2005 Chevrolet Uplander Owner Manual Seats and Restraint Systems ........................... 1-1 Front Seats ............................................... 1-3 Rear Seats ............................................... 1-7 Safety Belts ............................................. 1-22 Child Restraints ....................................... 1-41 Airbag System ......................................... 1-72 Restraint System Check ............................ 1-86 Features and Controls ......................
Canadian Owners A French language copy of this manual can be obtained from your dealer or from: Helm, Incorporated P.O. Box 07130 Detroit, MI 48207 GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, and the CHEVROLET Emblem are registered trademarks; and the name UPLANDER is a trademark of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Safety Warnings and Symbols There are a number of safety cautions in this book. We use a box and the word CAUTION to tell about things that could hurt you if you were to ignore the warning. You will also find a circle with a slash through it in this book. This safety symbol means “Do Not,” “Do Not do this” or “Do Not let this happen.” {CAUTION: These mean there is something that could hurt you or other people. In the caution area, we tell you what the hazard is.
Vehicle Damage Warnings Vehicle Symbols Also, in this manual you will find these notices: The vehicle has components and labels that use symbols instead of text. Symbols are shown along with the text describing the operation or information relating to a specific component, control, message, gage, or indicator. Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle.
These are some examples of symbols that may be found on the vehicle: v
✍ NOTES vi
Section 1 Seats and Restraint Systems Front Seats ......................................................1-3 Manual Seats ................................................1-3 Six-Way Power Seats .....................................1-4 Heated Seats .................................................1-4 Reclining Seatbacks ........................................1-5 Head Restraints .............................................1-7 Rear Seats .......................................................
Section 1 Seats and Restraint Systems Airbag System ...............................................1-72 Where Are the Airbags? ................................1-74 When Should an Airbag Inflate? .....................1-77 What Makes an Airbag Inflate? .......................1-78 How Does an Airbag Restrain? .......................1-78 What Will You See After an Airbag Inflates? ........1-79 Passenger Sensing System ............................1-80 1-2 Servicing Your Airbag-Equipped Vehicle ...........
Front Seats {CAUTION: Manual Seats Use the lever located on the front of the seat to adjust the seat forward or rearward. Pull up the lever to unlock the seat. Slide the seat to where you want it and release the lever. You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Six-Way Power Seats Your vehicle may have this feature. If it does, the six-way power seat control is located on the outboard side of the driver’s seat. Your vehicle may also have a passenger’s six-way power seat. Heated Seats Your vehicle may have this feature. If it does, the heated seat buttons are located on the climate control panel. This feature will heat the lower cushions of the driver’s and front passenger’s seats.
Press this button once to turn on the front passenger’s heated seat to the high setting. Reclining Seatbacks Both indicator lights to the left of the symbol will be lit to indicate that it is on the high setting. Press the button a second time to go to the low setting. One indicator will be lit. Press the button a third time to turn the heated seat off.
{CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job because it will not be against your body. Instead, it will be in front of you. In a crash you could go into it, receiving neck or other injuries. But don’t have a seatback reclined if your vehicle is moving. 1-6 The lap belt can not do its job either.
Head Restraints Rear Seats Rear Seat Operation The rear seats in your vehicle have levers and straps used to adjust, remove, and reinstall the seats. By using the levers and straps in the correct order, you can easily remove the seats from the vehicle. When reinstalling the seats, make sure the seats are in the proper positions. If your vehicle has a second row center console, it can be removed. See Second Row Center Console on page 2-53.
Flip and Fold Feature (Bucket Seats) The rear seats in your vehicle can be folded forward. Use this feature for exiting and entering third row seats. 1. Ensure the adjustable head restraints are fully down. 3. Release the rear set of hooks from the floor pins by pulling the nylon strap located at the base of the seat. Hang on to the strap to guide the seat forward. To return the seat(s) to the normal position, do the following: 1.
Bucket Seats If your vehicle has the bucket seats, the seatbacks can be folded down or reclined. The seats can also be adjusted forward or rearward, or removed. The other lever is located on the rear of the bucket seat. One of the bucket seats may be equipped with a built-in child restraint. See Built-In Child Restraint on page 1-61. Adjusting the Bucket Seats There are two adjustment levers on each seat to adjust the seat forward or rearward. Lift up either lever and slide the seat forward or rearward.
Folding or Reclining the Seatbacks {CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. The seatback on a bucket seat can be either folded forward or reclined. The following explains how to use either the nylon strap or the lever to fold or recline the seatback.
To recline the seatback, pull the nylon strap or lift the recliner lever. Press back on the seatback until you reach the desired position, then let go of the strap or lever. To return the seatback to an upright position, pull on the nylon strap or lift the recliner lever without putting any pressure on the seatback. Push and pull on the seatback to be sure it is locked into place. Removing the Bucket Seats Make sure the seatback is in the upright position. The head restraints should be fully down. 1.
You can also lift the lever on the side of the seat to release the rear latches from the floor pins. Do not let go of the strap or lever until the seat is folded all the way forward. 1-12 4. To unlatch the front latches, with the seat folded forward, squeeze the angled bar toward the straight crossbar. 5. Remove the seat by rocking it slightly forward, then toward the rear of the vehicle and then pulling it out. This should be done in one motion.
Replacing the Bucket Seats {CAUTION: {CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. {CAUTION: A seat that is not locked into place properly can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to lock the seat into place properly when installing it.
2. Make sure the bucket seat is angled so that the front hooks clear the floor pins. If the front hooks are not attached correctly, the rear hooks will not attach to the rear set of floor pins. If the front hooks are not attaching correctly, check that the seat is in the full rear position. 3. Firmly push the rear hooks onto the rear floor pins by pushing down the rear of the seat. 4. Try to raise the seat to check that it is locked down. 5.
Adjusting the Captain’s Chairs (Second Row) The second row captain’s chairs can be adjusted forward or rearward. There are two manual adjustment bars on each seat. One is located under the front of the seat cushion. The other one is located under the rear of the seat cushion. Lift up either bar to slide the seat forward or rearward. Release the lever. Push and pull on the seat to make sure it is locked into place.
Removing the Captain’s Chairs 2. The seat can then be lifted off the front floor pins and removed from the vehicle. 1. Pull the nylon strap behind the seat to release the rear hooks from the floor pins.
Replacing the Captain’s Chairs {CAUTION: {CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
1. Hook the front latches over the front floor pins. 2. Push the rear of the seat down to lock the rear latches onto the rear set of floor pins. 3. Push and pull on the seat to be sure it is properly attached.
Third Row Seat Your vehicle may have a third row seat. It is a full bench seat and may come with the convenience center. See Convenience Center on page 2-56 for more information. The third row seat can be removed and replaced, or with the seatback folded, it will lie flat with the convenience center. Folding the Seatback(s) To fold down either side of the 50/50 split bench seat, pull up on the lever located on the back of the seat you want to fold, and push the seatback down until it is locked into place.
Removing the Third Row Seat 1. Remove the convenience center, if equipped. See Convenience Center on page 2-56 for more information. 2. Make sure all items are off the seat. 3. Put the seatback in its folded position before removing the seat. See “Folding the Seatback(s)” earlier in this section. 5. Lift the seat slightly from the floor to ensure the latches are clear of the floor pins. 6. Pull the seat rearward and out of the vehicle. The release handle can be used to carry the seat.
{CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After installing the seat, always check to be sure that the safety belts are properly routed and attached, and are not twisted. Do not put the third row seat in so it faces rearward because it will not latch that way. The seat has to go in before the convenience center.
Safety Belts {CAUTION: Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It tells you some things you should not do with safety belts. {CAUTION: Do not let anyone ride where he or she can not wear a safety belt properly. If you are in a crash and you are not wearing a safety belt, your injuries can be much worse. You can hit things inside the vehicle or be ejected from it. You can be seriously injured or killed.
In most states and in all Canadian provinces, the law says to wear safety belts. Here’s why: They work. You never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one. Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. A few crashes are mild, and some crashes can be so serious that even buckled up a person wouldn’t survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away.
Put someone on it. 1-24 Get it up to speed. Then stop the vehicle. The rider doesn’t stop.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel...
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after an accident if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But you can unbuckle a safety belt, even if you are upside down. And your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers. Most accidents occur within 25 miles (40 km) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 km/h). Safety belts are for everyone.
4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-41. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 3. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Q: What is wrong with this? {CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. A: The shoulder belt is too loose. It will not give nearly as much protection this way.
Q: What is wrong with this? {CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. A: The belt is buckled in the wrong place.
Q: What is wrong with this? {CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. A: The belt is over an armrest.
Q: What is wrong with this? {CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen. A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
Q: What is wrong with this? {CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it. A: The belt is twisted across the body. To unlatch the belt, just push the button on the buckle. The belt should go back out of the way.
Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle. Shoulder Belt Height Adjustment Before you begin to drive, move the shoulder belt adjuster to the height that is right for you. To move it down, push down on the button and move the height adjuster to the desired position. You can move the adjuster up by pushing up on the shoulder belt guide.
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Lap-Shoulder Belt All rear seating positions have lap-shoulder belts. Here is how to wear one properly. Right Front Passenger Position To learn how to wear the right front passenger’s safety belt properly, see Driver Position on page 1-27.
When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again. If the belt is not long enough, see Safety Belt Extender on page 1-41. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 3. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part.
The safety belt locks if there is a sudden stop or a crash, or if you pull the belt very quickly out of the retractor. {CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. To unlatch the belt, just push the button on the buckle.
1. Remove the guide from its storage pocket on the side of the seatback. 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide.
3. Be sure that the belt is not twisted and it lies flat. The guide must be on top of the belt. 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-36. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides. Slide the guide into the storage pocket.
Safety Belt Pretensioners Your vehicle has safety belt pretensioners. Although you cannot see them, they are located on the retractor part of the safety belts for the driver and right front passenger. They help the safety belts reduce a person’s forward movement in a moderate to severe frontal or near frontal crash. Child Restraints Older Children Pretensioners work only once. If they activate in a crash, you will need to get new ones, and probably other new parts for your safety belt system.
Q: What is the proper way to wear safety belts? A: If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. It should never be worn over the abdomen, which could cause severe or even fatal internal injuries in a crash. Accident statistics show that children are safer if they are restrained in the rear seat.
Q: What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? A: Move the child toward the center of the vehicle, but be sure that the shoulder belt still is on the child’s shoulder, so that in a crash the child’s upper body would have the restraint that belts provide. If the child is sitting in a second row position, see Rear Safety Belt Comfort Guides for Children and Small Adults on page 1-38. {CAUTION: Never do this.
Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Young children should not use the vehicle’s adult safety belts alone, unless there is no other choice. Instead, they need to use a child restraint. 1-44 {CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much — until a crash. During a crash a baby will become so heavy it is not possible to hold it.
{CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide.
For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. The restraint manufacturer’s instructions that come with the restraint state the weight and height limitations for a particular child restraint. In addition, there are many kinds of restraints available for children with special needs.
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous flat surface. Make sure that the infant’s head rests toward the center of the vehicle. A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint.
A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. 1-48 A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a five-point harness. A booster seat can also help a child to see out the window.
Q: How do child restraints work? A: A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner. For many years, add-on child restraints have used the adult belt system in the vehicle. To help reduce the chance of injury, the child also has to be secured within the restraint.
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General Motors recommends that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat. Your vehicle has a rear seat that will accommodate a rear-facing child restraint.
Wherever you install it, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle — even when no child is in it. Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle.
If the position you are using has an adjustable head restraint, route the top strap under it. See Head Restraints on page 1-7. Once you have the top strap anchored, you will be ready to secure the child restraint itself. Tighten the top strap when and as the child restraint manufacturer’s instructions say.
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will find anchors in each seating position in the second row. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts. Instead, it uses vehicle anchors and child restraint attachments to secure the restraints. Some restraints also use another vehicle anchor to secure a top tether strap. Third Row A. Top Strap Anchor B.
To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback. The labels are located at each lower anchor position, near the base of each second row seating position. {CAUTION: A. Lower Anchorage B. Lower Anchorage In order to use the LATCH system in your vehicle, you need a child restraint designed for that system.
Securing a Child Restraint Designed for the LATCH System Securing a Child Restraint in a Rear Seat Position 1. Find the LATCH anchorages for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-53. If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-53.
3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-56 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 6. Push and pull the child restraint in different directions to be sure it is secure.
Securing a Child Restraint in the Right Front Seat Position Your vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-50. In addition, your vehicle has a passenger sensing system. The passenger sensing system is designed to turn off the right front passenger’s airbag or airbags when an infant in a rear-facing infant seat or a small child in a forward-facing child restraint or booster seat is detected.
If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-53. There is no top strap anchor at the right front seating position. Do not secure a child seat in this position if a national or local law requires that the top strap be anchored or if the instructions that come with the child restraint say that the top strap must be anchored. See Top Strap on page 1-51 if your child restraint has one.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 1-60 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
7. Push and pull the child restraint in different directions to be sure it is secure. Built-In Child Restraint 8. If the airbag or airbags are off, the off indicator on the instrument panel will be lit and stay lit when the key is turned to RUN or START. WARNING! DEATH or SERIOUS INJURY can occur: • Follow all instruction on the child restraint and in the vehicle’s owner’s manual. If a child restraint has been installed and the on indicator is lit, turn the vehicle off.
Use only with children who weigh between 22 and 40 pounds (10 and 18 kg) and whose height is between 33.5 and 40 inches (850 and 1 016 mm). Use only with children whose shoulders are below the shoulder belt slots for the harness system and who are capable of sitting upright alone. The child should also be at least one year old. It is important to use a rear-facing infant restraint until the child is at least one year old.
Securing a Child in the Built-In Child Restraint 1. Raise the head restraint until the lower edge of the head restraint is even with the top of the seatback. 2. Rotate the head restraint rearward until it touches the top of the seatback. Make sure there is no gap between the lower edge of the head restraint and the top of the seatback.
3. Lower the child restraint cushion. 1-64 You will be using the child restraint’s harness (A) to secure your child. Do not use the vehicle’s safety belts.
{CAUTION: Using the vehicle’s regular safety belts on a child seated on the built-in child restraint cushion can cause serious injury to the child in a sudden stop or crash. Secure the child using the built-in child restraint’s harness. WARNING: FAILURE TO FOLLOW THE MANUFACTURER’S INSTRUCTIONS ON THE USE OF THIS CHILD RESTRAINT SYSTEM CAN RESULT IN YOUR CHILD STRIKING THE VEHICLE’S INTERIOR DURING A SUDDEN STOP OR CRASH. SNUGLY ADJUST THE BELTS PROVIDED WITH THIS CHILD RESTRAINT AROUND YOUR CHILD. 4.
6. Select only one side of the harness. Place the harness over the child’s shoulder. 7. Push the latch plate (A) into the buckle until it clicks. Be sure the buckle is free of any foreign objects that may prevent you from securing the latch plates. If you can not secure a latch plate, see your dealer for service before using the child restraint. 8. Place the other side of the harness over the child’s shoulder. 9. Push the latch plate into the buckle until it clicks. 1-66 10.
{CAUTION: A built-in child restraint harness that is not properly adjusted can cause injury to the child in a sudden stop or collision. A harness that is loose, twisted, worn improperly or improperly fastened will not be able to restrain the child’s upper body. Make sure the harness is adjusted correctly. Fastening the clip is not a substitute for adjusting the harness so that it is snug. 11. Now fasten the left and right halves of the shoulder harness clip together.
12. Pull the shoulder harness adjustment strap (A) firmly until the harness is snugly adjusted around the child. You should not be able to put more than two fingers between the harness and the child’s chest. Make sure the harness and buckle strap are not twisted. 1-68 13. Adjust the position of the harness on the child’s shoulder by moving the clip along the harness until it is level with the child’s armpits. On each side of the harness, the shoulder part should be centered on the child’s shoulder.
Removing the Child from the Built-In Child Restraint 2. Unlatch the harness by pushing the button on the buckle. 1. Unfasten the shoulder harness clip. 3. Move one side of the harness off the child’s shoulder. 4. Move the other side of the harness off the child’s shoulder. 5. Remove the child from the child restraint cushion.
Storing the Built-In Child Restraint Always properly store the built-in child restraint before using the vehicle’s lap-shoulder belt. 2. Fold the child restraint cushion and leg rest up into the seatback. 3. Press the child restraint cushion firmly into the seatback. 1. Move both latch plates and both sides of the shoulder harness clip to the bottom of the harness straps.
4. Then press the leg rest firmly into the seatback, and secure it by pressing the upper corners against the fastener strips on the seatback. 5. Rotate the head restraint forward and push it all the way down. Just like the other restraint systems in your vehicle, your built-in child restraint needs to be periodically checked and may need to have parts replaced after a crash. See Checking the Restraint Systems on page 1-86 and Replacing Restraint System Parts After a Crash on page 1-87.
Airbag System Your vehicle has airbags — a frontal airbag for the driver and another frontal airbag for the right front passenger. Your vehicle may also have side impact airbags. Side impact airbags are available for the driver and right front passenger. If your vehicle has a side impact airbag for the driver and/or the right front passenger, the words AIR BAG will appear on the airbag covering on the side of the seatback closest to the door.
CAUTION: (Continued) Frontal airbags for the driver and right front passenger are designed to deploy only in moderate to severe frontal and near frontal crashes. They are not designed to inflate in rollover, rear or low-speed frontal crashes, or in many side crashes. And, for some unrestrained occupants, frontal airbags may provide less protection in frontal crashes than more forceful airbags have provided in the past.
The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-34 for more information. {CAUTION: Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. If your vehicle has one, the driver’s side impact airbag is in the side of the driver’s seatback closest to the door.
{CAUTION: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Do not let seat covers block the inflation path of a side impact airbag.
When Should an Airbag Inflate? The driver’s and right front passenger’s frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in time for the airbags to inflate and help restrain the occupants.
The frontal airbags (driver and right front passenger) are not intended to inflate during vehicle rollovers, rear impacts, or in many side impacts because inflation would not likely help the occupants. Your vehicle may or may not have a side impact airbag. See Airbag System on page 1-72. Side impact airbags are designed to inflate in moderate to severe side crashes. A side impact airbag will inflate if the crash severity is above the system’s designed “threshold level.
Airbags should never be regarded as anything more than a supplement to safety belts, and then only in moderate to severe frontal or near-frontal collisions for the driver’s and right front passenger’s frontal airbags, and only in moderate to severe side collisions for vehicles with a driver’s and right front passenger’s side impact airbag. What Will You See After an Airbag Inflates? After the airbag inflates, it quickly deflates, so quickly that some people may not even realize the airbag inflated.
In many crashes severe enough to inflate an airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for your airbag system. If you do not get them, the airbag system will not be there to help protect you in another crash. A new system will include airbag modules and possibly other parts.
The passenger sensing system will turn off the right front passenger’s frontal airbag and side impact airbag (if equipped) under certain conditions. The driver’s airbag or airbags are not part of the passenger sensing system. Passenger Airbag Status Indicator – United States The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt.
Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys.
If a child restraint has been installed and the on indicator is lit, turn the vehicle off. Remove the child restraint from the vehicle and reinstall the child restraint following the child restraint manufacturer’s directions and refer to Securing a Child Restraint in the Right Front Seat Position on page 1-58.
{CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the frontal airbag. See Airbag Readiness Light on page 3-34 for more on this, including important safety information.
{CAUTION: {CAUTION: Stowing of articles under the passenger’s seat or between the passenger’s seat cushion and seatback may interfere with the proper operation of the passenger sensing system. For up to 10 seconds after the ignition key is turned off and the battery is disconnected, an airbag can still inflate during improper service. You can be injured if you are close to an airbag when it inflates. Avoid yellow connectors. They are probably part of the airbag system.
Adding Equipment to Your Airbag-Equipped Vehicle Restraint System Check Checking the Restraint Systems Q: Because I have a disability, I have to get my vehicle modified. How can I find out whether this will affect my airbag system? A: Changing or moving any parts of the front seats, safety belts, the airbag sensing and diagnostic module (located under the driver’s seat), or the instrument panel can affect the operation of the airbag system. If you have questions, call Customer Assistance.
Replacing Restraint System Parts After a Crash {CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
✍ NOTES 1-88
Section 2 Features and Controls Keys ...............................................................2-3 Remote Keyless Entry System .........................2-4 Remote Keyless Entry System Operation ...........2-5 Doors and Locks ............................................2-11 Door Locks ..................................................2-11 Power Door Locks ........................................2-12 Delayed Locking ...........................................2-13 Programmable Automatic Door Locks .....
Section 2 Features and Controls HomeLink® Wireless Control System ...............2-46 HomeLink® Wireless Control System Operation ......................................2-47 Storage Areas ................................................2-51 Glove Box ...................................................2-51 Cupholder(s) ................................................2-51 Overhead Console (With Rail) ........................2-51 Overhead Console (Without Rail) ....................
Keys {CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children. This vehicle has a double sided key for the ignition and the driver’s door lock.
Your vehicle has the PASS-Key® III vehicle theft system. The key has a transponder in the key head that matches a decoder in the vehicle’s steering column. If a replacement key or any additional key is needed, you must purchase this key from your dealer. The key will have PK3 stamped on it. Keep the bar code tag that came with the original keys. Give this tag to your dealer if you need a new key made. Any new PASS-Key® III key must be programmed before it will start your vehicle.
