VT-M2M-BTA-DE-A User’s Manual 1 / 28
Chengdu Vantron Technology, Ltd. www.vantrontech.
Table of Contents 1 2 Foreword ........................................................................................... 5 1.1 Copyright Notice ..................................................................... 5 1.2 Notes ............................................................................ 5 1.3 Statement ............................................................................ 6 1.4 Disclaimer ............................................................................ 6 1.
3.4 Operation Notice .................................................................... 20 3.4.1 4 Change SIM Card .................................................... 20 3.4.2 Power Supply .......................................................... 20 Tips ..................................................................................................
1 Foreword 1.1 Copyright Notice While all information contained herein have been carefully checked to assure its accuracy in technical details and printing, Vantron assumes no responsibility resulting from any error or features of this manual, or from improper uses of this manual or the software. Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual.
Sign Notice Type Description Notice Important information and regulations Caution Caution for latent damage to system or harm to personnel 1.3 Statement It is recommended to read and comply with this manual before operating VT-M2M-BTA-DE-A which provides important guidance and helps decreasing the danger of injury, electric shock, fire, or any damage to the device. 1.4 Disclaimer Vantron assumes no legal liability of accidents resulting from failure of conforming to the safety instructions. 1.
1.6 Safety Instructions Keep and comply with all operation instructions, warnings, and information. Pay attention to warnings on this device. Read the following precautions so as to decrease the danger of injury, electric shock, fire, or any damage to the device. Operations and Service instructions are provided with the equipment. Unit shall be used with indoor-use antenna only. No antenna for this unit can be installed outdoor. The maximum operation temperature is 61°C. 1.
Use tested power source This product still contains a button lithium battery as a real-time clock after its external power source is removed and therefore should not be short-circuited during transportation or placed under high temperature. Place cables properly: Do not place cables at any place with extrusion danger. 1.9 Cleaning Instructions Please power off before cleaning the device. Do not use spray detergent. Clean with a damp cloth.
2 Overview 2.1 Introduction Thank you for choosing Vantron. It is our commitment to provide our valued customers with the embedded devices equipped with the state-of-the-art technology and the best product services. Vantron’s VT-M2M-BTA-DE-A is based on the most advanced ARM and Intel Atom processors and has low-power consumption and high integration. The products are designed for applications of Gateway in industrials, medicals, financial, retail, vehicle, and transportations etc. 2.2 Product Series 2.
2.2.
3 VT-M2M-BTA-DE-A Hardware Instructions 3.
Top View 12 / 28
3.2 Specifications Specifications CPU Processor Intel® ATOM™, E3815/1.46GHz, 512KB L2 cache per core On Board RAM On Board DDRIII 1066MT/s , up to 2GB SSD Internal Half-Slim SSD Module Internal (16GB) Memory Resolution Up to 2560x1600@60Hz for VGA Display Wireless Communication Interface 1xVGA (DB15) WLAN Optional 802.
Accelerometer On Board Accelerometer, 3-Axis On board Registration Serial Number, and SHA-1 Security security Encrypt/Decrypt Chip DS28E01(Optional) Optional TPM module OS Linux, XOS, Paker’s pre-program golden image Software Applications Input SDK Available DC12 / 24V(9-36V), Locked Power Jack Power Consumption Dimensions Install Brackets 6W (Pulse10W), Sleep 2W. (without 4G,WLAN) 176x101x52mm (Box) 198x101x52mm Mechanical Weight Enclosure Temperature Environment Condition 0.6Kg (1.
3.3 Interface Description 3.3.1 Wide-Range Power Interface Power JACK with lock Pin Description 1,3 DGND (ground pin) 2 Power (+12 DC,UP to 36V) 3.3.2 Ethernet Interface Standard RJ45 interface, supporting 10M/100M/1000M self-adaptation, this is a standard RJ45 ethernet port.
3.3.
RS232/485 ,CAN,External IO Connector 12pins 3.81 pitch terminal with screw lock Load capacity: more than 128 nodes/RS485 channel Pin 1 2 3 4 5 6 7 8 9 10 11 12 Description TXD2/485_2_A RXD2/485_2_B DGND CANH CANL DGND EXTIO0 EXTIO1 EXTIO2 EXTIO3 EXTIO4 EXTIO5 17 / 28 Remarks BIOS set BIOS set 3.3V Level 3.3V Level 3.3V Level 3.3V Level 3.3V Level 3.
3.3.4 VGA Interface Standard vertical DB-15 Female VGA connector Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Description RED GREEN BLUE N.C. GND GND GND GND +5VDC GND N.C.
3.3.5 USB Host Connector Dual vertical USB A type interface, USB2.0 Pin A1 A2 A3 A4 B1 B2 B3 B4 Description USB1_VCC(+5VDC) USB1_DUSB1_D+ USB1_DGND(ground pin) USB2_VCC(+5VDC) USB2_DUSB2_D+ USB2_DGND(ground pin) Notes: Insert external device in USB1 connector should before powering up.
3.4 Operation Notice 3.4.1 Change SIM Card Push the small button on the left of SIM Card Holder, and install the SIM card to the holder. Then push the holder into the Slot. 3.4.2 Power Supply Please make sure using adapter in the accessory, or the power is not reversed when powered by other adapter.
4 Tips Waste Disposal It is recommended to disassemble the device before abandoning it in conformity with local regulations. Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do not throw batteries into fire (explosive) or put in common waste canister. Products or product packages with the sign of “explosive” should not be disposed like household waste but delivered to specialized electrical＆electronic waste recycling/disposal center.
Keep away from all energized circuits. Operators should not remove enclosure from the device. Only the group or person with factory certification is permitted to open the enclosure to adjust and replace the structure and components of the device. Do not change components unless the power cord is removed. In some cases, the device may still have residual voltage even if the power cord is removed. Therefore, it is a must to remove and fully discharge the device before contact so as to avoid injury.
Notice Considering that reasonable efforts have been made to assure accuracy of this manual, Vantron assumes no responsibility of possible missing contents and information, errors in contents, citations, examples, and source programs. Vantron reserves the right to make necessary changes to this manual without prior notice. No part of this manual may be reprinted or publicly released in forms of photocopy, tape, broadcast, e-document, etc. FCC Statement This device complies with Part 15 of the FCC Rules.
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ISED statement This radio transmitter [IC:11152A-BTADEALP] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
(1710-2700MHz) 3.0 dBi LTE (698-960MHz) Asian Creation AC-Q7027-YZW Diversity 50 SMA(Male) Monopole 50 SMA(Male) Monopole 5.0 dBi (1710-2700MHz) Shenzhen Norminson GPS NP002 28dBi Technology CO., LTD. This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s).
provide instructions and the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operation in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
US Office: Vantron Technology, Inc. Address: 440 Boulder Court, Suite 300, Pleasanton, CA 94566 Tel: +1 916-202-7042 Email: sales@vantrontech.com China Office: Chengdu Vantron Technology, Ltd. Address: No.5 GaoPeng Road, Hi-Tech Zone, Chengdu, SiChuan, P.R. China 610045 Tel: 86-28-8512-3930/3931, 8515-7572/6320 Email: sales@vantrontech.com.
