2002 Chevrolet TrailBlazer Owner's Manual Litho in U.S.A.
Table of Contents Seats and Restraint Systems Section 1 Seats and Seat Controls Safety Belts Air Bag Systems Restraint Systems for Children Features and Controls Section 2 ii Windows Keys and Door Locks Remote Keyless Entry System (If Equipped) Liftgate/Liftglass Automatic Transmission Four-Wheel Drive (If Equipped) Parking Brake Tilt Wheel Turn Signal/Multifunction Lever Windshield Wipers Cruise Control Exterior and Interior Lamps Mirrors Storage Compartments Luggage Carrier Accessory Power Outlets O
Table of Contents (cont'd) Comfort Controls and Audio Systems Section 3 Heating and Air Conditioning Setting the Radio Clock Radio/Cassette Player/CD Player Radio Theft-Deterrent Feature Steering Wheel Controls (If Equipped) Your Driving and the Road Section 4 Defensive Driving Drunken Driving Control of a Vehicle Braking Steering Driving Tips for Various Road Conditions Off-Road Driving Recreational Vehicle Towing Loading Your Vehicle Towing a Trailer Problems on the Road Section 5 Hazard Warning Fl
Table of Contents (cont'd) Service and Appearance Care Section 6 Fuel Checking Fluids and Lubricants Engine Air Cleaner/Filter Brakes Bulb Replacement Windshield Wiper Blade Replacement Tires and Wheels Appearance Care Electrical System/Fuses and Circuit Breakers Capacities and Specifications Normal Maintenance Replacement Parts Maintenance Schedule Section 7 iv Scheduled Maintenance Owner Checks and Services Periodic Maintenance Inspections Recommended Fluids and Lubricants Maintenance Records
Table of Contents (cont'd) Customer Assistance Information Section 8 Customer Satisfaction Procedures Customer Assistance Offices Roadside Assistance and Courtesy Transportation Warranty Information (See Warranty Manual) Reporting Safety Defects on page 8-10 Service Publications Index Section 9 In the Index you will find an alphabetical listing of almost every subject in this manual. You can use it to quickly find something you want to read.
We support voluntary technician certification. GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem and the name TRAILBLAZER are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice. For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division whenever it appears in this manual.
Safety Warnings and Symbols 4-Door Utility About Driving Your Vehicle As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read the “on-pavement” and “off-road” driving guidelines in this manual. (See “Your Driving, the Road and Your Vehicle” and “Off-Road Driving with Your Four-Wheel-Drive Vehicle” in the Index.
You will also find a circle with a slash through it in this book. This safety symbol means “Don’t,” “Don’t do this” or “Don’t let this happen.” When you read other manuals, you might see CAUTION and NOTICE warnings in different colors or in different words. You’ll also see warning labels on your vehicle. They use the same words, CAUTION or NOTICE. Vehicle Symbols Vehicle Damage Warnings Also, in this book you will find these notices: NOTICE: These mean there is something that could damage your vehicle.
ix
Service Station Guide Windshield Washer Fluid See Section 6 Cooling System See Section 5 For a More Detailed Look at What's Under the Hood Tire Pressure See Section 6 Spare Tire Pressure See Section 6 See Section 6 Hood Release See Section 6 Battery See Section 6 Engine Oil Dipstick See Section 6 Oil Viscosity Engine Oil See Section 6 Fuel Use unleaded only. See Section 6 for octane ratings.
Section 1 Seats and Restraint Systems Here you’ll find information about the seats in your vehicle and how to use your safety belts properly. You can also learn about some things you should not do with air bags and safety belts.
Seats and Seat Controls This section tells you about the manual and power seats -- how to adjust them, and also about the reclining front seatbacks, memory seats, lumbar adjustments and heated seats. Power Seats (If Equipped) If you have this feature, the power seat controls are located on the outboard side of the front seat cushions. Manual Front Seat CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving.
D Lift up or push down on the center of the seat control to move the entire seat up or down. D To move the seat forward or rearward, slide the seat control forward or rearward. D To recline the seatback, press the vertical control rearward. To raise the seatback, press the vertical control forward. Manual Lumbar Control This control is located on the outboard side of the seat.
Memory Seat (If Equipped) If your vehicle has this feature the controls are located on the driver’s door, and are used to program and recall memory settings for the driver’s seating and outside mirror positions. Adjust the driver’s seat (including the seatback recliner and lumbar) and both of the outside mirrors to the desired position. Then press and hold button 1 (for driver 1) for three seconds. A chime will sound to let you know that the position has been stored.
Two personalized exit positions can be set by first recalling the driver’s position (by pressing 1 or 2), then positioning the seat in the desired exit position for that driver. Then press and hold the button with the exit symbol for three seconds. A chime will sound to let you know that the position has been stored. With the vehicle in PARK (P), the exit position for that driver can be recalled by pressing the exit button.
Reclining Front Seatbacks If your vehicle has a manual recliner, lift the lever located on the outboard side of the seat and push the seatback rearward to recline the seatback. To return the seatback to the normal position, lift the lever without pushing rearward on the seatback and the seatback will move forward. If your vehicle has power seat controls, the vertical power seat control described earlier allows the seatback to recline. But don’t have a seatback reclined if your vehicle is moving.
Head Restraints CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job. In a crash, you could go into it, receiving neck or other injuries. The lap belt can’t do its job either. In a crash the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries.
Rear Seats Your vehicle has a folding rear seat which lets you fold the seatbacks down for more cargo space. The rear seatback handles are located on the outboard side of the rear seatbacks. Pull the seatback toward you as you lift up on the handle. The head restraint will automatically fold out of the way when the seatback is folded down. Pull up on the tab located where the seat cushion meets the seatback to fold the seat cushion up and out of the way.
Safety Belts: They’re for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. And it explains the air bag system. CAUTION: To return the head restraint to the upright position, reach behind the seat and pull the restraint up until it locks into place. Push and pull on the head restraint to make sure that it is latched securely. Don’t let anyone ride where he or she can’t wear a safety belt properly.
CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. Your vehicle has a light that comes on as a reminder to buckle up. See “Safety Belt Reminder Light” in the Index.
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it’s just a seat on wheels.
Get it up to speed. Then stop the vehicle. The rider doesn’t stop. 1-12 The person keeps going until stopped by something. In a real vehicle, it could be the windshield ...
or the instrument panel ... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense.
Here Are Questions Many People Ask About Safety Belts -- and the Answers Q: Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? A: You could be -- whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down. And your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
How to Wear Safety Belts Properly Adults This part is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see the part of this manual called “Children.” Follow those rules for everyone’s protection. First, you’ll want to know which restraint systems your vehicle has. We’ll start with the driver position.
5. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder belt. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest.
Q: What’s wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. A: The shoulder belt is too loose. It won’t give nearly as much protection this way.
Q: What’s wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. A: The belt is buckled in the wrong place.
Q: What’s wrong with this? CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which aren’t as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen. A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
Q: What’s wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it. A: The belt is twisted across the body.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they don’t wear safety belts. To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Right Front Passenger Position To learn how to wear the right front passenger’s safety belt properly, see “Driver Position” earlier in this section.
CAUTION: (Continued) Frontal air bags for the driver and right front passenger are designed to work only in moderate to severe crashes where the front of your vehicle hits something. They aren’t designed to inflate at all in rollover, rear, side or low-speed frontal crashes. And, for some unrestrained occupants, frontal air bags may provide less protection in frontal crashes than more forceful air bags have provided in the past.
CAUTION: Anyone who is up against, or very close to, any air bag when it inflates can be seriously injured or killed. Air bags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its air bag system is designed for them. Young children and infants need the protection that a child restraint system can provide. Always secure children properly in your vehicle. To read how, see the part of this manual called “Children.
How the Air Bag Systems Work Where are the air bags? The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side. The driver’s frontal air bag is in the middle of the steering wheel.
The driver’s side impact air bag is in the side of the driver’s seatback closest to the door. 1-26 The right front passenger’s side impact air bag is in the side of the passenger’s seatback closest to the door.
When should an air bag inflate? CAUTION: If something is between an occupant and an air bag, the bag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating air bag must be kept clear. Don’t put anything between an occupant and an air bag, and don’t attach or put anything on the steering wheel hub or on or near any other air bag covering. Don’t let seat covers block the inflation path of a side impact air bag.
In any particular crash, no one can say whether an air bag should have inflated simply because of the damage to a vehicle or because of what the repair costs were. For frontal air bags, inflation is determined by the angle of the impact and how quickly the vehicle slows down in frontal and near-frontal impacts. For side impact air bags, inflation is determined by the location and severity of the impact.
What will you see after an air bag inflates? After an air bag inflates, it quickly deflates, so quickly that some people may not even realize the air bag inflated. Some components of the air bag module -- the steering wheel hub for the driver’s air bag, the instrument panel for the right front passenger’s bag, the side of the seatback closest to the door for the driver and right front passenger’s side impact air bags -- will be hot for a short time.
In many crashes severe enough to inflate an air bag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger air bag. D Air bags are designed to inflate only once. After an air bag inflates, you’ll need some new parts for your air bag system. If you don’t get them, the air bag system won’t be there to help protect you in another crash. A new system will include air bag modules and possibly other parts.
Servicing Your Air Bag-Equipped Vehicle Rear Seat Passengers Air bags affect how your vehicle should be serviced. There are parts of the air bag systems in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag systems. To purchase a service manual, see “Service and Owner Publications” in the Index.
Lap-Shoulder Belt All three rear seating positions have lap-shoulder belts. Here’s how to wear one properly. 2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again. If the belt is not long enough, see “Safety Belt Extender” at the end of this section.
CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Rear Safety Belt Comfort Guides for Children and Small Adults Rear shoulder belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head. There is one guide for each of the outside passenger positions in the rear seat.
2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.
Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
CAUTION: (Continued) For example, in a crash at only 25 mph (40 km/h), a 12-lb. (5.5 kg) baby will suddenly become a 240-lb. (110 kg) force on a person’s arms. A baby should be secured in an appropriate restraint. CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby doesn’t weigh much -- until a crash. During a crash a baby will become so heavy it is not possible to hold it.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. CAUTION: Children who are up against, or very close to, any air bag when it inflates can be seriously injured or killed.
CAUTION: Newborn infants need complete support, including support for the head and neck. This is necessary because a newborn infant’s neck is weak and its head weighs so much compared with the rest of its body. In a crash, an infant in a rear-facing seat settles into the restraint, so the crash forces can be distributed across the strongest part of an infant’s body, the back and shoulders. Infants always should be secured in appropriate infant restraints.
Restraint Systems for Children An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous flat surface. Make sure that the infant’s head rests toward the center of the vehicle. 1-40 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint.
A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a five-point harness. A booster seat can also help a child to see out the window.
Q: A: How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner. For many years, add-on child restraints have used the adult belt system in the vehicle. To help reduce the chance of injury, the child also has to be secured within the restraint.
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General Motors, therefore, recommends that child restraints be secured in a rear seat outside position including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat. Never put a rear-facing child restraint in the front passenger seat.
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. If the child restraint does not have a top strap, one can be obtained, in kit form, for many child restraints. Ask the child restraint manufacturer whether or not a kit is available. In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored.
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle may have the LATCH system. If it does, you’ll find anchors (A) in the rear outside seat positions. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system will have two metal tabs where the seat cushion meets the seatback. Anchor brackets for the rear seat positions are located on the floor in the cargo area of your vehicle.
In order to use the system, you need either a forward-facing child restraint that has attaching points (B) at its base and a top tether anchor (C), or a rear-facing child restraint that has attaching points (B), as shown here. With this system, use the LATCH system instead of the vehicle’s safety belts to secure a child restraint.
CAUTION: If a LATCH-type child restraint isn’t attached to its anchorage points, the restraint won’t be able to protect a child sitting there. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchorage points, or use the vehicle’s safety belts to secure the restraint.
Securing a Child Restraint in a Rear Outside Seat Position You’ll be using the lap-shoulder belt. See the earlier part about the top strap if the child restraint has one. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. 1. Put the restraint on the seat. 2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint.
4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. If you’re using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 6. Push and pull the child restraint in different directions to be sure it is secure.
Center Seat Position Don’t use child restraints in this position. The restraints won’t work properly. 1-50 Securing a Child Restraint in the Right Front Seat Position Your vehicle has a right front passenger air bag. Never put a rear-facing child restraint in this seat.
CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating air bag. Always secure a rear-facing child restraint in the rear seat. Although a rear seat is a safer place, you can secure a forward-facing child restraint in the right front seat. You’ll be using the lap-shoulder belt.
4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-52 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. You may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pull the child restraint in different directions to be sure it is secure. To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger.
Older Children Q: A: What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. It should never be worn over the abdomen, which could cause severe or even fatal internal injuries in a crash.
CAUTION: Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. Q: What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? A: If the child is sitting in a seat next to a window, move the child toward the center of the vehicle.
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen. That could cause serious or fatal injuries. Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs.
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt isn’t long enough to fasten, your dealer will order you an extender. It’s free. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. The extender will be just for you, and just for the seat in your vehicle that you choose. Don’t let someone else use it, and use it only for the seat it is made to fit.
Section 2 Features and Controls Here you can learn about the many standard and optional features on your vehicle, and information on starting, shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is working properly -- and what to do if you have a problem.
Windows CAUTION: Leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows Express-Down Window The driver’s and front passenger’s window switches have an express-down feature that allows you to lower the window without holding the switch down. Press the bottom of the driver’s window switch down briefly to activate the express-down feature. Lightly tap the switch to open the window slightly. The express-down feature can be interrupted at any time by pressing the top of the switch.
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Don’t leave the keys in a vehicle with children.
This vehicle has one double-sided key for the ignition and door locks. It will fit with either side up. When a new vehicle is delivered, the dealer provides the owner with a pair of identical keys and a key code number. NOTICE: Your vehicle has a number of new features that can help prevent theft. But you can have a lot of trouble getting into your vehicle if you ever lock your key inside. You may even have to damage your vehicle to get in. So be sure you have an extra key.