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: • Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. • Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again.
/ (Remote Vehicle Start): If your vehicle has this feature, you can start the engine from outside the vehicle. See “Remote Vehicle Start” at the end of this section for more detailed information. " (Unlock): When you press unlock on the remote keyless entry transmitter, only the driver’s door will unlock. If you press unlock again within five seconds, all the doors and the liftgate will unlock.
Remote Power Sliding Door Operation + (Power Sliding Door): If your vehicle has one power sliding door, the remote keyless entry transmitter will have a button with a van symbol on it. Press and hold this button to open or close the power sliding door. See Power Sliding Door (PSD) on page 2-17. * + (Dual Power Sliding Doors): If your vehicle has dual power sliding doors, your remote keyless entry transmitter will have two buttons that have a van symbol on them.
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about three years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery. Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. 1.
Remote Vehicle Start This feature allows you to start the engine from outside the vehicle. Laws in some local communities may restrict the use of remote starters. For example, some laws may require a person using remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. / (Remote Vehicle Start): If your vehicle has the remote vehicle start feature, the remote keyless entry transmitter will have a button with this symbol on it.
If it is the vehicle’s first remote start, and the engine is still running, repeat Steps 1 and 2 for a 10 minute time extension. Ten minutes will be added to the remaining minutes of the first remote start. The 10 minute time extension is considered a second remote start. After two remote starts have been provided, the vehicle’s ignition switch must be turned to RUN and then back to LOCK using the key before the remote start procedure can be used again.
Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. • Young children who get into unlocked vehicles may be unable to get out.
Power Door Locks From the inside, press the top of the power door lock switch, located on either front door, to unlock all doors and the liftgate. From the inside, use the manual or power door locks. To unlock either front door from the inside, pull back on the manual lever. To lock either front door from the inside, push the manual lever forward. With the content theft-deterrent system, the power door lock switch will not unlock the doors until the system is disarmed.
Delayed Locking Sliding Door Delayed Locking This feature allows the locking of the vehicle to be delayed until all doors have been closed for approximately five seconds. If either sliding door is open when you use the power door locks to lock the vehicle, the sliding door that is open will not lock. Normally the delayed locking feature will be used to lock the sliding door after it has been closed.
Lockout Protection The lockout protection feature makes it more difficult to lock the key in the vehicle. If the driver’s door is open while the key is in the ignition, the door cannot be locked with the power door lock switch. This feature cannot guarantee that you will never be locked out of the vehicle. If the key is not left in the ignition, or, if the manual door lock is used, the key could still be locked inside the vehicle. Always remember to take the key with you.
{CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut be sure to hold it open until everyone is clear of the door, and only then allow it to slowly close. Lock either sliding door from inside the vehicle by moving the manual lever down. Unlock it by moving the lever up. With the power door locks, the sliding door lock has a delay feature.
Sliding Door Security Lock Your vehicle is equipped with sliding door security locks that helps prevent young children or other passengers from opening the sliding door(s) using the inside door handle. To use one of these locks, do the following: 1. Open the sliding door. 2. On the inside of the sliding door(s), on the front edge of the door will be a lock. Push the lever up to engage the lock.
Power Sliding Door (PSD) Power Sliding Door (PSD) Switches If your vehicle has this feature, you can open and close the power sliding door(s) using the switches inside your vehicle. You can also operate the sliding door(s) with your remote keyless entry transmitter. See Remote Keyless Entry System on page 2-4. Your vehicle will have one of the following sets of switches located on the overhead console switchbank. If your vehicle has a single power sliding door (PSD), you have these switches.
If you have a single PSD, this switch is located in front of the passenger side sliding door. If your vehicle has dual PSDs, the switches are located in front of both sliding doors. If your vehicle has dual power sliding doors, you have these switches. The PSD activation and PSD second row passenger override (deactivation) is one switch. Your vehicle also has passenger power sliding door activation switch(es).
Power Sliding Door Operation The power sliding door(s) will only open if the transaxle is in PARK (P). The transaxle does not have to be in PARK (P) to close the door(s). There are several ways to open and close the power sliding door(s). • If your vehicle has a single power sliding door, press the bottom of the overhead console PSD activation switch. • If your vehicle has dual power sliding doors, press the top of the driver’s side and/or passenger’s side overhead console PSD switch.
If the power sliding door has been manually locked, you must unlock the PSD before it can be opened. Notice: If you leave the power sliding door on when you go through an automatic car wash, the door may accidentally open. Be sure the power sliding door is turned off when going through a car wash. If the power sliding door(s) is open or in the process of closing when you shift out of PARK (P), a chime will sound. This is a warning that the sliding door(s) is not completely closed.
{CAUTION: {CAUTION: You or others could be injured if caught in the path of the sliding door. Make sure the door path is clear before closing the door. If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut, turn on the power sliding door feature. Then if the door closes, it will close under the control of the power door system.
Power Sliding Door Second Row Passenger Override (Deactivation) To help avoid accidental operation of the sliding door(s) by using the passenger PSD activation switch, press the overhead console deactivation switch. The door can still be manually opened from the inside or outside with the override (deactivation) switch on.
If the door does not travel to the fully open position, press the overhead console switch to the override (deactivation) position and slide the door fully open and closed. Check for foreign objects in the tracks. Repeat the procedure starting with Step 1. If the door resists travel to the fully open position, see your dealer for service. Liftgate To unlock or lock the liftgate from the outside, use the remote keyless entry transmitter.
Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. To close the liftgate, pull down on the handle, then firmly shut the liftgate. Do not drive with the liftgate open, even slightly.
Power Windows The switches on the driver’s door armrest control the front windows when the ignition is in RUN, ACCESSORY or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-32. The driver’s power window switch has two down positions. The first position lowers the window normally. To raise the window, pull up the front of the switch.
Manual Rear Quarter Windows Power Rear Quarter Windows Your vehicle may have manual rear quarter windows. Your vehicle may have power rear quarter windows. To open, pull the latch forward to release it, then swing the window outward. Press the center of the latch to secure the window in the open position. To close, pull the center of the latch forward and then close the latch. Press the center of the latch to secure the window in the closed position.
Sun Visors Theft-Deterrent Systems To block out glare, you can swing down the visors. You can also remove them from the center mount and swing them to the side. Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Visor Vanity Mirror Your vehicle may have a visor vanity mirror. Pull down the sun visor to access the vanity mirror.
While armed, the doors will not unlock with the power door lock switch. Once armed, the alarm will go off if someone tries to enter the vehicle without using the remote keyless entry transmitter or a key, or turns the ignition to RUN. The horn will sound and the turn signal lamps will flash for up to two minutes.
Arming Confirmation PASS-Key® III If remote unlock confirmation is on, the turn signal lamps will flash briefly to let you know when your alarm system has disarmed. If you would not like the turn signal lamps to flash, see DIC Vehicle Personalization (Uplevel Only) on page 3-68. Your PASS-Key® III system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada.
PASS-Key® III Operation Your vehicle is equipped with the PASS-Key® III (Personalized Automotive Security System) theft-deterrent system. PASS-Key® III is a passive theft deterrent system. This means you do not have to do anything different to arm or disarm the system. It works when you insert or remove the key from the ignition. When the PASS-Key® III system senses that someone is using the wrong key, it shuts down the vehicle’s starter and fuel systems.
To program the new key, do the following: 1. Verify the new key has PK3 stamped on it. 2. Insert the original, already programmed key into the ignition lock cylinder and start the engine. If the engine will not start, see your dealer for service. 3. After the engine has started, turn the key to OFF and remove the key. 4. Insert the key to be programmed and turn it to RUN within 10 seconds of removing the previous key. 5. The security message will turn off once the key has been programmed.
Ignition Positions The key can be turned to one of four positions while in the ignition switch. B (ACCESSORY): This is the position in which you can operate the electrical accessories, such as the the radio. C (RUN): This is the position to which the switch returns after the engine is started and the ignition key is released. This is the position for driving. Even while the engine is not running, RUN can be used to operate your electrical accessories and to display some instrument panel warning lights.
Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle. Shift into PARK (P) only when your vehicle is stopped. 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key.
Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. Your vehicle may also have an internal thermostat in the plug end of the cord.
Automatic Transaxle Operation If you cannot shift out of PARK (P), ease pressure on the shift lever — push the shift lever all the way into PARK (P) as you maintain brake application. Then move the shift lever into the desired gear. See Shifting Out of Park (P) on page 2-40. {CAUTION: Maximum engine speed is limited when the vehicle is in PARK (P) or NEUTRAL (N), to protect driveline components from improper operation. There are several different positions for the shift lever.
REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-32. NEUTRAL (N): In this position, the engine does not connect with the wheels.
Warm-Up Shift Your vehicle has a computer controlled transaxle designed to warm up the engine faster when the outside temperature is 35°F (2°C) or colder. You may notice that the transaxle will shift at a higher vehicle speed until the engine is warmed up. This is a normal condition designed to provide heat to the passenger compartment and defrost the windows more quickly. See Climate Control System on page 3-25 for more information.
All-Wheel Drive If your vehicle has all-wheel drive, your engine’s driving power is sent to all four wheels for extra traction when needed. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts itself as needed for road conditions. Parking Brake The parking brake is located under the instrument panel on the driver’s side of the vehicle.
If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-37. To release the parking brake, hold the regular brake pedal down with your right foot while you push down on the parking brake pedal with your left foot. When you lift your left foot from the parking brake pedal, it will pop up to the released position. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts.
Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Do not leave your vehicle with the engine running.
Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. You might have exhaust coming in if: • Your exhaust system sounds strange or different. • Your vehicle gets rusty underneath.
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-41. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage.
Mirrors Manual Rearview Mirror While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The day/night adjustment can lessen glare from the headlamps behind your vehicle. Pull the tab forward for daytime use; push it back for night use. Push the top control to the left or right to choose either the driver’s or passenger’s outside rearview mirror.
Outside Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services.
Safe and Sound Plan • Automatic Notification of Airbag Deployment • Emergency Services • Roadside Assistance • Stolen Vehicle Tracking • AccidentAssist • Remote Door Unlock/Vehicle Alert • Remote Diagnostics • Online Concierge Directions and Connections Plan • All Safe and Sound Plan Services • Driving Directions • RideAssist • Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability is available if your hand-held cell phone is lost, forgotten,
HomeLink® Wireless Control System If your vehicle is equipped with the HomeLink® transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2.
HomeLink® Wireless Control System Operation Do not use the HomeLink® Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your HomeLink® Transmitter. Read the instructions completely before attempting to program the HomeLink® Transmitter.
