Classic IP Style SSB Installation Manual Version *60 P/N 10039422
Classic IP Style SSB Installation Manual Copyright © 2011 by Checkpoint Systems Inc. Released 03/16/2012. Published by: Checkpoint Systems Inc. 101 Wolf Drive Thorofare, NJ 08086 Document revision information Classic IP Style SSB Installation Manual, version *60 Rev Description Date Author *60 CR2637A 03/16/2012 Andy Mei, Chris Zheng Trademarks Checkpoint is a registered trademark of Checkpoint Systems, Inc.
Important Information to our Users in North America FCC Regulatory Compliance Statement Checkpoint Systems, Inc., offers Electronic Article Surveillance (EAS) or Radio Frequency Identification Products that have been FCC certified or verified to 47 CFR Part 15 Subparts B/C and/or 47 CFR Part 18. Appropriately, one f the following labels will apply to the approval: NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
Industrie Canada Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.
Important Information to our Users in Europe CE Regulatory Compliance Statement Where applicable, Checkpoint Systems, Inc., offers certain Electronic Article Surveillance (EAS) products that have CE Declarations of Conformity according to R&TTE Directive 99/5/EC.
Table of Contents TABLE OF CONTENTS .................................................................................................................................................6 INSTALLATION OVERVIEW .................................................................................................................................8 OVERVIEW .................................................................................................................................................................
CHAPTER 1 INTRODUCTION This Installation Manual details the steps necessary for the proper installation and configuration of the Classic IP Style SSB systems. In this manual, most illustrations and pictures will show the Style Facelift as a place of reference, but it is to be understood that each antenna would be installed in the same manner (unless otherwise noted).
CHAPTER 2 I N S T A L L A T I O N O V E R V IE W Overview This chapter is an overview of the installation process: 1. Requirements: Tool and part requirements for a typical installation. 2. Installation Outline: Lists the basic installation steps in sequence.
application developed to install and configure TR4210 boards via serial connections. DMS provides for firmware updates without replacement of microchips. Parts Quantity will vary according to site. 18 AWG 2-conductor (STP) CAT5e cable 22 AWG 4-conductor (STP) (5594) 1/2” Anchor Bolts *DekDuct (wire chase) *Wiremold (1500 or 2600 series) *Wiremold anchor bolts Note: *Wire routing methods will vary by installation.
CHAPTER 3 PHYSICAL INSTALLATION Overview This chapter covers the physical placement and installation of the TR4210 antennas and power supply in the following sections: 1. Placement: How to determine the proper placement of the antennas. 2. Power Supply: Information on typical power supply placement. 3. Wire Routing: Information on typical wire routing methods. 4. Antenna Mounting: Antenna mounting information. Note: For details of placement, refer to Evolve installation manual, CKP P/N 7994249.
If mounted in a plenum space, proper plenum rated wiring and plenum rated enclosures are required. The maximum operation temperature should be no more than 40 . ℃ Note: For more information about power supplies, please see “Power Supplies” on Appendix 2. Antenna Mounting Antennas are typically not mounted until after the finished flooring is in place. Mounting Hardware For mounting on Concrete Floor Utilize two (2) 1.3cm [.5in.] anchor bolts per antenna.
Wire Routing Methods of Wire Routing Floor Trench: Typically 1.3cm [.5in.] wide by 3.8cm [1.5in.], but an increase in dimensions is recommended for more than two antennas. Wiremold: 1500 or 2600 series wire mold can be utilized. Typically wire mold is not used within customer traffic areas, so a typical placement is from the outside of the antennas to the doorframe. Conduit: 2.5cm [1in.] diameter conduit can be utilized in new construction situations.
CHAPTER 4 ANTENNA WIRING Overview This chapter describes the Classic IP Style SSB antennas wiring and cabling. WARNING: This system runs on TR4210† electronics with firmware version 3.61 or higher. It is critical to note that ONLY TR4210 electronics can be used in conjunction with this system. It is also critical that DMS version 1.8.31 or later be used to configure the system. Information is covered in the following sections: 1. General wiring instruction 2.
Figure 4 TR4210 Reader Board Balance 2-loop Balance 3-loop Figure 5 Passive Coupler Board Classic IP Style SSB Installation Manual Rev.