Door Locks CAUTION: Unlocked doors can be dangerous. D Passengers -- especially children -- can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle won’t open it. You increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked. So, wear safety belts properly and lock the doors whenever you drive. D Young children who get into unlocked vehicles may be unable to get out.
Programmable Locking Feature Power Door Locks The power door lock switches are located on the driver’s and front passenger’s armrests. The following is the list of available programming options: D Mode 1: All doors lock when the transmission is shifted into gear. D Mode 2: All doors lock when the vehicle speed is greater than 8 mph (13 km/h). D Mode 3: No automatic door locking.
2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30 second program timer will begin. 3. You are now ready to program the automatic door locks. Select one of the three programming options listed above, and press the lock side of the power door lock switch to cycle through the lock options. You will have 30 seconds to begin programming.
To enter the program mode you need to do the following: 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold it there while you perform the next step. 2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30 second program timer will begin. 3. You are now ready to program the automatic door locks.
2. You will find a security lock lever located on the inside edge of each rear door. Move the lever down to engage the safety lock. Move the lever up to disengage the safety lock. If the power lock switch is pressed when a door is open and the key is in the ignition, all the doors will lock and then the driver’s door will unlock. Leaving Your Vehicle If you are leaving the vehicle, take your key, open your door and set the locks from inside. Then get out and close the door.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
Matching Transmitter(s) to Your Vehicle Battery Replacement Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. When the dealer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched.
To replace the battery in the remote keyless entry transmitter do the following: Liftgate/Liftglass CAUTION: 1. Insert a thin coin in the slot between the covers of the transmitter housing. Gently pry the transmitter apart. 2. Remove and replace the battery with a three-volt CR2032 or equivalent battery, positive (+) side down. 3. Align the covers and snap them together. It can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (CO) gas can come into your vehicle.
Liftgate Release Emergency Release for Opening Liftgate To unlock the liftgate, you may use the power door locks or the keyless entry system described earlier. 1. Remove the trim plug to expose the access hole in the trim panel. On some vehicles the liftglass will also unlock when the liftgate is unlocked. Use the pushbutton on the liftglass to open it. 2. Use a screwdriver to reach through the access hole in the trim panel.
Key in the Ignition Parking Lots If you leave your vehicle with the keys inside, it’s an easy target for joy riders or professional thieves -- so don’t do it. Even if you park in a lot where someone will be watching your vehicle, it’s still best to lock it up and take your keys.
Content Theft-Deterrent (If Equipped) Your vehicle may be equipped with a content theft-deterrent alarm system. United States Canada With this system, the SECURITY light will flash as you open the door (if your ignition is off). This light reminds you to activate the theft-deterrent system. Here’s how to do it: 1. Open the door. 2. Lock the door with the power door lock switch or the remote keyless entry transmitter. The SECURITY light should come on and stay on. 3. Close all doors.
Testing the Alarm The alarm can be tested by following these steps: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter. 3. Get out of the vehicle, close the door and wait for the SECURITY light to go out. 4. Then reach in through the window, unlock the door with the manual door lock and open the door. This should set off the alarm.
If the engine does not start after three tries, the vehicle needs service. If the engine is running and the SECURITY light comes on, you will be able to restart the engine if you turn the engine off. However, your Passlock system is not working properly and must be serviced by your dealer. Your vehicle is not protected by Passlock at this time. You may also want to check the fuse (see “Fuses and Circuit Breakers” in the Index). See your dealer for service.
Ignition Positions NOTICE: If your key seems stuck in LOCK and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? Turn the key only with your hand. Using a tool to force it could break the key or the ignition switch. If none of this works, then your vehicle needs service. B (Accessory): This position lets you use things like the radio and the windshield wipers when the engine is off. NOTICE: Use the key to turn the ignition switch to four different positions.
Retained Accessory Power (RAP) Your vehicle is equipped with a Retained Accessory Power (RAP) feature which will allow certain features of your vehicle to continue to work up to 20 minutes after the ignition key is turned to LOCK. Your radio, power windows, sunroof (option) and overhead console will work when the ignition key is in RUN or ACCESSORY. Once the key is turned from RUN to LOCK, these features will continue to work for up to 20 minutes or until a door is opened.
When starting your engine in very cold weather (below 0_F or -18_C), do this: 1. With your foot off the accelerator pedal, turn the ignition key to START and hold it there. When the engine starts, let go of the key. 2. If your engine still won’t start (or starts but then stops), it could be flooded with too much gasoline. Try pushing your accelerator pedal all the way to the floor and holding it there as you hold the key in START for about three seconds.
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the driver’s side of the engine compartment, behind the battery. 3. Plug it into a normal, grounded 110-volt AC outlet. CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet.
CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to PARK (P).
NEUTRAL (N): In this position, the engine doesn’t connect with the wheels. To restart when you’re already moving, use NEUTRAL (N) only. DRIVE (D): This position is for normal driving. If you need more power for passing, and you’re: D Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. CAUTION: D Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
FIRST (1): This position gives you even more power but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the selector lever is put in FIRST (1) while the vehicle is moving forward, the transmission won’t shift into first gear until the vehicle is going slowly enough. NOTICE: If your rear wheels can’t rotate, don’t try to drive. This might happen if you were stuck in very deep sand or mud or were up against a solid object. You could damage your transmission.
Four-Wheel Drive (If Equipped) If your vehicle has four-wheel drive, you can send your engine’s driving power to all four wheels for extra traction. To get the most satisfaction out of four-wheel drive, you must be familiar with its operation. Read the part that follows before using four-wheel drive. You should use two-wheel drive (2HI) for most normal driving conditions.
2HI: This setting is for driving in most street and highway situations. Your front axle is not engaged in two-wheel drive. It also provides the best fuel economy. A4WD: This setting is ideal for use when road conditions are variable. When driving your vehicle in A4WD, the front axle is engaged, but the vehicle’s power is sent to the rear wheels. When the vehicle senses a loss of traction, the system will automatically engage four-wheel drive.
If the SERVICE 4WD light on the instrument panel cluster stays on, you should take your vehicle to your dealer for service. See “Service 4WD” in the Index for further information. Shifting to 4HI or A4WD Turn the knob to 4HI or A4WD. This can be done at any speed and the indicator light will flash while shifting. It will remain illuminated when the shift is complete. Shifting to 2HI Turn the knob to 2HI. This can be done at any speed.
Shifting to NEUTRAL Shifting Out of NEUTRAL To shift the transfer case to NEUTRAL first make sure the vehicle is parked so that it will not roll: To shift the transfer case out of NEUTRAL: 1. Set the parking brake. 1. Set the parking brake and apply the regular brake pedal. 2. Start the vehicle. 2. Start the vehicle with the transmission in PARK (P). 3. Connect the vehicle to the towing vehicle. 4. Put the transmission in NEUTRAL (N). 3.
Parking Brake To set the parking brake, hold the regular brake pedal down with your right foot and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on. To release the parking brake, hold the regular brake pedal down. Pull the parking brake lever up until you can press in the button at the end of the lever. Hold the button in as you move the parking brake lever all the way down.
Shifting Into PARK (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, use the steps that follow.
Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. If you have four-wheel drive, your vehicle will be free to roll -- even if your shift lever is in PARK (P) -- if your transfer case is in NEUTRAL. So be sure the transfer case is in a drive gear -- not in NEUTRAL. See “Four-Wheel Drive (Automatic Transfer Case)” in the Index.
Shifting Out of PARK (P) Parking Over Things That Burn Your vehicle has an automatic transmission shift lock control system. You have to fully apply the regular brakes before you can shift from PARK (P) when the ignition is in RUN. See “Automatic Transmission Operation” in the Index. If you cannot shift out of PARK (P), ease pressure on the shift lever -- push the shift lever all the way into PARK (P) as you maintain brake application.
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can’t see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: D Your exhaust system sounds strange or different. D Your vehicle gets rusty underneath. D Your vehicle was damaged in a collision. D Your vehicle was damaged when driving over high points on the road or over road debris. D Repairs weren’t done correctly.
CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you’ve left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to PARK (P).
Tilt Wheel Turn Signal/Multifunction Lever You should adjust the steering wheel before you drive. The tilt lever is located on the driver’s side of the steering column, under the turn signal lever. You can raise it to the highest level to give your legs more room when you enter and exit the vehicle. The lever on the left side of the steering column includes the following: To tilt the wheel, hold the steering wheel and pull the lever toward you.
Turn and Lane Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically. An arrow on the instrument panel cluster will flash in the direction of the turn or lane change.
Headlamp High/Low-Beam Changer Flash-to-Pass Feature To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are in the automatic position. When the high beams are on, this indicator light on the instrument panel cluster will also be on.
Windshield Wipers : Mist : Off You control the windshield wipers by turning the band with the wiper symbol on it. For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time.
Windshield Washer There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer fluid on the windshield, press the paddle. The wipers will clear the window and then either stop or return to your preset speed. Rear Window Washer/Wiper This control is located to the right of the steering wheel on the instrument panel. CAUTION: In freezing weather, don’t use your washer until the windshield is warmed.
Cruise Control (If Equipped) With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). If you apply your brakes, the cruise control will shut off. CAUTION: D Cruise control can be dangerous where you : Off | : On + : Resume/Accelerate : Set D can’t drive safely at a steady speed.
Setting Cruise Control CAUTION: If you leave your cruise control switch on when you’re not using cruise, you might hit a button and go into cruise when you don’t want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. United States Canada The CRUISE light on the instrument panel cluster will illuminate when the cruise control is engaged. Resuming a Set Speed 1. Move the cruise control switch to on. 2. Get up to the speed you want.
Increasing Speed While Using Cruise Control Using Cruise Control on Hills There are two ways to go to a higher speed: How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control.
Exterior Lamps Your exterior lamps knob is on the driver’s side of your instrument panel. Turn the knob clockwise to the master lamps symbol to turn on all the lamps listed as well as the headlamps. Turn the knob all the way counterclockwise to this symbol to turn off the lamps and put the system in automatic headlamp mode.
There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor sees a change in lighting lasting longer than the delay. To idle your vehicle with the automatic headlamp system off, set the parking brake while the ignition is off.
To idle your vehicle with the DRL off, put your vehicle’s transmission in PARK (P). The DRL will stay off until you shift out of PARK (P). The following does not apply to vehicles sold in Canada. When necessary, you may turn off the automatic headlamp system and the Daytime Running Lamps (DRL) feature by following the steps below: 1. Turn the ignition to RUN. 2. Press the dome override button four times within six seconds.
Interior Lamps Brightness Control Press the knob located next to the exterior lamps knob to extend and turn it to make your instrument panel lights brighter. Turn the knob all the way up to turn on the interior lamps. Press the knob back into its stored position. Dome Lamp Override You can use the dome override button, located below the exterior lamps knob, to set the dome lamps to come on automatically when a door is opened, or to remain off. To turn the lamps off press the button.
Exit Lighting Dome Lamps With exit lighting, the interior lamps will come on when you remove the key from the ignition to help you see while exiting the vehicle. With the dome override button in the “out” position, these lights will stay on for a short period of time and then will go out. The dome lamps will come on when you open a door.
Mirrors Electrochromic Day/Night Rearview Mirror with Compass and OnStarR(If Equipped) There are three buttons for the OnStar system. See your dealer for more information on the system and how to subscribe to OnStar. See “OnStarR System” in the Index for more information about the services OnStar provides. Automatic Dimming Feature When turned on, an electrochromic mirror automatically dims to the proper level to minimize glare from any headlamps behind you after dark.
Compass Calibration Press and hold the on/off button down for nine seconds to activate the compass calibration mode. “CAL” will be displayed in the compass window on the mirror. The mirror can be calibrated in one of two ways: D Drive the vehicle in circles at 5 mph (8 km/h) or less until the display shows “CAL,” or D drive the vehicle on your everyday routine. (This method may take longer to calibrate). Compass Variance The mirror is set to zone eight upon leaving the factory.
Electrochromic Day/Night Rearview Mirror with Compass, Temperature and OnStarR There are three buttons for the OnStar system. See your dealer for more information on the system and how to subscribe to OnStar. See “OnStarR System” in the Index for more information about the services OnStar provides. Automatic Dimming Feature When turned on, an electrochromic mirror automatically dims to the proper level to minimize glare from any headlamps behind you after dark.
Compass Operation Compass Variance Press the on/off button once to turn the compass on or off. The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north.
3. Scroll through the zone numbers that appear in the compass/temperature window on the mirror by pressing the on/off button. Once you find your zone number, release the button. After about four seconds, the mirror will return to the compass and temperature display, and the new zone number will be set. Outside Mirrors Adjust your outside mirrors so you can see a little of the side of your vehicle. Fold the mirrors in before before entering a car wash. To do this, pull the mirrors in toward the vehicle.
Power Remote Control Mirrors (If Equipped) Convex Outside Mirror A convex mirror’s surface is curved so you can see more from the driver’s seat. CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right or left lane, you could hit a vehicle. Check your inside mirror or glance over your shoulder before changing lanes. Heated Outside Rearview Mirrors The control is located on the driver’s door.
Electrochromic Rearview Outside Mirror with Curb View Assist (If Equipped) If your vehicle has this feature, the driver’s outside mirror will adjust for the glare of the headlamps behind you. See “Electrochromic Day/Night Rearview Mirror with Compass and OnStarR” earlier in this section. If your vehicle is equipped with memory mirrors, it will also be capable of performing the curb view assist mirror function.
Storage Compartments Travel Note Recorder (If Equipped) Glove Box To open your glove box, pull the handle on the front of the glove box and lower the door. Overhead Console The overhead console includes sunglasses storage, a HomeLinkR transmitter and a travel note recorder (if equipped). The overhead console may also contain a travel note recorder. To record a message, press the button with the circle on it and begin speaking. Press the button with the circle on it again to stop recording.
To delete messages, press the button with the square on it while the message is playing. If you press and hold the right arrow button and the circle button at the same time for a half of a second, all of the messages will be deleted. For more information on these components, please see the Index for that item. Door Storage Convenience Net (If Equipped) You will find a storage compartment on each of the front doors.