Programming HomeLink® Your vehicle’s engine should be turned off while programming the transmitter. Follow these steps to program up to three channels: 1. Press and hold down the two outside buttons, releasing only when the indicator light begins to flash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third transmitter to the remaining two HomeLink® buttons. 2.
6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed HomeLink® button for two seconds, then release.
Using HomeLink® Press and hold the appropriate HomeLink® button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing HomeLink® Buttons To erase programming from the three buttons do the following: Reprogramming a Single HomeLink® Button To program a device to HomeLink® using a HomeLink® button previously trained, follow these steps: 1. Press and hold the desired HomeLink® button. Do not release the button. 2.
Storage Areas Cupholder(s) Your vehicle’s large carrying capacity can store many items. If the vehicle has an extended wheelbase, it can carry even larger items. The floor pins that are used to attach the seats, can be used to secure larger loads. There may be additional storage areas behind the seats. There are cupholders located below the center instrument panel switchbank. The cupholders have a rubber liner that can be removed, so that larger cups can fit into the cupholders.
Storage Bin Your vehicle may have a storage bin located on the overhead rail that you can use for storage. 4. Firmly press down making sure the latch is flat with the ribs (A) on the storage bin. 5. Switch hands and repeat Steps 2 through 4 for the latch on the opposite side of the storage bin. 1. Place the storage bin on to the rails in the desired location. 2. Push firmly upward on the bin while supporting it with one hand. 3. Push in on the latch and then rotate it 90 degrees. 2-52 6.
Overhead Console (Without Rail) Second Row Center Console If your vehicle has an overhead console without the rail system, it has two reading lights, a courtesy light, and a switchbank. See Overhead Console Switchbank on page 3-20 for more information. If your vehicle has the second row center console, use the following procedure to remove or install the console. Floor Console Storage Area If your vehicle has a storage compartment located on the front console below the front cupholders.
Replacing the Center Console Luggage Carrier {CAUTION: {CAUTION: A second row center console that is not locked into place properly can move around in a crash or sudden stop. People in the vehicle could be injured. Be sure to lock the console into place properly when installing it. If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along.
Notice: Loading cargo on the luggage carrier that weighs more than 150 lbs (68 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Don’t exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-33.
Convenience Net (Without Rear Convenience Center) Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over. Install the convenience net at the rear of your vehicle, inside the liftgate. To use the convenience net, do the following: 1. Attach the upper loops to the posts on both sides of the liftgate opening. The label on the net should be in the upper left corner. 2. Attach the lower hooks to the metal rings on the floor. 3.
Removing the Convenience Center 1. Make sure that all items are off the convenience center and that it is empty. 2. Turn the hand knob, located at the rear of the convenience center, counterclockwise until the knob is loose. 3. Lift up on the hand knob, then grip and pull up on the convenience center to remove it from the vehicle. Replacing the Convenience Center 1. Make sure the third row seat is properly installed in the vehicle. See Third Row Seat on page 1-19 for more information.
✍ NOTES 2-58
Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-7 Headlamp High/Low-Beam Changer ..............
Section 3 Instrument Panel Engine Coolant Temperature Gage ..................3-39 Malfunction Indicator Lamp .............................3-40 Oil Pressure Light .........................................3-42 Security Light ...............................................3-43 Cruise Control Light ......................................3-43 Highbeam On Light .......................................3-44 Fuel Gage ...................................................3-44 Low Fuel Warning Light ....................
✍ NOTES 3-3
Instrument Panel Overview 3-4
The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-28. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 3-112. D. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-32. E. Driver Information Center (DIC) Controls (If Equipped). See Driver Information Center (DIC) on page 3-45. F.
Hazard Warning Flashers Horn Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off. Press near or on the horn symbols on your steering wheel pad to sound the horn. The hazard warning flasher button is located near the center of the instrument panel. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive.
Turn Signal/Multifunction Lever • Z Rear Window Wiper. See Windshield Washer on page 3-9. • = Rear Window Washer. See Windshield Washer on page 3-9. For information on the headlamps, see Exterior Lamps on page 3-14. Turn and Lane-Change Signals The lever on the left side of the steering column includes the following: The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change.
As you signal a turn or a lane change, if the arrow flashes faster than normal, a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check for burned-out bulbs and check the fuse. See Bulb Replacement on page 5-46 and Fuses and Circuit Breakers on page 5-96.
Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. 8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. 9(Off): To stop the wipers, move the band to off. N(Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow.
Rear Window Washer/Wiper The controls for the rear window washer/wiper are located on the end of the turn signal/ multifunction lever. Cruise Control Your vehicle may have cruise control. {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. 9 (Off): Move the lever to this position to turn the rear washers/wipers off. Z (Rear Wiper): Move the lever to this position to turn the rear wipers on.
The cruise control lever is located below the windshield wiper control on the right side of the steering wheel. CANCEL R: Pull the lever to cancel the cruise control speed. Cruise control allows a speed of approximately 25 mph (40 km/h) or more to be maintained without keeping your foot on the accelerator. This is helpful on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When the brakes are applied, the cruise control shuts off.
Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Push the button at the end of the cruise control lever to turn the cruise control on. 2. Accelerate to the desired speed. 3. Push down on the cruise control lever and release it. This will set the speed in cruise control.
Increasing Speed While Using Cruise Control Reducing Speed While Using Cruise Control There are two ways to go to a higher speed: There are two ways to reduce the vehicle’s speed while using cruise control: • Use the accelerator pedal to get to the higher speed. Push up on the cruise control lever toward the plus (resume/accelerate) position, then release the lever and take your foot off the accelerator pedal. The vehicle will now cruise at the higher speed.
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle’s speed, its load, and the steepness of the hills. When going up steep hills, the accelerator pedal might have to be used in order to maintain the vehicle’s speed. When going downhill, the brakes might have to be applied, or the transaxle might have to be shifted to a lower gear to keep the vehicle’s speed down. Doing either of these things will take the vehicle out of cruise.
AUTO (Automatic): Turn the control to this position to set your headlamps in automatic mode. AUTO mode, if enabled, will turn the exterior lamps on and off automatically depending on how much light is available outside the vehicle. Due to the momentary switch design, your automatic lights may be disabled even if the control is in the AUTO position.
Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional Daytime Running Lamps are required on all vehicles first sold in Canada. A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered.
Instrument Panel Brightness The knob to adjust the instrument panel brightness is located in the center of the interior lamp controls. Turn the knob clockwise to brighten the lights and counterclockwise to dim them. Interior Lamps Control The interior lamp control is located to the right of the exterior lamp controls on the instrument panel to the left of the steering column. R (Interior Lamp Override): Turn the outer knob to this position to have your interior lamps remain off while any door is open.
Dome Lamp The dome lamp is located in the headliner and has two buttons to manually turn it on or off. The dome lamp will come on each time you open a door, unless you turn on the interior lamps override feature. See Interior Lamps Control on page 3-17. Entry Lighting With entry lighting, the interior of your vehicle is illuminated so that you can see inside before you enter your vehicle.
Exit Lighting Rear Reading Lamps With exit lighting, the interior lamps will come on for about 25 seconds whenever you remove the key from the ignition. If you turn the ignition key to RUN or ACCESSORY, the lamps will fade out. The lamps will also fade out if you lock the doors with the power door lock switch or the remote keyless entry transmitter. There are two reading lamps in the third row headliner. To turn either reading lamp on or off, press the lens of the lamp.
Battery Run-Down Protection Overhead Console Switchbank Your vehicle has a feature to help prevent you from draining the battery, in case you accidentally leave the interior lamps on. If you leave any interior lamps on while the ignition is in lock or off, they will automatically turn off after 10 minutes. The lamps will not come back on again until you do one of the following: • Turn the ignition to RUN or ACCESSORY • Open a closed door, or close and reopen a door.
Ultrasonic Rear Parking Assist (URPA) If your vehicle is equipped with the Ultrasonic Rear Parking Assist (URPA) system, it is designed to help you park, while the vehicle is in REVERSE (R). It operates only at very low speeds, less than 3 mph (5 km/h). URPA can help make parking easier and to help you avoid colliding with objects such as parked vehicles. The URPA system can detect objects up to 5 feet (1.5 m) behind the vehicle, and tell you how close these objects are from your rear bumper.
URPA can be turned off by pressing the rear park aid disable switch located in the overhead console switchbank. While the system is disabled, an indicator light will be lit on the switch. You will not see any lights on the rear display if the switch is in the off position. How the System Works Unless disabled, the URPA will turn on automatically when the shift lever is moved into REVERSE (R).
When the System Does Not Seem to Work Properly Pull the cover down to use the accessory power outlet. When not in use, keep the cover on. The light may flash red when the vehicle is in REVERSE (R) if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice and slush. Other conditions that may affect system performance include things like the vibrations from a jackhammer or the compression of air brakes on a very large truck.
When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. The power outlet is located behind the third row seats on the passenger’s side rear quarter trim panel.
Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode directs half of the air to the instrument panel outlets, then directs the remaining air to the floor outlets. Cooler air is directed to the upper outlets and warmer air to the floor outlets.
9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob to 0 to turn off the fan. The fan must be turned on for the air conditioning compressor to operate. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the air temperature inside your vehicle. # (Air Conditioning): Press this button to turn the air-conditioning system on or off.
Defogging and Defrosting Rear Window Defogger Fog on the inside of windows is a result of high humidity, or moisture, condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. Turn the right knob to select the defog or defrost mode.
Outlet Adjustment Rear Climate Control System k (Open): Your vehicle may have a rear climate control system that allows the driver to adjust the fan speed for the rear seating area. This system works with the main climate control system in your vehicle. Turn the thumbwheel to this position to open the air outlets. l (Closed): Turn the thumbwheel to this position to close the air outlets. Use the louvers located on the air outlets to change the direction of the airflow.
9 (Fan): Slide the lever to 1, 2, or 3 to increase or decrease airflow to the rear seating area. Slide the fan knob to 0 to turn the fan off. AUX: Slide the lever to AUX to allow the rear passengers to adjust the temperature and airflow to the rear seating area. Your vehicle may also have a rear climate control system that allows the rear passengers to adjust the temperature and fan speed for the rear seating area.
t r (Decrease Setting): Press this button to decrease the fan or temperature setting when arrows are active in the display. [ u (Increase Setting): Press this button to increase the fan or temperature setting when arrows are active in display. 9 (Fan): Press this button to increase or decrease fan speed. After pressing this button, arrows and a fan will appear in the display. The arrows indicate that to increase or decrease fan speed, you need to press either the left or right arrow button.
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Gages can indicate when there may be or is a problem with one of your vehicle’s functions.
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. The indicator warning lights and gages are explained on the following pages.
