E10 2.
E10 2.0 Quick Start Guide, Dual RF/RFID Pedestals Copyright © 2015 by Checkpoint Systems, Inc. All rights reserved. Checkpoint® is a registered trademark of Checkpoint Systems, Inc. Released May 20, 2015. Published by: Checkpoint Systems, Inc. 101 Wolf Drive Thorofare, NJ 08086 For use with Checkpoint’s E10 2.0 family of products. CHECKPOINT, COUNTERPOINT, EVOLVE AND VISIPLUS are registered trademarks of Checkpoint Systems, Inc. All other product or service names are the property of their respective owners.
Quick Start Guide: E10 2.0 RF/RFID Pedestals Installation Requirements Minimum Required Hardware (2) E10 2.0 Pedestals (for example, Single Aisle uses 1 A/N PSB and 1 P/N SSB units with the following) (1) E10 Interpedestal Cable kit (CKP P/N 10083615) (1) +24V DC Power Supply for RF-EAS readers (1) +12V DC Power Supply for RFID readers Note: All hardware items above must be ordered separately.
Checkpoint Systems, Inc. – Field Service Installation Document – CKP P/N ####### Main System I/O and UHF Ports for TX/RX Antenna 1 RFID Coax Connector Side (“top”) 2 “Side Panel” with 4-Pin Digital Input, Serial Port via RJ-45 and LTS/SND (covered in the GPIO section) 3 Ethernet Port - see Client Network connection 4 IN - Interped communication 5 OUT - Interped communication 6 +12V DC Power Input conn.
Quick Start Guide: E10 2.0 RF/RFID Pedestals Supported Configurations 1.1 Single Aisle (AN-PN) 1. Use interpedestal coax cable to connect RX3 of AN to RX5 of PN. 2. Use interpedestal coax cable to connect RX4 of AN to RX6 of PN. 3. Use interpedestal network cable to connect “Interpedestal OUT” of AN to “Interpedestal IN” of PN. 4. Connect 12 VDC to the WRTZ reader using power supply system. Figure 1: Pedestal / Array Layout: Standard Single Aisle 1.
Checkpoint Systems, Inc. – Field Service Installation Document – CKP P/N ####### 8. Use interpedestal network cable to connect “Interpedestal OUT” of AP to “Interpedestal IN” of next AP. 9. Use interpedestal network cable to connect “Interpedestal OUT” of next AP to “Interpedestal IN” of PN. 10. Connect 12 VDC to the WRTZ reader using power supply system. Wiring of Interpedestal Network Chain This connection diagram applies for all E10 2.
Quick Start Guide: E10 2.0 RF/RFID Pedestals 2.1.2 One Reader for Two Aisles (Dual-Aisle) Figure 5: AP configured for 2 Full Aisles (1R2A layout) 1. 2. 3. 4. 5. 6. 7. Use interpedestal coax cable to connect RX3 of AA to RX5 of first PN. Use interpedestal coax cable to connect RX4 of AA to RX6 of first PN. Use interpedestal coax cable to connect RX7 of AA to RX5 of second PN. Use interpedestal coax cable to connect RX8 of AA to RX6 of second PN.
Checkpoint Systems, Inc. – Field Service Installation Document – CKP P/N ####### 2.2.2 Two Readers Four Aisles (2R4A) Figure 7: 2 AP Pedestals configured for widest application “2R4A” - 2 readers driving 4 aisles This layout requires 2 AP pedestals/kits, and then 2 PNs (either can be removed for a half aisle on that side), as well as 1 PP in the center aisle position. 4 Full Aisles are covered.
Quick Start Guide: E10 2.0 RF/RFID Pedestals Complete Wiring The detailed procedure below has floor cut and ferrite core installation details that apply to all E10 2.0 installations. For RF-EAS system setup, refer to the Evolve manual (CKP P/N 7994249) or Quick Start Guide (CKP P/N 10077599). Procedure 1. Make the aisle floor cuts to accept all cables for Dual RF/RFID system.
Checkpoint Systems, Inc. – Field Service Installation Document – CKP P/N ####### 3. From this pedestal’s reader, connect from the Interped OUT Port using an interpedestal network cable (shielded Cat 5e from RFID installation/cable kit (cable is CKP P/N 7206088 - and the kit is CKP P/N 10083615). Apply a 10cm ferrite core with 2 turns. 4. Route Cat5 and coax cables to next pedestal (if not already).
Quick Start Guide: E10 2.0 RF/RFID Pedestals RFID Commissioning / UHF Antenna Tuning This procedure requires RFID-EAS tool (see Required tools). An overview is provided below. • Launch DMS. • Tune system for RF-EAS (connect to Evolve Board). • Confirm default profile for RFID Reader(s). Apply Region and if applicable, set the Application Mode to “Dual Aisle.” • Perform RX Map and EPC Positioning setup for Left and Right aisles. • Proceed with DMS to confirm detection.
Appendix A: Regulatory and Safety Important Information for our Users in North America FCC Regulatory Compliance Statement Checkpoint Systems, Inc., offers Electronic Article Surveillance (EAS) or Radio Frequency Identification Products that have been FCC certified or verified to 47 CFR Part 15 Subparts B/C.
Important Information to our Users in Europe CE Regulatory Compliance Statement Where applicable, Checkpoint Systems, Inc. offers certain Electronic Article Surveillance (EAS) products that have CE Declarations of Conformity according to R&TTE Directive 99/5/EC, EMC Directive 2004/108/EC, and Low Voltage Directive 2006/95/EC.
WEEE Marking All products that are subject to the WEEE Directive supplied by Checkpoint are compliant with the WEEE marking requirements. Such products are marked with the "crossed out wheelie bin" WEEE symbol shown below in accordance with European Standard EN 50419. Information for Users According to the requirements of European Union member state WEEE legislation, the following user information is provided in English for all Checkpoint supplied products subject to the WEEE directive.
