Bumper-to-Bumper 3-years/36,000 miles (60 000 km) Limited Warranty Every 2000 S10 under warranty is backed with the following services: 1-800-CHEV-USA ( For Vehicles Purchased In Canada, call 1-800-268-6800) that provides in an emergency: Courtesy Transportation Free lockout assistance Free dead-battery assistance Free out-of-fuel assistance Free flat-tire change Emergency towing
2000 Chevrolet S10 Owner's Manual Litho in U.S.A.
Table of Contents Seats and Restraint Systems Section 1 Seats and Seat Controls Safety Belts Air Bag Systems Child Restraints Features and Controls Section 2 ii Keys and Door Locks Remote Keyless Entry (RKE) System Tailgate Automatic Transmission (If Equipped) Manual Transmission Operation (If Equipped) Four-Wheel Drive Operation (If Equipped) Parking Brake Windows Tilt Wheel Turn Signal/Multifunction Lever Windshield Wipers Cruise Control Interior and Exterior Lamps Mirrors Storage Compartments Acces
Table of Contents (cont'd) Comfort Controls and Audio Systems Section 3 Heating and Air Conditioning Setting the Radio Clock Radio/Cassette Player/CD Player Radio Theft-Deterrent Feature Steering Wheel Controls (If Equipped) Your Driving and the Road Section 4 Braking/Anti-lock Brakes (If Equipped) Traction Control System Steering Driving Tips for Various Road Conditions Off-Road Driving Recreational Vehicle Towing Loading Your Vehicle Towing a Trailer Problems on the Road Section 5 Hazard Warning Fl
Table of Contents (cont'd) Service and Appearance Care Section 6 Fuel Checking Fluids and Lubricants Bulb Replacement Windshield Wiper Blade Replacement Tires and Wheels Appearance Care Electrical System/Fuses and Circuit Breakers Capacities and Specifications Normal Maintenance Replacement Parts Maintenance Schedule Section 7 iv Scheduled Maintenance Periodic Maintenance Inspections Recommended Fluids and Lubricants Maintenance Records
Table of Contents (cont'd) Customer Assistance Information Section 8 Customer Satisfaction Procedures Customer Assistance Offices Roadside Assistance and Courtesy Transportation Warranty Information (See Warranty Manual) Reporting Safety Defects on page 8-10 Service Publications Index Section 9 In the Index you will find an alphabetical listing of almost every subject in this manual. You can use it to quickly find something you want to read.
We support voluntary technician certification. GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem and the name S10 PICKUP are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes in the product after that time without further notice.
How to Use this Manual Safety Warnings and Symbols Many people read their owner’s manual from beginning to end when they first receive their new vehicle. If you do this, it will help you learn about the features and controls for your vehicle. In this manual, you’ll find that pictures and words work together to explain things quickly. You will find a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning.
You will also find a circle with a slash through it in this book. This safety symbol means “Don’t,” “Don’t do this” or “Don’t let this happen.” In the notice area, we tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly. But the notice will tell you what to do to help avoid the damage. When you read other manuals, you might see CAUTION and NOTICE warnings in different colors or in different words.
Vehicle Symbols These are some of the symbols you may find on your vehicle.
Model Reference This manual covers these models: x
Service Station Guide For a More Detailed Look at What's Under the Hood Battery Cooling System See Section 6 See Section 5 Tire Pressure See Section 6 Spare Tire Pressure See Sections 5, 6 See Section 6 Hood Release See Section 6 Windshield Washer Fluid See Section 6 Engine Oil Dipstick See Section 6 Oil Viscosity Engine Oil See Section 6 Fuel Use unleaded gas only, 87 Octane or higher.
Section 1 Seats and Restraint Systems Here you’ll find information about the seats in your vehicle and how to use your safety belts properly. You can also learn about some things you should not do with air bags and safety belts.
Seats and Seat Controls This section tells you about the seats -- how to adjust them, and fold them up and down. Manual Front Seat CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you don’t want to. Adjust the driver’s seat only when the vehicle is not moving. 1-2 Move the lever under the front of the manual seat up to unlock it.
Manual Lumbar Support (If Equipped) If you have this feature, there will be a knob on the outside of the driver and passenger bucket seats. Turn the knob toward the front of the vehicle to increase lumbar support and toward the rear of the vehicle to decrease lumbar support. Reclining Seatbacks (Bucket Seats or 60/40 Bench) To adjust the front seatback, lift the lever on the outer side of the seat. Release the lever to lock the seatback where you want it.
CAUTION: But don’t have a seatback reclined if your vehicle is moving. 1-4 Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job because it won’t be against your body. Instead, it will be in front of you. In a crash you could go into it, receiving neck or other injuries. The lap belt can’t do its job either.
Seatback Latches The front seatback folds forward to let people get into the back seat or to access the storage area behind the seat. CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. Easy Entry Seat (Extended Cab Models) The right front bucket or split-bench seat of your vehicle makes it easy to get in and out of the rear vehicle area.
Jump Seat (Extended Cab Models) CAUTION: If an easy entry right front seat isn’t locked, it can move. In a sudden stop or crash, the person sitting there could be injured. After you’ve used it, be sure to push rearward on an easy entry seat to be sure it is locked. Your extended cab pickup has a jump seat in the rear area. D Tilt the seatback completely forward again to get out.
Safety Belts: They’re for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. And it explains the air bag system. CAUTION: Don’t let anyone ride where he or she can’t wear a safety belt properly. If you are in a crash and you’re not wearing a safety belt, your injuries can be much worse. You can hit things inside the vehicle or be ejected from it. You can be seriously injured or killed.
In most states and Canadian provinces, the law says to wear safety belts. Here’s why: They work. You never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one. Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. A few crashes are mild, and some crashes can be so serious that even buckled up a person wouldn’t survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider doesn’t stop.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield ... 1-10 or the instrument panel ...
Here Are Questions Many People Ask About Safety Belts -- and the Answers Q: Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense. A: You could be -- whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
Q: If I’m a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you’re in an accident -- even one that isn’t your fault -- you and your passengers can be hurt. Being a good driver doesn’t protect you from things beyond your control, such as bad drivers. Most accidents occur within 25 miles (40 km) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 km/h). Safety belts are for everyone.
4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt isn’t long enough, see “Safety Belt Extender” at the end of this section. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 3. Pick up the latch plate and pull the belt across you. Don’t let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Q: What’s wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. A: The shoulder belt is too loose. It won’t give nearly as much protection this way.
Q: What’s wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. A: The belt is buckled in the wrong place.
Q: What’s wrong with this? CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which aren’t as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen. A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
Q: What’s wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it. A: The belt is twisted across the body.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they don’t wear safety belts. To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Air Bag System Right Front Passenger Position Frontal air bags are designed to help reduce the risk of injury from the force of an inflating air bag. But these air bags must inflate very quickly to do their job and comply with federal regulations.
CAUTION: You can be severely injured or killed in a crash if you aren’t wearing your safety belt -- even if you have air bags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it. Air bags are “supplemental restraints” to the safety belts. All air bags are designed to work with safety belts, but don’t replace them. Air bags are designed to work only in moderate to severe crashes where the front of your vehicle hits something.
CAUTION: Anyone who is up against, or very close to, any air bag when it inflates can be seriously injured or killed. Air bags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its air bag system is designed for them. Young children and infants need the protection that a child restraint system can provide. Always secure children properly in your vehicle. To read how, see the part of this manual called “Children.
How the Air Bag System Works The right front passenger’s air bag is in the instrument panel on the passenger’s side. Where are the air bags? The driver’s air bag is in the middle of the steering wheel.
CAUTION: If something is between an occupant and an air bag, the bag might not inflate properly or it might force the object into that person. The path of an inflating air bag must be kept clear. Don’t put anything between an occupant and an air bag, and don’t attach or put anything on the steering wheel hub or on or near any other air bag covering. When should an air bag inflate? An air bag is designed to inflate in a moderate to severe frontal or near-frontal crash.
How does an air bag restrain? In moderate to severe frontal or near-frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. Air bags supplement the protection provided by safety belts. Air bags distribute the force of the impact more evenly over the occupant’s upper body, stopping the occupant more gradually.
D Let only qualified technicians work on your air bag system. Improper service can mean that your air bag system won’t work properly. See your dealer for service. AIR BAG OFF Switch Your vehicle has a switch on the instrument panel that you can use to turn off the right front passenger’s air bag. NOTICE: If you damage the covering for the driver’s or the right front passenger’s air bag, the bag may not work properly.
Infant. An infant (less than 1 year old) must ride in the front seat because: Medical Condition.
The AIR BAG OFF light will come on to let you know that the right front passenger’s air bag is off. The right front passenger’s air bag will remain off until you turn it back on again, and the AIR BAG OFF light will stay on to remind you that the air bag is off. CAUTION: To turn off the right front passenger’s air bag, insert your ignition key into the switch, push in, and move the switch to AIR BAG OFF.
Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are parts of the air bag system in several places around your vehicle. You don’t want the system to inflate while someone is working on your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag system. To purchase a service manual, see “Service and Owner Publications” in the Index.
Adding Equipment to Your Air Bag-Equipped Vehicle Q: If I add a push bumper or a bicycle rack to the front of my vehicle, will it keep the air bags from working properly? A: As long as the push bumper or bicycle rack is attached to your vehicle so that the vehicle’s basic structure isn’t changed, it’s not likely to keep the air bags from working properly in a crash. Q: Is there anything I might add to the front of the vehicle that could keep the air bags from working properly? A: Yes.
When you sit in a center seating position, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt. To make the belt shorter, pull its free end as shown until the belt is snug. Buckle, position and release it the same way as the lap part of a lap-shoulder belt. If the belt isn’t long enough, see “Safety Belt Extender” at the end of this section.
Rear Seat Passengers (Extended Cab Jump Seats) Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts. Lap Belt These are reserve seating positions equipped with lap belts only. (If your extended cab pickup has the optional side access panel, there’s only one reserve seating position.
Children Everyone in a vehicle needs protection! That includes infants and all children smaller than adult size. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle. Smaller Children and Babies CAUTION: To make it shorter, pull the belt as shown until it is snug.
CAUTION: Smaller children and babies should always be restrained in a child or infant restraint. The instructions for the restraint will say whether it is the right type and size for your child. A very young child’s hip bones are so small that a regular belt might not stay low on the hips, as it should. Instead, the belt will likely be over the child’s abdomen. In a crash, the belt would apply force right on the child’s abdomen, which could cause serious or fatal injuries.
CAUTION: Never hold a baby in your arms while riding in a vehicle. A baby doesn’t weigh much -- until a crash. During a crash a baby will become so heavy you can’t hold it. For example, in a crash at only 25 mph (40 km/h), a 12-lb. (5.5 kg) baby will suddenly become a 240-lb. (110 kg) force on your arms. The baby would be almost impossible to hold. Secure the baby in an infant restraint, but be sure to turn off the passenger’s air bag.
Child Restraints Every time infants and young children ride in vehicles, they should have protection provided by appropriate restraints. 1-36 Q: What are the different types of add-on child restraints? A: Add-on child restraints are available in four basic types. When selecting a child restraint, take into consideration not only the child’s weight and size, but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
An infant car bed (A) is a special bed made for use in a motor vehicle. It’s an infant restraint system designed to restrain or position a child on a continuous flat surface. With an infant car bed, make sure that the infant’s head rests toward the center of the vehicle. A rear-facing infant restraint (B) positions an infant to face the rear of the vehicle. Rear-facing infant restraints are designed for infants of up to about 20 lbs. (9 kg) and about one year of age.
1-38
A forward-facing child restraint (C-E) positions a child upright to face forward in the vehicle. These forward-facing restraints are designed to help protect children who are from 20 to 40 lbs. (9 to 18 kg) and about 26 to 40 inches (66 to 102 cm) in height, or up to around four years of age. One type, a convertible restraint, is designed to be used either as a rear-facing infant seat or a forward-facing child seat. A booster seat (F) is designed for children who are about 40 to 60 lbs.
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may find these instructions on the restraint itself or in a booklet, or both. These restraints use the belt system in your vehicle, but the child also has to be secured within the restraint to help reduce the chance of personal injury.
Top Strap An anchor bracket for a top strap is located at the rear of the seat cushion on the right front passenger’s seat. In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored.