Cargo Security Shade (If Equipped) To remove the cargo cover, do the following: If your vehicle has a cargo cover, you can use it to cover items in the cargo area of your vehicle. 1. Release the cover from the latch posts and carefully roll it back up. To install the cargo cover, do the following: 2. Compress one endcap and remove it from the pocket in the trim panel. 1. Align the endcap with the pocket in the trim panel located behind the rear seat. 2.
Cargo Tie Downs Rear Floor Stowage Lid There are five cargo tie downs in the rear of your vehicle that allow you to strap cargo in and keep it from moving. CAUTION: If the rear floor stowage lid isn’t secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure the rear floor stowage lid properly. Your vehicle has a rear floor stowage lid located in the rear cargo area that allows you to put items underneath it.
Luggage Carrier CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier -- like paneling, plywood, a mattress, and so forth -- the wind can catch it as you drive along. This can cause you to lose control. What you are carrying could be violently torn off, and this could cause you or other drivers to have a collision, and of course damage your vehicle. You may be able to carry something like this inside.
To prevent damage or loss of cargo as you’re driving, check now and then to make sure the luggage carrier is locked and cargo is still securely fastened. Ashtrays and Cigarette Lighter The front ashtray is removable and fits into the front cupholder. NOTICE: Don’t hold a cigarette lighter in with your hand while it is heating. If you do, it won’t be able to back away from the heating element when it’s ready. That can make it overload, damaging the lighter and the heating element.
Accessory Power Outlets With the accessory power outlets, you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle has three accessory power outlets. The first outlet is located to the right of the cigarette lighter on the instrument panel. The second outlet is located on the rear of the center console, and the third one is located in the rear of the vehicle near the liftgate. Remove the cover from the outlet to use the outlet.
OnStarR System (If Equipped) OnStar is a vehicle communications system that offers a variety of services and provides a hands-free communication link between you and the OnStar Center. A service subscription agreement and fee are required in order to receive OnStar service. Services are available 24 hours a day, 7 days a week. For more information, call 1-888-ONSTAR-7 (1-888-667-8277). OnStar Services Button: Press this button once to contact an advisor who will be able to assist you with these services.
Volume Control: You can control the volume of the OnStar System using either the volume control knob on the radio or using the steering wheel volume control (if equipped). Telltale Light: This light will indicate the status of the system. A solid green light will come on when you start the vehicle to let you know that the system is on and is ready to make or receive calls. If the light blinks green it means that an incoming or outgoing call is in progress.
OnStar MED-NET: Med-Net can store your personal medical history and provide it to emergency personnel if necessary. (Requires activation and additional fee.) Remote Door Unlock: To contact the center, call 1-888-4-ONSTAR. You will be required to provide your security information. An advisor will send a command to your vehicle to unlock itself. The advisor can delay unlocking your vehicle. Remote Door Unlock is disabled 48 hours after the vehicle is parked to maintain the battery charge.
OnStar System Limitations Complete limitations can be found on the Subscriber Services Agreement. OnStar Service is: D available in the 48 contiguous United States, Alaska, Hawaii and Canada; D available when the vehicle is within the operating range of a cellular provider; D subject to limitations caused by atmospheric conditions, such as severe weather or topographical conditions, such as mountainous terrain; D subject to cellular carrier equipment limitations.
HomeLinkR Transmitter (If Equipped) Changes and modifications to this system by other than an authorized service facility could void authorization to use this equipment. Programming the HomeLink Transmitter Do not use the HomeLink Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. Be sure that people and objects are clear of the garage door you are programming.
3. When the HomeLink indicator light begins to blink slowly (this may take up to 30 seconds), hold the hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from HomeLink and then press and hold the transmit button on the hand-held transmitter. Continue to hold both buttons until the indicator light on HomeLink begins to flash rapidly (this may take up to 90 seconds).
3. Return to HomeLink in your vehicle and firmly press and release the programmed HomeLink button three times. The rolling-code garage door opener should now recognize HomeLink. You may either use HomeLink or the hand-held transmitter to open the garage door. If after following these instructions, you still have problems training the garage door opener, contact the manufacturer of HomeLink at 1-800-355-3515, or on the internet at www.homelink.com.
The Instrument Panel -- Your Information System 2-70
The main components of your instrument panel are the following: A. Exterior Lamp Controls I. Comfort Controls B. Air Vents J. Hood Release C. Turn Signal/Multifunction Lever K. Ashtray D. Instrument Panel Cluster L. Shift Lever E. Ignition Switch M. Lighter F. Transfer Case Controls (If Equipped) or Traction Control Button (If Equipped) N. Accessory Power Outlet G. Rear Window Washer/Wiper P. Glove Box O. Rear Window Defogger H.
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel you’ve used, and many other things you’ll need to know to drive safely and economically.
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). The odometer mileage can be checked without the vehicle running. Simply press the trip odometer button. You may wonder what happens if your vehicle needs a new odometer installed.
Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions.
Air Bag Readiness Light There is an air bag readiness light on the instrument panel, which shows the air bag symbol. The system checks the air bag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the air bag sensors, the air bag modules, the wiring and the crash sensing and diagnostic module. For more information on the air bag system, see “Air Bag” in the Index.
Charging System Indicator Light The charging system light will come on briefly when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system. It could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. Driving while this light is on could drain your battery.
Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left at an idle for an extended period. This condition is normal since the charging system is not able to provide full power at engine idle. As engine speeds are increased, this condition should correct itself as higher engine speeds allow the charging system to create maximum power. You can only drive for a short time with the reading in either warning zone.
This light should come on briefly when you turn the ignition key to RUN. If it doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See “Towing Your Vehicle” in the Index.
Engine Coolant Temperature Gage United States Canada This gage shows the engine coolant temperature. If the gage pointer moves into the red area, it means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.
This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The SERVICE ENGINE SOON or CHECK ENGINE light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle.
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light doesn’t come on, have it repaired. This light will also come on during a malfunction in one of two ways: D Light Flashing -- A misfire condition has been detected. A misfire increases vehicle emissions and may damage the emission control system on your vehicle. Dealer or qualified service center diagnosis and service may be required.
Did you just drive through a deep puddle of water? Emissions Inspection and Maintenance Programs If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.
Oil Pressure Gage CAUTION: Don’t keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. United States Canada The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals).
Change Engine Oil Light United States Security Light Canada This light is displayed when the engine oil needs to be changed. Once the engine oil has been changed, the CHANGE ENG OIL light must be reset. Until it is reset, the light will be displayed when the engine is on. For more information on resetting the system, see “Oil Life System” in the Index. United States Canada This light will come on briefly when you turn the key toward START. The light will stay on until the engine starts.
Cruise Control Light (If Equipped) United States Canada The CRUISE light appears whenever you set your cruise control. See “Cruise Control” in the Index. Reduced Engine Power United States Canada This light is displayed when a noticeable reduction in the vehicle’s performance may occur. The vehicle may be driven at a reduced speed when the reduced engine power light is on but acceleration and speed may be reduced. The performance may be reduced until the next time you drive your vehicle.
Service Four-Wheel-Drive Warning Light (If Equipped) Check Gages Light United States United States This light should come on briefly when you turn on the ignition, as a check to show you it is working. The SERVICE 4WD light comes on to indicate that there may be a problem with the drive system and service is required. Malfunctions can be indicated by the system before any problem is apparent, which may prevent serious damage to the vehicle.
Gate Ajar United States Fuel Gage Canada If this light comes on, your liftgate or liftglass is ajar. Try closing the liftgate or liftglass again. Never drive with the liftgate or liftglass even partially open. United States Canada When the ignition is on, the fuel gage tells you about how much fuel you have remaining.
Here are four things that some owners ask about. None of these show a problem with your fuel gage: Low Fuel Light D At the gas station, the gas pump shuts off before the gage reads full. D It takes a little more or less fuel to fill up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to fill the tank. D The gage moves a little when you turn a corner or speed up.
Driver Information Center (DIC) (If Equipped) The DIC display is located on the instrument panel cluster above the steering wheel. The DIC can display information such as the trip odometer, fuel economy and personalization features. DIC Operation and Displays The DIC comes on when the ignition is on. After a short delay the DIC will display the current driver and the information that was last displayed before the engine was turned off. If a problem is detected, a warning message will appear on the display.
Odometer Timer Press the trip information button until the odometer appears on the display. This shows the total distance the vehicle has been driven in either miles or kilometers. Pressing the reset stem located on the instrument cluster with the vehicle off will also display the odometer. The DIC can be used as a stopwatch. Press the select button while TIMER is displayed to start the timer.
Fuel Range Instant Fuel Economy Press the fuel information button until RANGE appears to display the remaining distance you can drive without refueling. It’s based on fuel economy and the fuel remaining in the tank. The display will show LOW if the fuel level is low. Press the fuel information button until INST appears in the display. Instant fuel economy is how many miles per gallon your vehicle is at the particular moment in time. The instant fuel economy cannot be reset.
The DIC does not replace the need to maintain your vehicle as recommended in the Maintenance Schedule in this manual. Also, the oil change reminder will not detect dusty conditions or engine malfunctions that may affect the oil. If you drive in dusty areas, change your oil after every 3,000 miles (5 000 km) or three months, whichever occurs first, unless the DIC instructs you to do so sooner. Also, the oil change reminder does not measure how much oil you have in your engine.
Alarm Warning Type Press the personalization button until ALARM WARNING TYPE appears in the display. To select your personalization for alarm warning type, press the select button while ALARM WARNING TYPE is displayed on the DIC. Pressing the select button will scroll through the following choices: D ALARM WARNING: BOTH (default) D ALARM WARNING: OFF D ALARM WARNING: HORN D ALARM WARNING: LAMPS If you choose BOTH, the headlamps will flash and the horn will chirp when the alarm is active.
Automatic Unlocking Press the personalization button until AUTOMATIC UNLOCKING appears in the display. To select your personalization for automatic unlocking, press the select button while AUTOMATIC UNLOCKING is displayed on the DIC.
Choose one of the three options and press the personalization button while it is displayed on the DIC to select it and move on to the next feature. For more information on seat position recall see “Memory Seat and Mirrors” in the Index. Perimeter Lighting Press the personalization button until PERIMETER LIGHTING appears in the display. To select your personalization for perimeter lighting, press the select button while PERIMETER LIGHTING is displayed on the DIC.
If you choose lamps, the parking lamps will flash each time you press the button with the lock symbol on the remote keyless entry transmitter. If you choose lamps, the parking lamps will flash each time you press the button with the unlock symbol on the remote keyless entry transmitter. Choose one of the four options and press the personalization button while it is displayed on the DIC to select it and move on to the next feature.
Headlamps on at Exit Tilt Mirror in Reverse (If Equipped) Press the personalization button until HEADLAMPS ON AT EXIT appears in the display. To select your personalization for how long the headlamps will stay on when you turn off the vehicle, press the select button while HEADLAMPS ON AT EXIT is displayed on the DIC. Pressing the select button will scroll through the following choices: Press the personalization button until TILT MIRROR IN REVERSE appears in the display.
Choose one of the four options and press the personalization button while it is displayed on the DIC to select it and move on to the next feature. For more information on tilt mirror in reverse see “Curb View Assist Mirror” in the Index. Easy Exit Seat (If Equipped) Press the personalization button until EASY EXIT SEAT appears in the display. To select your personalization for seat position exit, press the select button while SEAT POSITION EXIT is displayed on the DIC.
Display Language To select your personalization for display language, press the select button while DISPLAY LANGUAGE is displayed on the DIC. Pressing the select button will scroll through the following languages: D D D D D D D D English French Spanish If you accidentally choose a language that you don’t want or understand, press and hold the personalization button and the trip information button and the same time. The DIC will begin scrolling through the languages in their particular language.
DIC Warnings and Messages Warning messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. More than one message may appear at one time, they will appear one behind the other. Some messages may not require immediate action but you should press the select button to acknowledge that you received the message and clear it from the display.
SERVICE AIR BAG REAR ACCESS OPEN If there is a problem with the air bag system this message will be displayed on the DIC. Have a qualified technician inspect the system for problems. Pressing the select button will acknowledge this message and clear it from the DIC display. If the liftgate or liftglass is open while the ignition is in RUN, this message will appear on the DIC and you will hear a chime. Turn off the vehicle and check the liftgate and liftglass.
CHECK OIL LEVEL ICE POSSIBLE If the oil level in the vehicle is low this message will appear on the DIC. Check the oil level and correct it as necessary. You may need to need to let the vehicle cool or warm up and cycle the ignition to be sure this message will clear. Once the problem is corrected, pressing the select button will clear this message from the DIC display. If the outside temperature reaches a level where ice could form on the roadway, this message may appear on the DIC.
LEFT REAR DOOR AJAR RFA # BATTERY LOW If the driver’s side rear door is not fully closed this message will appear on the display and you will hear a chime. Stop and turn off the vehicle, check the door for obstacles, and close the door again. Check to see if the message still appears on the DIC. Pressing the select button will acknowledge this message and clear it from the DIC display. If a remote keyless entry transmitter battery is low this message will appear on the DIC.
Section 3 Comfort Controls and Audio Systems In this section, you’ll find out how to operate the comfort control and audio systems offered with your vehicle. Be sure to read about the particular systems supplied with your vehicle.
Comfort Controls Manual Dual Zone Comfort Controls This section tells you how to use the comfort controls. With these systems, you can control the heating, cooling and ventilation in your vehicle. Comfort Controls Personalization (If Equipped) If your vehicle is equipped with the automatic comfort control system and memory seats and mirrors, you can store and recall the climate control settings for temperature, air delivery mode and fan speed for two different drivers.
Driver’s Side Temperature Lever Mode Knob The lever on the left side of the climate control panel is used to adjust the air temperature on the driver’s side, independent of the temperature set by the passenger. Slide the lever upward to raise the temperature. Slide the lever downward to lower the temperature.
Mode Buttons (Recirculation): Press this button to limit the amount of outside air entering your vehicle. This is helpful when you are trying to limit odors entering your vehicle and for maximum air conditioning performance in hot weather. Recirculation cannot be used in floor, blend or defrost modes. An indicator on the button will light up, flash three times and turn off when recirculation is selected in these modes.