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Your vehicle has a tamper-resistant odometer. You may wonder what happens if your vehicle needs a new odometer installed.
Passenger Safety Belt Reminder Light Several seconds after the key is turned to RUN or START, a chime will be provided for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-80 for more information. The passenger safety belt light will also be provided and stay on for several seconds, then it will flash for several more. You should have the passenger buckle their safety belt.
{CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inflate in a crash, or they could even inflate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should flash for a few seconds when you turn the ignition key to RUN.
If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s airbag or airbags are enabled (may inflate). {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag and seat-mounted side impact airbag (if equipped).
Charging System Light The charging system light will come on briefly when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system. It could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. Driving while this light is on could drain your battery.
If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Anti-Lock Brake System Warning Light on page 3-38 and Towing Your Vehicle on page 4-39. {CAUTION: Your brake system may not be working properly if the brake system warning light is on.
Traction Control System (TCS) Warning Light Your vehicle is equipped with a traction control system warning light. The traction control system warning light may come on for the following reasons: • If you turn the system off by pressing the traction control button. To turn the system back on, press the button again. The warning light should go off. See Traction Control System (TCS) on page 4-9 for more information.
Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is a problem and service is required.
If the Light is Flashing If the Light Is On Steady The following may prevent more serious damage to your vehicle: You may be able to correct the emission system malfunction by considering the following: • • • • Reducing vehicle speed Did you recently put fuel into your vehicle? Avoiding hard accelerations If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that may have developed.
The oil light could also come on in three other situations: Security Light • When the ignition is on but the engine is not running, the light will come on as a test to show you it is working. The light will go out when you turn the ignition on. If it does not come on with the ignition on, you may have a problem with the fuse or bulb. Have it fixed right away. For information regarding this light, see Theft-Deterrent Systems on page 2-27.
Highbeam On Light Your fuel gage tells you about how much fuel you have left when the ignition is on. This light will come on when the high-beam headlamps or the Flash-to-Pass feature is in use. Here are four things some owners ask about. All these things are normal and do not indicate that anything is wrong with the fuel gage. • At the gas station, the gas pump shuts off before the gage reads full.
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages will appear in the DIC display located in the instrument panel cluster, below the tachometer. The DIC buttons are located on the center of the instrument panel, below the center outlets. The DIC comes on when the ignition is on. After a short delay, the DIC will display WELCOME DRIVER (1 or 2) if a personalized key 1 or 2 is used, and then the information that was last displayed before the engine was turned off.
DIC Buttons Information Button Items Q4R (Information): Press this button to scroll through the following items: Odometer Press the information button until the odometer displays. This mode shows the distance the vehicle has been driven in either miles or kilometers. Q4R (Information): Press this button to display the odometer, trip distance, time elapsed, average speed, fuel economy, battery voltage, and oil life.
Time Elapsed Fuel Range Press the information button until TIME ELAPSED :00 displays. This mode is like a stopwatch, in that you can clock the time it takes to get from one point to another. Each of the fields for the hours, minutes, and seconds are two numeric digits. Press the information button until FUEL RANGE displays. This mode shows the approximate number of remaining miles or kilometers the vehicle can be driven without refueling.
Average Fuel Economy Press the information button until AVG ECONOMY displays. This mode shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset. To reset AVG ECONOMY, press and hold the set/reset button. The display will return to zero. Instantaneous Fuel Economy Press the information button until INST ECONOMY displays.
Menu Button Items Personalization (Uplevel Only) q (Menu): Press the menu button until PERSONAL PROGRAM displays. Your vehicle may have personalization capabilities that allow you to program certain features to a preferred setting for up to two drivers. Press this button to scroll through the following items: Units Press the menu button until UNITS displays. This mode allows you to select between English or Metric units of measurement.
Compass Calibration (Uplevel Only) The compass is self-calibrating, which eliminates the need to manually set the compass. However, under certain circumstances, such as during a long distance cross-country trip, it will be necessary to compensate for compass variance and reset the zone through the DIC. Compass variance is the difference between the earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, the compass in the vehicle could give false readings.
5. To start the compass calibration, press and hold the set/reset button until CALIBRATION BEGUN DRIVE UNTIL DONE appears in the DIC display. 6. Drive the vehicle slowly in a circle two times to activate the compass. When the calibration is complete, the DIC will display CALIBRATION FINISHED. DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition.
This message will come on while the ignition is in RUN. Press any of the DIC buttons to acknowledge this warning message and to clear it from the screen. This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on. CHARGING SYSTEM FAILURE This message will display when there is a problem with the generator and battery charging systems.
This message will appear and a chime will sound when the ignition is off. This message cannot be acknowledged. DRIVER’S DOOR AJAR DRIVER’S REAR DOOR AJAR This message will display when the driver’s side rear door is not closed properly. When this message appears, you should make sure that the driver’s side rear door is closed completely. This message will display when the driver’s door is not closed properly. When this message appears, you should make sure that the driver’s door is closed completely.
ENGINE COOLANT HOT Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 5-25 for more information. This message will display when the engine coolant temperature is too hot.
HOOD AJAR If your vehicle has the remote start feature, this message will display when the hood is not closed properly. When this message appears, you should make sure that the hood is closed completely. See Hood Release on page 5-11. This message will display while the ignition is in RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen. This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off.
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. LIFT GATE AJAR If the condition still exists, the message will re-appear when the engine is turned on. This message will display while the ignition is in RUN. A chime will sound when the ignition is shifted out of PARK (P).
This message will display and a chime will sound only while the ignition is in RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen. This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off.
OBSTACLE DETECTED DRVR (Driver) SLIDING DOOR The brake light will also appear on the instrument panel cluster when this message appears on the DIC. See Brake System Warning Light on page 3-37. This message will display to alert the driver that an object is obstructing the driver’s side power sliding door, if equipped, while it is opening or closing. Remove any object that is obstructing the power sliding door. See Power Sliding Door (PSD) on page 2-17 for more information.
PASSENGER’S DOOR AJAR This message will display when the front passenger’s door is not closed properly. When this message appears, you should make sure that the front passenger’s door is closed completely. This message will display while the ignition is in RUN. A chime will sound when the ignition is shifted out of PARK (P). Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
PASSENGER SLIDING DOOR IN MOTION This message will display while the passenger’s side power sliding door, if equipped, is opening or closing. See Power Sliding Door (PSD) on page 2-17 for more information. REDUCED ENGINE POWER This message will display when the vehicle’s engine power is reduced. This happens when driving conditions, such as climbing a steep hill, make the transaxle overwork in a gear that may cause damage to the vehicle’s engine or transaxle.
REMOTE START DISABLED REMOTE START ON This warning message will come on if a remote start attempt is unsuccessful. This may be caused if any of the following conditions are true when a remote start attempt is made: If your vehicle has the remote start feature, this message will display when a remote start is initiated. See “Remote Vehicle Start” under Remote Keyless Entry System Operation on page 2-5 for more information. • The remote start system is disabled through the DIC.
RIGHT REAR TURN LAMP OUT This message will display when the right rear turn signal bulb needs to be replaced. See Taillamps, Turn Signal, Stoplamps and Back-up Lamps on page 5-48. This message will display while the ignition is in RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen. This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off.
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on. SERVICE PARK LAMPS This message will display when there is a problem with the park lamps.
SERVICE TRACTION SYSTEM If your vehicle has the traction control system, this message will display when the system is not functioning properly. A warning light will also appear on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-39. See Traction Control System (TCS) on page 4-9 for more information. Have the traction control system serviced by your GM dealer as soon as possible. This message will display only while the ignition is in RUN.
STABILITY CONTROL OFF If your vehicle has StabiliTrak®, this message will display any time the system turns off. When this message has been displayed, StabiliTrak® is no longer available to assist you with directional control of the vehicle. Adjust your driving accordingly. See StabiliTrak® System on page 4-10. This message will display only while the ignition is in RUN. Any of the following conditions may cause the StabiliTrak® system to turn off: • The battery is low.
This message will only display while the ignition is in RUN and will disappear after two seconds. Any of the following conditions may cause the traction control system to turn off: • The traction control system is turned off by pressing the traction control button located on the center of the instrument panel. See Traction Control System (TCS) on page 4-9. • The battery is low. • There is a traction control system failure. See your GM dealer for service.
DIC Vehicle Personalization (Uplevel Only) All of the customization and personalization options may not be available on your vehicle. Only the options available will be displayed on your DIC. Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers.
3. Press the set/reset button to begin. 4. The DIC will then display an instruction screen. Press the menu button to display the modes that are available to program. Press the set/reset button to change the setting of each mode. Customization Menu Items The following are customization features that allow you to program settings to the vehicle: FACTORY DEFAULTS This feature allows you to set all of the customization and personalization features back to their factory default settings.
EXT (Exterior) LIGHT DELAY INT (Interior) LIGHTS KEYS REMOVED This feature allows you to set the amount of time the exterior lamps remain on after the key is removed from the ignition or the vehicle is unlocked using the remote keyless entry transmitter. This feature enables the interior lamps in the vehicle to turn on for about 25 seconds after the key is removed from the ignition. Press the menu button until EXT LIGHT DELAY appears on the DIC display.
When the delayed locking feature is enabled, it may be activated when the key is out of the ignition by doing one of the following: Press the menu button until DELAYED LOCKING appears on the DIC display. Press the set/reset button to scroll through the following choices: • Pressing the driver’s door power lock switch one OFF: There will be no delayed locking of the vehicle’s doors. time while the driver’s door is open.
Press the menu button until CONTENT THEFT appears on the DIC display. Press the set/reset button to scroll through the following choices: Press the menu button until FOB LOCK FEEDBACK appears on the DIC display. Press the set/reset button to scroll through the following choices: OFF: The content theft-deterrent system will be turned off. OFF: There will be no feedback when locking the vehicle. ON (default): The content theft-deterrent system will be turned on.
Press the menu button until REMOTE START appears on the DIC display. Press the set/reset button to scroll through the following choices: OFF: The remote start feature will be disabled. ON (default): The remote start feature will be enabled. Choose one of the available settings and press the menu button while it is displayed on the DIC to select it and move on to the next feature.
REPLACE KEY This screen displays only if YES was selected for the PERSONALIZE KEY feature, keys 1 and 2 have already been personalized, and the current key being used is not key 1 or 2. This feature allows you to program a key to be recognized as key 1 or 2 in the event that the previously programmed key needs to be replaced. 1: The key will be programmed to be recognized as key 1. 2: The key will be programmed to be recognized as key 2. CANCEL (default): The key will not be programmed.