Securing a Child Restraint in the Center Front Seat Position Don’t use child restraints in this position. The restraints won’t work properly. Anchor the top strap to this bracket. Once you have the top strap anchored, you’ll be ready to secure the child restraint itself.
Jump Seats (Extended Cab) Securing a Child Restraint in the Right Front Seat Position Don’t use child restraints in these positions. The restraints won’t work properly. Your vehicle has a right front passenger air bag. There’s a switch on the instrument panel that you can use to turn off the right front passenger’s air bag when you want to secure a rear-facing child restraint at the right front passenger’s position.
CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating air bag. Be sure to turn off the air bag before using a rear-facing child restraint in the right front seat position. If a forward-facing child restraint is suitable for your child, always move the passenger seat as far back as it will go.
CAUTION: If the air bag readiness light ever comes on when you have turned off the air bag, it means that something may be wrong with the air bag system. The right front passenger’s air bag could inflate even though the switch is off.
4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-46 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger. If you were using a rear-facing child restraint, turn on the right front passenger’s air bag when you remove the rear-facing child restraint from the vehicle unless the person who will be sitting there is a member of a passenger air bag risk group. See “AIR BAG OFF Switch” in the Index. CAUTION: 6.
Larger Children D Children who aren’t buckled up can strike other people who are. CAUTION: Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. Children who have outgrown child restraints should wear the vehicle’s safety belts.
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen. That could cause serious or fatal injuries. Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs.
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt isn’t long enough to fasten, your dealer will order you an extender. It’s free. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. The extender will be just for you, and just for the seat in your vehicle that you choose. Don’t let someone else use it, and use it only for the seat it is made to fit.
Section 2 Features and Controls Here you can learn about the many standard and optional features on your vehicle, and information on starting, shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is working properly -- and what to do if you have a problem.
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Don’t leave the keys in a vehicle with children.
This vehicle has one double-sided key for the ignition and door locks. It will fit with either side up. NOTICE: Your vehicle has a number of features that can help prevent theft. But you can have a lot of trouble getting into your vehicle if you ever lock your keys inside. You may even have to damage your vehicle to get in. So be sure you have extra keys. When a new vehicle is delivered, the dealer provides the owner with a pair of identical keys and a key code number.
Door Locks CAUTION: Unlocked doors can be dangerous. Passengers -- especially children -- can easily open the doors and fall out. When a door is locked, the inside handle won’t open it. Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. This may not be so obvious: You increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked.
Power Door Locks (If Equipped) Lockout Prevention To protect you from locking your key in the vehicle, this feature stops the power door locks from locking when the keys are in the ignition and a door is open. If the power lock switch is pressed when a door is open and the key is in the ignition, all the doors will lock, and the driver’s door will unlock. Leaving Your Vehicle If you are leaving the vehicle, take your keys, open your door and set the locks from inside. Then get out and close the door.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada.
Matching Transmitter(s) To Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. When the dealer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched.
1. Insert a dime in the slot between the covers of the transmitter housing near the key ring hole. Remove the bottom by twisting the dime. Side Access Panel (Extended Cab) (If Equipped) 2. Remove and replace the battery with a three volt CR2032 or equivalent battery, positive (+) side up. 3. Align the covers and snap them together. 4. Resynchronize the transmitter. 5. Check the operation of the transmitter.
Tailgate You can open the tailgate by pulling up on the handle while pulling the tailgate down. When you put the tailgate back up, be sure it latches securely. Follow these steps if you want to remove the tailgate: 1. Raise the tailgate slightly. 2. Remove both retaining cables. To remove each cable, turn it so the end faces the front. Then, push forward so the larger part of the hole is over the bolt. Pull the end over the bolt. 3.
Key in the Ignition If you leave your vehicle with the keys inside, it’s an easy target for joy riders or professional thieves -- so don’t do it. When you park your vehicle and open the driver’s door, you’ll hear a chime reminding you to remove your key from the ignition and take it with you. Always do this. Your steering wheel will be locked, and so will your ignition. If you have an automatic transmission, taking your key out also locks your transmission. Also remember to lock the doors.
3. Close all doors. The SECURITY light should go off after approximately 30 seconds. The alarm is not armed until the SECURITY light goes off. Testing the Alarm If a door is opened without the key or the remote keyless entry transmitter, the alarm will go off. Your vehicle’s headlamps will flash and the horn will sound for 110 seconds, then will turn off to save the battery power. 1. From inside the vehicle, lower the driver’s window and open the driver’s door.
PasslockR Your vehicle is equipped with the Passlock theft-deterrent system. Passlock is a passive theft-deterrent system. Passlock enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder is tampered with, fuel is disabled. During normal operation, the will go off approximately five seconds after the key is turned to the RUN ignition position.
Ignition Positions Use the key to turn the ignition switch to five different positions. ACCESSORY (A): This position lets you use things like the radio and the windshield wipers when the engine is off. Push in the key and turn it toward you. Your steering wheel will remain locked, just as it was before you inserted the key. NOTICE: Don’t operate accessories in the ACCESSORY position for long periods of time.
OFF (C): This position lets you turn off the engine but still turn the steering wheel. Use OFF if you must have your vehicle in motion while the engine is off (for example, if your vehicle is being towed). RUN (D): This is the position for driving. START (E): This position starts your engine. CAUTION: On manual transmission vehicles, turning the key to LOCK will lock the steering column and result in a loss of ability to steer the vehicle. This could cause a collision.
Key Release Button Retained Accessory Power The key cannot be removed from the ignition of manual transmission vehicles unless the key release button is used. Your vehicle is equipped with a Retained Accessory Power (RAP) feature which will allow certain features of your vehicle to continue to work up to 20 minutes after the ignition key is turned to OFF. Your radio and power windows will work when the ignition key is in RUN or ACCESSORY.
Manual Transmission The gear selector should be in NEUTRAL and the parking brake engaged. Hold the clutch pedal to the floor and start the engine. Your vehicle won’t start if the clutch pedal is not all the way down -- that’s a safety feature. Starting Your 2200 L4 Engine 1. Without pushing the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm.
Starting Your “VORTEC” 4300 V6 Engine 1. Without pushing the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. NOTICE: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2.
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the driver’s side of the engine compartment, behind the underhood fuse block. 3. Plug it into a normal, grounded 110-volt AC outlet. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things.
CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to PARK (P).
NEUTRAL (N): In this position, your engine doesn’t connect with the wheels. To restart when you’re already moving, use NEUTRAL (N) only. DRIVE (D): This position is for normal driving. If you need more power for passing, and you’re: D Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down. CAUTION: D Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
FIRST (1): This position gives you even more power but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the selector lever is put in FIRST (1) while the vehicle is moving forward, the transmission won’t shift into FIRST (1) until the vehicle is going slowly enough. Manual Transmission Operation 5-Speed This is your shift pattern. NOTICE: If your rear wheels can’t rotate, don’t try to drive.
SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the accelerator pedal. THIRD, FOURTH AND FIFTH (3, 4 and 5): Shift into THIRD (3), FOURTH (4) and FIFTH (5) the same way you do for SECOND (2). Slowly let up on the clutch pedal as you press the accelerator pedal. To stop, let up on the accelerator pedal and press the brake pedal.
Shift Light Four-Wheel Drive (If Equipped) If you have a manual transmission, you have a SHIFT light. This light will show you when to shift to the next higher gear for best fuel economy. When this light comes on, you can shift to the next higher gear if weather, road and traffic conditions let you. For the best fuel economy, accelerate slowly and shift when the light comes on. While you accelerate, it is normal for the light to go on and off if you quickly change the position of the accelerator.
Electronic Transfer Case (If Equipped) If your four-wheel-drive vehicle has the electronic transfer case, the transfer case switches are located to the right of the steering wheel. 4LO: This setting also engages your front axle to give you extra traction. You may never need 4LO. It sends the maximum power to all four wheels. You might choose 4LO if you were driving off-road in sand, mud or deep snow and climbing or descending steep hills. Indicator lights in the switches show you which setting you are in.
Shifting from 2HI or 4HI to 4LO To shift from 2HI or 4HI to 4LO, the vehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N) in vehicles equipped with an automatic transmission or the clutch pedal engaged in vehicles equipped with a manual transmission. The preferred method for shifting into 4LO is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the 4LO switch.
If the 4HI switch is pressed when your vehicle is in gear and/or moving, the 4HI indicator light will flash for 30 seconds but not complete the shift unless the vehicle is moving slower than 3 mph (4.8 km/h) and the transmission is in NEUTRAL (N) or the clutch pedal engaged. On automatic transmission equipped vehicles, if your transfer case does not shift into 4HI, your transmission indicator switch may require adjustment. With your transmission in NEUTRAL (N), press and release the 4HI switch.
Shifting Into PARK (P) (Automatic Transmission Only) 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) position like this: CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
Leaving Your Vehicle With the Engine Running (Automatic Transmission Only) CAUTION: D Move the lever up as far as it will go. It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Don’t leave your vehicle with the engine running unless you have to. 3.
Torque Lock (Automatic Transmission) If you are parking on a hill and you don’t shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To find out how, see “Shifting Into PARK (P)” in the Index.
Parking Your Vehicle (Manual Transmission Only) Parking Over Things That Burn Before you get out of your vehicle, turn off your engine, put your manual transmission in REVERSE (R) and firmly apply the parking brake. If you are parking on a hill, or if your vehicle is pulling a trailer, see “Towing a Trailer” in the Index. CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Don’t park over papers, leaves, dry grass or other things that can burn.
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can’t see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: D Your exhaust system sounds strange or different. D Your vehicle gets rusty underneath. D Your vehicle was damaged in a collision. D Your vehicle was damaged when driving over high points on the road or over road debris. D Repairs weren’t done correctly.
CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you’ve left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to PARK (P).
Press the side of the switch with the down arrow to lower the window. Swing-Out Windows (Extended Cab) To open a rear swing-out window, pull the latch toward the front of the vehicle and then push the latch out and rearward. Press the side of the switch with the up arrow to raise the window. Express-Down Window The driver’s window switch also has an express-down feature that allows you to lower it without holding the window switch.
Sliding Rear Window (If Equipped) Tilt Wheel (If Equipped) If you have the tilt steering wheel, you should adjust the steering wheel before you drive. Squeeze the latch in the center of the window and slide the glass to open it. When you close the window, be sure the latch catches. Horn Press the steering wheel pad to sound the horn. 2-34 You can raise it to the highest level to give your legs more room when you enter and exit the vehicle.
Turn Signal/Multifunction Lever Turn and Lane Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically. An arrow on the instrument panel cluster will flash in the direction of the turn or lane change.
Turn Signal On Chime Flash-To-Pass Feature If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each flash of the turn signal. To turn off the chime, move the turn signal lever to the off position. This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are in the automatic position.
Windshield Wipers For steady wiping at low speed, turn the band away from you to the LO position. For high-speed wiping, turn the band further, to HI. To stop the wipers, turn the band to OFF. Be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts.
Cruise Control (If Equipped) With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). If you have an automatic transmission and you apply your brakes, the cruise control will shut off. If you have a manual transmission and you apply your brakes or push the clutch pedal, the cruise control will shut off.
Setting Cruise Control CAUTION: If you leave your cruise control switch on when you’re not using cruise, you might hit a button and go into cruise when you don’t want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control switch to ON. 2. Get up to the speed you want. Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake.
Increasing Speed While Using Cruise Control Using Cruise Control on Hills There are two ways to go to a higher speed: How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control.
Exterior Lamps Turn the knob clockwise to the master lamps symbol to turn on all the lamps listed as well as the headlamps. Turn the knob all the way counterclockwise to turn off your lamps and put the system in auto headlamp mode. Automatic Headlamp System When it is dark enough outside, your automatic headlamp system will turn on your headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps and the instrument panel lights. The radio lights will also dim.
To idle your vehicle with the automatic headlamp system off, set the parking brake while the ignition is off. Then start your vehicle. The automatic headlamp system will stay off until you release the parking brake. As with any vehicle, you should turn on the regular headlamp system when you need it. Lamps On Reminder A reminder chime will sound when your headlamps or parking lamps are manually turned on and your ignition is in OFF, LOCK or ACCESSORY.