Driver’s Side Temperature Knob The driver’s side knob is used to adjust the temperature of the air coming through the system on the driver’s side. Turn the knob counterclockwise to lower the cabin temperature. The display will show the temperature decreasing as you turn the knob counterclockwise. Turn the knob clockwise to increase the cabin temperature. The display will show the temperature increasing as you turn the knob clockwise.
Automatic Operation Press the AUTO button to set the system to automatically control the air delivery mode, fan speed, air temperature and recirculation operations. Whenever you press AUTO, the display will change to show the current driver’s set temperature, automatic air delivery mode and fan speed. Press the AUTO button again within five seconds and the display will show the passenger’s set temperature. After five seconds the display will change to the EXT (external) temperature outside the vehicle.
Manual Operation You may manually adjust the air delivery mode or fan speed. Use the mode button to cycle through the following four air delivery modes: (Panel): This setting will deliver air to the instrument panel outlets. (Bi-Level): This setting will deliver warmer air to the floor and cooler air to the instrument panel outlets. (Floor): This setting will deliver air to the floor outlets. (Defog): This setting will deliver air to the floor and windshield outlets.
Air Conditioning Heating On hot days, open the windows long enough to let hot inside air escape. This reduces the time it takes for your vehicle to cool down. Then keep your windows closed for the air conditioner to work its best. If you have the manual system, on cold days use floor with the temperature lever in the red area. If you have the automatic system, press AUTO and adjust the temperature by turning the temperature knob clockwise or counterclockwise.
If your vehicle has the automatic system and you select FRONT defrost or defog from AUTO, the system will control the fan speed. Adjust the temperature and fan speed to your comfort level. After the windshield is clear, adjust the temperature to your normal setting and select the AUTO button and return to AUTO mode and fan control. For maximum front defrost performance under extreme icing or frosting conditions, increase the temperature setting to 90_F (32_C) and increase the fan speed to high.
Rear Comfort Controls Your vehicle has one of the following rear comfort control systems. With either system, the rear comfort controls will be disabled when the front comfort control system is in defrost. This occurs to provide maximum airflow to clear the windshield. The temperature of the air coming through the rear outlets is determined by the front passenger’s temperature setting. Press the PWR button to turn the rear comfort controls on and off.
Ventilation System For mild outside temperatures when little heating or cooling is needed, use the panel outlet setting (on the manual system) to direct outside air through your vehicle. Air will flow through the instrument panel outlets. Your vehicle’s flow-through ventilation system supplies outside air into the vehicle when it’s moving. When the vehicle is not moving, you can get outside air to flow through by selecting any air delivery mode and any fan speed.
Ventilation Tips D Keep the hood and front air inlet free of ice, snow or any other obstruction such as leaves. The heater and defroster will work better, reducing the chance of fogging your windows. D In cool damp weather, minimize your use of recirculation to reduce the chance of fogging your windows. Comfort Control Steering Wheel Controls (If Equipped) If your vehicle has this feature, you can control certain comfort control functions using the buttons on your steering wheel.
Audio Systems Your audio system has been designed to operate easily and give years of listening pleasure. You will get the most enjoyment out of it if you acquaint yourself with it first. Find out what your audio system can do and how to operate all its controls, to be sure you’re getting the most out of the advanced engineering that went into it.
AUTO VOL: Your system has a feature called Speed-Compensated Volume (SCV). With SCV, your audio system adjusts automatically to make up for road and wind noise as you drive. Set the volume at the desired level. Press AUTO VOL to adjust the SCV. AVOL will appear on the display. Each time you press AUTO VOL, another volume setting (LOW, MEDIUM, HIGH or OFF) will appear on the display. The volume level should always sound the same to you as you drive.
Setting Preset Stations Setting the Tone (Bass/Treble) The six numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2) by performing the following steps: P-TYPE LIST AUDIO: To adjust the bass, press and release the P-TYPE LIST AUDIO control until BASS appears on the display. Then turn the control clockwise to increase bass and counterclockwise to decrease bass. The display will show the bass level. 1. Turn the radio on. 2.
To set treble to the middle position, press and hold the P-TYPE LIST AUDIO control. The radio will produce one beep and set the display level to the middle position. To set all tone and speaker controls to the middle position, press and hold the P-TYPE LIST AUDIO control when no tone or speaker control is active. The radio will produce one beep and display ALL with the level display in the middle position. When you use this control, the radio’s AUTO TONE setting will return to manual.
The middle position balances the sound between the speakers. To set the fade to the middle position, press the P-TYPE LIST AUDIO control briefly, then press it again and hold it until the radio emits one beep. The fade will be set to the middle position and the display will show the speaker balance. To set all tone and speaker controls to the middle position, press and hold the P-TYPE LIST AUDIO control when no tone or speaker control is active.
Accessing RDS Stations To access RDS stations perform the following steps: 1. Push the SEEK TYPE button or turn the P-TYPE LIST AUDIO control to display the program type list. 2. Turn the control either clockwise or counterclockwise to select a program type. The list is alphabetical. If you select ANY TYPE your radio will seek to the first PTY available. 3. Push the SEEK TYPE button to activate search. VOL PWR: Turn this control clockwise to increase volume when RDS interrupts regular play.
RDS Radio Announcements (Alert): Alert warns of national or local emergencies. You will not be able to turn off alert announcements. ALERT! appears on the display when an alert announcement plays. When an alert announcement comes on the tuned radio station, you will hear it, even if the volume is muted or a cassette tape or compact disc is playing. If the cassette tape or compact disc player is playing, play will stop for the announcement and resume when the announcement is finished.
When a traffic announcement comes on the tuned radio station, you will hear it, even if the volume is muted or a cassette tape or compact disc is playing. The TRAF icon and TRAFFIC will appear on the display while the traffic announcement plays. If the cassette tape or compact disc player was being used, the tape or compact disc will stay in the player and resume play at the point where it stopped.
2 NEXT: Press this button to go to the next selection on the tape. If you press the button more than once, the player will continue moving forward through the tape. SEEK and a positive number will appear on the display. Your tape must have at least three seconds of silence between each selection for 2 NEXT to work. To forward through each selection press the right SEEK PSCAN arrow. The sound will mute while seeking. 3 REV: Press this button to reverse the tape rapidly.
TAPE AUX: With a cassette tape in the player and the radio playing, press this button to play a cassette tape. Press AM FM to return to the radio when a cassette tape is playing. The inactive tape will remain safely inside the radio for future listening. EJT: Press this button to remove a tape. The radio will play. Eject may be activated with the radio off. Cassette tapes may be loaded with the radio off if this button is pressed first.
Radio/Cassette Tape Messages (CAL ERR): This message is displayed when the radio has not been calibrated properly for the vehicle. You must return to the dealership for service. (LOCKED): This message is displayed when the THEFTLOCKR system has locked up. You must return to the dealership for service. (CHK TAPE): If CHK TAPE appears on the radio display, the tape won’t play because of one of the following errors. (CLEAN): If this message appears on the display, the cassette tape player needs to be cleaned.
AM-FM Stereo with Compact Disc Player with Radio Data System (RDS) and Automatic Tone Control (If Equipped) AUTO VOL: Your system has a feature called Speed-Compensated Volume (SCV). With SCV, your audio system adjusts automatically to make up for road and wind noise as you drive. Set the volume at the desired level. Press AUTO VOL to adjust the SCV. AVOL will appear on the display. Each time you press AUTO VOL, another volume setting (LOW, MEDIUM, HIGH or OFF) will appear on the display.
A " SEEK PSCAN : To seek, press the right arrow to tune to the next station and the left arrow to tune to the previous station and stay there. To scan your preset stations, press and hold one of the arrows for more than two seconds. The radio will produce one beep. Use preset scan to listen to each of your favorite stations stored on your pushbuttons for a few seconds. The radio will scan through each of the stations stored on your pushbuttons, except those stations with weak reception.
Setting the Tone (Bass/Treble) P-TYPE LIST AUDIO: To adjust the bass, press and release the P-TYPE LIST AUDIO control until BASS appears on the display. Then turn the control clockwise to increase bass and counterclockwise to decrease bass. The display will show the bass level. To set the bass to the middle position, press and hold the P-TYPE LIST AUDIO control. The radio will produce one beep and set the display level to the middle position.
Adjusting the Speakers (Balance/Fade) To adjust the balance, press and release the P-TYPE LIST AUDIO control until BAL appears on the display. Turn the control clockwise to move the sound to the right speakers and counterclockwise to move the sound to the left speakers. The middle position balances the sound between the speakers. To set the fade to the middle position, press the P-TYPE LIST AUDIO control briefly, then press it again and hold it until the radio emits one beep.
RDS features are only available on FM stations which broadcast RDS information. The RDS features of your radio rely on receiving specific RDS information from these stations. These features will only work when the RDS information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, please contact the radio station.
AM FM: The AM FM button operates the alternate frequency feature. This feature allows the radio to switch automatically to a stronger station with the same programming. Alternate frequency is off by default from the factory. Press and hold AM FM for two seconds to turn alternate frequency on or off. AF ON or AF OFF will appear on the display and the radio will beep once. The radio will not switch automatically to other stations when alternate frequency is off.
Your radio can be programmed to interrupt the playback of a cassette tape, CD or FM radio by enabling the traffic interrupt feature. Press the TRAF button once to seek to an RDS station that supports the traffic interrupt feature if the current tuned station does not. The TRAF icon will flash on the display when seeking for a station that supports traffic interrupt. When the traffic interrupt feature is on, TRAF will appear on the display.
4 FWD: Press and hold this button to advance quickly within a track. Press and hold this button for less than two seconds to advance at six times the normal playing speed. Press and hold it for more than two seconds to advance at 17 times the normal playing speed. Release it to play the passage. The display will show ET and the elapsed time. TUNE DISP: Press this control to see how long the current track has been playing. ET and the elapsed time will appear on the display.
Radio/Compact Disc Messages (CAL ERR): This message is displayed when the radio has not been calibrated properly for the vehicle. You must return to the dealership for service. AM-FM Stereo with Cassette Tape and Compact Disc Player with Radio Data System (RDS) and Automatic Tone Control (If Equipped) (LOCKED): This message is displayed when the THEFTLOCKR system has locked up. You must return to the dealership for service.
AUTO VOL: Your system has a feature called Speed-Compensated Volume (SCV). With SCV, your audio system adjusts automatically to make up for road and wind noise as you drive. Set the volume at the desired level. Press AUTO VOL to adjust the SCV. AVOL will appear on the display. Each time you press AUTO VOL, another volume setting (LOW, MEDIUM, HIGH or OFF) will appear on the display. The volume level should always sound the same to you as you drive.
Setting Preset Stations Setting the Tone (Bass/Treble) The six numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2) by performing the following steps: P-TYPE LIST AUDIO: To adjust the bass, press and release the P-TYPE LIST AUDIO control until BASS appears on the display. Then turn the control clockwise to increase bass and counterclockwise to decrease bass. The display will show the bass level. 1. Turn the radio on. 2.
To set all tone and speaker controls to the middle position, press and hold the P-TYPE LIST AUDIO control when no tone or speaker control is active. The radio will produce one beep and display ALL with the level display in the middle position. When you use this control, the radio’s AUTO TONE setting will return to manual. AUTO TONE: This feature allows you to choose preset bass and treble equalization settings designed for rock, news, pop, jazz, classical and country stations.
To set all tone and speaker controls to the middle position, press and hold the P-TYPE LIST AUDIO control when no tone or speaker control is active. The radio will produce one beep and display ALL with the level display in the middle position. To adjust the fade, press and release the P-TYPE LIST AUDIO control until FADE appears on the display. Turn the control clockwise to move the sound to the front speakers and counterclockwise to move the sound to the rear speakers.
When you are tuned to an RDS station, the station name will appear on the display, instead of the frequency. Most RDS stations provide their station name, the time of day and a Program Type (PTY) for their current programming. Some stations also provide the name of the current program. TUNE DISP: Press this control to change what appears on the display while using RDS. Pressing this control will also display an RDS station frequency or program type when the radio is on.
RDS Radio Announcements (Alert): Alert warns of national or local emergencies. You will not be able to turn off alert announcements. ALERT! appears on the display when an alert announcement plays. When an alert announcement comes on the tuned radio station, you will hear it, even if the volume is muted or a cassette tape or compact disc is playing. If the cassette tape or compact disc player is playing, play will stop for the announcement and resume when the announcement is finished.
When a traffic announcement comes on the tuned radio station, you will hear it, even if the volume is muted or a cassette tape or compact disc is playing. The TRAF icon and TRAFFIC will appear on the display while the traffic announcement plays. If the cassette tape or compact disc player was being used, the tape or compact disc will stay in the player and resume play at the point where it stopped.
2 NEXT: Press this button to go to the next selection on the tape. If you press the button more than once, the player will continue moving forward through the tape. SEEK and a positive number will appear on the display. Your tape must have at least three seconds of silence between each selection for next to work. To forward through each selection press the right SEEK PSCAN arrow. The sound will mute while seeking. 3 REV: Press this button to reverse the tape rapidly.
Cassette Tape Messages (CHK TAPE): If CHK TAPE appears on the radio display, the tape won’t play because of one of the following errors. D The tape is tight and the player can’t turn the tape hubs. Remove the tape. Hold the tape with the open end down and try to turn the right hub counterclockwise with a pencil. Turn the tape over and repeat. If the hubs do not turn easily, your tape may be damaged and should not be used in the player. Try a new tape to make sure your player is working properly.
Playing a Compact Disc Insert a disc partway into the slot, label side up. The player will pull it in and the disc should begin playing. The display will show the CD symbol. If you want to insert a compact disc with the ignition off, first press TUNE DISP or EJT. If an error appears on the display, see “Radio/Compact Disc Messages” later in this section. 1 PREV: Press this button or the left SEEK PSCAN arrow to go to the previous track if the current selection has been playing for less than eight seconds.
TUNE DISP: Press this control to see how long the current track has been playing. ET and the elapsed time will appear on the display. To change what is normally shown on the display (track or elapsed time), press the control until you see the display you want, then hold the control for two seconds. The radio will produce one beep. Compact Disc Messages AM FM: Press this button to play the radio when a disc is in the player. The disc will stop but remain in the player. D The disc is upside down.
