SK32303 ver. A1 User’s Manual CHENBRO User’s Manual SK32303 Version A1 May / 26 / 2008 15Fl., No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan R.O.C., Tel: +886 2 82265500 Fax: +886 2 82265392 Email: info@chenbro.com.tw 1 w w w . c h e n b r o .
SK32303 ver. A1 User’s Manual Copyright Copyright © 2006 CHENBRO Micom Co., Ltd.. All rights reserved. Unless otherwise indicated, all materials in this manual are copyrighted by CHENBRO Micom Co., Ltd.. All rights reserved. No part of this manual, either text or image may be used for any purpose other than internal use within purchasing company.
SK32303 ver. A1 User’s Manual Contents 15Fl., No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan R.O.C., Tel: +886 2 82265500 Fax: +886 2 82265392 Email: info@chenbro.com.tw 3 w w w . c h e n b r o . c o m Copyright......................................................................................................................................................2 Technical Support....................................................................................................................
SK32303 ver. A1 User’s Manual Revision History Date May / 26 / 2008 Modifications z First Release w w w . c h e n b r o . c o m 15Fl., No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan R.O.C., Tel: +886 2 82265500 Fax: +886 2 82265392 Email: info@chenbro.com.
SK32303 ver. A1 User’s Manual Safety Information z Read the installation instructions before connecting SK32303 to the power source. z Only trained and qualified personnel should be allowed to install, replace or service this equipment. z Never install this product in a wet environment. z Position system cables and power cables carefully; route system cable and the power cable and plug so that they cannot be stepped on or tripped over.
SK32303 ver. A1 User’s Manual Getting Start with the SK32303 Storage Kit Thank you for purchasing SK32303! This section covers unpacking and identifying components. Unpacking and Checking the Contents The complete SK32303 package includes the following items: Item Description Quantity SK32303 Storage Cage 1 Hot-swap 3.
SK32303 ver. A1 User’s Manual Introduction The CHENBRO SK32303 can house three 3.5” HDDs in a two 5.25” bays converter (Depth of 9.5” recommended). The ability for conversion allows existing servers to perform the maximum HDD density while keeping the flexibility. In all, SK32303 is the best solution as value added feature and performance. Functional Specification General z Support up to SATA-II and SAS (3.0 Gb/s) z Compatible with 3.
SK32303 ver. A1 User’s Manual Mechanical Dimension w w w . c h e n b r o . c o m 15Fl., No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan R.O.C., Tel: +886 2 82265500 Fax: +886 2 82265392 Email: info@chenbro.com.
SK32303 ver. A1 User’s Manual Components Description Front View 2. HDD power LED HDD 1 HDD 2 4. Alarm mute button 5. Overheat warning LED HDD 3 6. Fan failure LED 7. HDD failure LED 1. 3.5” HDD Hot-swap Tray 3. HDD activity / failure LED Device Function 1 3.
SK32303 ver. A1 User’s Manual Rear View – with Cover 2. Power connectors HDD 1 HDD 2 HDD 3 3. Buzzer 1. SATA / SAS connectors 7. 60mm fan 4. HDD activity signal jumper 5. HDD failure signal connector 6.
SK32303 ver. A1 User’s Manual Rear View – Cover Removed Fan & Temperature Switch Device Function Fan & Temperature Switch Refer to Page 14 Refer to page 16 for rear cover removal. w w w . c h e n b r o . c o m 15Fl., No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan R.O.C., Tel: +886 2 82265500 Fax: +886 2 82265392 Email: info@chenbro.com.
SK32303 ver. A1 User’s Manual Connector & Switch Definition HDD Failure Signal Connector This connector is for the SATA RAID card with HDD failure signal support such as ARECA ARC-1230 & 1260. Connect the failure signal connectors on SK32303 backplane and RAID card to activate the HDD failure LED.
SK32303 ver. A1 User’s Manual HDD Activity Signal Jumper The default jumpers are installed for SATA-II (3.0 Gb/s) HDDs which support activity signal via pin-11 of the connector on HDD. If using SATA-I (1.5 Gb/s) HDD, remove the jumper for HDD 1, 2 or 3 and connect the activity signal connectors on SK32303 backplane and RAID card to activate the HDD activity LED. The RAID card must support the HDD activity signal such as 3ware 8000 & 9000 series.
SK32303 ver. A1 User’s Manual Fan & Temperature Switch This switch is located behind the rear cover. Switch 1: Enable / Disable the fan. Switch 2: Change the threshold temperature of SK32303 storage kit Switch 1: Fan Enable / Disable 1 Fan Remark ON Enable Default OFF Disable Switch 2: Threshold Temperature Setting 2 Threshold Temperature ON 65 ℃ OFF 55 ℃ Remark Default Refer to page 16 for rear cover removal. w w w . c h e n b r o . c o m 15Fl., No.
SK32303 ver. A1 User’s Manual Installation Procedures The following is the installation procedures of HDD and rear cover assembly. Hot-swap HDD Assembly a. Push the blue latch of HDD tray and pull it out from the cage b. Attach HDD with six screws per tray w w w . c h e n b r o . c o m c. Insert HDD tray to the cage 15Fl., No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan R.O.C., Tel: +886 2 82265500 Fax: +886 2 82265392 Email: info@chenbro.com.
SK32303 ver. A1 User’s Manual Remove Rear Cover a. Unplug fan connector and remove four screws on the cover b. Remove rear cover c. Backplane w w w . c h e n b r o . c o m 15Fl., No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan R.O.C., Tel: +886 2 82265500 Fax: +886 2 82265392 Email: info@chenbro.com.
SK32303 ver. A1 User’s Manual Relative Part Number List CHENBRO Part Number Description Unit 80H045323-001 SK32303 LED Board pcs 80H105323-003 SK32303 3-Port SATA /SAS Backplane pcs 26H123215-002 SAS / SATA-II Cable, 700mm pcs 26H113215-005 HDD failure / activity signal Cable, 4P to 4P, 600mm pcs 83H305223-001 60mm (Thickness 25mm), Ball Bearing Fan pcs 83H555335-011 Hot-swap HDD Tray pcs Remark w w w . c h e n b r o . c o m 15Fl., No.