The following does not apply to vehicles first sold in Canada, and to some early production vehicles. Fog Lamps (If Equipped) When necessary, you may turn off the Automatic Headlamp System and the Daytime Running Lamps (DRL) feature by following the steps below: 1. Turn the ignition to RUN. 2. Press the DOME OVERRIDE button four times within six seconds. After the fourth press of the button, a chime will sound informing you that the system is off. 3.
Interior Lamps Brightness Control Turn the thumbwheel next to the headlamp switch up to make your instrument panel lights brighter. Turn the thumbwheel all the way up to turn on the interior lamps. Illuminated Entry Your vehicle is equipped with an illuminated entry feature. When the doors are opened, the dome lamps will come on if the DOME OVERRIDE button is in the “out” position.
You can use the DOME OVERRIDE button, located below the parking/headlamp knob, to set the dome lamps to come on automatically when the doors are opened, or to remain off. To turn the lamps off, press the button into the “in” position. With the button in this position, the dome lamps will remain off when the doors are open. To return the lamps to automatic operation, press the button again and return it to the “out” position.
Power Remote Control Mirror The control is located on the driver’s door armrest. Convex Outside Mirror A convex mirror’s surface is curved so you can see more from the driver’s seat. CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right or left lane, you could hit a vehicle. Check your inside mirror or glance over your shoulder before changing lanes.
Heated Outside Rearview Mirrors (If Equipped) Front Storage Area Your vehicle may be equipped with heated outside rearview mirrors. When you operate the heated mirror button on your climate control system, the defogger will warm the mirrors to help clear them of ice, snow or condensation. Storage Compartments Glove Box To open your glove box, lift the lever on the front of the glove box and lower the door. The glove box should not be open while driving.
Ashtray and Cigarette Lighter Rotate the front ashtray door down to open it. NOTICE: Don’t put papers and other things that burn into your ashtray. If you do, cigarettes or other smoking materials could set them on fire, causing damage. To remove the front ashtray, pull the bin upward. If your vehicle has the center armrest compartment, lift the cover to expose the storage area which includes slots for cassettes or compact discs and a coinholder.
NOTICE: Don’t hold a cigarette lighter in with your hand while it is heating. If you do, it won’t be able to back away from the heating element when it’s ready. That can make it overload, damaging the lighter and the heating element. Sun Visors To block out glare, you can swing down the sun visor. You can also swing the visor from side to side. Visor Vanity Mirror Pull the sun visor down and lift the cover to expose the vanity mirror.
Instrument Panel - Your Information System A. B. C. D. E. Air Vents Instrument Cluster Transfer Case (If Equipped) Glove Box Audio System 2-50 F. Heated Outside Rearview Mirror Switch (If Equipped) G. Auxiliary Power Outlets (If Equipped) H. Comfort Controls I. Ashtray J. Passenger Air Bag Off Switch K. Brake Release L. Fog Lamps (If Equipped) M.
Instrument Panel Cluster Your instrument cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel you’ve used, and many other things you’ll need to know to drive safely and economically.
Optional Cluster, Canada Similar 2-52
Speedometer and Odometer Tachometer (If Equipped) Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). The tachometer displays the engine speed in revolutions per minute (rpm). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Each tachometer has a different limit depending on the powertrain in your vehicle.
NOTICE: Do not operate the engine with the tachometer in the red range, or engine damage will occur. Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury.
Air Bag Readiness Light There is an air bag readiness light on the instrument panel, which shows the air bag symbol. The system checks the air bag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the air bag sensors, the air bag modules, the wiring, the passenger air bag suppression circuit and the crash sensing and diagnostic module. For more information on the air bag system, see “Air Bag” in the Index.
AIR BAG OFF Light When you turn the right front passenger’s air bag off, this light will come on and stay on to remind you that the air bag has been turned off. This light will go off when you turn the air bag back on again. See “AIR BAG OFF Switch” in the Index for more on this, including important safety information.
Charging System Indicator Light CAUTION: If the air bag readiness light ever comes on when you have turned off the air bag, it means that something may be wrong with the air bag system. The right front passenger’s air bag could inflate even though the switch is off.
Voltmeter Gage When your engine is not running, but the ignition is on (in RUN), this gage shows your battery’s state of charge in DC volts. You can only drive for a short time with the reading in either warning zone. If you must drive, turn off all unnecessary accessories. Readings in either warning zone indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible. Shift Light You have the shift light if you have a manual transmission.
Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. Your vehicle’s hydraulic brake system is divided into two parts. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well.
Anti-Lock Brake System Warning Light With the anti-lock brake Engine Coolant Temperature Gage system, this light will come on when you start your engine and may stay on for several seconds. That’s normal. If the light stays on, or comes on when you’re driving, your vehicle needs service. If the regular brake system warning light isn’t on, you still have brakes, but you don’t have anti-lock brakes.
Malfunction Indicator Lamp (Service Engine Soon Light) NOTICE: If you keep driving your vehicle with this light on, after a while, your emission controls may not work as well, your fuel economy may not be as good and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. United States Canada Your vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems.
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light doesn’t come on, have it repaired. This light will also come on during a malfunction in one of two ways: D Light Flashing -- A misfire condition has been detected. A misfire increases vehicle emissions and may damage the emission control system on your vehicle. Dealer or qualified service center diagnosis and service may be required.
Have you recently changed brands of fuel? Emissions Inspection and Maintenance Programs If so, be sure to fuel your vehicle with quality fuel (see “Fuel” in the Index). Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misfiring, hesitation on acceleration or stumbling on acceleration. (These conditions may go away once the engine is warmed up.
Oil Pressure Gage CAUTION: Don’t keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. United States Canada The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate oil pressure in kPa (kilopascals).
Security Warning Light This light will come on briefly when you turn the key toward START. The light will stay on until the engine starts. If the light flashes, the PasslockR system has entered a tamper mode. If the vehicle fails to start, see “Passlock” in the Index. If the light comes on continuously while driving and stays on, there may be a problem with the Passlock system. Your vehicle will not be protected by Passlock, and you should see your dealer.
Here are four things that some owners ask about. None of these show a problem with your fuel gage: Check Gages Light If this light comes on and stays on while you are driving, check your coolant temperature and engine oil pressure gages to see if they are in the warning zones. D At the gas station, the gas pump shuts off before the gage reads F (Full). D It takes a little more or less fuel to fill up than the gage indicated.
Section 3 Comfort Controls and Audio Systems In this section, you’ll find out how to operate the comfort control and audio systems offered with your vehicle. Be sure to read about the particular systems supplied with your vehicle.
Comfort Controls Mode Knob With these systems, you can control the heating, cooling and ventilation in your vehicle. The right knob on the control panel allows you to choose the direction of air delivery. Standard Climate Control System OFF: This setting turns the system off. Some outside air will still enter the vehicle whenever the vehicle is moving forward. VENT: This setting directs most of the air through the instrument panel outlets and a small amount through the floor outlets.
Optional Climate Control System Mode Knob The right knob on the control panel allows you to choose the direction of air delivery. OFF: This setting turns the system off. Some outside air will still enter the vehicle whenever the vehicle is moving forward. MAX A/C: This setting provides maximum cooling with the least amount of work. MAX A/C recirculates much of the air inside your vehicle so it cools quickly.
HEATER: This setting directs most of the warmed air through the heater floor outlets and some air through the windshield defroster outlets. BLEND: Airflow is divided equally between the heater floor outlet and the windshield defroster outlets. DEFROST: This setting directs most air through the windshield defroster outlets and some through the heater outlets. Air Conditioning (If Equipped) On hot days, open the windows long enough to let hot inside air escape.
Defogging and Defrosting On cool, humid days, use BLEND to keep the windshield and side windows clear. Use DEFROST to remove fog or ice from the windshield quickly in extreme humid or cold conditions. Turn the temperature knob clockwise and turn the fan control toward high. If you have the heated outside mirror feature, you can use it to defog or defrost your outside mirrors. For more information, see “Heated Outside Mirrors” in the Index.
Ventilation Tips D Keep the hood and front air inlet free of ice, snow or Setting the Clock for Systems with SET Button D When you enter a vehicle in cold weather, turn the Press SET. Within five seconds, press and hold the SEEK right arrow until the correct minute appears on the display. Press and hold the SEEK left arrow until the correct hour appears on the display. any other obstruction (such as leaves).
AM-FM Stereo Finding a Station AM-FM: Press the lower knob to switch between AM and FM. The display shows your selection. TUNE: Turn the lower knob to tune in radio stations. SEEK: Press the right arrow to tune to the next higher station and the left arrow to tune to the next lower station and stay there. Playing the Radio VOLUME: This knob turns the system on and off and controls the volume. To increase volume and turn the radio on, turn the knob clockwise.
PUSHBUTTONS: The four numbered pushbuttons let you return to your favorite stations. You can set up to 14 stations (seven AM and seven FM). Just: 3. Press two adjoining buttons at the same time, within five seconds. Whenever you press the same two buttons, the station you set will return. 1. Turn the radio on. 4. Repeat the steps for each pair of pushbuttons. 2. Press AM-FM to select the band. Setting the Tone 3. Tune in the desired station. 4. Press SET. (SET will appear on the display.
AM-FM Stereo with Cassette Tape Player (If Equipped) Finding a Station AM-FM: Press the lower knob to switch between AM, FM1 and FM2. TUNE: Turn the lower knob to tune in radio stations. SEEK: Press the right arrow to tune to the next higher station and the left arrow to tune to the next lower station. PUSHBUTTONS: The four numbered pushbuttons let you return to your favorite stations. You can set up to 21 stations (seven AM, seven FM1 and seven FM2). Just: 1. Turn the radio on. 2.
In addition to the four stations already set, up to three more stations may be preset on each band by pressing two adjoining buttons at the same time. Just: Setting the Tone 1. Tune in the desired station. TREB: Slide this lever up or down to increase or decrease treble. If a station is weak or noisy, you may want to decrease the treble. 2. Press SET. (SET will appear on the display.) 3. Press two adjoining buttons at the same time, within five seconds.
Playing a Cassette Tape CD Adapter Kits Your tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. It is possible to use a portable CD player adapter kit with your cassette tape player after activating the bypass feature on your tape player. Once the tape is playing, use the knobs for VOLUME, BAL, FADE, BASS and TREB just as you do for the radio.
AM-FM Stereo with Cassette Tape Player and Automatic Tone Control (If Equipped) SCV: Your system has a feature called Speed-Compensated Volume (SCV). With SCV, your audio system adjusts automatically to make up for road and wind noise as you drive. Set the volume at the desired level. Turn the control ring behind the upper knob clockwise to adjust the SCV. Then, as you drive, SCV automatically increases the volume, as necessary, to overcome noise at any particular speed.
SCAN: Press and hold SEEK for two seconds until SCAN appears on the display. SCAN allows you to listen to stations for a few seconds. The receiver will continue to scan and momentarily stop at each station until you press the button again. The sound will mute while scanning. 2. Press AM-FM to select the band. P.SCAN: The preset scan button lets you scan through your favorite stations stored on your pushbuttons. Select either the AM, FM1 or FM2 mode and then press P. SCAN.
AUTO TONE: Press this button to select among the six preset equalization settings and tailor the sound to the music or voice being heard. Each time you press the button, the selection will switch to one of the preset settings of CLASSIC, NEWS, ROCK, POP, C/W (Country/Western) or JAZZ. To return to the manual mode, press and release this button until the AUTO TONE display goes blank. This will return the tone adjustment to the BASS and TREB controls.
NEXT (3): Press the NEXT button or the SEEK right arrow to search for the next selection. A minimum three-second blank gap is required for the player to stop at the beginning of the selection. The tape direction arrow will blink during the SEEK operation. The sound will mute while searching for the next selection. AM-FM: Press this button to switch from a tape to the radio. REV (4): Press this button to rapidly reverse the tape to the beginning of the cassette or until you press REV again.
CD Adapter Kits It is possible to use a portable CD player adapter kit with your cassette tape player after activating the bypass feature on your tape player. AM-FM Stereo with Compact Disc Player and Automatic Tone Control (If Equipped) To activate the bypass feature, use the following steps: 1. Turn the ignition to RUN or ACCESSORY. 2. Turn the radio off. 3. Press and hold the TAPE AUX button for five seconds. The tape symbol on the display will flash for two seconds, indicating the feature is active.