AM-FM Stereo with 6-Disc Compact Disc Player with Programmable Equalization and Radio Data System (RDS) (If Equipped) Standard radio--BoseR not shown 3-44 Playing the Radio VOLUME PWR: Press this control to turn the system on and off. To increase volume, turn the control clockwise. Turn it counterclockwise to decrease volume. AUTO VOL: Your system has a feature called automatic volume. With this feature, your audio system adjusts automatically to make up for road and wind noise as you drive.
Finding a Station Setting Preset Stations AM FM: Press this button to switch between AM, FM1 and FM2. The display shows your selection. The six numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six AM, six FM1 and six FM2) by performing the following steps: TUNE RCL P-TYPE: Turn this control to select radio stations. tSEEK SCANu: To seek, press the right or left arrow 1. Turn the radio on. briefly to go to the next or previous station and stay there.
Setting the Tone (Bass/Treble) AUDIO: To set the bass, press the AUDIO control until BASS appears on the display. Turn the control to increase or decrease bass. When you use this control, the radio’s tone setting will switch to custom. To set the treble, press the AUDIO control until TREB appears on the display. Turn the control to increase or decrease treble. When you use this control, the radio’s tone setting will switch to custom. If a station is weak or noisy, you may want to decrease the treble.
If your vehicle has the Bose radio, your audio system allows you to choose from four different equalization settings: talk, driver, normal and spatial. These settings can be used while listening to the radio or the CD player. Press the AUTO EQ button to scroll through your choices. Select TALK when listening to non-musical material such as news, talk shows, sports broadcasts and books on tape. This settings makes spoken words sound very clear.
Using RDS Your audio system is equipped with a Radio Data System (RDS). RDS mode gives you many useful new features. With RDS, the radio can do the following: D Seek only to stations with the types of programs you want to listen to, D seek to stations with traffic announcements, D receive announcements concerning local and national emergencies, and D receive and display messages from radio stations. RDS features are only available for use on FM stations which broadcast RDS information.
Setting PTY Preset Stations The six numbered pushbuttons let you return to your favorite Program Types (PTYs). These buttons have factory PTY presets. You can set up to 12 PTYs (six FM1 and six FM2) by performing the following steps: 1. Press AM FM to select FM1 or FM2. 2. Press P-TYPE, if it is not already on. 3. Turn the TUNE RCL P-TYPE control to select a PTY. 4. Press and hold one of the six numbered pushbuttons until you hear a beep.
Playing a Compact Disc LOAD CD : Press this button to load CDs into the compact disc player. This compact disc player will accommodate up to six discs. To insert one disc do the following: 1. Turn the ignition on. 2. Press and release the LOAD CD button. 3. Wait for the light, located to the right of the slot, to turn green. 4. Load a disc. Insert a disc partway into the slot, label side up. The player will pull the disc in. When the disc is inserted, the CD symbol will be displayed.
Playing a Specific Loaded Compact Disc For every CD loaded, a number will appear on the radio display. To play a specific CD, first press the CD AUX button to start playing a CD. Then press the numbered pushbutton that corresponds to the CD you want to play. A small bar will appear under the CD number that is playing, and the track number will appear. If an error appears on the radio display, see “Compact Disc Messages” later in this section.
RPT: With repeat, you can repeat one track or an entire disc. To use repeat, do the following: D To repeat the track you are listening to, press and release the RPT button. RPT will appear on the display. Press RPT again to turn it off. D To repeat the disc you are listening to, press and hold the RPT button for two seconds. RPT will appear on the display. Press RPT again to turn if off.
TUNE RCL P-TYPE: Press this control to see how long the current track has been playing. To change what is normally shown on the display (track or elapsed time), press the control until you see the display you want, then hold the control until the display flashes. AM FM: Press this button to play the radio when a disc is in the player. Using Song List Mode The integrated 6-disc CD changer has a feature called song list. This feature is capable of saving 20 track selections. 4.
4. Press and hold the SONG LIST button for two seconds. When pressing SONG LIST one beep will be heard immediately. After two seconds of pressing the SONG LIST button continuously, two beeps will be heard to confirm that the track has been deleted. After a track has been deleted, the remaining tracks are moved up the list. When another track is added to the song list, the tracks will be added to the end of the list. To delete the entire SONG LIST perform the following steps: 1. Turn the disc player on. 2.
Rear Seat Audio (If Equipped) This feature is intended for rear seat passengers. The following functions are controlled by the rear seat audio system buttons: PWR: Press this button to turn the rear seat audio system on or off. The rear speakers will be muted when the power is turned on unless you have a BoseR equipped vehicle. You may operate the rear seat audio functions even when the primary radio power is off. VOL: Turn the knob clockwise to increase volume and counterclockwise to decrease volume.
The SEEK button is inactive if the AM FM mode on the front radio is in use. While listening to a cassette tape, press the SEEK button to hear the next selection on the tape. Press and hold the SEEK button to go to the other side of the tape. The SEEK button is inactive if the tape mode on the front radio is in use. Audio Steering Wheel Controls (If Equipped) If your vehicle has this feature, certain radio functions can be operated by using the controls on your steering wheel.
Understanding Radio Reception To help avoid hearing loss or damage do the following: AM D Adjust the volume control to the lowest setting. D Increase volume slowly until you hear comfortably The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other. AM can pick up noise from things like storms and power lines. Try reducing the treble to reduce this noise if you ever get it.
Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes or a damaged mechanism. Cassette tapes should be stored in their cases away from contaminants, direct sunlight and extreme heat. If they aren’t, they may not operate properly or may cause failure of the tape player. Your tape player should be cleaned regularly after every 50 hours of use.
If your vehicle is equipped with the AM-FM Stereo with Cassette Tape and Compact Disc Player with Radio Data System (RDS) and Automatic Tone Control: 1. Turn the ignition to RUN or ACCESSORY. 2. Turn the radio off. 3. Press and hold the TAPE CD button for five seconds. READY will appear on the display and a cassette icon will flash for five seconds. 4. Insert the scrubbing action cleaning cassette. 5. Eject the cleaning cassette after the manufacturer’s recommended cleaning time.
Care of Your Compact Discs Fixed Mast Antenna Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge. The fixed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, you can straighten it out by hand.
Section 4 Your Driving and the Road Here you’ll find information about driving on different kinds of roads and in varying weather conditions. We’ve also included many other useful tips on driving.
Defensive driving really means “be ready for anything.” On city streets, rural roads or freeways, it means “always expect the unexpected.” Assume that pedestrians or other drivers are going to be careless and make mistakes. Anticipate what they might do. Be ready for their mistakes. Rear-end collisions are about the most preventable of accidents. Yet they are common. Allow enough following distance. It’s the best defensive driving maneuver, in both city and rural driving.
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It’s the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: D D D D Judgment Muscular Coordination Vision Attentiveness. Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving.
Since alcohol is carried in body water, this means that a woman generally will reach a higher BAC level than a man of her same body weight when each has the same number of drinks. The law in an increasing number of U.S. states, and throughout Canada, sets the legal limit at 0.08 percent. In some other countries, the limit is even lower. For example, it is 0.05 percent in both France and Germany. The BAC limit for all commercial drivers in the United States is 0.04 percent. The BAC will be over 0.
The body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. “I’ll be careful” isn’t the right answer. What if there’s an emergency, a need to take sudden action, as when a child darts into the street? A person with even a moderate BAC might not be able to react quickly enough to avoid the collision. There’s something else about drinking and driving that many people don’t know.
Control of a Vehicle Braking You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work at the places where the tires meet the road. Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That’s perception time. Then you have to bring up your foot and do it. That’s reaction time. Average reaction time is about 3/4 of a second.
Avoid needless heavy braking. Some people drive in spurts -- heavy acceleration followed by heavy braking -- rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking. If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life.
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. Here’s how anti-lock works. Let’s say the road is wet. You’re driving safely. Suddenly an animal jumps out in front of you. You slam on the brakes and continue braking. Here’s what happens with ABS. A computer senses that wheels are slowing down.
Remember: Anti-lock doesn’t change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you won’t have time to apply your brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even though you have anti-lock brakes. Using Anti-Lock Don’t pump the brakes. Just hold the brake pedal down firmly and let anti-lock work for you.
The TRAC OFF light on the button will come on under the following conditions: D The Traction Assist System is turned off, either by pressing the TAS on/off button or turning off the automatic engagement feature of the TAS. D The transmission is in FIRST (1); TAS will not operate in this gear. This is normal. D The vehicle is driven on an extremely rough road. When the vehicle leaves the rough surface, slows down or stops, the light will go off and TAS will be on again. This is normal.
If desired, you can change the TAS automatic engagement feature so that the system will not come on automatically when the engine is started. To do so: Steering 1. Park the vehicle with the ignition off and the transmission in PARK (P). If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. 2. Turn the ignition to RUN; do not start the engine. Power Steering 3.
Suppose you’re steering through a sharp curve. Then you suddenly accelerate. Both control systems -- steering and acceleration -- have to do their work where the tires meet the road. Adding the sudden acceleration can demand too much of those places. You can lose control. Refer to “Traction Assist System” in the Index. What should you do if this ever happens? Ease up on the accelerator pedal, steer the vehicle the way you want it to go, and slow down.
Off-Road Recovery You may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dangerous move, since the passing vehicle occupies the same lane as oncoming traffic for several seconds.
D Check your mirrors, glance over your shoulder and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane. (Remember that your right outside mirror is convex. The vehicle you just passed may seem to be farther away from you than it really is.) D Try not to pass more than one vehicle at a time on two-lane roads.
If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, your vehicle may straighten out. Always be ready for a second skid if it occurs. Off-Road Driving with Your Four-Wheel-Drive Vehicle Of course, traction is reduced when water, snow, ice, gravel or other material is on the road. For safety, you’ll want to slow down and adjust your driving to these conditions.
Before You Go Off-Roading There are some things to do before you go out. For example, be sure to have all necessary maintenance and service work done. Check to make sure all underbody shields (if so equipped) are properly attached. Be sure you read all the information about your four-wheel-drive vehicle in this manual.
Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. Chevrolet recognizes these concerns and urges every off-roader to follow these basic rules for protecting the environment: D Always use established trails, roads and areas that have been specially set aside for public off-road recreational driving; obey all posted regulations.
Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: D you approach things faster and you have less time to scan the terrain for obstacles. D you have less time to react. D you have more vehicle bounce when you drive over obstacles. D you’ll need more distance for braking, especially since you’re on an unpaved surface.
When you drive over obstacles or rough terrain, keep a firm grip on the steering wheel. Ruts, troughs or other surface features can jerk the wheel out of your hands if you’re not prepared. When you drive over bumps, rocks, or other obstacles, your wheels can leave the ground. If this happens, even with one or two wheels, you can’t control the vehicle as well or at all. Because you will be on an unpaved surface, it’s especially important to avoid sudden acceleration, sudden turns or sudden braking.
Approaching a Hill When you approach a hill, you need to decide if it’s one of those hills that’s just too steep to climb, descend or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can easily see all the way to the top. On a large hill, the incline may get steeper as you near the top, but you may not see this because the crest of the hill is hidden by bushes, grass or shrubs.
Driving Uphill Once you decide you can safely drive up the hill, you need to take some special steps. D Use a low gear and get a firm grip on the steering wheel. D Get a smooth start up the hill and try to maintain your speed. Don’t use more power than you need, because you don’t want your wheels to start spinning or sliding. D Try to drive straight up the hill if at all possible. If the path twists and turns, you might want to find another route.
Q: A: What should I do if my vehicle stalls, or is about to stall, and I can’t make it up the hill? If this happens, there are some things you should do, and there are some things you must not do. First, here’s what you should do: D Push the brake pedal to stop the vehicle and keep it from rolling backwards. Also, apply the parking brake. D If your engine is still running, shift the transmission to REVERSE (R), release the parking brake, and slowly back down the hill in REVERSE (R).
Q: A: Suppose, after stalling, I try to back down the hill and decide I just can’t do it. What should I do? Set the parking brake, put your transmission in PARK (P) and turn off the engine. Leave the vehicle and go get some help. Exit on the uphill side and stay clear of the path the vehicle would take if it rolled downhill. Do not shift the transfer case to NEUTRAL when you leave the vehicle. Leave it in some gear.
Driving Downhill When off-roading takes you downhill, you’ll want to consider a number of things: D How steep is the downhill? Will I be able to maintain If you decide you can go down a hill safely, then try to keep your vehicle headed straight down, and use a low gear. This way, engine drag can help your brakes and they won’t have to do all the work. Descend slowly, keeping your vehicle under control at all times.
Q: Are there some things I should not do when driving down a hill? A: Q: A: Yes! These are important because if you ignore them you could lose control and have a serious accident. D Stop your vehicle by applying the regular brakes. D When driving downhill, avoid turns that take you across the incline of the hill. A hill that’s not too steep to drive down may be too steep to drive across. You could roll over if you don’t drive straight down. D Never go downhill with the transmission in NEUTRAL (N).
Driving Across an Incline Sooner or later, an off-road trail will probably go across the incline of a hill. If this happens, you have to decide whether to try to drive across the incline. Here are some things to consider: D A hill that can be driven straight up or down may be too steep to drive across. When you go straight up or down a hill, the length of the wheel base (the distance from the front wheels to the rear wheels) reduces the likelihood the vehicle will tumble end over end.
Q: What if I’m driving across an incline that’s not too steep, but I hit some loose gravel and start to slide downhill. What should I do? A: If you feel your vehicle starting to slide sideways, turn downhill. This should help straighten out the vehicle and prevent the side slipping. However, a much better way to prevent this is to get out and “walk the course” so you know what the surface is like before you drive it.
Driving in Mud, Sand, Snow or Ice When you drive in mud, snow or sand, your wheels won’t get good traction. You can’t accelerate as quickly, turning is more difficult, and you’ll need longer braking distances. It’s best to use a low gear when you’re in mud -- the deeper the mud, the lower the gear. In really deep mud, the idea is to keep your vehicle moving so you don’t get stuck. When you drive on sand, you’ll sense a change in wheel traction. But it will depend upon how loosely packed the sand is.