DRIVER: Only the driver’s door will unlock when the vehicle is shifted into PARK (P) or the key is taken out of the ignition. FOB UNLOCK ON 1ST PRESS ALL (default): All of the doors will unlock when the vehicle is shifted into PARK (P) or the key is taken out of the ignition. This feature allows the selection of which doors will unlock on the first press of the unlock button on the remote keyless entry transmitter. See Remote Keyless Entry System Operation on page 2-5 for more information.
Exiting the Personal Program Menu The personal program menu will be exited when any of the following occurs: • The vehicle is shifted out of PARK (P). • The vehicle is no longer in RUN. • The end of the personal program menu is reached. Figure out which audio system is in your vehicle, find out what your audio system can do, and how to operate all of its controls. Your vehicle has a feature called Retained Accessory Power (RAP).
Radio with CD Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information.
XM™ Satellite Radio Service If your vehicle has XM™, XM™ is a satellite radio service that is based in the 48 contiguous United States. XM™ offers 100 coast-to-coast channels including music, news, sports, talk, and children’s programming. XM™ provides digital quality audio and text information that includes song title and artist name. A service fee is required in order to receive the XM™ service. For more information, contact XM™ at www.xmradio.com or call 1-800-852-XMXM (9696).
To use AudioPilot®, set the radio volume to your desired level. Turn AudioPilot® on by pressing the automatic volume button until AVOL ON appears on the display. As you increase vehicle speed, the background noise in your vehicle will increase. AudioPilot® will adjust your audio system’s output for the background noise it hears. To turn AudioPilot® off, press the automatic volume button until AVOL OFF appears on the display. For additional information on AudioPilot®, please visit www.bose.com.
5. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the station that was set will return and the equalization that was selected will be stored for that pushbutton. 6. Repeat the steps for each pushbutton. Setting the Tone (Bass/Treble) e (Bass/Treble/Midrange): Press this knob to select BASS, MIDRANGE, or TREBLE. Turn the knob to increase or to decrease. If a station is weak or noisy, decrease the treble.
Finding a Category Station (RDS and XM™) To select and find a desired category perform the following: 1. Press the CAT button. The last selected category will appear on the display. 2. Turn the tune knob to select the category. 3. Once the desired category is displayed, press either SEEK arrow to take you to a category’s station. SEEKING CATEGORY will appear on the display. 4.
RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is low or a CD is playing. If a CD is playing, play will stop during the announcement. Alert announcements cannot be turned off. ALERT! will not be affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations.
Radio Messages CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If CAL ERR appears on the display, it means that the radio has not been configured properly for your vehicle and must be returned to your GM dealer for service. LOCKED: This message is displayed when the THEFTLOCK® system has locked up. Take the vehicle to your GM dealer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer.
XM™ Radio Messages (cont’d) Radio Display Message Condition Action Required CH Off Air Channel not in service This channel is not currently in service. Tune to another channel. CH Unavail Channel no longer available This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button. No Info Artist Name/Feature not available No artist information is available at this time on this channel.
XM™ Radio Messages (cont’d) Radio Display Message Condition Action Required Radio ID Radio ID label (channel 0) If tuned to channel 0, this message will alternate with the XM™ Radio eight digit radio ID label. This label is needed to activate the service. Unknown Radio ID not known (should only be if hardware failure) If this message is received when tuned to channel 0, there may be a receiver fault. Consult with your GM dealer.
Do not add paper labels to CDs, they could get caught in the CD player. If an error appears on the display, see “CD Messages” later in this section. O / e (Tune): Turn this knob to go to the next or previous track. { (Reverse): Press and hold this button to reverse the current track. | (Fast Forward): Press and hold this button to fast forward through the current track. RDM (Random): Press this button to hear the tracks in random, rather than sequential, order. RANDOM DISC will appear on the display.
Playing a CD(s) (Six-Disc CD Player) If the ignition or radio is turned off, with a CD in the player, it will stay in the player. When the ignition or radio is turned on, the CD will start playing where it stopped, if it was the last selected audio source. When a CD is inserted, the CD symbol will appear on the CD. As each new track starts to play, the track number will appear on the display. The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring.
Playing a Specific Loaded CD For every CD loaded, a number will appear on the display. To play a specific CD press the numbered pushbutton that corresponds to the CD. Do not repeatedly press the eject button to eject a CD after you have tried to push it in manually. The player’s 25-second eject timer will reset at each press of eject, causing the player to not eject the CD until the 25-second time period has elapsed. If an error appears on the display, see “CD Messages” later in this section.
RPT (Repeat): Press this button to hear a track or an entire CD over again. To use repeat, do one of the following: • To repeat a track, press and release this button until REPEAT appears on the display. • To repeat an entire CD, press and release this button until REPEAT ONE DISC appears on the display.
Using an MP3 CD Root Directory MP3 Format The root directory will be treated as a folder. If the root directory has compressed audio files, the directory will be displayed as F1 ROOT. All files contained directly under the root directory will be accessed prior to any root directory folders. However, playlists (Px) will always be accessed before root folders or files. This MP3 player will accept MP3 files that were recorded on an up to 700 MB CD-R CD.
Order of Play File System and Naming Tracks will be played in the following order: The song name that will be displayed will be the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio will display the file name without the extension (such as .mp3) as the track name. • Play will begin from the first track in the first playlist and will continue sequentially through all tracks in each playlist.
Playing an MP3 Insert a CD partway into the slot, label side up. The player will pull it in, and READING will appear on the display. The CD should begin playing and the CD symbol will appear on the display. If the ignition or radio is turned off with a CD in the player it will stay in the player. When the ignition or radio is turned on, the CD will start to play where it stopped, if it was the last selected audio source. As each new track starts to play, the track number will appear on the display.
RPT (Repeat): Press this button to hear a track, CD, or a folder over again. To use repeat, do one of the following: • To repeat a track, press and release this button until REPEAT TRACK appears on the display. • To repeat a CD, press and release this button until REPEAT DISC appears on the display. • To repeat a folder, press and release this button until REPEAT FOLDER appears on the display. To turn off repeated play, press and release the RPT button until REPEAT OFF appears on the display.
4. Press and hold the song list button to save the track into memory. When song list is pressed, one beep will be heard immediately. ADDED SONG will appear on the display. 5. Repeat Steps 3 and 4 for saving other selections. SONGLIST FULL will appear on the display if you try to save more than 20 selections. To play the song list, press the song list button. The recorded tracks will begin to play in the order they were saved. Seek through the song list by using the SEEK arrows.
CD Messages Rear Seat Entertainment System CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons: Your vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system includes a DVD player, a video display screen, auxiliary inputs, two sets of wireless headphones, and a remote control. • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road.
Before You Drive The RSE is designed for rear seat passengers only. The driver cannot safely view the video screen while driving and should not try to do so. The RSE system will play DVD, CD, and MP3 discs. You can also connect an auxiliary device to the RSE system to play games, watch videos, look at pictures, etc. Normal operation may be limited under extremely low or high temperatures, in order to protect the system from damage. Operate the RSE system under normal or comfortable cabin temperature ranges.
If there is a decreased audio signal during CD, MP3, or DVD play, there may be a low hissing noise through the speakers and/or headphones. If the hissing sound in the wireless headphones seems excessive, make sure that the headphone batteries are fully charged. Some amount of hissing is normal. Battery Replacement To change the batteries, do the following: 1. Loosen the screw on the battery compartment door located on the left side of the headphone earpiece. 2.
Stereo RCA Jacks The yellow RCA jack is used for video inputs, the red RCA jack for right audio inputs, and the white RCA jack for left audio inputs. The system requires standard RCA cables, not included, to connect the auxiliary device to the RCA jacks. Refer to the manufacturer’s instructions for proper usage.
Vehicle Speakers Only one audio source can be heard through the vehicle’s speakers at a time. The RSE system or an auxiliary device can be heard through all of the vehicle’s speakers when the following occurs: • A DVD or auxiliary device is playing • The front audio system is on and the CD AUX button is pressed to enable the RSE system DVD will appear on the radio display when the RSE system is on. To turn the vehicles speakers on and off, press the CD AUX button on the radio.
DVD Player Buttons AUX (Auxiliary): Press this button to switch the system between the DVD player and an auxiliary device. s (Play/Pause): Press this button to start play of a disc. Press this button while a disc is playing to pause it. Press it again to continue play of a disc. tr / [ u (Reverse/Fast Forward): These controls can be used to move forward or backward through a disc. These buttons can also be used to modify RSA, rear temperature, rear fan speed, and wired headphone volume adjustment.
If a disc is already in the player, make sure that the DVD player is on, then press the play/pause button on the player faceplate or on the remote control. You can also, press the CD AUX button on the radio faceplate, until RSE appears on the display, to start playing a disc. Some DVDs will not allow fast forwarding or skipping of the copyright information or previews. Some DVDs will begin playing after the previews have finished.
Remote Control Buttons n, q, p, o (Directional Arrows): Press these buttons to move through DVD menus. The up and down arrows will move through MP3 folders. r (Enter): Press this button to select the choice that is highlighted in any menu. z (Display Control Button): Press this button to open the RSE On-Screen Display (OSD) menus to adjust the color, tint, brightness, contrast, and display modes. y (Main Menu): O (Power): Press this button to turn the DVD player on and off.
s (Play/Pause): Press this button to start play of a disc. Press this button while a disc is playing to pause it. Press it again to continue playing the disc. t (Prior Chapter/Track): Press this button to go to the beginning of the current chapter or track. Press this button again to return to the previous chapter or track. This button may not work when the DVD is playing the copyright information or previews. { (Subtitles): Press this button to display the current subtitles.
RSE On-Screen Display (OSD) Menu To use the RSE OSD menu when using a DVD or an auxiliary device, do the following: To access this menu, press the display button on the remote control. Once the menu is on the screen, use the directional arrows and the enter button to navigate the screen. This menu will let you select default preferences for video format, language preference, brightness, color, contrast, and tint. Not all DVDs support all the feature defaults in the setup menus.
Tips and Troubleshooting Chart Problem Recommended Action No power. The ignition may not be in ACCESSORY, RUN, or RAP. Disc will not play. The system might be off. The parental control button might have been pressed. The power indicator lights will flash. The system might be in auxiliary source mode. Press the AUX button to switch between the DVD player and the auxiliary source. The disc is upside down or is not compatible. No sound — Wireless Headphones Turn the headphones on.
Problem I ejected the disc and tried to take it out, but it was pulled back into the slot. Recommended Action Press the eject button once. The language in the audio Press the main menu or on the screen is wrong. button on the remote control and change the audio or language selection on the DVD menu. To change the language preference, press the display button to access the RSE OSD menu. See “RSE OSD” earlier in this section. The remote control does not work.
Problem Recommended Action The fast forward, reverse, previous, and next functions do not work. Some commands that do one thing for DVDs will not always work or perform the same function for audio, CDs, or games. These functions may also be disabled when the DVD is playing the copyright information or the previews. When RSA is on, these buttons control RSA functions. My disc is stuck in the player. The eject button does not work. Press the eject button on the DVD player.