SCV: Your system has a feature called Speed-Compensated Volume (SCV). With SCV, your audio system adjusts automatically to make up for road and wind noise as you drive. Set the volume at the desired level. Turn the control ring behind the upper knob clockwise to adjust the SCV. Then, as you drive, SCV automatically increases the volume, as necessary, to overcome noise at any particular speed. The volume level should always sound the same to you as you drive.
P.SCAN: The preset scan button lets you scan through your favorite stations stored on your pushbuttons. Select either the AM, FM1 or FM2 mode and then press P.SCAN. It will scan through each station stored on your pushbuttons and stop for a few seconds before continuing to scan through all of the pushbuttons. Press P.SCAN again or one of the pushbuttons to stop scanning to listen to a specific stored station. P.SCAN will light up on the display while in this mode.
Playing a Compact Disc PWR: Press this knob to turn the system on. (You can also turn the system on when you insert a compact disc into the player with the ignition on.) RDM (2): Press this button to play the tracks on the disc in random order. While in the RDM mode, RANDOM appears on the display. Press RDM again to return to normal play. Insert a disc partway into the slot, label side up. The player will pull it in. Wait a few seconds and the disc should play.
AM-FM: While in the CD mode, press this button to stop playing the CD and play the radio. The CD symbol will still display but the word CD will be replaced with either AM, FM1 or FM2. (If the radio is turned off, the disc stays in the player and will resume playing at the point where it stopped.) CD AUX: To switch between the player and the radio when a disc is playing, press the AM-FM button. To return to the player, press CD AUX.
The player automatically senses if the cassette tape is metal or CrO2 and adjusts for best playback sound. Anytime a cassette tape is inserted, the top side is selected for play first. PREV (1): Press PREV or the SEEK left arrow (in the opposite direction that the lighted tape direction arrow points) to search for the previous selection. A minimum three-second blank gap is needed for the player to stop at the beginning of the selection.
Theft-Deterrent Feature (If Equipped) THEFTLOCKR is designed to discourage theft of your radio. It works by using a secret code to disable all radio functions whenever battery power is removed. 1. Write down any three or four-digit number from 000 to 1999 and keep it in a safe place separate from the vehicle. 2. Turn the ignition to ACCESSORY or RUN. The THEFTLOCK feature for the radio may be used or ignored. If ignored, the system plays normally and the radio is not protected by the feature.
Unlocking the Theft-Deterrent Feature After a Power Loss Enter your secret code as follows; pause no more than 15 seconds between steps: Disabling the Theft-Deterrent Feature Enter your secret code as follows; pause no more than 15 seconds between steps: 1. Turn the ignition to ACCESSORY or RUN. 1. Turn the ignition on. LOC will appear on the display. 2. Turn the radio off. 2. Press MN and 000 will appear on the display. 3. Press the 1 and 4 buttons together.
To unlock a secured radio, see “Unlocking the Theft-Deterrent Feature After a Power Loss” earlier in this section. Understanding Radio Reception To help avoid hearing loss or damage: D Adjust the volume control to the lowest setting. D Increase volume slowly until you hear comfortably and clearly. AM The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other.
Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes or a damaged mechanism. Cassette tapes should be stored in their cases away from contaminants, direct sunlight and extreme heat. If they aren’t, they may not operate properly or may cause failure of the tape player. Your tape player should be cleaned regularly after every 50 hours of use.
If your vehicle is equipped with the AM-FM Stereo with Cassette Tape Player and Automatic Tone Control: 1. Turn the ignition to RUN or ACCESSORY. Cassettes are subject to wear and the sound quality may degrade over time. Always make sure the cassette tape is in good condition before you have your tape player serviced. 2. Turn the radio off. Care of Your Compact Discs 3. Press and hold the TAPE AUX button for five seconds. The tape symbol on the display will flash for two seconds.
Section 4 Your Driving and the Road Here you’ll find information about driving on different kinds of roads and in varying weather conditions. We’ve also included many other useful tips on driving.
Defensive driving really means “be ready for anything.” On city streets, rural roads or freeways, it means “always expect the unexpected.” Assume that pedestrians or other drivers are going to be careless and make mistakes. Anticipate what they might do. Be ready for their mistakes. Rear-end collisions are about the most preventable of accidents. Yet they are common. Allow enough following distance. It’s the best defensive driving maneuver, in both city and rural driving.
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It’s the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: D D D D Judgment Muscular Coordination Vision Attentiveness. Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving.
Since alcohol is carried in body water, this means that a woman generally will reach a higher BAC level than a man of her same body weight when each has the same number of drinks. The law in many U.S. states sets the legal limit at a BAC of 0.10 percent. In a growing number of U.S. states, and throughout Canada, the limit is 0.08 percent. In some other countries, it’s even lower. The BAC limit for all commercial drivers in the United States is 0.04 percent. The BAC will be over 0.
The body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. “I’ll be careful” isn’t the right answer. What if there’s an emergency, a need to take sudden action, as when a child darts into the street? A person with even a moderate BAC might not be able to react quickly enough to avoid the collision. There’s something else about drinking and driving that many people don’t know.
Control of a Vehicle Braking You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work at the places where the tires meet the road. Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That’s perception time. Then you have to bring up your foot and do it. That’s reaction time. Average reaction time is about 3/4 of a second.
Avoid needless heavy braking. Some people drive in spurts -- heavy acceleration followed by heavy braking -- rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking. If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life.
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. Here’s how anti-lock works. Let’s say the road is wet. You’re driving safely. Suddenly an animal jumps out in front of you. You slam on the brakes. Here’s what happens with ABS. You can steer around the obstacle while braking hard. A computer senses that wheels are slowing down.
Remember: Anti-lock doesn’t change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you won’t have time to apply your brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even though you have anti-lock brakes. Steering Tips Using Anti-Lock Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
Speed limit signs near curves warn that you should adjust your speed. Of course, the posted speeds are based on good weather and road conditions. Under less favorable conditions you’ll want to go slower. If you need to reduce your speed as you approach a curve, do it before you enter the curve, while your front wheels are straight ahead. Try to adjust your speed so you can “drive” through the curve. Maintain a reasonable, steady speed.
Off-Road Recovery Passing You may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again.
D Do not get too close to the vehicle you want to pass while you’re awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you’re following a larger vehicle. Also, you won’t have adequate space if the vehicle ahead suddenly slows or stops. Keep back a reasonable distance. D When it looks like a chance to pass is coming up, start to accelerate but stay in the right lane and don’t get too close.
Loss of Control Let’s review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) don’t have enough friction where the tires meet the road to do what the driver has asked. In any emergency, don’t give up. Keep trying to steer and constantly seek an escape route or area of less danger. Skidding In a skid, a driver can lose control of the vehicle.
Off-Road Driving with Your Four-Wheel-Drive Vehicle This off-road guide is for vehicles that have four-wheel drive. Also, see “Anti-Lock Brakes” in the Index. If your vehicle doesn’t have four-wheel drive, you shouldn’t drive off-road unless you’re on a level, solid surface. Off-road driving can be great fun. But it does have some definite hazards. The greatest of these is the terrain itself. “Off-roading” means you’ve left the great North American road system behind. Traffic lanes aren’t marked.
CAUTION: D Cargo on the load floor piled higher than D D the seatbacks can be thrown forward during a sudden stop. You or your passengers could be injured. Keep cargo below the top of the seatbacks. Unsecured cargo on the load floor can be tossed about when driving over rough terrain. You or your passengers can be struck by flying objects. Secure the cargo properly. Heavy loads on the roof raise the vehicle’s center of gravity, making it more likely to roll over.
Traveling to Remote Areas It makes sense to plan your trip, especially when going to a remote area. Know the terrain and plan your route. You are much less likely to get bad surprises. Get accurate maps of trails and terrain. Try to learn of any blocked or closed roads. It’s also a good idea to travel with at least one other vehicle. If something happens to one of them, the other can help quickly. Does your vehicle have a winch? If so, be sure to read the winch instructions.
Scanning the Terrain Off-road driving can take you over many different kinds of terrain. You need to be familiar with the terrain and its many different features. Here are some things to consider. Surface Conditions. Off-roading can take you over hard-packed dirt, gravel, rocks, grass, sand, mud, snow or ice. Each of these surfaces affects the steering, acceleration and braking of your vehicle in different ways.
Driving on Off-Road Hills Off-road driving often takes you up, down or across a hill. Driving safely on hills requires good judgment and an understanding of what your vehicle can and can’t do. There are some hills that simply can’t be driven, no matter how well built the vehicle. On a large hill, the incline may get steeper as you near the top, but you may not see this because the crest of the hill is hidden by bushes, grass or shrubs. Here are some other things to consider as you approach a hill.
Driving Uphill Once you decide you can safely drive up the hill, you need to take some special steps. D Use a low gear and get a firm grip on the steering wheel. D Get a smooth start up the hill and try to maintain your speed. Don’t use more power than you need, because you don’t want your wheels to start spinning or sliding. D Try to drive straight up the hill if at all possible. If the path D Ease up on your speed as you approach the top of the hill.
Q: What should I do if my vehicle stalls, or is about to stall, and I can’t make it up the hill? A: If this happens, there are some things you should do, and there are some things you must not do. First, here’s what you should do: D Push the brake pedal to stop the vehicle and keep it from rolling backwards. Also, apply the parking brake. Here are some things you must not do if you stall, or are about to stall, when going up a hill.
Driving Downhill When off-roading takes you downhill, you’ll want to CAUTION: consider a number of things: D How steep is the downhill? Will I be able to maintain vehicle control? D What’s the surface like? Smooth? Rough? Slippery? Hard-packed dirt? Gravel? D Are there hidden surface obstacles? Ruts? Logs? Boulders? D What’s at the bottom of the hill? Is there a hidden creek bank or even a river bottom with large rocks? If you decide you can go down a hill safely, then try to keep your vehicle headed
Q: A: Am I likely to stall when going downhill? It’s much more likely to happen going uphill. But if it happens going downhill, here’s what to do. D Stop your vehicle by applying the regular brakes. Apply the parking brake. D Shift to PARK (P) (or to NEUTRAL (N) with the manual transmission) and, while still braking, restart the engine. D Shift back to a low gear, release the parking brake, and drive straight down. D If the engine won’t start, get out and get help.
D Surface conditions can be a problem when you drive across a hill. Loose gravel, muddy spots, or even wet grass can cause your tires to slip sideways, downhill. If the vehicle slips sideways, it can hit something that will trip it (a rock, a rut, etc.) and roll over. D Hidden obstacles can make the steepness of the incline even worse. If you drive across a rock with the uphill wheels, or if the downhill wheels drop into a rut or depression, your vehicle can tilt even more.
Stalling on an Incline If your vehicle stalls when you’re crossing an incline, be sure you (and your passengers) get out on the uphill side, even if the door there is harder to open. If you get out on the downhill side and the vehicle starts to roll over, you’ll be right in its path. If you have to walk down the slope, stay out of the path the vehicle will take if it does roll over. CAUTION: Getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous.
Hard packed snow and ice offer the worst tire traction. On these surfaces, it’s very easy to lose control. On wet ice, for example, the traction is so poor that you will have difficulty accelerating. And if you do get moving, poor steering and difficult braking can cause you to slide out of control. If the water isn’t too deep, then drive through it slowly. At fast speeds, water splashes on your ignition system and your vehicle can stall. Stalling can also occur if you get your tailpipe under water.
After Off-Road Driving Driving at Night Remove any brush or debris that has collected on the underbody, chassis or under the hood. These accumulations can be a fire hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking. Check the body structure, steering, suspension, wheels, tires and exhaust system for damage. Also, check the fuel lines and cooling system for any leakage.
D Adjust your inside rearview mirror to reduce the glare from headlamps behind you. D Since you can’t see as well, you may need to slow down and keep more space between you and other vehicles. D Slow down, especially on higher speed roads. Your headlamps can light up only so much road ahead. D In remote areas, watch for animals. D If you’re tired, pull off the road in a safe place and rest. No one can see as well at night as in the daytime. But as we get older these differences increase.
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can’t stop, accelerate or turn as well because your tire-to-road traction isn’t as good as on dry roads. And, if your tires don’t have much tread left, you’ll get even less traction. It’s always wise to go slower and be cautious if rain starts to fall while you are driving. The surface may get wet suddenly when your reflexes are tuned for driving on dry pavement. The heavier the rain, the harder it is to see.