If the water isn’t too deep, then drive through it slowly. At fast speeds, water splashes on your ignition system and your vehicle can stall. Stalling can also occur if you get your tailpipe under water. And, as long as your tailpipe is under water, you’ll never be able to start your engine. When you go through water, remember that when your brakes get wet, it may take you longer to stop. CAUTION: Driving through rushing water can be dangerous.
Driving at Night Here are some tips on night driving. D Drive defensively. D Don’t drink and drive. D Since you can’t see as well, you may need to slow down and keep more space between you and other vehicles. D Slow down, especially on higher speed roads. Your headlamps can light up only so much road ahead. D In remote areas, watch for animals. D If you’re tired, pull off the road in a safe place and rest. No one can see as well at night as in the daytime.
What you do in the daytime can also affect your night vision. For example, if you spend the day in bright sunshine you are wise to wear sunglasses. Your eyes will have less trouble adjusting to night. But if you’re driving, don’t wear sunglasses at night. They may cut down on glare from headlamps, but they also make a lot of things invisible. You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to readjust to the dark.
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can’t stop, accelerate or turn as well because your tire-to-road traction isn’t as good as on dry roads. And, if your tires don’t have much tread left, you’ll get even less traction. It’s always wise to go slower and be cautious if rain starts to fall while you are driving. The surface may get wet suddenly when your reflexes are tuned for driving on dry pavement. The heavier the rain, the harder it is to see.
CAUTION: Wet brakes can cause accidents. They won’t work as well in a quick stop and may cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car wash, apply your brake pedal lightly until your brakes work normally. Hydroplaning Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles.
Hydroplaning doesn’t happen often. But it can if your tires do not have much tread or if the pressure in one or more is low. It can happen if a lot of water is standing on the road. If you can see reflections from trees, telephone poles or other vehicles, and raindrops “dimple” the water’s surface, there could be hydroplaning. Hydroplaning usually happens at higher speeds. There just isn’t a hard and fast rule about hydroplaning. The best advice is to slow down when it is raining.
City Driving Here are ways to increase your safety in city driving: D Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip. D Try to use the freeways that rim and crisscross most large cities. You’ll save time and energy. See the next part, “Freeway Driving.” D Treat a green light as a warning signal. A traffic light is there because the corner is busy enough to need it.
Freeway Driving At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic. Try to determine where you expect to blend with the flow. Try to merge into the gap at close to the prevailing speed. Switch on your turn signal, check your mirrors and glance over your shoulder as often as necessary. Try to blend smoothly with the traffic flow.
The exit speed is usually posted. Here are some things you can check before a trip: Reduce your speed according to your speedometer, not to your sense of motion. After driving for any distance at higher speeds, you may tend to think you are going slower than you actually are.
Highway Hypnosis Hill and Mountain Roads Is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
If you drive regularly in steep country, or if you’re planning to visit there, here are some tips that can make your trips safer and more enjoyable. See “Off-Road Driving” in the Index for information about driving off-road. CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they wouldn’t work well. You would then have poor braking or even none going down a hill. You could crash.
Winter Driving Here are some tips for winter driving: D Have your vehicle in good shape for winter. D You may want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, a red cloth and reflective warning triangles.
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You’ll have a lot less traction or “grip” and will need to be very careful. What’s the worst time for this? “Wet ice.” Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all.
If you don’t have a traction system, accelerate gently. Try not to break the gentle traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more. If You’re Caught in a Blizzard Your anti-lock brakes improve your vehicle’s stability when you make a hard stop on a slippery road. Even though you have an anti-lock braking system, you’ll want to begin stopping sooner than you would on dry pavement. See “Anti-Lock” in the Index.
Here are some things to do to summon help and keep yourself and your passengers safe: D Turn on your hazard flashers. D Tie a red cloth to your vehicle to alert police that you’ve been stopped by the snow. D Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, floor mats -- anything you can wrap around yourself or tuck under your clothing to keep warm. You can run the engine to keep warm, but be careful.
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Dinghy Towing Four-Wheel-Drive Vehicles When towing your vehicle, turn the ignition off. To prevent your battery from draining while towing, remove the Ignition A and the Ignition B fuses from the engine compartment fuse block. Be sure to reinstall the fuse when you reach your destination. See “Fuses and Circuit Breakers” in the Index. Two-Wheel-Drive Vehicles Two-wheel-drive vehicles, should not be towed with all four wheels on the ground.
4. Shift the transfer case to NEUTRAL (N). See “Four-Wheel Drive” in the Index for the proper procedure to select the NEUTRAL position for your vehicle. Dolly Towing Your vehicle was not designed to be dolly towed. If you need to tow your vehicle see “Dinghy Towing” earlier in this section. 5. Release the parking brake only after the vehicle being towed is firmly attached to the towing vehicle. 6. Turn the ignition off.
Loading Your Vehicle The Certification/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline. Never exceed the GVWR for your vehicle, or the GAWR for either the front or rear axle.
CAUTION: Do not load your vehicle any heavier than the GVWR, or either the maximum front or rear GAWR. If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle. Using heavier suspension components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way.
Adding a Snow Plow or Similar Equipment Your vehicle was neither designed nor intended for a snow plow. NOTICE: Adding a snow plow or similar equipment to your vehicle can damage it, and the repairs wouldn’t be covered by warranty. Do not install a snow plow or similar equipment on your vehicle. Towing a Trailer CAUTION: If you don’t use the correct equipment and drive properly, you can lose control when you pull a trailer.
To identify what the vehicle trailering capacity is for your vehicle, you should read the information in “Weight of the Trailer” that appears later in this section. If yours was built with trailering options, as many are, it’s ready for heavier trailers. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, durability and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly. That’s the reason for this part.
Weight of the Trailer How heavy can a trailer safely be? It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important. And, it can also depend on any special equipment that you have on your vehicle. Look in the following chart to find the maximum trailer weight for your vehicle. 2WD Axle Ratio 3.42 3.73 4.10 4WD 3.42 3.73 4.10 4-52 Max. Trailer Wt. 5,400 lbs. (2 449 kg) 5,900 lbs.
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the upper limit for cold tires. You’ll find these numbers on the Certification label at the rear edge of the driver’s door or see “Tire Loading” in the Index. Then be sure you don’t go over the GVW limit for your vehicle, including the weight of the trailer tongue.
Safety Chains Trailer Brakes You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer. Follow the manufacturer’s recommendation for attaching safety chains and do not attach them to the bumper.
Driving with a Trailer CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You can’t see or smell CO. It can cause unconsciousness or death. See “Engine Exhaust” in the Index. To maximize your safety when towing a trailer: D Have your exhaust system inspected for leaks, and make necessary repairs before starting on your trip. D Keep the rear-most windows closed.
Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You’ll need more passing distance up ahead when you’re towing a trailer. And, because you’re a good deal longer, you’ll need to go much farther beyond the passed vehicle before you can return to your lane. Backing Up Hold the bottom of the steering wheel with one hand.
Turn Signals When Towing a Trailer Driving On Grades The arrows on your instrument panel will flash whenever you signal a turn or lane change. Properly hooked up, the trailer lamps will also flash, telling other drivers you’re about to turn, change lanes or stop. Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don’t shift down, you might have to use your brakes so much that they would get hot and no longer work well.
Parking on Hills CAUTION: You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged. But if you ever have to park your rig on a hill, here’s how to do it: 1. Apply your regular brakes, but don’t shift into PARK (P) yet. When parking uphill, turn your wheels away from the curb. When parking downhill, turn your wheels into the curb. 2.
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: D start your engine, D shift into a gear, and D release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks. Maintenance When Trailer Towing Your vehicle will need service more often when you’re pulling a trailer. See the Maintenance Schedule for more on this.
Trailer Wiring Harness Your vehicle is equipped with the seven-wire trailer towing harness. This harness has a seven-pin universal heavy-duty trailer connector that is attached to a bracket on the hitch platform.
Section 5 Problems on the Road Here you’ll find what to do about some problems that can occur on the road.
Hazard Warning Flashers The button for the hazard warning flashers is located on top of the steering column. The hazard warning flashers work no matter what position your key is in, and even if the key isn’t in. Press the button all the way down to make your front and rear turn signal lamps flash on and off. To turn off the flashers, press the button again until it clicks and then release it. Your hazard warning flashers let you warn others. They also let police know you have a problem.
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. But please use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: D They contain acid that can burn you. D They contain gas that can explode or ignite. D They contain enough electricity to burn you. If you don’t follow these steps exactly, some or all of these things can hurt you.
1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. NOTICE: If the other system isn’t a 12-volt system with a negative ground, both vehicles can be damaged. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles aren’t touching each other. If they are, it could cause a ground connection you don’t want. You wouldn’t be able to start your vehicle, and the bad grounding could damage the electrical systems.
CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You don’t need to add water to the ACDelcoR battery installed in every new GM vehicle. But if a battery has filler caps, be sure the right amount of fluid is there. If it is low, add water to take care of that first. If you don’t, explosive gas could be present.
6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Don’t let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 5-6 8. Now connect the black negative (-) cable to the negative (-) terminal of the good battery. Use a remote negative (-) terminal if the vehicle has one.
9. Connect the other end of the negative (-) cable to the remote negative (-) terminal on the vehicle with the dead battery. 11. Try to start the vehicle that had the dead battery. If it won’t start after a few tries, it probably needs service. NOTICE: Damage to your vehicle may result from electrical shorting if jumper cables are removed incorrectly. To prevent electrical shorting, take care that they don’t touch each other or any other metal. The repairs wouldn’t be covered by your warranty. 10.
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (-) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (-) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery. 4. Disconnect the red positive (+) cable from the other vehicle. Towing Your Vehicle Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part or Remote Negative (-) Terminal B.
Engine Overheating You will find a coolant temperature gage on your vehicle’s instrument panel. See “Gages” in the Index. If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.
If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: D D D D Climb a long hill on a hot day. Stop after high-speed driving. Idle for long periods in traffic. Tow a trailer. See “Driving on Grades” in the Index. If you get the overheat warning with no sign of steam, try this for a minute or so: 1. If your air conditioner is on, turn it off. 2.
Cooling System When the engine is cold, the coolant level should be at least up to the FULL COLD mark. If it isn’t, you may have a leak in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. When you decide it’s safe to lift the hood, here’s what you’ll see: CAUTION: A. Coolant Recovery Tank B. Radiator Pressure Cap C. Engine Fan If the coolant inside the coolant recovery tank is boiling, don’t do anything else until it cools down.
NOTICE: Engine damage from running your engine without coolant isn’t covered by your warranty. How to Add Coolant to the Coolant Recovery Tank If you haven’t found a problem yet, but the coolant level isn’t at the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOLR engine coolant at the coolant recovery tank. See “Engine Coolant” in the Index for more information. NOTICE: When adding coolant, it is important that you use only DEX-COOLR (silicate-free) coolant.
NOTICE: In cold weather, water can freeze and crack the engine, radiator, heater core and other parts. Use the recommended coolant and the proper coolant mixture. CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Don’t spill coolant on a hot engine. When the coolant in the coolant recovery tank is at the FULL COLD mark, start your vehicle.
CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap -- even a little -- they can come out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot. Wait for the cooling system and radiator pressure cap to cool if you ever have to turn the pressure cap.
How to Add Coolant to the Radiator 2. Then keep turning the pressure cap. Remove the pressure cap. 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about one full turn. If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left.
3. Fill the radiator with the proper DEX-COOLR coolant mixture, up to the base of the filler neck. See “Engine Coolant” in the Index for more information about the proper coolant mixture. 5-16 4. Then fill the coolant recovery tank to the FULL COLD mark. 5. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off.
Engine Fan Noise This vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions the clutch is not engaged. This improves fuel economy and reduces fan noise. Under heavy vehicle loading, trailer towing, and/or high outside temperatures, the fan speed increases when the clutch engages. So you may hear an increase in fan noise.
If a Tire Goes Flat Changing a Flat Tire It’s unusual for a tire to “blow out” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers.
Removing the Spare Tire and Tools The following steps will tell you how to use the jack and change a tire. The jacking equipment you will need is stored under the rear seat of the vehicle. See “Rear Seats” in the Index for more information on accessing the jacking equipment under the rear seat.
The tools you’ll be using include the wheel wrench (A), tire blocks (B), extension (socket end) (C), handle (jack end) (D), and jack (E). The following instructions explain how to remove the spare tire mounted underneath your vehicle. NOTICE: Never remove or restow a tire from/to a stowage position under the vehicle while the vehicle is supported by a jack. Always tighten the tire fully against the underside of the vehicle when restowing. 5-20 1.
2. Turn the wheel wrench counterclockwise to lower the spare tire. Keep turning the wheel wrench until the spare tire can be pulled out from under the vehicle. 3. Put the spare tire near the flat tire. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower. See “Secondary Latch System” later in this section. When the tire has been completely lowered, tilt the retainer at the end of the cable and pull it through the wheel opening.
Secondary Latch System The spare tire hoist assembly is equipped with a secondary latch system. It’s designed to stop the spare tire from suddenly falling off your vehicle. For the secondary latch to work, the spare tire must be stored with the valve stem pointing up. See “Storing a Flat or Spare Tire and Tools” in the Index for instructions on storing the spare tire correctly. To release the spare tire from the secondary latch do the following: 1. Check under the vehicle to see if the cable is visible.
8. Continue raising the jack until the spare tire stops moving upward and is held firmly in place. The secondary latch has released and the spare tire is balancing on the jack. 9. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable. CAUTION: 6. Attach the jack handle, extension and the wheel wrench to the jack and place it under the vehicle towards the front of the rear bumper.
10. Disconnect the jack handle from the jack and carefully remove the jack. Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other hand. 11. Tilt the retainer at the end of the cable and pull it through the wheel opening. Pull the tire out from under the vehicle. 12. If the cable is hanging under the vehicle, turn the wheel wrench in the hoist shaft hole in the bumper clockwise to raise the cable back up.
Removing the Flat Tire and Installing the Spare Tire 1. Using the wheel wrench, loosen all the wheel nuts. Don’t remove them yet. 2. Turn the jack adjusting knob clockwise by hand to raise the jack lift head. 3. Place the handle, extension and wheel wrench onto the jack.
Front Rear A. Frame B. Jack C. Handle 5-26 D. Extension E.
