Classic Style Installation Manual Version *60 P/N 10094144
Classic Style Installation Manual Copyright © 2011 by Checkpoint Systems Inc. Released XX/XX/2013. Published by: Checkpoint Systems Inc. 101 Wolf Drive Thorofare, NJ 08086 Document revision information Classic Style Installation Manual, version *60 Rev Description *60 CR2637C Date 1/9/2013 Author Ander Jiang, Chris Zheng Trademarks Checkpoint is a registered trademark of Checkpoint Systems, Inc. Checkpoint, Liberty, Evolve, and VisiPlus are registered trademarks of Checkpoint Systems, Inc.
Important Information to our Users in North America FCC Regulatory Compliance Statement Checkpoint Systems, Inc., offers Electronic Article Surveillance (EAS) or Radio Frequency Identification Products that have been FCC certified or verified to 47 CFR Part 15 Subparts B/C and/or 47 CFR Part 18. Appropriately, one of the following labels will apply to the approval: NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
Industry Canada Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
2. cet appareil doit supporter toute perturbation, y compris les perturbations qui pourraient provoquer son dysfonctionnement. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisis de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas celle nécessaire pour une communication réussie.
Important Information to our Users in Europe CE Regulatory Compliance Statement Where applicable, Checkpoint Systems, Inc., offers certain Electronic Article Surveillance (EAS) products that have CE Declarations of Conformity according to R&TTE Directive 99/5/EC.
Table of Contents TABLE OF CONTENTS ................................................................................................................... 7 INSTALLATION OVERVIEW .................................................................................................. 9 OVERVIEW ................................................................................................................................... 9 REQUIREMENTS................................................................................
CHAPTER 1 INTRODUCTION This Installation Manual details the steps necessary for the proper installation and configuration of the Classic Style systems. In this manual, most illustrations and pictures will show the Classic Style as a place of reference, but it is to be understood that each antenna would be installed in the same manner (unless otherwise noted). Classic Style front view Classic Style Side view Figure 1 Classic Style antenna front and side view Classic Style Installation Manual Rev.
CHAPTER 2 I N S T AL L AT IO N O V E R V IE W Overview This chapter is an overview of the installation process: 1. Requirements: Tool and part requirements for a typical installation. 2. Installation Outline: Lists the basic installation steps in sequence.
application developed to install and configure TR4215 boards via serial connections. DMS provides for firmware updates without replacement of microchips. Parts Quantity will vary according to site. 18 AWG 2-conductor (STP) CAT5e cable 22 AWG 4-conductor (STP) (5594) 1/2” Anchor Bolts *DekDuct (wire chase) *Wiremold (1500 or 2600 series) *Wiremold anchor bolts Note: *Wire routing methods will vary by installation.
CHAPTER 3 P H Y S IC A L I N S T A LL A T I O N Overview This chapter covers the physical placement and installation of the TR4215 antennas and power supply in the following sections: 1. Placement: How to determine the proper placement of the antennas. 2. Power Supply: Information on typical power supply placement. 3. Wire Routing: Information on typical wire routing methods. 4. Antenna Mounting: Antenna mounting information.
If mounted in a plenum space, proper plenum rated wiring and plenum rated enclosures are required. Note: For more information about power supplies, please see “Power Supplies” on Appendix 2. Antenna Mounting Antennas are typically not mounted until after the finished flooring is in place. Mounting Hardware For mounting on Concrete Floor Utilize two (2) 1.3cm [.5in.] anchor bolts per antenna. Figure 2 Anchor Bolt (Concrete Mounting) Wood Floor Utilize two (2) 1.3cm [.5in] lag bolts per antenna.
Wire Routing Methods of Wire Routing The cabling between PSB and SSB has to be routed either under floor or through floor wiremold. “Up & Over” routing method is not permitted for cabling between PSB and SSB. Correct Wire Incorrect Wire OR (A (B Figure 4 Methods of Wire Routing Floor Trench: Typically 1.3cm [.5in.] wide by 3.8cm [1.5in.], but an increase in dimensions is recommended for more than two antennas. Wiremold: 1500 or 2600 series wire mold can be utilized.
CHAPTER 4 A N T E NN A W IR I N G Overview This chapter describes the Classic Style with Coupler primary (PSB) and secondary (SSB) antennas wiring and cabling. WARNING: This system runs on TR4215† electronics with firmware version 4.00 or higher. It is critical to note that ONLY TR4215 electronics can be used in conjunction with this system. It is also critical that DMS version 1.8.31 or later be used to configure the system. Information is covered in the following sections: 1.