CAUTION: Wet brakes can cause accidents. They won’t work as well in a quick stop and may cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car wash, apply your brake pedal lightly until your brakes work normally. Hydroplaning Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles.
Hydroplaning usually happens at higher speeds. There just isn’t a hard and fast rule about hydroplaning. The best advice is to slow down when it is raining. Driving Through Flowing Water CAUTION: Driving Through Deep Standing Water Flowing or rushing water creates strong forces. If you try to drive through flowing water, as you might at a low water crossing, your vehicle can be carried away. As little as six inches of flowing water can carry away a smaller vehicle.
City Driving One of the biggest problems with city streets is the amount of traffic on them. You’ll want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: D Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip. D Try to use the freeways that rim and crisscross most large cities. You’ll save time and energy.
Freeway Driving At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic. Try to determine where you expect to blend with the flow. Try to merge into the gap at close to the prevailing speed. Switch on your turn signal, check your mirrors and glance over your shoulder as often as necessary. Try to blend smoothly with the traffic flow.
The exit speed is usually posted. Here are some things you can check before a trip: Reduce your speed according to your speedometer, not to your sense of motion. After driving for any distance at higher speeds, you may tend to think you are going slower than you actually are.
Highway Hypnosis Hill and Mountain Roads Is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
D Keep your vehicle in good shape. Check all fluid levels and also the brakes, tires, cooling system and transmission. These parts can work hard on mountain roads. D Know how to go down hills. The most important thing to know is this: let your engine do some of the slowing down. Shift to a lower gear when you go down a steep or long hill. CAUTION: If you don’t shift down, your brakes could get so hot that they wouldn’t work well. You would then have poor braking or even none going down a hill.
Winter Driving Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, a red cloth and reflective warning triangles. And, if you will be driving under severe conditions, include a small bag of sand, a piece of old carpet or a couple of burlap bags to help provide traction. Be sure you properly secure these items in your vehicle.
Whatever the condition -- smooth ice, packed, blowing or loose snow -- drive with caution. Accelerate gently. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more. Your anti-lock brakes improve your vehicle’s stability when you make a hard stop on a slippery road. Even though you have an anti-lock braking system, you’ll want to begin stopping sooner than you would on dry pavement. See “Anti-Lock” in the Index.
If You’re Caught in a Blizzard D Tie a red cloth to your vehicle to alert police that you’ve been stopped by the snow. D Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, floor mats -- anything you can wrap around yourself or tuck under your clothing to keep warm. If you are stopped by heavy snow, you could be in a serious situation.
CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You can’t see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking your exhaust pipe. And check around again from time to time to be sure snow doesn’t collect there. Open a window just a little on the side of the vehicle that’s away from the wind.
Dust or dirt can enter the back of the transmission through the opening created by removing the propeller shaft if proper protection is not provided. Also, check the transmission fluid level before driving the vehicle. Loading Your Vehicle When towing your vehicle, turn the ignition to OFF. To prevent your battery from draining while towing, remove the RDO BATT fuse from the instrument panel fuse block. Be sure to replace the fuse when you reach your destination.
The Certification/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline. Never exceed the GVWR for your vehicle, or the GAWR for either the front or rear axle. And, if you do have a heavy load, you should spread it out.
Payload CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash. D Put things in the cargo area of your vehicle. Try to spread the weight evenly. D Never stack heavier things, like suitcases, inside the vehicle so that some of them are above the tops of the seats. D Don’t leave an unsecured child restraint in your vehicle. D When you carry something inside the vehicle, secure it whenever you can.
Any load that extends beyond the vehicle’s taillamp area must be properly marked according to local laws and regulations. Remember not to exceed the Gross Axle Weight Rating (GAWR) of the rear axle. See “Loading Your Vehicle” in the Index. Add-On Equipment When you carry removable items, you may need to put a limit on how many people you carry inside your vehicle. Be sure to weigh your vehicle before you buy and install the new equipment.
Refer to the Truck-Camper Loading Information Label on the passenger’s door for dimensions A and B as shown in the following illustration. Here is an example of proper truck and camper match: A. Camper Center of Gravity Use the rear edge of the load floor for measurement purposes. The recommended location for the cargo center of gravity for the Cargo Weight Rating (C) is the point where the mass of a body is concentrated and, if suspended at that point, would balance the front and rear. 4-44 B.
You must weigh any accessories, trailer hitches or other equipment you add to your vehicle. Then, subtract this extra weight from the CWR. This extra weight may shorten the center of gravity zone for your vehicle. Your dealer can help you with this. If your slide-in camper and its load weigh less than the CWR, the center of gravity zone for your vehicle may be larger. Your dealer can help you make a good vehicle-camper match. He’ll also help you determine your CWR.
Towing a Trailer CAUTION: If you don’t use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well -- or even at all. You and your passengers could be seriously injured. Pull a trailer only if you have followed all the steps in this section. Ask your dealer for advice and information about towing a trailer with your vehicle.
If You Do Decide To Pull A Trailer If you do, here are some important points: D If you have the 2200 L4 (Code 5) engine, use regular gasoline (without ethanol) when pulling a trailer. See “Fuel” in the Index. D There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving. A good source for this information can be state or provincial police.
The following chart shows how much your trailer can weigh, based upon your vehicle model and options. # If your vehicle is equipped with a code 5 engine you must use regular unleaded gasoline rated at 87 octane or higher when towing. Vehicle Axle Ratio Max. Trailer Wt. 2WD 2.2L L4 Engine*# 3.73 4.10 2,000 lbs. (908 kg) 2,300 lbs. (1 044 kg) 2WD “VORTEC” 4300 V6, Auto. Trans.* 3.08 3.42 5,400 lbs. (2 451 kg) 6,400 lbs. (2 905 kg) 2WD “VORTEC” 4300 V6, Man. Trans.* 3.08 4,200 lbs.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle. And if you will tow a trailer, you must add the tongue load to the GVW because your vehicle will be carrying that weight, too.
Hitches Safety Chains It’s important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why you’ll need the right hitch. Here are some rules to follow: You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch.
Your trailer’s brake system can tap into the vehicle’s hydraulic brake system only if: D The trailer parts can withstand 3,000 psi (20 650 kPa) of pressure. D The trailer’s brake system will use less than 0.02 cubic inch (0.3 cc) of fluid from your vehicle’s master cylinder. Otherwise, both braking systems won’t work well. You could even lose your brakes. If everything checks out this far, then make the brake fluid tap at the port on the master cylinder that sends fluid to the rear brakes.
Backing Up Turn Signals When Towing a Trailer Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, just move that hand to the left. To move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you. When you tow a trailer, your vehicle has to have extra wiring and a heavy-duty turn signal flasher.
When towing at high altitude on steep uphill grades, consider the following: Engine coolant will boil at a lower temperature than at normal altitudes. If you turn your engine off immediately after towing at high altitude on steep uphill grades, your vehicle may show signs similar to engine overheating.
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: D Start your engine; D Shift into a gear; and D Release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks. 4-54 Maintenance When Trailer Towing Your vehicle will need service more often when you’re pulling a trailer. See the Maintenance Schedule for more on this.
Section 5 Problems on the Road Here you’ll find what to do about some problems that can occur on the road.
Hazard Warning Flashers Press the button on top of the steering column all the way down to make your front and rear turn signal lamps flash on and off. Your hazard warning flashers work no matter what position your key is in, and even if the key isn’t in. To turn off the flashers, press the button until the first click and release. Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off.
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. But please use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: D They contain acid that can burn you. D They contain gas that can explode or ignite. D They contain enough electricity to burn you. If you don’t follow these steps exactly, some or all of these things can hurt you.
2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles aren’t touching each other. If they are, it could cause a ground connection you don’t want. You wouldn’t be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the procedure. Put an automatic transmission vehicle in PARK (P) and a manual transmission vehicle in NEUTRAL (N). 3.
5. Check that the jumper cables don’t have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) and negative (-) will go to an unpainted metal engine part. Don’t connect positive (+) to negative (-) or you’ll get a short that would damage the battery and maybe other parts too. 6.
Don’t let the other end touch anything until the next step. The other end of the negative cable doesn’t go to the dead battery. It goes to a heavy unpainted metal part on the engine of the vehicle with the dead battery. 12. Remove the cables in reverse order to prevent electrical shorting. Take care that they don’t touch each other or any other metal. 9. Attach the cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move.
Towing Your Vehicle CAUTION: To help avoid serious personal injury to you or others: D Never let passengers ride in a vehicle that is being towed. D Never tow faster than safe or posted speeds. D Never tow with damaged parts not fully secured. D Never get under your vehicle after it has been lifted by the tow truck. D Always secure the vehicle on each side with separate safety chains when towing it. D Use only the correct hooks.
Engine Overheating You will find a coolant temperature gage on your vehicle’s instrument panel. See “Gages” in the Index. If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.
If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: D D D D Climb a long hill on a hot day. Stop after high-speed driving. Idle for long periods in traffic. Tow a trailer. See “Driving on Grades” in the Index. If you get the overheat warning with no sign of steam, try this for a minute or so: 1. If you have an air conditioner and it’s on, turn it off. 2.
Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see: A. Coolant Recovery Tank B. Radiator Pressure Cap C. Engine Fan 5-10 If the coolant inside the coolant recovery tank is boiling, don’t do anything else until it cools down. When the engine is cold, the coolant level should be at least up to the ADD mark. If it isn’t, you may have a leak in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Don’t touch them. If you do, you can be burned. Don’t run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle. NOTICE: Engine damage from running your engine without coolant isn’t covered by your warranty.
How to Add Coolant to the Coolant Recovery Tank If you haven’t found a problem yet, but the coolant level isn’t at the ADD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOLR engine coolant at the coolant recovery tank. (See “Engine Coolant” in the Index for more information.) CAUTION: (Continued) With plain water or the wrong mixture, your engine could get too hot but you wouldn’t get the overheat warning. Your engine could catch fire and you or others could be burned.
CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Don’t spill coolant on a hot engine. When the coolant in the coolant recovery tank is at the ADD mark, start your vehicle. If the overheat warning continues, there’s one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it.
CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap -- even a little -- they can come out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot. Wait for the cooling system and radiator pressure cap to cool if you ever have to turn the pressure cap.
How to Add Coolant to the Radiator 2. Then keep turning the pressure cap, but now push down as you turn it. Remove the pressure cap. 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise until it first stops. (Don’t press down while turning the pressure cap.) If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left.
3. Fill the radiator with the proper DEX-COOLR coolant mixture, up to the base of the filler neck. (See “Engine Coolant” in the Index for more information about the proper coolant mixture.) 5-16 4. Then fill the coolant recovery tank to the ADD mark. 5. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off.
6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. 7. By this time, the coolant level inside the radiator filler neck may be lower. If the level is lower, add more of the proper DEX-COOLR coolant mixture through the filler neck until the level reaches the base of the filler neck. 8. Then replace the pressure cap. At any time during this procedure if coolant begins to flow out of the filler neck, reinstall the pressure cap.
Engine Fan Noise If a Tire Goes Flat This vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions the clutch is not engaged. This improves fuel economy and reduces fan noise. Under heavy vehicle loading, trailer towing and/or high outside temperatures, the fan speed increases when the clutch engages. So you may hear an increase in fan noise.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. CAUTION: Changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people. You and they could be badly injured. Find a level place to change your tire. To help prevent the vehicle from moving: 1. Set the parking brake firmly. 2.
NOTICE: Never remove or store a tire from/to a storage position under the vehicle while the vehicle is supported by a jack. Always tighten the tire fully against the underside of the vehicle when storing it. Insert the chisel end of the wheel wrench, on an angle, into the hole in the rear bumper. This is the jack cover for the extended cab. The cover for the regular cab is similar. To remove it, turn the plastic wing nut counterclockwise. Remove the jack cover.
Turn the wheel wrench counterclockwise to lower the spare tire. Keep turning the wheel wrench until the spare tire can be pulled out from under the vehicle. When the tire has been completely lowered, tilt the retainer at the end of the cable and pull it through the wheel opening. Pull the tire out from under the vehicle. NOTICE: To help avoid vehicle damage, do not drive the vehicle before the cable is restored. Put the spare tire near the flat tire.