4. Place the jack in the appropriate position nearest the flat tire. CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
7. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 8. Place the spare on the wheel mounting surface. CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident.
CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to 100 lb-ft (140 N·m). 11. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. 12.
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. CAUTION: The underbody-mounted spare tire or flat road tire needs to be stored with the valve stem pointing up.
Follow this diagram to store the underbody-mounted spare. A. Wheel Wrench B. Hoist Shaft 4. Raise the tire fully against the underside of the vehicle. Continue turning the wheel wrench until the tire is secure and the cable is tight. The spare tire hoist cannot be overtightened. C. Extension D. Retainer E. Spare or Flat Tire (Valve Stem Pointed Up) 1. Put the tire on the ground at the rear of the vehicle, with the valve stem pointed up and to the rear. 2. Pull the retainer through the wheel. 3.
Return the jack, wheel wrench and wheel blocks to the proper location under the rear seat of the vehicle. Secure the items and return the rear seat to its proper position. If You’re Stuck: In Sand, Mud, Ice or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you don’t want to spin your wheels too fast. The method known as “rocking” can help you get out when you’re stuck, but you must use caution. CAUTION: A. Handle B. Wheel Wrench 5-32 C. Extension D.
NOTICE: Using the Recovery Hooks Spinning your wheels can destroy parts of your vehicle as well as the tires. If you spin the wheels too fast while shifting your transmission back and forth, you can destroy your transmission. For information about using tire chains on your vehicle, see “Tire Chains” in the Index. Rocking Your Vehicle To Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If you have a four-wheel-drive vehicle, shift into 4HI.
CAUTION: The recovery hooks, when used, are under a lot of force. Always pull the vehicle straight out. Never pull on the hooks at a sideways angle. The hooks could break off and you or others could be injured from the chain or cable snapping back. NOTICE: Never use the recovery hooks to tow the vehicle. Your vehicle could be damaged and it would not be covered by warranty.
Section 6 Service and Appearance Care Here you will find information about the care of your vehicle. This section begins with service and fuel information, and then it shows how to check important fluid and lubricant levels. There is also technical information about your vehicle, and a part devoted to its appearance care.
Service Doing Your Own Service Work Your dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ll get genuine GM parts and GM-trained and supported service people. If you want to do some of your own service work, you’ll want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see “Service and Owner Publications” in the Index.
CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. D Be sure you have sufficient knowledge, experience, the proper replacement parts and tools before you attempt any vehicle maintenance task. D Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt.
Gasoline Specifications California Fuel It is recommended that gasoline meet specifications which were developed by the American Automobile Manufacturers Association and endorsed by the Canadian Vehicle Manufacturers’ Association for better vehicle performance and engine protection. Gasolines meeting these specifications could provide improved driveability and emission control system performance compared to other gasolines.
Additives Some gasolines that are not reformulated for low emissions may contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT. General Motors does not recommend the use of such gasolines. Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system may be affected. The malfunction indicator lamp may turn on.
Filling Your Tank CAUTION: Gasoline vapor is highly flammable. It burns violently, and that can cause very bad injuries. Don’t smoke if you’re near gasoline or refueling your vehicle. Keep sparks, flames and smoking materials away from gasoline. While refueling, hang the fuel cap by the tether using the hook located on the inside of the filler door. To remove the fuel cap, turn it slowly to the left (counterclockwise).
CAUTION: If you get gasoline on yourself and then something ignites it, you could be badly burned. Gasoline can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any “hiss” noise to stop. Then unscrew the cap all the way. Be careful not to spill gasoline. Clean gasoline from painted surfaces as soon as possible. See “Cleaning the Outside of Your Vehicle” in the Index.
Filling a Portable Fuel Container CAUTION: Never fill a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: D Dispense gasoline only into approved containers. D Do not fill a container while it is inside a vehicle, in a vehicle’s trunk, pickup bed or on any surface other than the ground.
Hood Release 1. To open the hood, first pull the handle located inside the vehicle on the lower driver’s side of the instrument panel. 2. Then go to the front of the vehicle and release the secondary hood release. 3. Lift the hood, release the hood prop from its retainer and put the hood prop into the slot in the hood. There may be a lamp that comes on when you open the hood.
Engine Compartment Overview When you open the hood you’ll see the following: 6-10
A. Coolant Recovery Tank Engine Oil B. Engine Air Cleaner/Filter If the CHECK OIL LEVEL message appears on the instrument cluster, it means you need to check your engine oil level right away. For more information, see “Check Oil Level Message” in the Index. C. Windshield Washer Fluid Reservoir D. Engine Air Cleaner/Filter Indicator E. Power Steering Fluid Reservoir F. Automatic Transmission Dipstick You should check your engine oil level regularly; this is an added reminder. G.
Turn off the engine and give the oil several minutes to drain back into the oil pan. If you don’t, the oil dipstick might not show the actual level. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level. When to Add Engine Oil If the oil is at or below the L mark, then you’ll need to add at least one quart of oil. But you must use the right kind. This part explains what kind of oil to use.
What Kind of Engine Oil to Use Oils recommended for your vehicle can be identified by looking for the starburst symbol. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Do not use any oil which does not carry this starburst symbol. If you change your own oil, be sure you use oil that has the starburst symbol on the front of the oil container.
As in the chart shown previously, SAE 5W-30 is best for your vehicle. However, you can use SAE 10W-30 if it’s going to be 0 F (-18 C) or above. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils, such as SAE 20W-50. _ _ Engine Oil Additives Don’t add anything to your oil. The recommended oils with the starburst symbol are all you will need for good performance and engine protection.
How to Reset the CHANGE ENG OIL Light What to Do with Used Oil To reset the CHANGE ENG OIL light, do the following: Did you know that used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer? Don’t let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly throw away clothing or rags containing used engine oil.
Engine Air Cleaner/Filter The engine air cleaner/filter is located toward the front of the engine compartment on the passenger’s side of the vehicle. The engine air cleaner/filter assembly has an indicator that lets you know when the air filter is dirty and needs to be serviced. The indicator is located on the engine air cleaner/filter air duct. See “Engine Compartment Overview” in the Index for more information on engine air cleaner/filter indicator location.
After changing the engine air cleaner/filter, press the button on top of the indicator to reset it. See “Owner Checks and Services” in the Index to determine when to check the indicator. To replace the engine air cleaner/filter, do the following: 1. Remove the three screws on the engine air cleaner/filter and lift off the cover. 2. Twist out the old engine air cleaner/filter and replace it with a new one. CAUTION: Operating the engine with the air cleaner/filter off can cause you or others to be burned.
Automatic Transmission Fluid How to Check When to Check and Change Because this operation can be a little difficult, you may choose to have this done at the dealership service department. A good time to check your automatic transmission fluid level is when the engine oil is changed. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick.
To get the right reading, the fluid should be at normal operating temperature, which is 180_F to 200_F (82_C to 93_C). Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50_F (10_C). If it’s colder than 50_F (10_C), drive the vehicle in THIRD (3) until the engine temperature gage moves and then remains steady for 10 minutes.
Then, without shutting off the engine, follow these steps: Locate the handle with the transmission and lock symbols for the automatic transmission dipstick in the engine compartment on the passenger’s side of the vehicle. 3. If the fluid level is in the acceptable range, push the dipstick back in all the way; then flip the handle down to lock the dipstick in place. See “Engine Compartment Overview” in the Index for more information on location. How to Add Fluid 1.
NOTICE: How to Check Lubricant We recommend you use only fluid labeled DEXRONR-III, because fluid with that label is made especially for your automatic transmission. Damage caused by fluid other than DEXRONR-III is not covered by your new vehicle warranty. D After adding fluid, recheck the fluid level as described under “How to Check.” D When the correct fluid level is obtained, push the dipstick back in all the way; then flip the handle down to lock the dipstick in place.
Four-Wheel Drive How to Check Lubricant Lubricant checks in this section also apply to these vehicles. However, there are two additional systems that need lubrication. Transfer Case When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See “Periodic Maintenance Inspections” in the Index. To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, you’ll need to add some lubricant.
Front Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See “Scheduled Maintenance Services” in the Index. How to Check Lubricant If the level is below the bottom of the filler plug hole, you may need to add some lubricant. When the differential is cold, add enough lubricant to raise the level to 1/2 inch (12 mm) below the filler plug hole.
Engine Coolant The cooling system in your vehicle is filled with DEX-COOLR engine coolant. This coolant is designed to remain in your vehicle for 5 years or 150,000 miles (240 000 km), whichever occurs first, if you add only DEX-COOLR extended life coolant. The following explains your cooling system and how to add coolant when it is low. If you have a problem with engine overheating, see “Engine Overheating” in the Index.
What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOLR coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture.
Adding Coolant Checking Coolant The engine coolant recovery tank is in the engine compartment on the passenger’s side of the vehicle. See “Engine Compartment Overview” in the Index for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at FULL COLD, or a little higher. When your engine is warm, the level should be at the base of the filler neck or a little higher.
Add coolant mixture at the recovery tank, but be careful not to spill it. CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Don’t spill coolant on a hot engine. Occasionally check the coolant level in the radiator. For information on how to add coolant to the radiator, see “Cooling System” in the Index.
Power Steering Fluid The power steering fluid reservoir is located in the engine compartment on the passenger’s side of the vehicle. How to Check Power Steering Fluid Turn the key off, let the engine compartment cool down, wipe the cap and the top of the reservoir clean, then unscrew the cap and wipe the dipstick with a clean rag. Replace the cap and completely tighten it. Then remove the cap again and look at the fluid level on the dipstick. The level should be at the C (cold) mark.
Windshield Washer Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. See “Engine Compartment Overview” in the Index for reservoir location. NOTICE: D When using concentrated washer fluid, D Adding Washer Fluid Open the cap with the washer symbol on it.
Brakes Brake Fluid The other reason is that fluid is leaking out of the brake system. If it is, you should have your brake system fixed, since a leak means that sooner or later your brakes won’t work well, or won’t work at all. So, it isn’t a good idea to “top off” your brake fluid. Adding brake fluid won’t correct a leak. If you add fluid when your linings are worn, then you’ll have too much fluid when you get new brake linings.
Checking Brake Fluid What to Add When you do need brake fluid, use only DOT-3 brake fluid. Refer to “Recommended Fluids and Lubricants” in the Index. Use new brake fluid from a sealed container only. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This will help keep dirt from entering the reservoir. CAUTION: You can check the brake fluid without taking off the cap. Just look at the brake fluid reservoir. The fluid level should be above MIN.
NOTICE: D Using the wrong fluid can badly damage D brake system parts. For example, just a few drops of mineral-based oil, such as engine oil, in your brake system can damage brake system parts so badly that they’ll have to be replaced. Don’t let someone put in the wrong kind of fluid. If you spill brake fluid on your vehicle’s painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on your vehicle. If you do, wash it off immediately. See “Appearance Care” in the Index.
Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with your brakes. Brake Adjustment Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque specifications. Replacing Brake System Parts Brake linings should always be replaced as complete axle sets.
Battery Vehicle Storage Your new vehicle comes with a maintenance free ACDelcoR battery. When it’s time for a new battery, get one that has the replacement number shown on the original battery’s label. We recommend an ACDelco battery. See “Engine Compartment Overview” in the Index for battery location. If you’re not going to drive your vehicle for 25 days or more, remove the black, negative (-) cable from the battery. This will help keep your battery from running down.
Bulb Replacement For the type of bulbs, see “Replacement Bulbs” in the Index. For any bulb changing procedure not listed in this section, contact your dealer. Taillamps and Rear Turn Signals 1. Open the liftgate. 2. Remove the two screws from the lamp assembly. 4. Unclip the wiring harness (A) and remove the three socket retaining screws (B). 5. Remove the socket by releasing the retaining tabs. 6. Holding the socket, pull the bulb to release it from the socket. 7.
Windshield Wiper Blade Replacement 1. To remove the old wiper blades, lift the wiper arm until it locks into a vertical position. Windshield wiper blades should be inspected at least twice a year for wear or cracking. See “Wiper Blade Check” in the Index for more information. See “Normal Maintenance Replacement Parts” in the Index for the proper type of replacement blade. NOTICE: Use care when removing or installing a blade assembly.
3. Remove the insert from the blade assembly. The insert has two notches at one end that are locked by the bottom claws of the blade assembly. At the notched end, pull the insert from the blade assembly. A. Claw in Notch 4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully inserted. 5.
Backglass Wiper Blade Replacement See “Windshield Wiper Blade Replacement” in this section for instructions on how to change the backglass wiper blade. The backglass wiper blade will not lock in a vertical position like the windshield wiper blade, so care should be used when pulling it away from the vehicle. Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer.
Inflation -- Tire Pressure The Certification/Tire label, which is on the driver’s door edge, above the door latch, shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). NOTICE: Don’t let anyone tell you that underinflation or overinflation is all right. It’s not.
Tire Inspection and Rotation Tires should be rotated every 6,000 to 8,000 miles (10 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It’s Time for New Tires” and “Wheel Replacement” later in this section for more information. Make sure the spare tire is stored securely. Push, pull, and then try to rotate or turn the tire. If it moves, use the wheel wrench to tighten the cable.
When It’s Time for New Tires CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. See “Changing a Flat Tire” in the Index.
Buying New Tires To find out what kind and size of tires you need, look at the Certification/Tire label. The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each tire’s sidewall. When you get new tires, get ones with that same TPC Spec number. That way your vehicle will continue to have tires that are designed to give proper endurance, handling, speed rating, traction, ride and other things during normal service on your vehicle.
Uniform Tire Quality Grading Treadwear Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
Temperature -- A, B, C Wheel Alignment and Tire Balance The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous.
Tire Chains CAUTION: Don’t use tire chains. There’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions.
Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle: D D D D Alcohol Laundry Soap Bleach Reducing Agents Cleaning the Inside of Your Vehicle Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl, leather, plastic and painted surfaces with a clean, damp cloth. Here are some cleaning tips: D D D D Always read the instructions on the cleaner label. Clean up stains as soon as you can -- before they set.