PAB SAB Sounder Sounder Metal PAB Point Lights Sync Out Sync In TX2 TX1 Badge Board Input Power SAB Lights Alarm Relay Optional 3rd TX Interface Figure 5 TR4215 Reader Board Figure 6 Passive Coupler Board Classic Style Installation Manual Rev.
Wiring between PSB/SSB There are only three wires connected between PSB and SSB. They are 1) RG59 coax cable and 2) SSB Dual color LED cable (22 AWG 4-conductors P/N 7102900 (STP) (5594)) 3) SSB Sounder cable 2-condutior wire(7045353) RG59 Coax Cable: A 13ft long, Two end pre-terminated RG59 coaxial cable is packed with SSB antenna. It connects the coupler boards (J5) in the primary antenna (PSB) and in the secondary antenna (SSB). 1.
Wiring 24VDC power supply A Checkpoint certified 24VDC power supply can power up to two (2) PSBs. It is recommended to wire the 24VDC power suppler to the nearer PSB filter board input, then, connect wire from this PSB’s filter board to J18 connector on the reader. The other output from the filter board could be wired to other PSB filter board input. (See Figure 10 24 VDC power filter). 24VDC power cable uses AWG18 two (2) conductor cable.
Single Aisle Wiring The single aisle installation is the most common Classic Style application which best utilizes the PSB-SSB configuration (see Figure 11 Single Aisle). A typical single aisle installation consists of a Style primary antenna (PSB), a secondary antenna (SSB), a power supply and a cable kit (packaged with secondary antenna). It is recommended to start SSB wiring first, then wire the PSB. Connect the power cable last.
Figure 12 SSB Coupler Board Jumper Settings Figure 13 Classic Style SSB Antenna Wiring Classic Style Installation Manual Rev.
Primary antenna (PSB) wiring Step 1: Open the base cover(s). Step 2: Connect the RG59 coax cable to J5 of coupler board,. Check the coupler board jumper settings (see igure 14 PSB Coupler Board Jumper Settings). Step 3: Connect the SSB dual color LED Cable wires for the Red/Blue lights to the J41/J42 on the electronic reader board (TR4215), connect dual color LED cable wire for power supply to filter board output. Step 4: Connect the SSB Sounder Cable wires to J54 on the electronic reader board (TR4215).
Figure 15 Classic Style PSB Antenna Wiring Classic Style Installation Manual Rev.
CHAPTER 5 E L E C T R ON IC S S E T T I N G Overview All electronics setting here aimed for on site configurations based on compliance and performance test result, If it sill can not illuminate fundamental noise, please refer to tuning procedure of TR4215 .
List of Ferrites for Classic Style Classic Style PSB CKP P/N MFR MFR & MFR P/N # Turns Cable installed on RG-59 COAX cable (both ends) install location Liberty Coupler A1096 7784420 Wurth WURTH 74271111 1 7284760 Fair Rite FAIR RITE 0443806406 4 Pwr supply - dc cable next to dc line filter pcb 1 Fair Rite FAIR RITE 0443806406 4 LED+sounder cable Next to terminal port of sounder and LED 7284760 1 617944 Fair-Rite FAIR RITE 2843006802 1 LED cable to port J42 next to TR4215 / port
APPENDIX 1 A N T E NN A D I M E NS IO N S Classic Style PSB/SSB Classic Style Installation Manual Rev.
APPENDIX 2 P O W E R S U P P L IE S Overview This appendix covers all available (US and EU) TR4215 Style compatible power supplies. Details Power supplies have an output of +24 VDC. Requirements In the US, if the power supply is to be installed in a plenum (HVAC ventilation) area, the Globtek GS-599ES(R) and the Globtek GS-599MC-KIT(R) must be installed.
2. EOS- LFEVC65NS24PL (PN: 10102495) Note: Dimensions Width: 5.8 cm [2.284in] Length: 13.3 cm [5.236in] Height: 2.9 cm [1.152in] Weight 350 grams (12.35 ounces) Classic Style Installation Manual Rev.
Power Supply Used In Europe Model The EU market uses one power supply types: EOS LFZVC36FS24S91 (PN: 7683707) Dimensions Length: 8.89cm [3.50in] Width: 2.42cm [0.95in] Height: 4.47cm [1.75in] Classic Style Installation Manual Rev.