Position the bent end of your hub cap removal tool (shown), or the chisel end of your wheel wrench, in the notch of the hub cap and pry off the hub cap. Some of the molded plastic hub caps have imitation wheel nuts molded into them. The wheel wrench won’t fit these imitation nuts, so don’t try to remove them with the socket end of the wheel wrench. 5-22 If you have individual wheel nut caps that cover each nut, they must be removed in order to get to the wheel nuts.
Removing the Flat Tire and Installing the Spare Tire A. Front Frame Hole B. Rear Frame Hole (ZR2) 1. Using the wheel wrench, loosen all the wheel nuts. Don’t remove them yet. C. Spring Hanger Hole (Standard Pickups) 2. Turn the jack handle clockwise slightly to raise the jack lift head. 3. Fit the jack into the appropriate hole nearest the flat tire.
CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle. 5-24 4.
6. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 7. Place the spare on the wheel mounting surface. CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident.
Tighten each nut by hand until the wheel is held against the hub. If a nut can’t be turned by hand, use the wheel wrench and see your dealer as soon as possible. 9. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. 5-26 10. Use the wrench to tighten the wheel nuts firmly in a crisscross sequence as shown.
Storing a Flat or Spare Tire and Tools CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to 100 lb-ft (140 N·m).
1. Pull the retainer through the wheel. 2. Put the chisel end of the wheel wrench, on an angle, through the hole in the rear bumper and into the hoist shaft. 3. Raise the tire fully against the underside of the vehicle. Continue turning the wheel wrench until the tire is secure and the cable is tight. The spare tire hoist cannot be overtightened. A. B. C. D. E. Wheel Wrench Hoist Assembly Retainer Spring Tire 5-28 F. Valve Stem (Pointed Down) G. Lower H.
A. Wheel Wrench B. Bracket 4. Make sure the tire is stored securely. Push, pull, and then try to rotate or turn the tire. If the tire moves, use the wheel wrench to tighten the cable. C. Jacking Instructions (Roll and place tag behind the bracket after the tools are installed.) Return the jack, wheel wrench and wheel blocks to the proper location behind the seat. Secure the items. E. Wheel Blocks D. Bolt Location F. Nut G. Rubber Band H. Jack Position Replace the jack cover, if you have one.
Compact Spare Tire (If Equipped) Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). A. Bolt B. Cover (Standard Cab) C. Cover (Extended Cab) After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inflated.
Don’t use your compact spare on other vehicles. And don’t mix your compact spare tire or wheel with other wheels or tires. They won’t fit. Keep your spare tire and its wheel together. NOTICE: Tire chains won’t fit your compact spare. Using them can damage your vehicle and can damage the chains too. Don’t use tire chains on your compact spare. CAUTION: If you let your tires spin at high speed, they can explode, and you or others could be injured.
Rocking Your Vehicle To Get It Out Using the Recovery Hooks First, turn your steering wheel left and right. That will clear the area around your front wheels. If you have a four-wheel drive vehicle, shift into 4HI. Then shift back and forth between REVERSE (R) and a forward gear (or with a manual transmission, between FIRST (1) or SECOND (2) and REVERSE (R)), spinning the wheels as little as possible.
CAUTION: The recovery hooks, when used, are under a lot of force. Always pull the vehicle straight out. Never pull on the hooks at a sideways angle. The hooks could break off and you or others could be injured from the chain or cable snapping back. NOTICE: Never use the recovery hooks to tow the vehicle. Your vehicle could be damaged and it would not be covered by warranty.
Section 6 Service and Appearance Care Here you will find information about the care of your vehicle. This section begins with service and fuel information, and then it shows how to check important fluid and lubricant levels. There is also technical information about your vehicle, and a part devoted to its appearance care.
Service Doing Your Own Service Work Your dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ll get genuine GM parts and GM-trained and supported service people. If you want to do some of your own service work, you’ll want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see “Service and Owner Publications” in the Index.
CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. D Be sure you have sufficient knowledge, experience, the proper replacement parts and tools before you attempt any vehicle maintenance task. D Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt.
Be sure the posted octane is at least 87. If the octane is less than 87, you may get a heavy knocking noise when you drive. If it’s bad enough, it can damage your engine. If you’re using fuel rated at 87 octane or higher and you hear heavy knocking, your engine needs service. But don’t worry if you hear a little pinging noise when you’re accelerating or driving up a hill. That’s normal, and you don’t have to buy a higher octane fuel to get rid of pinging.
NOTICE: Your vehicle was not designed for fuel that contains methanol. Don’t use it. It can corrode metal parts in your fuel system and also damage plastic and rubber parts. That damage wouldn’t be covered under your warranty. Fuel E-85 (85% Ethanol) The 8th digit of your vehicle identification number (VIN) shows the code letter for your engine. You will find the VIN at the top left of your instrument panel. (See “Vehicle Identification Number” in the Index.
E-85 has less energy per gallon than gasoline, so you’ll need to refill your fuel tank more often when using E-85 than when you’re using gasoline. Use regular gasoline when pulling a trailer. For payload capacity with ethanol fuel see “Loading Your Vehicle” in the Index. NOTICE: Some additives are not compatible with E-85 fuel and may harm your fuel system. Damage caused by additives may not be covered by your new vehicle warranty. Don’t use additives with E-85 fuel.
Filling Your Tank CAUTION: Fuel vapor is highly flammable. It burns violently, and that can cause very bad injuries. Don’t smoke if you’re near fuel or refueling your vehicle. Keep sparks, flames and smoking materials away from fuel. The fuel cap is behind a hinged door on the driver’s side of your vehicle.
CAUTION: If you get fuel on yourself and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel filler cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel filler cap slowly and wait for any “hiss” noise to stop. Then unscrew the cap all the way. To remove the cap, turn it slowly to the left (counterclockwise).
When you put the cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See “Malfunction Indicator Lamp” in the Index. NOTICE: If you need a new cap, be sure to get the right type. Your dealer can get one for you. If you get the wrong type, it may not fit properly.
Checking Things Under the Hood CAUTION: Things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine. To open the hood, first pull the handle inside the vehicle on the lower left side of the instrument panel.
When you lift the hood, you’ll see these items on the 2200 L4 engine: A. B. C. D. Battery Coolant Recovery Tank Automatic Transmission Dipstick Engine Oil Fill Cap and Dipstick E. F. G. H. I.
When you lift the hood, you’ll see these items on the “VORTEC” 4300 V6 engine: A. B. C. D. E. Battery Coolant Recovery Tank Engine Oil Dipstick Engine Oil Fill Automatic Transmission Dipstick 6-12 F. G. H. I. J.
Before closing the hood, be sure all the filler caps are on properly. Then lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the hood and return the prop to its retainer. Then pull the hood down firmly to close. It will latch when dropped from 10 to 12 inches (25 to 30 cm) without pressing on the hood. The oil dipstick on the 2200 L4 engine is under the fill cap. Engine Oil Checking Engine Oil It’s a good idea to check your engine oil every time you get fuel.
Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level. When to Add Engine Oil If the oil is at or below the ADD line, then you’ll need to add at least one quart of oil. But you must use the right kind. This part explains what kind of oil to use. For crankcase capacity, see “Capacities and Specifications” in the Index. NOTICE: Don’t add too much oil.
What Kind of Engine Oil to Use Oils recommended for your vehicle can be identified by looking for the starburst symbol. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Do not use any oil which does not carry this starburst symbol. If you change your own oil, be sure you use oil that has the starburst symbol on the front of the oil container.
As shown in the chart, SAE 5W-30 is best for your vehicle. However, you can use SAE 10W-30 if it’s going to be 0_F (-18_C) or above. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils, such as SAE 20W-50. Engine Oil Additives Don’t add anything to your oil. The recommended oils with the starburst symbol are all you will need for good performance and engine protection.
Driving under these conditions causes engine oil to break down sooner. If any one of these is true for your vehicle, then you need to change your oil and filter every 3,000 miles (5 000 km) or 3 months -- whichever occurs first. If none of them is true, use the long trip/highway maintenance schedule. Change the oil and filter every 7,500 miles (12 500 km) or 12 months -- whichever occurs first. Driving a vehicle with a fully warmed engine under highway conditions causes engine oil to break down slower.
Engine Air Cleaner/Filter 2200 L4 Engine “VORTEC” 4300 V6 Engine 1. To remove either air cleaner, remove the fasteners that hold the cover on. 2. Remove the cover and lift out the air filter. 3. Insert a new air filter, then replace the air cleaner cover. 4. Tighten the fasteners to hold the cover in place. Refer to the Maintenance Schedule to determine when to replace the air filter. See “Scheduled Maintenance Services” in the Index.
CAUTION: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air, it stops flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Don’t drive with it off, and be careful working on the engine with the air cleaner/filter off. NOTICE: If the air cleaner/filter is off, a backfire can cause a damaging engine fire. And, dirt can easily get into your engine, which will damage it.
How to Check Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. NOTICE: Too much or too little fluid can damage your transmission. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire.
Checking the Fluid Level Then, without shutting off the engine, follow these steps: Prepare your vehicle as follows: D Park your vehicle on a level place. Keep the engine running. D With the parking brake applied, place the shift lever in PARK (P). D With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in PARK (P). D Let the engine run at idle for three minutes or more. 1.
How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See “Recommended Fluids and Lubricants” in the Index. Add fluid only after checking the transmission fluid while it is hot. (A cold check is used only as a reference.) If the fluid level is low, add only enough of the proper fluid to bring the level up to the HOT area for a hot check. It doesn’t take much fluid, generally less than one pint (0.5 L). Don’t overfill. 3.
Manual Transmission Fluid When to Check A good time to have it checked is when the engine oil is changed. However, the fluid in your manual transmission doesn’t require changing. Check the fluid level only when your engine is off, the vehicle is parked on a level place and the transmission is cool enough for you to rest your fingers on the transmission case.
How to Add Fluid When to Check and What to Use Here’s how to add fluid. Refer to the Maintenance Schedule to determine what kind of fluid to use. See “Recommended Fluids and Lubricants” in the Index. Refer to the Maintenance Schedule to determine how often you should check the fluid level in your clutch master cylinder reservoir and for the proper fluid. See “Owner Checks and Services” and “Recommended Fluids and Lubricants” in the Index. 1. Remove the filler plug. 2. Add fluid at the filler plug hole.
How to Check Lubricant Four-Wheel Drive Most lubricant checks in this section also apply to four-wheel-drive vehicles. However, they have two additional systems that need lubrication. Transfer Case When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See “Periodic Maintenance Inspections” in the Index. If the level is below the bottom of the filler plug hole, you’ll need to add some lubricant.
How to Check Lubricant Front Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See “Scheduled Maintenance Services” in the Index. How to Check Lubricant If the level is below the bottom of the filler plug hole, you’ll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the filler plug hole. Use care not to overtighten plug.
When the differential is cold, add enough lubricant to raise the level to 1/2 inch (12 mm) below the filler plug hole. A 50/50 mixture of clean, drinkable water and DEX-COOLR coolant will: When the differential is at operating temperature (warm), add enough lubricant to raise the level to the bottom of the filler plug hole. D D D D D What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See “Recommended Fluids and Lubricants” in the Index.
What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOLR coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid like alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture.
Checking Coolant CAUTION: Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. With the coolant recovery tank, you will almost never have to add coolant at the radiator. Never turn the radiator pressure cap -- even a little -- when the engine and radiator are hot. Add coolant mixture at the recovery tank, but be careful not to spill it. The vehicle must be on a level surface.
Radiator Pressure Cap NOTICE: Your radiator cap is a 15 psi (105 kPa) pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows on the cap line up with the overflow tube on the radiator filler neck. 6-30 Power Steering Fluid When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise.
How to Check Power Steering Fluid Adding Washer Fluid Turn the key off, let the engine compartment cool down, wipe the cap and the top of the reservoir clean, then unscrew the cap and wipe the dipstick with a clean rag. Replace the cap and completely tighten it. Then remove the cap again and look at the fluid level on the dipstick. For the VORTEC 4300 V6 engine, the level should be between the ADD and FULL marks. For the 2200 L4 engine, the fluid level should be at the C mark.
NOTICE: Brakes Brake Fluid D When using concentrated washer fluid, D D D follow the manufacturer’s instructions for adding water. Don’t mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water doesn’t clean as well as washer fluid. Fill your washer fluid tank only three-quarters full when it’s very cold.
