Cut Sheet

ManualsBrandsChemlink ManualsAdhesive SealantBlack M-1 Polyether Adhesive Sealant - 10oz Cartridge

Technical Data Guide Polyether Technology CSI Section No. 07 92 13

CHEM LINK Brands

Telephone: 800-826-1681

Fax: 269-679-4448

353 E Lyon Street

Schoolcraft, MI 49087

www.chemlink.com

Product Description

M-1

is a moisture curing, polyether adhesive

sealant designed for applications in damp, dry, or

cold climates. M-1

is solvent free and contains

no isocyanates.

M-1

will not shrink upon curing,

will not discolor when exposed to UV light, and

can not “out-gas”, or bubble on damp surfaces as

urethane sealants often do. M-1

is capable of joint

movement in excess of 25% in both compression

and extension. M-1

can be used effectively in many

difficult construction site conditions such as wet or dry

climates and at temperatures as low as 32°F (0°C).

Applicable Performance Standards

• ASTM C920, Type S, Grade NS, Class 25

Uses NT, T

, M, G, A & O

• Federal Specication TT-S-00230-C Type II, Class B

• Corps of Engineers CRD-C-541, Type II, Class B

• Canadian Standards Board CAN 19, 13-M82

Regulatory Compliance

• Conforms to OTC Rule for Sealants and Caulks

• Meets requirements of California Regs:

CARB, BAAQMD and SCAQMD

• Conforms to California Proposition 65

• Conforms to USDA Requirements for Non-food Contact

Green Standards:

• LEED 2.2 for New Construction and Major Renovations:

Low Emitting Materials (Section 4.1) 1 Point

• NAHB Model Green Home Building Guidelines:

5 Global Impact Points

• VOC Content: less than 20 grams / liter ASTM D2369

EPA Method 24 (tested at 240°F / 115°C)

Last Revision: 05/19/14

Advantages

• Solvent free, 100% solids will not shrink

• Non-slump, applies vertically and overhead

• 20 minute skin over

• No outgassing on damp surfaces

• Good color stability, will not suntan

• Paintable within 24 hours (See limitations)

• Gun grade, no special tools or mixing required

• Application at temperatures as low as 32°F (0°C)

Packaging

• 5 oz Squeeze Tube (148 ml)

36 tubes/carton, 40 cartons/pallet

• 10.1 oz (300 ml)

24 cartridges/carton, 45 cartons/pallet

• 20 oz (600 ml)

12 sausages/carton, 40 cartons/pallet

• 28 oz (825 ml)

12 cartridges/carton, 40 cartons/pallet

White only - Other colors available by

special order

• 2 and 5 gallon pails or 50 gallon drums

available by special order

Colors

White Gray Limestone

Black Tan

* Color matching is available in batch quantity only

Document No. L1270

Summary of content (4 pages)

PAGE 1
Technical Data Guide Polyether Technology CSI Section No. 07 92 13 CHEM LINK Brands Last Revision: 05/19/14 Document No. L1270 Telephone: 800-826-1681 Fax: 269-679-4448 353 E Lyon Street Schoolcraft, MI 49087 www.chemlink.com Product Description M-1® is a moisture curing, polyether adhesive sealant designed for applications in damp, dry, or cold climates. M-1® is solvent free and contains no isocyanates.
PAGE 2
Joint Preparation Joint surfaces should be clean, dry and free from all contamination including: dirt, oils, grease, tar, wax, rust and any other substance that may inhibit the sealant’s performance. Typical Physical Properties Gun Grade Zero Slump Joint Design Viscosity 1,200,000 cp +/- 400,000 cp Brookfield RVF TF Spindle, 4 RPM, 73°F (23°C) Density 11.8 +/- 0.2 lbs per gallon ASTM D1475 Tack Free Time 20 min +/- 10 min 45 +/- 5 % R.H.
PAGE 3
Application Guidelines: Concrete Prior to application remove any residual contamination by mechanical abrasion, sand blasting or power washing. On green concrete, remove all release agents, friable and loose concrete. Dry all visible and standing water prior to applying M-1®. Install an appropriate backer rod to avoid three-point bonding. Metal Prepare all metal to ensure maximum adhesion. Remove all rust, scale and residue by wire brushing to a bright metal sheen.
PAGE 4
NOTES: www.chemlink.com All properties described in this document are derived from testing conducted in laboratory conditions. Properties and performance will vary depending on environmental conditions and application technique. Test and evaluate to determine appropriate usage. Visit www.chemlink.com for the Safety Data Sheet, Technical Data Guides and full warranty for this product. LIMITED WARRANTY: Chem Link warrants this product’s performance, provided it is properly stored and applied within 1 year.