Special Fabric Cleaning Problems Cleaning Vinyl Stains caused by such things as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, vomit, urine and blood can be removed as follows: Use warm water and a clean cloth. 1. Carefully scrape off excess stain, then sponge the soiled area with cool water. D Things like tar, asphalt and shoe polish will stain 2. If a stain remains, follow the cleaner instructions described earlier. D Rub with a clean, damp cloth to remove dirt.
Cleaning the Top of the Instrument Panel Cleaning Glass Surfaces Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Glass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass.
Cleaning the Outside of the Windshield, Backglass and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid. The windshield is clean if beads do not form when you rinse it with water. Grime from the windshield will stick to the wiper blades and affect their performance.
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. See “Appearance Care and Materials” in the Index. Your vehicle has a “basecoat/clearcoat” paint finish.
Cleaning Aluminum Wheels Cleaning Tires Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. To clean your tires, use a stiff brush with a tire cleaner. The surface of these wheels is similar to the painted surface of your vehicle.
Finish Damage Chemical Paint Spotting Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into a major repair expense. Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ringlet-shaped discolorations, and small irregular dark spots etched into the paint surface.
GM Vehicle Care/Appearance Materials 6-54
Vehicle Identification Number (VIN) Service Parts Identification Label You’ll find this label on the inside of the glove box. It’s very helpful if you ever need to order parts. On this label is: This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Electrical System Headlamps Add-On Electrical Equipment The headlamp wiring is protected by four fuses. An electrical overload will cause a lamp to go on and off. If this happens, have your headlamp wiring checked right away. NOTICE: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty.
Fuses and Circuit Breakers Engine Compartment Fuse Block The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.
6-58
Mini Fuses 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Usage ECAS Passenger’s Side High-Beam Headlamp Passenger’s Side Low-Beam Headlamp Back-Up Trailer Lamps Driver’s Side High-Beam Headlamp Driver’s Side Low-Beam Headlamp WASH ATC Windshield Wipers Powertrain Control Module B Fog Lamps ST/LP Cigarette Lighter COILS RIDE TBD -- Ignition 1 Mini Fuses 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 50 51 52 Usage Crank Air Bag ELEK Brake Cooling Fan Horn Ignition E ETC Instrument Panel Cluster, Driver Information
J-Case Fuses 32 33 34 35 36 Micro Relays 37 38 39 40 41 42 43 44 Solid State Relays 45 46 6-60 Usage Trailer Anti-Lock Brakes (ABS) Ignition A Blower Motor Ignition B Usage Mini Relay Usage 47 Starter Miscellaneous Usage 48 49 Instrument Panel Battery Fuse Puller Rear Underseat Fuse Block Blank Rear Window Washer Fog Lamps Horn Fuel Pump Windshield Wipers/Washer High-Beam Headlamp Air Conditioning Usage Cooling Fan HDM The rear underseat fuse block is located under the rear seat on the driver’s
Fuse Usage 01 Right Door Control Module 02 Left Door Control Module 03 LGM 2 04 TBC 3 05 Rear Fog Lamps 06 LGM/DSM 07 TBC 2 08 Power Seats 09 Blank 10 DDM 11 AMP 12 PDM 13 Rear Climate Controls 14 Left Rear Parking Lamps 15 Auxiliary Power 2 16 VEH CHMSL 6-61
Fuse 6-62 Usage Fuse Usage 17 Right Rear Parking Lamps 36 HVAC B 18 LOCKS 37 Front Parking Lamps 19 Blank 38 Left Turn Signal 20 Sunroof 39 HVAC 1 21 LOCK 40 TBC 4 23 Blank 41 Radio 24 UNLOCK 42 TR PARK 25 Blank 43 Right Turn Signal 26 Blank 44 HVAC 45 Rear Fog Lamps 27 OH Battery/OnStarR System 29 Rainsense Wipers 46 Auxiliary Power 1 30 Parking Lamps 47 Ignition 0 31 TBC 4CC 48 Four-Wheel Drive 32 TBC5 49 Blank 33 Front Wipers 50 TBC IG 34
Replacement Bulbs Lamps Number Tail and Stoplamps . . . . . . . . . . . . . . . . . . . . . 3157 Rear Turn Signal Lamps . . . . . . . . . . . . . . . . . 3157 For any bulb not listed here contact your dealer. Capacities and Specifications Engine Specifications Engine Description . . . . . . . . . . . . “VORTEC” 4200 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . L6 VIN Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S Firing Order . . . . . . . . . . . .
Section 7 Maintenance Schedule This section covers the maintenance required for your vehicle. Your vehicle needs these services to retain its safety, dependability and emission control performance.
Introduction Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance procedures are important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle.
How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs. CAUTION: Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured.
Part A: Scheduled Maintenance Services Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we don’t know exactly how you’ll drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways.
Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. The services shown at 150,000 miles (240 000 km) should be performed at the same interval after 150,000 miles (240 000 km). See “Owner Checks and Services” and “Periodic Maintenance Inspections” following. Footnotes [ The U.S.
Scheduled Maintenance Engine Oil Scheduled Maintenance Change engine oil and filter as indicated by the GM Oil Life System (or every 12 months, whichever occurs first). Reset the system. The system will show you when to change the oil -- usually between 3,000 miles (5 000 km) and 12,000 miles (20 000 km) since your last oil change. Under severe conditions, the indicator may come on before 3,000 miles (5 000 km).
Scheduled Maintenance 7-7
Scheduled Maintenance 7-8
Scheduled Maintenance 7,500 Miles (12 500 km) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. j Rotate tires. See “Tire Inspection and Rotation” in the Index for proper DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: rotation pattern and additional information. (See footnote +.) 15,000 Miles (25 000 km) j Check rear/front axle fluid level and add fluid as needed.
Scheduled Maintenance 30,000 Miles (50 000 km) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. j Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. (See footnote +.) j Replace fuel filter. DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: An Emission Control Service. (See footnote [.
Scheduled Maintenance 50,000 Miles (83 000 km) j Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: – In heavy city traffic where the outside temperature regularly reaches 90_F (32_C) or higher. – In hilly or mountainous terrain. – When doing frequent trailer towing. – Uses such as found in taxi, police or delivery service.
Scheduled Maintenance 60,000 Miles (100 000 km) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. j Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information. (See footnote +.) j Inspect engine accessory drive belt. An Emission Control Service. j Replace fuel filter.
Scheduled Maintenance 82,500 Miles (137 500 km) j Check rear/front axle fluid level and add fluid as needed. Check constant velocity joints and axle seals for leaking. j Rotate tires. See “Tire Inspection and Rotation” in the Index for proper DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: rotation pattern and additional information. (See footnote +.) 90,000 Miles (150 000 km) j Check rear/front axle fluid level and add fluid as needed.
Scheduled Maintenance 100,000 Miles (166 000 km) j Replace spark plugs. An Emission Control Service. j Change automatic transmission fluid and filter if the vehicle is mainly driven DATE ACTUAL MILEAGE SERVICED BY: DATE ACTUAL MILEAGE SERVICED BY: under one or more of these conditions: – In heavy city traffic where the outside temperature regularly reaches 90_F (32_C) or higher. – In hilly or mountainous terrain. – When doing frequent trailer towing.
Part B: Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Part D.
At Least Twice a Year Restraint System Check Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken air bag coverings, and have them repaired or replaced.
Weatherstrip Lubrication Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather more frequent application may be required. See “Recommended Fluids and Lubricants” in the Index. Automatic Transmission Check Check the transmission fluid level; add if needed. See “Automatic Transmission Fluid” in the Index. A fluid loss may indicate a problem. Check the system and repair if needed.
Starter Switch Check CAUTION: When you are doing this check, the vehicle could move suddenly. If it does, you or others could be injured. Follow the steps below. 1. Before you start, be sure you have enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake. See “Parking Brake” in the Index if necessary. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts. 3. Try to start the engine in each gear.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition key to LOCK in each shift lever position. D The key should turn to LOCK only when the shift lever is in PARK (P). D The key should come out only in LOCK. Parking Brake and Automatic Transmission PARK (P) Mechanism Check CAUTION: Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.
Part C: Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your dealer’s service department or other qualified service center do these jobs. Make sure any necessary repairs are completed at once. Proper procedures to perform these services may be found in a service manual. See “Service and Owner Publications” in the Index.
Transfer Case and Front Axle (Four-Wheel Drive) Inspection Every 12 months or at engine oil change intervals, check front axle and transfer case and add lubricant when necessary. A fluid loss could indicate a problem; check and have it repaired, if needed. Check vent hose at transfer case for kinks and proper installation. More frequent lubrication may be required on off-road use. Brake System Inspection Inspect the complete system.
Part D: Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. USAGE FLUID/LUBRICANT Engine Oil Engine oil with the American Petroleum Institute Certified for Gasoline Engines starburst symbol of the proper viscosity. To determine the preferred viscosity for your vehicle’s engine, see “Engine Oil” in the Index.
USAGE FLUID/LUBRICANT USAGE FLUID/LUBRICANT Key Lock Cylinders Multi-Purpose Lubricant, SuperlubeR (GM Part No. 12346241 or equivalent). Chassis Lubrication Chassis Lubricant (GM Part No. 12377985 or equivalent) or lubricant meeting requirements of NLGI # 2, Category LB or GC-LB. Rear Driveline Center Spline and Universal Joints Chassis Lubricant (GM Part No. 12377985 or equivalent) or lubricant meeting requirements of NLGI # 2, Category LB or GC-LB.
USAGE FLUID/LUBRICANT USAGE FLUID/LUBRICANT Hood and Door Hinges Multi-Purpose Lubricant, SuperlubeR (GM Part No. 12346241 or equivalent). Multi-Purpose Lubricant, SuperlubeR (GM Part No. 12346241 or equivalent). Body Door Hinge Pins, Liftgate Hinge and Linkage, Folding Seats and Fuel Door Hinge Outer Tailgate Handle Pivot Points and Hinges Multi-Purpose Lubricant, SuperlubeR (GM Part No. 12346241 or equivalent). Weatherstrip Conditioning Dielectric Silicone Grease (GM Part No.
Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service in the boxes provided after the maintenance interval. Any additional information from “Owner Checks and Services” or “Periodic Maintenance” can be added on the following record pages. Also, you should retain all maintenance receipts. Your owner information portfolio is a convenient place to store them.
Maintenance Record DATE 7-26 ODOMETER READING SERVICED BY MAINTENANCE PERFORMED
Maintenance Record DATE ODOMETER READING SERVICED BY MAINTENANCE PERFORMED 7-27
Maintenance Record DATE 7-28 ODOMETER READING SERVICED BY MAINTENANCE PERFORMED
Maintenance Record DATE ODOMETER READING SERVICED BY MAINTENANCE PERFORMED 7-29
Maintenance Record DATE 7-30 ODOMETER READING SERVICED BY MAINTENANCE PERFORMED
Section 8 Customer Assistance Information Here you will find out how to contact Chevrolet if you need assistance. This section also tells you how to obtain service publications and how to report any safety defects.
Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
STEP TWO -- If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, contact the Chevrolet Customer Assistance Center by calling 1-800-222-1020. In Canada, contact GM of Canada Customer Communication Centre in Oshawa by calling 1-800-263-3777 (English) or 1-800-263-7854 (French). We encourage you to call the toll-free number in order to give your inquiry prompt attention.
You may contact the BBB using the toll-free telephone number or write them at the following address: BBB Auto Line Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800 Arlington, VA 22203-1804 Telephone: 1-800-955-5100 This program is available in all 50 states and the District of Columbia. Eligibility is limited by vehicle age, mileage and other factors. General Motors reserves the right to change eligibility limitations and/or discontinue its participation in this program.
Canada General Motors of Canada Limited Customer Communication Centre, 163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800 All Overseas Locations Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) General Motors de Mexico, S. de R.L. de C.V.
Chevrolet Roadside Assistance Program Roadside Assistance is available 24 hours a day, 365 days a year, by calling 1-800-CHEV-USA (243-8872). This toll-free number will provide you over-the-phone roadside assistance with minor mechanical problems. If your problem cannot be resolved over the phone, our advisors have access to a nationwide network of dealer recommended service providers. Roadside membership is free; however some services may incur costs.
Roadside Courtesy Care provides: D Roadside Basic Care services (as outlined previously) Plus: D FREE Non-Warranty Towing (to the closest dealer from a legal roadway) D FREE Locksmith/Key Service (when keys are lost on the road or locked inside) D FREE Flat Tire Service (spare installed on the road) D FREE Jump Start (at home or on the road) D FREE Fuel Delivery ($5 of fuel delivered on the road) Chevrolet offers Courtesy Transportation for customers needing warranty service.
For prompt assistance when calling, please have the following available to give to the advisor: D D D D D D D Vehicle Identification Number (VIN) License plate number Vehicle color Vehicle location Telephone number where you can be reached Vehicle mileage Description of problem Canadian Roadside Assistance Vehicles purchased in Canada have an extensive Roadside Assistance program accessible from anywhere in Canada or the United States.
If the dealer requests that you simply drop the vehicle off for service, you are urged to do so as early in the work day as possible to allow for same day repair. Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Chevrolet helps minimize your inconvenience by providing several transportation options.
Courtesy Transportation is available only at participating dealers and all program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for specific information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel.
REPORTING SAFETY DEFECTS TO THE CANADIAN GOVERNMENT REPORTING SAFETY DEFECTS TO GENERAL MOTORS If you live in Canada, and you believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited. You may write to: Transport Canada 330 Sparks Street Tower C Ottawa, Ontario K1A 0N5 In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us.
2002 CHEVROLET SERVICE PUBLICATIONS ORDERING INFORMATION The following publications covering the operation and servicing of your vehicle can be purchased by filling out the Service Publication Order Form in this book and mailing it in with your check, money order, or credit card information to Helm, Incorporated (address below.
ORDER TOLL FREE (NOTE: For Credit Card Holders Only) 1-800-551-4123 (Monday-Friday 8:00 AM – 6:00 PM EST) FAX Orders Only 1-313-865-5927 www.helminc.com 2 0 0 2 PUBLICATION FORM NUMBER Orders will be mailed within 10 days of receipt. Please allow adequate time for postal service. If further information is needed, write to the address shown below or call 1-800-551-4123. Material cannot be returned for credit without packing slip with return information within 30 days of delivery.
