Specifications

Antenna Placement – FCC Region
With standard 410 EP series EAS tags, the maximum on-center aisle
width is 182cm [72 in] between antennas.
Dual A
isle (3 pedestal) and Multi-Aisle Layouts are applicable for wider exits.
The minimum distance between any door frame and antenna is 45.72cm [18 in].
Antenna Installation – Physical Requirements
Mounting:
Each antenna is mounted to the floor with two (2) anchor bolts.
Concrete: 1.3cm [0.5 in.] anchor bolts
Wood: 9.5mm [0.375 in.] lag bolts
Antennas are typically mounted by Checkpoint Field Service personnel.
Wiring Routing Methods:
Floor:
• Conduit Size: 4cm [1.5 in.] diameter – route between each antenna
(ensure conduit access under frame) and to power supply location.
• Placement Constraints: Conduit must be placed 68.5cm [27in] or further
back from the door frame.
The customer is typically responsible for conduit installation.
• Trench Dimensions: 9mm [0.375in] wide X 44mm [1.75in] deep
Floor trenching can be performed by the customer or by authorized Checkpoint personnel.
Vertical:
• Conduit: 4cm [1.5 in.] diameter – route from the floor level to the
power supply location (typically above the ceiling line, in the soffit)
The customer is typically responsible for vertical conduit installation (work with GC at site).
• In wall/mullion: Provide pull strings from the floor level to the ceiling level.
Wiring is pulled through hollow wall or mullion. See PSU Requirements.
The customer is typically responsible for providing
pull strings (at new construction or remodel sites)
Cable Requirements
Power Cable: 12 AWG 2-conductor for 12 VDC (RFID); see maximum length details.
18 AWG 2-conductor for 24 VDC (RF); no. of lengths depends on aisle and system.
Network: CAT 5e Ethernet Cable (standard network patch cable)
RF-EAS LTS/SND cable for Primary – Secondary layout (PSB –SSB config)
RF Sync and inter-pedestal connection: 8-conductor Modular cable
RF Coax for RF-EAS primary to secondary layout (PAB/SAB wiring
RFID Antennas: RG316 coax cable, 2 x 3m lengths for every aisle
Wiring is provided and typically installed by Checkpoint Installers
EVOLVE E10 2.0 RFID-Ready (RF) and RFID-enabled systems
Checkpoint Systems, Inc.
101 Wolf Drive
Thorofare, NJ 08086
1-800-257-5540
This drawing and the
accompanying written materials
are the exclusive property of
Checkpoint. Possession of this
document or any written
materials does not convey any
right to reproduce, disclose its
contents, or to produce, use or
sell anything it may describe.
Reproduction, disclosure or
use without specific prior
written authorization of
Checkpoint is strictly forbidden.
Any deviation to these
specifications must be
approved by project
management. Contact your
Checkpoint representative.
Specifications for
EVOLVE Exclusive E10 2.0
Systems (all models)
Last Revised: May 22, 2015
Content
: Physical Dimensions,
System Description (pg. 1 of 3)
This device is certified for mobile applications in which the antennas used
for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons.
Ferrite cores:
1) Fair Rite P/N 73420 (Order No. 2865-000-202): 1 on each Light and
Buzzer cable with 2 turns through the ferrite.
2) Würth 742 71111: 1 ferrite on the RX/TX cable with one turn through the
ferrite.
3) Würth 7427122, KITAGAWA SFC-10, Fair Rite P/N 284760 (Order No.
0443806406) or GRFC-10: 1 ferrite on DC cable of the power supply with
three turns through the ferrite.