So, it isn’t a good idea to “top off” your brake fluid. Adding brake fluid won’t correct a leak. If you add fluid when your linings are worn, then you’ll have too much fluid when you get new brake linings. You should add (or remove) brake fluid, as necessary, only when work is done on the brake hydraulic system. Checking Brake Fluid CAUTION: If you have too much brake fluid, it can spill on the engine. The fluid will burn if the engine is hot enough.
What to Add When you do need brake fluid, use only DOT-3 brake fluid. Refer to “Recommended Fluids and Lubricants” in the Index. Use new brake fluid from a sealed container only. NOTICE: D Using the wrong fluid can badly damage Always clean the brake fluid reservoir cap and the area around the cap before removing it. This will help keep dirt from entering the reservoir. CAUTION: With the wrong kind of fluid in your brake system, your brakes may not work well, or they may not even work at all.
CAUTION: The brake wear warning sound means that soon your brakes won’t work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced. NOTICE: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with your brakes.
Replacing Brake System Parts Vehicle Storage The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts. When you replace parts of your braking system -- for example, when your brake linings wear down and you have to have new ones put in -- be sure you get new approved GM replacement parts.
Bulb Replacement Headlamps Before you replace any bulbs, be sure that all the lamps are off and the engine isn’t running. See “Replacement Bulbs” in the Index. One-Piece Composite Headlamp System 1. Open the hood. For any bulb changing procedure not listed in this section, contact your GM dealer’s service department. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Two-Piece Composite Headlamp System 1. Open the hood. 5. Turn the bulb assembly counterclockwise to remove it. 6. Put the new bulb assembly into the headlamp assembly and turn it clockwise until it is tight. 2. Remove the black retainer clips by lifting up. 7. Plug in the electrical connector. 3. Pull the headlamp lens assembly out. 8. Put the headlamp assembly back into the vehicle. Install the two retaining clips.
One-Piece Front Turn Signal Lamp Assembly 1. Remove the headlamp assembly as shown under “One-Piece Composite Headlamp System” earlier in this section. 2. Twist the bulb socket counterclockwise to remove it from the headlamp assembly. 4. Turn the bulb assembly counterclockwise to remove it. 5. Put the new bulb assembly into the headlamp assembly and turn it clockwise until it is tight. 6. Plug in the electrical connector. 7. Put the headlamp lens assembly back into the vehicle.
Two-Piece Front Turn Signal Lamp Assembly 1. Remove the headlamp assembly as shown under “Two-Piece Composite Headlamp System” earlier in this section. 2. Locate the locking tabs on the assembly. Squeeze the tabs together and push that end of the assembly out while holding the tabs. The assembly will swing out. 4. Turn the harness bulb socket counterclockwise to remove it. Pull the bulb straight out to remove it from the socket. 5. Push the new bulb into the socket until it snaps into place. 3.
3. Remove the bulb. Center High-Mounted Stoplamp 4. Install a new bulb. 5. Replace the lens. Install and tighten the screws. 1. Remove the lens retaining screws. 2. Remove the lens. If equipment such as a cap or camper is installed on your vehicle, a center high-mounted stoplamp feed wire is provided along the driver’s side rear frame. This wire should be used to install a center high-mounted stoplamp in the cap or camper.
Taillamps 3. Pull the assembly away from the pickup side panel. 1. Open the tailgate. 4. Turn the socket counterclockwise to remove it. Push the tab in while you turn the socket. 2. Remove the screws from the lamp assembly near the tailgate latch. 5. Pull the bulb out. 6. Push the new bulb into the socket. 7. Put the socket into the assembly and turn the socket clockwise until it locks in place. 8. Replace the assembly. Install and tighten the screws. 9. Close the tailgate.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear and cracking. See “Wiper Blade Check” in Section 7 in this manual under Part B “Owner Checks and Services” for more information. NOTICE: Use care when removing or installing a blade assembly. Accidental bumping can cause the arm to fall back and strike the windshield. 1. To remove the old wiper blades, lift the wiper arm until it locks into a vertical position. A. Blade Assembly B. Arm Assembly C.
3. Remove the insert from the blade assembly. The insert has two notches at one end that are locked by bottom claws of the blade assembly. At the notched end, pull the insert from the blade assembly. A. Claw in Notch 4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully inserted. 5.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. CAUTION: (Continued) D Underinflated tires pose the same danger as CAUTION: Poorly maintained and improperly used tires are dangerous. D Overloading your tires can cause overheating as a result of too much friction. You could have an air-out and a serious accident.
Inflation -- Tire Pressure The Certification/Tire label, which is on the driver’s door door edge, above the door latch, shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). NOTICE: Don’t let anyone tell you that underinflation or overinflation is all right. It’s not.
Tire Inspection and Rotation Tires should be rotated every 6,000 to 8,000 miles (10 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It’s Time for New Tires” and “Wheel Replacement” later in this section for more information. Make sure the spare tire is stored securely. Push, pull, and then try to rotate or turn the tire. If it moves, use the wheel wrench to tighten the cable.
When It’s Time for New Tires CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. (See “Changing a Flat Tire” in the Index.
Buying New Tires To find out what kind and size of tires you need, look at the Certification/Tire label. The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each tire’s sidewall. When you get new tires, get ones with that same TPC Spec number. That way your vehicle will continue to have tires that are designed to give proper endurance, handling, speed rating, traction, ride and other things during normal service on your vehicle.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.
Temperature -- A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Used Replacement Wheels CAUTION: CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement. Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven.
NOTICE: (Continued) vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it’s contacting your vehicle, and don’t spin your wheels. If you do find traction devices that will fit, install them on the rear tires. If you have other size tires, use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires.
Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle: D D D D Alcohol Laundry Soap Bleach Reducing Agents Here are some cleaning tips: D D D D Always read the instructions on the cleaner label. Clean up stains as soon as you can -- before they set. Carefully scrape off any excess stain. Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn.
Special Fabric Cleaning Problems Cleaning Vinyl Stains caused by such things as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, vomit, urine and blood can be removed as follows: Use warm water and a clean cloth. 1. Carefully scrape off excess stain, then sponge the soiled area with cool water. D Things like tar, asphalt and shoe polish will stain if you 2. If a stain remains, follow the multi-purpose interior cleaner instructions described earlier. 3.
Cleaning the Top of the Instrument Panel Cleaning Glass Surfaces Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Glass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass.
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. (See “Recommended Fluids and Lubricants” in the Index.) Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle.
NOTICE: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may dull the finish or leave swirl marks. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter.
If your vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to the parts repaired or replaced to restore corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and other debris can collect. Dirt packed in closed areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.
GM Vehicle Care/Appearance Materials PART NUMBER 994954 1050172 1050173 1050174 1050214 1050427 SIZE 23 in. x 25 in. 16 oz. (0.473 L) 16 oz. (0.473 L) 16 oz. (0.473 L) 32 oz. (0.946 L) 23 oz. (0.
Vehicle Identification Number (VIN) Service Parts Identification Label You’ll find this label on the inside of the glove box. It’s very helpful if you ever need to order parts. On this label is: This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Electrical System Add-On Electrical Equipment NOTICE: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an air bag system. Before attempting to add anything electrical to your vehicle, see “Servicing Your Air Bag-Equipped Vehicle” in the Index.
Instrument Panel Fuse Block The instrument panel fuse block is at the driver’s end of the instrument panel. Remove the cover by turning the fastener counterclockwise. Extra fuses and the fuse extractor are provided in the cover. To reinstall the fuse panel cover, push in and turn the fastener clockwise.
Fuse/Circuit Breaker 3 4 5 6 7 8 9 10 11 12 6-64 Usage Cruise Control, Body Controls TBC, Cruise Module, Cruise Switch Gages, Body Controls TBC, Instrument Panel Cluster, B+ Power Parking Lamps, Power Window Switch, TBC, Ashtray Lamp Not Used Headlamp Switch, Body Controls TBC, Headlamp Relay Courtesy Lamps, Inadvertent Power Relay HVAC Control Head Turn Signal Instrument Panel Cluster, Engine Controls Interior Illumination Fuse/Circuit Breaker 13 14 15 16 17 18 19 20 21 22 23 24 Usage Auxiliary Power
Engine Compartment Fuse Block The fuse block is under the hood on the driver’s side of the engine compartment. Remove the cover by turning the fastener counterclockwise. To reinstall the fuse panel cover, push in and turn the fastener clockwise.
Name LT TRN RT TRN RR PRK TRL PRK LT HDLP RT HDLP FR PRK INT BAT ENG I ECM B ABS ECM I BTSI B/U LP A/C W/W PMP HORN IGN B RAP LD LEV 6-66 Usage Left Turn Signal Rear Right Turn Signal Rear Right Rear Parking Lamps Not Used Left Headlamp Right Headlamp Front Parking Lamps I/P Fuse Block Feed Engine Sensors/Solenoids, MAF, CAM, PURGE, VENT Engine Control Module, Fuel Pump Module, Oil Pressure Anti-Lock Brake System Engine Control Module Injectors Automatic Transmission Shift Lock Control System Back-Up Lamp
Replacement Bulbs Lamps Halogen Headlamps, Composite Low-Beam Halogen Headlamps, Composite High-Beam Tail and Stoplamps Front Sidemarker Lamps Front Turn Signal Lamps Center High-Mounted Stoplamp Quantity 2 2 2 2 2 2 Number 9006 HB4 9005 HB3 3057 194 3157NA 577 Capacities and Specifications Please refer to “Recommended Fluids and Lubricants” in the index for more information. See refrigerant change label under the hood for charge capacity information and requirements.
Automatic Transmission Capacity* Wheels and Tires Wheel Nut Torque . . . . . . . . . . . 100 lb-ft (140 N·m) Tire Pressure . . . . . . See the Certification/Tire label. See “Loading Your Vehicle” in the Index. Capacities (Approximate) Differential Fluid Cooling System Capacity* Engine 2200 L4 Auto./Manual “VORTEC” 4300 V6 Auto. “VORTEC” 4300 V6 Manual Quantity 11.5 quarts (11.0 L) 11.7 quarts (11.1 L) 11.9 quarts (11.
Normal Maintenance Replacement Parts Replacement part numbers listed in this section are based on the latest information available at the time of printing and are subject to change. If a part listed in this manual is not the same as the part used in your vehicle when it was built, or if you have any questions, please contact your GM dealer.
Vehicle Dimensions* Wheelbase Reg Cab Short Box . . . . . . 108.3 inches (275.1 cm) Reg Cab Long Box . . . . . . 117.9 inches (299.5 cm) Extended Cab . . . . . . . . . . 122.9 inches (312.2 cm) Length Reg Cab Short Box . . . . . . 189.0 inches (480.1 cm) Reg Cab Long Box . . . . . . 204.9 inches (520.4 cm) Extended Cab . . . . . . . . . . 203.6 inches (517.1 cm) Height 2WD Reg Cab . . . . . . . . . . . 62.1 inches (157.7 cm) 2WD Ext Cab . . . . . . . . . . . 62.2 inches (158.0 cm) 4WD Reg Cab Short Box . .
Section 7 Maintenance Schedule This section covers the maintenance required for your vehicle. Your vehicle needs these services to retain its safety, dependability and emission control performance.
Introduction Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance procedures are important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle.
How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” shows what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs. CAUTION: Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured.
Part A: Scheduled Maintenance Services Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we don’t know exactly how you’ll drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways.
Scheduled Maintenance Short Trip/City Definition Follow the Short Trip/City Scheduled Maintenance if any one of these conditions is true for your vehicle: D Most trips are less than 5 to 10 miles (8 to 16 km). This is particularly important when outside temperatures are below freezing. Short Trip/City Intervals Every 3,000 Miles (5 000 km): Engine Oil and Filter Change (or 3 months, whichever occurs first). Chassis Lubrication (or 3 months, whichever occurs first).
Scheduled Maintenance Short Trip/City Intervals Every 60,000 Miles (100 000 km): Engine Accessory Drive Belt Inspection. Every 100,000 Miles (166 000 km): Spark Plug Wire Inspection. Spark Plug Replacement. 4.3L V6 Engine Only: Positive Crankcase Ventilation (PCV) Valve Inspection. Every 150,000 Miles (240 000 km): Cooling System Service (or every 60 months, whichever occurs first). These intervals only summarize maintenance services.
