competent person when initially delivered to site, thereafter the product must be inspected before and after use. A record card is printed in this manual, and should be updated after each routine inspection. Follow the points laid down in the section headed “Inspection” without deviation.
A4 DO NOTCOMPLIES SCALE THIS DRAWINGA4 COMPLIES WITH BS.8888 THIS DRAWING WITH BS.8888 DWG NO.PPELAB-85 DO NOT SCALE User Manual Page 9 FABX1A-LE & FABX2A-LE SECTION 7.0 Labels48 48 FABX1-LE Self-Retracting Lifeline Part # Lot # WARNING: Prior to use, fully read and understand all manufacturer’s instructions provided with equipment at time of shipment. USE: This device is only for use by one person as a fall arrester. Only make connections directly to attachment point on safety harness.
User Manual Page 10 FABX1A-LE & FABX2A-LE SECTION 8.0 Quality, Legislation & Exclusions 4.1 Quality 4.3 Exclusions All Checkmate products are manufactured under ISO 9001 and to the highest standards. The scope of use within the certification held allows Checkmate to design, manufacture and test Personal Protection Equipment. Horizontal tensile test machine, abrasion tester and dynamic drop test rig are just part of the full range of test facilities used to ensure ultimate safety of our product range.
User Manual Page 11 FABX1A-LE & FABX2A-LE Record Card Section 9.
85384 (Rev.A) User Manual Page 12 FABX1A-LE & FABX2A-LE Record Card Section 9.0 SERIAL NO: DATE: PRODUCT CODE: USER: DATE CONDITION OF SYSTEM INSPECTED BY Approved service company: Checkmate Lifting & Safety LTD, Sheerness, Kent. England. ME12 1PZ, UK Tel: 1-800-466-6385 www.checkmateuk.