Wiring between Chassis Box /SSB There are only two (2) wires connected Chassis and SSB. They are 1) RG59 coax cable and 2) SSB Light/Sounder cable (22 AWG 4-conductors (STP) (5594)/2-conductors 22 AWG B 8442 RG59 Coax Cable: A 26ft long, two end pre-terminated RG59 coaxial cable is packed with SSB antenna. It connects the Chassis Box antenna (SSB). It is recommended to leave the one pre-terminated end with 3-pin Connector at the SSB, another pre-terminated shield end to Chassis Box.
Secondary SSB Light/Sounder Cable Wiring Table 4 conductor wire WHITE J42-LTS+ Classic IP Style SSB 2 LT Blue GREEN J41-LTS+ LT Red RED BLACK J18 Power + J18 Power - LT Power + LT Power - Wire Color Chassis Box 2 conductor wire RED J54 SND 2+ SD + BLACK J54 SND 2- SD - Table 1 SSB Light/Sounder Cable Wiring Table Wiring 24VDC power supply A Checkpoint certified 24VDC power supply can power up to Chassis Box.
Figure 8 24 VDC power filter Single Aisle Wiring The single aisle installation is the most common Classic IP Style SSB application which best utilizes the SSB-SSB configuration (see Figure 9 Single Aisle). A typical single aisle installation consists of a Chassis Box, two secondary antennas (SSB), a power supply and a cable kit (packaged with secondary antenna). It is recommended to start SSB wiring first, then connect Chassis Box. Connect the power cable last.
Note: It is recommended to leave the pre-terminated coax cable end at SSB location where the cable was laid out. Step 3: Connect the SSB Lights/Sounder cable to 6 pin connector as Figure11 shown, colorful line show the cable that need on site assemble by field servers engineering team . Step 4: Inspect wiring and connections, confirm coupler board jumper settings (see Figure 10 SSB Coupler Board Jumper Settings). Step 5: Put the base cover back and secure.
Figure 11 Classic IP Style SSB Antenna Wiring Chassis Box wiring Step 1: Step 2: Step 3: Step 4: Open the base cover(s). Cut, strip and terminate the RG59 coax cable, then plug it to the TR4210 board. Connect the SSB1 Lights/Sounder Cable wires to the electronic reader board (TR4210). Connect the SSB2 Lights/Sounder Cable wires to the electronic reader board (TR4210).
Figure 12 Chassis Box wiring Classic IP Style SSB Installation Manual Rev.
Power cable The R59 cable to SSB 2 Conductor wiring for sounder 4 conductor wiring for dual color light Figure 13 Coax cable and 4/2 conductor wiring connection Classic IP Style SSB Installation Manual Rev.
CHAPTER 5 E L E C T R O N I C S S E TT I N G Overview All electronics setting here aimed for on site configurations based on compliance and performance test result, if it still can not illuminate fundamental noise; please refer to tuning procedure of TR4210.
List of Ferrites for Classic IP Style SSB Classic IP Style SSB CKP P/N MFR MFR & MFR P/N # Turn s Cable installed on Install location Qty 221412 Fair Rite FAIR RITE 2861000202 1 2Loop cable Close to coupler board 2 221412 Fair Rite FAIR RITE 2861000202 1 3Loop cable Close to coupler board 2 7784420 Wurth WURTH 74271111 1 RG-59 COAX cable (both ends) exit point of cable from coupler 2 284760 Fair Rite FAIR RITE 0443806406 3 LED cable close to 6-pin connector 1 221412 Fair
APPENDIX 1 ANTENNA DIMENSIONS Classic IP Style SSB The weight of the antenna is 15.3kg, The weight of Chassis Box is 3kg. The antenna dimension as following Classic IP Style SSB Installation Manual Rev.
APPENDIX 2 P O W E R S U P P L IE S Overview This appendix covers all available (US and EU) TR4210 Style compatible power supplies. Details Power supplies have an output of +24 VDC. Requirements In the US, if the power supply is to be installed in a plenum (HVAC ventilation) area, the Globtek GS-599ES(R) and the Globtek GS-599MC-KIT(R) must be installed.
2. EOS- LFEVC65NS24PL (PN: 10102495) Note: Dimensions Width: 5.8 cm [2.284in] Length: 13.3 cm [5.236in] Height: 2.9 cm [1.152in] Weight 350 grams (12.35 ounces) Classic IP Style SSB Installation Manual Rev.
Power Supply Used In Europe Model The EU market uses one power supply types: EOS LFZVC36FS24S91 (PN: 7683707) Dimensions Length: 8.89cm [3.50in] Width: 2.42cm [0.95in] Height: 4.47cm [1.75in] Classic IP Style SSB Installation Manual Rev.