Scheduled Maintenance Long Trip/Highway Intervals Long Trip/Highway Intervals Every 7,500 Miles (12 500 km): Engine Oil and Filter Change (or every 12 months, whichever occurs first). Chassis Lubrication (or every 12 months, whichever occurs first). Drive Axle Service. Tire Rotation. Every 60,000 Miles (100 000 km): Engine Accessory Drive Belt Inspection. Every 15,000 Miles (25 000 km): Automatic Transmission Service (severe conditions only).
Short Trip/City Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. The services shown at 150,000 miles (240 000 km) should be performed at the same interval after 150,000 miles (240 000 km). See “Owner Checks and Services” and “Periodic Maintenance Inspections” following. Footnotes [ The U.S.
Short Trip/City Scheduled Maintenance 3,000 Miles (5 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 9,000 Miles (15 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 15,000 Miles (25 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Inspect engine air cleaner filter if you are driving in dusty conditions. DATE ACTUAL MILEAGE SERVICED BY: Replace filter if necessary. An Emission Control Service. (See footnote [.) j Check rear/front axle fluid level and add fluid as needed.
Short Trip/City Scheduled Maintenance 18,000 Miles (30 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Short Trip/City Scheduled Maintenance 24,000 Miles (40 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Short Trip/City Scheduled Maintenance 30,000 Miles (50 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 33,000 Miles (55 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 39,000 Miles (65 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 45,000 Miles (75 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 48,000 Miles (80 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Short Trip/City Scheduled Maintenance 54,000 Miles (90 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Short Trip/City Scheduled Maintenance 60,000 Miles (100 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance j Replace engine air cleaner filter. An Emission Control Service. j Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. (See footnote +.) 63,000 Miles (105 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.
Short Trip/City Scheduled Maintenance 69,000 Miles (115 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 75,000 Miles (125 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j For Two-Wheel-Drive vehicles only: Clean and repack the front wheel bearings (or at each brake relining, whichever occurs first).
Short Trip/City Scheduled Maintenance 78,000 Miles (130 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Short Trip/City Scheduled Maintenance 84,000 Miles (140 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Short Trip/City Scheduled Maintenance 90,000 Miles (150 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance j Replace engine air cleaner filter. An Emission Control Service. j Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. (See footnote +.) 93,000 Miles (155 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.
Short Trip/City Scheduled Maintenance 99,000 Miles (165 000 km) j Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 3 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: velocity joints and axle seals for leaking. (See footnote **.
Short Trip/City Scheduled Maintenance 150,000 Miles (240 000 km) j Drain, flush and refill cooling system (or every 60 months since last service, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test cooling system and pressure cap. An Emission Control Service.
Long Trip/Highway Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. The services shown at 150,000 miles (240 000 km) should be performed at the same interval after 150,000 miles (240 000 km). See “Owner Checks and Services” and “Periodic Maintenance Inspections” following. Footnotes [ The U.S.
Long Trip/Highway Scheduled Maintenance 7,500 Miles (12 500 km) j Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 12 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Long Trip/Highway Scheduled Maintenance 15,000 Miles (25 000 km) (Continued) – When doing frequent trailer towing. – Uses such as found in taxi, police or delivery service. If you do not use your vehicle under any of these conditions, change the fluid and filter every 50,000 miles (83 000 km). Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. (See footnote +.
Long Trip/Highway Scheduled Maintenance 30,000 Miles (50 000 km) j Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 12 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.
Long Trip/Highway Scheduled Maintenance 37,500 Miles (62 500 km) j Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 12 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Long Trip/Highway Scheduled Maintenance j – When doing frequent trailer towing. – Uses such as found in taxi, police or delivery service. If you do not use your vehicle under any of these conditions, change the fluid and filter every 50,000 miles (83 000 km). Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. (See footnote +.
Long Trip/Highway Scheduled Maintenance 60,000 Miles (100 000 km) j Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 12 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.
Long Trip/Highway Scheduled Maintenance j Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. (See footnote +.) j Inspect engine accessory drive belt. An Emission Control Service. j Except 2200 Code 5 L4 Engine: Replace fuel filter. An Emission Control Service. (See footnote [.) j Replace engine air cleaner filter. An Emission Control Service.
Long Trip/Highway Scheduled Maintenance 75,000 Miles (125 000 km) j Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 12 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.
Long Trip/Highway Scheduled Maintenance 82,500 Miles (137 500 km) j Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service. j Lubricate chassis components (or every 12 months, whichever occurs first). (See footnote #.) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. (See footnote **.) j Rotate tires.
Long Trip/Highway Scheduled Maintenance – In hilly or mountainous terrain. – When doing frequent trailer towing. – Uses such as found in taxi, police or delivery service. If you do not use your vehicle under any of these conditions, change the fluid and filter every 50,000 miles (83 000 km). Replace fuel filter. An Emission Control Service. (See footnote [.) j Replace engine air cleaner filter. An Emission Control Service. j Rotate tires.
Long Trip/Highway Scheduled Maintenance 100,000 Miles (166 000 km) j Inspect spark plugwires. An Emission Control Service. j Replace spark plugs. An Emission Control Service. j If you haven’t used your vehicle under severe service conditions listed j DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: previously and, therefore, haven’t changed your automatic transmission fluid, change both the fluid and filter. Manual transmission fluid doesn’t require change. 4.
Part B: Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Part D.
At Least Twice a Year Restraint System Check Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken air bag coverings, and have them repaired or replaced.
Automatic Transmission Check Check the transmission fluid level; add if needed. See “Automatic Transmission Fluid” in the Index. A fluid loss may indicate a problem. Check the system and repair if needed. At Least Once a Year Key Lock Cylinders Service Lubricate the key lock cylinders with the lubricant specified in Part D. Hydraulic Clutch System Check Body Lubrication Service Check the fluid level in the clutch reservoir. See “Hydraulic Clutch Fluid” in the Index.
Starter Switch Check Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this check, the vehicle could move suddenly. If it does, you or others could be injured. Follow the steps below. CAUTION: When you are doing this check, the vehicle could move suddenly. If it does, you or others could be injured. Follow the steps below. 1. Before you start, be sure you have enough room around the vehicle. 2.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition key to LOCK in each shift lever position. D With an automatic transmission, the key should turn to LOCK only when the shift lever is in PARK (P). D With a manual transmission, the key should turn to LOCK only when you press the key release button. On all vehicles, the key should come out only in LOCK.
Part C: Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your dealer’s service department or other qualified service center do these jobs. Make sure any necessary repairs are completed at once. Proper procedures to perform these services may be found in a service manual. See “Service and Owner Publications” in the Index.
Throttle System Inspection Brake System Inspection Inspect the throttle system for interference or binding, and for damaged or missing parts. Replace parts as needed. Replace any components that have high effort or excessive wear. Do not lubricate accelerator and cruise control cables. Inspect the complete system. Inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition.
Part D: Recommended Fluids and Lubricants NOTE: Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. USAGE FLUID/LUBRICANT Engine Oil Engine Oil with the American Petroleum Institute Certified For Gasoline Engines starburst symbol of the proper viscosity. To determine the preferred viscosity for your vehicle’s engine, see “Engine Oil” in the Index.
USAGE FLUID/LUBRICANT USAGE FLUID/LUBRICANT Manual Transmission with L4 Engine Friction Modified Synchromesh Transmission Fluid (GM Part No. 12377916). Front and Rear Axle (Standard Differential) SAE 80W-90 Axle Lubricant (GM Part No. 1052271 or equivalent). Rear Axle (Locking Differential) Axle Lubricant; use only GM Part No. 1052271. Do not add friction modifier. Automatic Transfer Case AUTO-TRAK II Fluid (GM Part No. 12378508). Automatic Transmission DEXRONR-III Automatic Transmission Fluid.
USAGE FLUID/LUBRICANT USAGE FLUID/LUBRICANT Constant Velocity Universal Joint Chassis Lubricant (GM Part No. 12377985 or equivalent) or lubricant meeting requirements of NLGI # 2, Category LB or GC-LB. Fuel Filler Door and Rear Folding Seat Multi-Purpose Lubricant, SuperlubeR (GM Part No. 12346241 or equivalent). Clutch Pushrod to Clutch Fork Joint Chassis Lubricant (GM Part No. 12377985 or equivalent) or lubricant meeting requirements of NLGI # 2, Category LB or GC-LB.
Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service in the boxes provided after the maintenance interval. Any additional information from “Owner Checks and Services” or “Periodic Maintenance” can be added on the following record pages. Also, you should retain all maintenance receipts. Your owner information portfolio is a convenient place to store them.
Maintenance Record DATE ODOMETER READING SERVICED BY MAINTENANCE PERFORMED 7-53
Maintenance Record DATE 7-54 ODOMETER READING SERVICED BY MAINTENANCE PERFORMED
Maintenance Record DATE ODOMETER READING SERVICED BY MAINTENANCE PERFORMED 7-55
Maintenance Record DATE 7-56 ODOMETER READING SERVICED BY MAINTENANCE PERFORMED
Section 8 Customer Assistance Information Here you will find out how to contact Chevrolet if you need assistance. This section also tells you how to obtain service publications and how to report any safety defects.
Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
STEP TWO -- If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, contact the Chevrolet Customer Assistance Center by calling 1-800-222-1020. In Canada, contact GM of Canada Customer Communication Centre in Oshawa by calling 1-800-263-3777 (English) or 1-800-263-7854 (French). We encourage you to call the toll-free number in order to give your inquiry prompt attention.
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you are required to resort to this informal dispute resolution program prior to filing any court action, use of the program is free of charge and your case will generally be heard within 40 days.
Canada General Motors of Canada Limited Customer Communication Centre, 163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800 All Overseas Locations GMODC - Customer Communication Centre 169-007 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 Telephone: 905-644-4112 Fax: 905-644-4866 Caribbean Numbers 1-800-496-9992 (English) Puerto Rico 1-800-496-9993 (Spanish) Puerto Ric
Chevrolet Roadside Assistance Program If your problem cannot be resolved over the phone, our advisors have access to a nationwide network of dealer recommended service providers. Roadside membership is free; however some services may incur costs. Roadside offers two levels of service to the customer, Basic Care and Courtesy Care: D D D D To enhance Chevrolet’s strong commitment to customer satisfaction, Chevrolet is excited to announce the establishment of the Chevrolet Roadside Assistance Center.
Chevrolet offers Courtesy Transportation for customers needing warranty service. Courtesy Transportation will be offered in conjunction with the coverage provided by the Bumper-to-Bumper New Vehicle Limited Warranty to eligible purchasers of 2000 Chevrolet passenger cars and light duty trucks. (Please see your selling dealer for details.
Courtesy Transportation Chevrolet has always exemplified quality and value in its offering of motor vehicles. To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for new vehicles. The Courtesy Transportation program is offered to retail purchase/lease customers in conjunction with the Bumper-to-Bumper coverage provided by the New Vehicle Limited Warranty.
Courtesy Rental Vehicle When your vehicle is unavailable due to overnight warranty repairs, your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle you obtained, at actual cost, up to a maximum of $30.00 per day supported by receipts. This requires that you sign and complete a rental agreement and meet state, local and rental vehicle provider requirements. Requirements vary and may include minimum age requirements, insurance coverage, credit card, etc.
REPORTING SAFETY DEFECTS TO THE UNITED STATES GOVERNMENT If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying General Motors. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
REPORTING SAFETY DEFECTS TO GENERAL MOTORS Ordering Owner Publications in Canada In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-222-1020, or write: Owner’s manuals are available for purchase for all current and most past model General Motors vehicles. Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
2000 CHEVROLET SERVICE PUBLICATIONS ORDERING INFORMATION The following publications covering the operation and servicing of your vehicle can be purchased by filling out the Service Publication Order Form in this book and mailing it in with your check, money order, or credit card information to Helm, Incorporated (address below.
ORDER TOLL FREE (NOTE: For Credit Card Holders Only) 1-800-551-4123 (Monday-Friday 8:00 AM – 6:00 PM EST) FAX Orders Only 1-313-865-5927 2 0 0 0 PUBLICATION FORM NUMBER Orders will be mailed within 10 days of receipt. Please allow adequate time for postal service. If further information is needed, write to the address shown below or call 1-800-551-4123. Material cannot be returned for credit without packing slip with return information within 30 days of delivery.