DVD Messages Problem Recommended Action The wireless headphones have audio distortion. Verify that the headphones are facing to the front of the vehicle, left and right sides are indicated on the headphones to ensure that the signal is received properly. Verify that there is no obstruction between the headphone(s) and the transmitter. Verify that the batteries have a full charge. The following errors may be displayed on the video screen.
DVD Distortion Rear Seat Audio (RSA) There may be an experience with video distortion when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. If your vehicle has rear seat audio (RSA), this feature allows rear seat passengers to listen to and control any of the following audio sources: AM/FM tuner, front CD player, and XM™ Satellite Radio Service (if equipped).
BAND: Press this button to switch between FM1, FM2, AM, or XM1 or XM2 (if equipped). The selected radio station will appear on the display. If the front passengers are listening to the radio, the RSA will not switch between the bands and cannot change the station. tr / [ u (Tune): When listening to the radio, press the right or the left arrow to go to the next or the previous station and stay there. This function is inactive if the front seat passengers are listening to the radio.
When a CD is playing in the single CD player, press this button to select the next track. This function is inactive if the front seat passengers are listening to a CD. When a CD is playing in the six-disc CD changer, press this button to select the next CD, if multiple CDs are loaded. This function is inactive if the front seat passengers are listening to a CD. SRCE (Source): Press this button to switch between playing the AM/FM tuner, front CD player, and XM™ Satellite Radio Service (if equipped).
Theft-Deterrent Feature They include the following: THEFTLOCK® is designed to discourage theft of your vehicle’s radio. The feature works automatically by learning a portion of the Vehicle Identification Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOCKED will appear on the display. wt u x (Seek): With THEFTLOCK® activated, the radio will not operate if stolen.
BAND: Press this button to switch between FM1, FM2, AM, or XM1 or XM2 (if equipped). 1 - 6: Press this button to scan the stations that are programmed on the radio preset pushbuttons. The radio will go to the next preset station stored on the pushbuttons, play for a few seconds, then go on to the next preset station. Press this button again to stop scanning. The radio will only scan preset stations with a strong signal that are in the selected band. $ (Mute): Press this button to silence the system.
Care of Your CDs and DVDs Fixed Mast Antenna Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge. The fixed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, straighten it out by hand. If the mast is badly bent, replace it.
Section 4 Driving Your Vehicle Your Driving, the Road, and Your Vehicle ..........4-2 Defensive Driving ...........................................4-2 Drunken Driving .............................................4-2 Control of a Vehicle ........................................4-6 Braking .........................................................4-6 Anti-Lock Brake System (ABS) .........................4-7 Braking in Emergencies ...................................4-8 Traction Control System (TCS) ..........
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Defensive driving requires that a driver concentrate on the driving task. Anything that distracts from the driving task — such as concentrating on a cellular telephone call, reading, or reaching for something on the floor — makes proper defensive driving more difficult and can even cause a collision, with resulting injury.
Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 16,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with more than 300,000 people injured. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive.
According to the American Medical Association, a 180 lb (82 kg) person who drinks three 12 ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4 ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of liquors like whiskey, gin, or vodka. It is the amount of alcohol that counts.
But the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent. Statistics show that the chance of being in a collision increases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of 0.06 percent has doubled his or her chance of having a collision.
Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering, and the accelerator. All three systems have to do their work at the places where the tires meet the road. Sometimes, as when you are driving on snow or ice, it is easy to ask more of those control systems than the tires and road can provide. That means you can lose control of your vehicle. 66 feet (20 m).
Anti-Lock Brake System (ABS) Your vehicle has anti-lock brakes. ABS is an advanced electronic braking system that will help prevent a braking skid. When you start your engine and begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this test is going on, and you may even notice that your brake pedal moves or pulses a little. This is normal. If there is a problem with the anti-lock brake system, this warning light will stay on.
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Traction Control System (TCS) Your vehicle may have a traction control system that limits wheel spin. This is especially useful in slippery road conditions. On a front-wheel-drive vehicle, the system operates if it senses that one or both of the front wheels are spinning or beginning to lose traction. On an all-wheel-drive vehicle, the system will operate if it senses that any of the wheels are spinning or beginning to lose traction.
The traction control system automatically comes on whenever you start your vehicle. To limit wheel spin, especially in slippery road conditions, you should always leave the system on. But you can turn the traction control system off if you ever need to. You should turn the system off if your vehicle ever gets stuck in sand, mud or snow and rocking the vehicle is required. See Rocking Your Vehicle to Get It Out on page 4-33 and If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-32.
The STABILITY CONTROL ACTIVE message will appear on the DIC only when the system is both on and activated. It means that an advanced computer-controlled system has come on to help your vehicle continue to go in the direction in which you are steering. StabiliTrak® activates when the computer senses that your vehicle is just starting to spin, as it might if you hit a patch of ice or other slippery spot on the road. When the system activates, you may hear a noise or feel a vibration in the brake pedal.
If the brake traction-control system activates constantly or if the brakes have heated up due to high-speed braking, brake traction-control will be disabled and the TRACTION CONTROL ACTIVE message will be displayed. In the limited mode, the traction control system will only use engine traction-control and is limited in its ability to provide optimal performance since the system will not utilize brake traction-control to control slip on the drive wheels.
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips Driving on Curves It is important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here is why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. You can avoid these problems by braking — if you can stop in time. But sometimes you cannot; there is not room. That is the time for evasive action — steering around the problem.
Off-Road Recovery Passing You may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again.
• Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops. Keep back a reasonable distance. • When it looks like a chance to pass is coming up, start to accelerate but stay in the right lane and do not get too close.
Loss of Control A cornering skid is best handled by easing your foot off the accelerator pedal. Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. If you have the Traction Control System (TCS), remember: It helps avoid only the acceleration skid. See Traction Control System (TCS) on page 4-9.
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration, or braking, including engine braking by shifting to a lower gear. Any sudden changes could cause the tires to slide. You may not realize the surface is slippery until your vehicle is skidding. Learn to recognize warning clues — such as enough water, ice, or packed snow on the road to make a mirrored surface — and slow down when you have any doubt.
Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Adjust your inside rearview mirror to reduce the glare from headlamps behind you. • Since you cannot see as well, you may need to slow down and keep more space between you and other vehicles. • Slow down, especially on higher speed roads. Your headlamps can light up only so much road ahead. • In remote areas, watch for animals. • If you are tired, pull off the road in a safe place and rest.
Driving in Rain and on Wet Roads The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking. It is wise to keep your wiping equipment in good shape and keep your windshield washer tank filled with washer fluid.
{CAUTION: Wet brakes can cause accidents. They will not work as well in a quick stop and may cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car wash, apply your brake pedal lightly until your brakes work normally. Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough.
Driving Through Flowing Water Some Other Rainy Weather Tips • Turn on your low-beam headlamps — not just your {CAUTION: Flowing or rushing water creates strong forces. If you try to drive through flowing water, as you might at a low water crossing, your vehicle can be carried away. As little as six inches of flowing water can carry away a smaller vehicle. If this happens, you and other vehicle occupants could drown.
City Driving Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip. • Try to use the freeways that rim and crisscross most large cities. You will save time and energy. See Freeway Driving on page 4-24. • Treat a green light as a warning signal. A traffic light is there because the corner is busy enough to need it.
Freeway Driving The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-fast or too-slow driving breaks a smooth traffic flow. Treat the left lane on a freeway as a passing lane. At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic.
Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night. When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. Is your vehicle ready for a long trip? If you keep it serviced and maintained, it is ready to go. If it needs service, have it done before starting out.
Highway Hypnosis Hill and Mountain Roads Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all fluid levels and also the brakes, tires, cooling system, and transaxle. These parts can work hard on mountain roads. • Know how to go down hills. The most important thing to know is this: let your engine do some of the slowing down. Shift to a lower gear when you go down a steep or long hill.
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Also see Tires on page 5-51. Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, a red cloth, and a couple of reflective warning triangles.
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You will have a lot less traction, or grip, and will need to be very careful. What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all.
Unless you have the anti-lock braking system (ABS), you will want to brake very gently, too. If you do have ABS, see Anti-Lock Brake System (ABS) on page 4-7. ABS improves your vehicle’s stability when you make a hard stop on a slippery road. Whether you have ABS or not, you will want to begin stopping sooner than you would on dry pavement. Without ABS, if you feel your vehicle begin to slide, let up on the brakes a little. Push the brake pedal down steadily to get the most traction you can.
{CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking your exhaust pipe. And check around again from time to time to be sure snow does not collect there. You can run the engine to keep warm, but be careful.
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Rocking Your Vehicle to Get It Out Loading Your Vehicle First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has traction control, you should turn your traction control system off. See Traction Control System (TCS) on page 4-9. Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible.
Tire and Loading Information Label The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inflation pressures (D). For more information on tires and inflation see Tires on page 5-51 and Inflation - Tire Pressure on page 5-57. There is also important loading information on the vehicle Certification/Tire label. It tells you the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for the front and rear axle.
4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6.
Example 2 Item A B C Description Total Vehicle Capacity Weight 1,000 lbs (453 kg) for Example 2 = Subtract Occupant Weight 150 lbs 750 lbs (340 kg) (68 kg) × 5 = Available Cargo Weight = 250 lbs (113 kg) Example 3 Item A B C Description Total Vehicle Capacity Weight 1,000 lbs (453 kg) for Example 3 = Subtract Occupant Weight 200 lbs 1,000 lbs (453 kg) (91 kg) × 5 = Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle’s tire and loading information label for specific information about your vehicle
Certification/Tire Label The label shows the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this.
Never exceed the GVWR for your vehicle or the GAWR for either the front or rear axle. {CAUTION: Do not load your vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle. Notice: Overloading your vehicle may cause damage.
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-6. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing” following. Recreational Vehicle Towing Recreational vehicle towing means towing your vehicle behind another vehicle – such as behind a motorhome.
Dinghy Towing Your vehicle was not designed to be towed with all of its wheels on the ground. If you have a two-wheel-drive vehicle, it can be towed with the two rear wheels on the ground. See “Dolly Towing” following. If you have an all-wheel-drive vehicle, it cannot be towed with any of its wheels on the ground. It can be towed with car carrier equipment.
Towing a Trailer {CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured. Pull a trailer only if you have followed all the steps in this section. Ask your dealer for advice and information about towing a trailer with your vehicle.
If You Do Decide To Pull A Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving. A good source for this information can be state or provincial police. • Consider using a sway control. See “Hitches” later in this section. • Do not tow a trailer at all during the first 500 miles (800 km) your new vehicle is driven.
