Welcome Thank you for purchasing a Bolt dona! The Bolt is a carbon fiber drone that introduces the exciting world of First Person View (FPV) piloting and racing Io everyone. Featuring an innovative FPV goggle and controller system, HD camera, altitude stabilization and a carbon fiber frame, the Bolt packs culling edge technology at a radical price point that offers amazing value. Before flying, please read through this User Manual carefully fo ensure safe and proper operation.
3. Esp away from obstacles and crowds 2. The aircraft must be operated away from crowds, tall buildings, power lines, and other obstacles. Do not operate the aircraft in non-ideal weather conditions such as wind and rain. 4. Esp the prefrontal dry 2. The aircraft components may be damaged by water, water vapor or humidity. Please ensure aircraft is not operated in environments that may cause damage to the repairer or its components. Make sure the aircraft is stored in a dry place §. Pr-flight Checklist a.
Charging Instructions for Drone Battery 1. Connect the drone battery or monitor battery with USE cable first and then choose one of the methods as shown below to connect with USB plug. 2. The red USB indicator lights up when charging and the light tums green when fully charged. * For faster charging, it is recommended {o use an adapter with 5V 2A output current {not included) to charge the battery.
Instruction for Drone, Transmitter and FPV Screen Drone Front (Camera) A Propeller B Propeller A Propeller y Clockwise Motor “srr Counter-clockwise Motor {Red and blue wire} | (Black and white wire} 7 TF Card Shot Counter-clockwise Motor Clockwise Motor {Black and white wire} {Red and blue wire} Specification Drone Size 296x271x80 5mm | Max Flying Distance/Radius | 150 m Fly Weight 222g Streaming Video Range | 130m Propeller Diameter 147mm Camera Resolution 1280x7200 Flying Time 14~16 mind Frequency GHz Dro
Exploded View No. Name Ne. Name No. Name 1 | Drone Co var Housing 11 | Rear LED Lampshade 21 | Main Frame 2 | Espalier (Clockwise) | 12 | Rear LED Board (Red) 22 | Front Carbon Fiber Board 3 | Gear Cover 13 | Rear Carbon Fiber Board 23 | Bottom Carbon Fiber Board 4.
Transmitter Monitor Holder Record Capture Photo Left Stick — Right Stick Headless #{ 4s Altitude Hold Bunion / HighiMediumiLow Speed press) Frequency Switching {Long press} a foe Brattain Cover 8 5 FPV Goggles Monitor Battery
Signal Channel Display Working Time Power Level .
Introduction to Transmitter Button Functions HighMediumfLow | Press down this bunion fo switch fo HighMediumA.ow Speed. Speed Made Long press it io swill the frequency. Move the Stick forward { backward { left / right to fly the drone fo up / down | um left { tun right.
Monitor Installation Instruction: 1. Pull out the holder until the monitor can be held (Picture 3), then unfold the lower clamp (Picture 4). 2. Put the monitor into the holder, then release the clamp, and the monitor will be fixed on the holder (Picture 5/6). Replete 4 Picture 5 Replete 8 Pre Flight Operation Instructions Frequency Pairing 1. Tum on the transmitter switch (Picture 7) and the power indicator light flashes rapidly.
3. Place the drone on a flat surface, the drone body lights turn from flashing to solid, which indicates frequency pairing is successful. Important Notice: Please make sure the drone is placed on a flat, even surface when powering on. Monitor Operation Instructions; 1. install the battery as Picture 15 shown. Warming: When the icon of power on the screen is red, it indicates that the battery is running out. Please replace the battery and charge the battery.
4. Press the button of CHANNEL or GROUP for about 1 second (Picture 16) to search the video frequency from the drone. The picture seen by the camera on the drone will show on the display screen when the search and sync is successful. Picture 16 CHANNEL/GROUP 5. Press down the MENU button of the monitor. When the screen shows as picture, press or *" button to adjust the brightness of the screen. Picture 17 6. Once again, press down the MENU button of the video.
7. Once again, press down the MENU button of the video. When the screen shows as pictures, press or “” button to adjust the saturation of the screen. Picture 19 Take-off 1. Make sure the camera is in forward direction of the drone. 2. Power on the drone and check the direction of the rotating propellers. The left front and right rear A propellers rotate clockwise while the right front and left rear B propellers rotate counterclockwise. 3. Slowly push up the Left Stick for the drone to take off.
3. Install the battery and Power on the drone and place if on a flat surface ina horizontal position. The drone body lights change from flashing to solid bright, which indicates successful frequency pairing. 4. Do not move the Left Stick before successful calibration. Push the Right Stick as Picture 22 shown and then release. The drone body lights flash, which indicates that the drone is calibrating.
Functions Altitude Hold Mode When the drone is flying, press down the Altitude Hold Button to enter Altitude Hold Mode (the front and rear lights of the drone flash two times in three seconds). Then the drone will keep flying at current altitude. It makes i easier to control the drone for beginners and gives stability for photography. Af the end of each flight, the function of altitude hold will automatically exit Altitudes Hold Button High/Medium/Low Speed Modes Press down this button.
Frequency porous ANNE CHY | CH2 | CH3 | CH4 | CH5 | CHE | CH7 | CHB FrA | 5645 | 5665 | 5685 | 5705 | 5885 | 5805 & 5025 | 5945 FrB 5740 | 5760 | 5780 | 5800 | 5820 | 5840 | 5860 | 5880 FrC | 5725 | 5745 | 5765 5785 | 5805 | 5625 | 5845 | 5865 FrD 5733 | 5752 | 5771 | 5790 | 5808 | 5828 & 5847 | 5866 FE 5658 | 5695 | 5732 | 5769 | 5806 | 5843 | 5880 | 5917 FrF 5362 | 5399 | 5436 5473 | 5510 | 5547 | 5584 | 5621 Video Record Bunion Make sure that you insert the TF card.
Headless Mode Under headless mods, the users can operate the drone without worrying about the orientation (left is left and right is right all the time, regardless of where your drone is pointing at). Headless Mode is designed for beginners and users who fly the drone in daylight or at a far distance. The default setting is NOT Headless Mode. You can activate the headless mode function before taking off or in flight.
Out of Range Warning When the drone is going to fly out of the max remote control distance, the transmitter will beep quickly to alarm the user fo fly the dons back immediately. Motors Jam Protection 1. When the propellers get stuck, the drone LED will flash quickly and activate stuck protection function and the motors will stop running. 2. Pull down the Left Stick to the lowest position. The drone LED becomes a solid light and stuck protection will be released, and the drone can fly again.
2. But the motor into motor holder (Picture 30), connect motor wire, install the frame, then fix the screw. ~N Picture 30 Picture 31 Picture 32 Picture 33 Notice: The motors rotating direction should be the same, or it will not work. Battery Installation Diagram When disassembling, you need to fight up the battery buckle {direction as Picture 34) and then pull out the battery (refer to Picture 10}. Picture 4 | To take photos and record video 1. insert the TF card fo the slot in accordance with Picture 35.
Troubleshooting Guide No.| Problem Problem Cause Solution 1. Low battery. 1. Replace the transmitter battery. Tr 2. The battery positive pole and negative 2. Install the battery in accordance with the 1 indicator pole are is reverse order. user manual. fights off 3. Clan the dirt between the battery and the 3. Poor Contact. battery sce. 1. Indicator light Is off 1. The same as shove 1.2.3 Facilitator | 2 Tess is interfering signal nearby. z postie drone ard power on the 2 he gore 3.
FCC Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference fo radio communications.