Axle Ratio Maximum Trailer Weight *GCWR Two-Wheel-Drive (Short Wheel Base) 3.29 2,000 lbs (907 kg) 7,000 lbs (3 175 kg) Two-Wheel-Drive (Long Wheel Base) 3.29 3,500 lbs (1 588 kg) 8,500 lbs (3 856 kg) All-Wheel Drive 3.29 3,500 lbs (1 588 kg) 8,500 lbs (3 856 kg) Vehicle *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversion.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle. If you have a lot of options, equipment, passengers, or cargo in your vehicle, it will reduce the tongue weight your vehicle can carry, which will also reduce the trailer weight your vehicle can tow.
Hitches Safety Chains It is important to have the correct hitch equipment. Crosswinds, large trucks going by, and rough roads are a few reasons why you will need the right hitch. Here are some rules to follow: You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch.
Driving with a Trailer {CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You cannot see or smell CO. It can cause unconsciousness or death. See Engine Exhaust on page 2-41. To maximize your safety when towing a trailer: • Have your exhaust system inspected for leaks, and make necessary repairs before starting on your trip. • Keep the rear-most windows closed.
Passing Turn Signals When Towing a Trailer You will need more passing distance up ahead when you are towing a trailer. And, because you are a good deal longer, you will need to go much farther beyond the passed vehicle before you can return to your lane. When you tow a trailer, your vehicle has to have extra wiring. Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, just move that hand to the left.
Parking on Hills {CAUTION: You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged. But if you ever have to park your rig on a hill, do the following: 1. Apply your regular brakes, but do not shift into PARK (P). 2. Have someone place chocks under the trailer wheels. 3.
Section 5 Service and Appearance Care Service ............................................................5-3 Doing Your Own Service Work .........................5-4 Adding Equipment to the Outside of Your Vehicle ......................................................5-5 Fuel ................................................................5-5 Gasoline Octane ............................................5-5 Gasoline Specifications ....................................5-5 California Fuel ....................
Section 5 Service and Appearance Care Wheel Replacement ......................................5-63 Tire Chains ..................................................5-64 Accessory Inflator .........................................5-65 If a Tire Goes Flat ........................................5-67 Changing a Flat Tire .....................................5-68 Removing the Spare Tire and Tools ................5-69 Removing the Flat Tire and Installing the Spare Tire ...........................................
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-11. Your vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-85.
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle. Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. Gasoline Octane A little pinging noise when you accelerate or drive uphill is considered normal.
California Fuel Additives If your vehicle is certified to meet California Emission Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be affected.
Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber parts. That damage would not be covered under your warranty. Some gasolines that are not reformulated for low emissions may contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT.
Filling the Tank {CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling your vehicle — this is against the law in some places.
{CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way. Be careful not to spill fuel. Do not top off or overfill the tank and wait a few seconds after you have finished pumping before removing the nozzle.
Filling a Portable Fuel Container Checking Things Under the Hood {CAUTION: Never fill a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense gasoline only into approved containers. • Do not fill a container while it is inside a vehicle, in a vehicle’s trunk, pickup bed, or on any surface other than the ground.
Hood Release 3. Lift the hood. To open the hood, do the following: 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver’s side. 2. Go to the front of the vehicle and push the underhood release to the right. It is located near the center of the hood, above the grille. 4. Pull up on the hood prop to release it from its storage clip. The hood prop may be hot due to increased engine temperatures under the hood, so be careful when handling it.
Engine Compartment Overview When you open the hood, here is what you will see: 5-12
A. Underhood Fuse Block. See Underhood Fuse Block on page 5-98. B. Remote Positive (+) Terminal. See Jump Starting on page 5-39. C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-35. D. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-24. E. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-34. F. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-13. G. Engine Oil Dipstick.
When to Add Engine Oil If the oil is at or below the cross-hatched area at the tip of the dipstick, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-101. Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged.
What Kind of Engine Oil to Use • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container. This symbol indicates that the oil has been certified by the American Petroleum Institute (API).
Notice: Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty. GM Goodwrench® oil meets all the requirements for your vehicle. If you are in an area of extreme cold, where the temperature falls below −20°F (−29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil.
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL SOON message being turned on, reset the system. 1.
Engine Air Cleaner/Filter How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required. To inspect or replace the air cleaner/filter, do the following: 1. Remove the two clamps on the duct. 2. Remove the duct. 3. Unlatch the two hooks on top of the engine air cleaner/filter housing. 4.
Automatic Transaxle Fluid {CAUTION: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flame if the engine backfires. If it is not there and the engine backfires, you could be burned. Do not drive with it off, and be careful working on the engine with the air cleaner/filter off. Notice: If the air cleaner/filter is off, a backfire can cause a damaging engine fire.
How to Check Automatic Transaxle Fluid To get the right reading, the fluid should be at normal operating temperature, which is 180°F to 200°F (82°C to 93°C). Because this operation can be a little difficult, you may choose to have this done at the dealership service department. Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50°F (10°C). If it is colder than 50°F (10°C), you may have to drive longer.
Then, without shutting off the engine, follow these steps: How to Add Automatic Transaxle Fluid The automatic transaxle dipstick is located toward the back of the engine compartment, next to the brake master cylinder reservoir. The dipstick handle is a red loop. See Engine Compartment Overview on page 5-12 for more information on location. Refer to the Maintenance Schedule to determine what kind of transaxle fluid to use. See Recommended Fluids and Lubricants on page 6-12. 1.
Engine Coolant What Engine Coolant to Use The cooling system in your vehicle is filled with DEX-COOL® engine coolant. This coolant is designed to remain in your vehicle for five years or 150,000 miles (240 000 km), whichever occurs first, if you add only DEX-COOL® extended life coolant. Use a mixture of one-half clean, drinkable water and one-half DEX-COOL® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else.
Notice: If you use an improper coolant mixture, your engine could overheat and be badly damaged. The repair cost would not be covered by your warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core and other parts. If you have to add coolant more than four times a year, have your dealer check your cooling system. Notice: If you use the proper coolant, you do not have to add extra inhibitors or additives which claim to improve the system. These can be harmful.
Adding Coolant If you need more coolant, add the proper DEX-COOL® coolant mixture at the coolant recovery tank, but be careful not to spill it. {CAUTION: Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. With the coolant recovery tank, you will almost never have to add coolant at the radiator. Never turn the radiator pressure cap — even a little — when the engine and radiator are hot.
Engine Overheating You will find an engine coolant temperature gage on your vehicle’s instrument panel. See Engine Coolant Temperature Gage on page 3-39. Your vehicle may also have an ENGINE COOLANT HOT message displayed in the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-51. If Steam Is Coming From Your Engine {CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it.
If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: • Climb a long hill on a hot day. • Stop after high-speed driving. • Idle for long periods in traffic. • Tow a trailer. If you get the overheat warning with no sign of steam, try this for a minute or so: 1. If your air conditioner is on, turn it off. 2.
Overheated Engine Protection Operating Mode This emergency operating mode allows your vehicle to be driven to a safe place in an emergency situation. If an overheated engine condition exists, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, you will notice a significant loss in power and engine performance. The temperature gage will indicate an overheat condition exists.
{CAUTION: {CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface.
Notice: Engine damage from running your engine without coolant is not covered by your warranty. See Overheated Engine Protection Operating Mode on page 5-27 for information on driving to a safe place in an emergency. Notice: Using coolant other than DEX-COOL® may cause premature engine, heater core or radiator corrosion. In addition, the engine coolant may require changing sooner, at 30,000 miles (50 000 km) or 24 months, whichever occurs first. Any repairs would not be covered by your warranty.
Notice: In cold weather, water can freeze and crack the engine, radiator, heater core and other parts. Use the recommended coolant and the proper coolant mixture. When the coolant in the coolant recovery tank is at or above the full cold mark, start your vehicle. {CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.
How to Add Coolant to the Radiator Notice: Your engine has a specific radiator fill procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged. Turn the pressure cap slowly counterclockwise until it first stops. Do not press down while turning the pressure cap. If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left. 2. Then keep turning the pressure cap, but now push down as you turn it. Remove the pressure cap.
Housing Bypass Tube 3. After the engine cools, open the coolant air bleed valves. There are two bleed valves. One is located on the thermostat housing. The other is located on the thermostat bypass tube. 4. Fill the radiator with the proper DEX-COOL® coolant mixture, up to the base of the filler neck. See Engine Coolant on page 5-22 for more information about the proper coolant mixture. If you see a stream of coolant coming from an air bleed valve, close the valve.
6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. 9. Then fill the coolant recovery tank to the full cold mark. 10. Put the cap back on the coolant recovery tank. 7. By this time, the coolant level inside the radiator filler neck may be lower. If the level is lower, add more of the proper DEX-COOL® coolant mixture through the filler neck until the level reaches the base of the filler neck. 8. Then replace the pressure cap.
Power Steering Fluid See Engine Compartment Overview on page 5-12 for reservoir location. How to Check Power Steering Fluid To check the power steering fluid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag. 4. Replace the cap and completely tighten it. 5. Remove the cap again and look at the fluid level on the dipstick.
Windshield Washer Fluid What Washer Fluid to Use When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 5-12 for reservoir location.
Brakes Brake Fluid Your brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the fluid level goes back up. The other reason is that fluid is leaking out of the brake system.
Always clean the brake fluid reservoir cap and the area around the cap before removing it. This will help keep dirt from entering the reservoir. {CAUTION: With the wrong kind of fluid in your brake system, your brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper brake fluid. Notice: • Using the wrong fluid can badly damage brake system parts.
Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque specifications. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble.
Battery Jump Starting Your vehicle has a maintenance free battery. When it is time for a new battery, get one that has the replacement number shown on the original battery’s label. We recommend an ACDelco® replacement battery. Warning: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged.
The terminal is located under a tethered cap at the front of the underhood fuse block. See Engine Compartment Overview on page 5-12 for more information on location. Squeeze the tabs and swing the cap out of the way to access the remote positive (+) terminal. You should always use the remote positive (+) terminal instead of the positive (+) terminal on your battery. {CAUTION: {CAUTION: Using a match near a battery can cause battery gas to explode.
{CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one.
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal. To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2.
All-Wheel Drive How to Check Lubricant If you have an all-wheel-drive vehicle, be sure to perform the lubricant checks described in this section. All-wheel-drive vehicles have two additional systems that need lubrication. Transfer Case (Power Transfer Unit) When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See Scheduled Maintenance on page 6-4. To get an accurate reading, the vehicle should be on a level surface.
Carrier Assembly-Differential (Rear Drive Module) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See Scheduled Maintenance on page 6-4. How to Check Lubricant If the level is below the bottom of the filler plug hole, located on the differential, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the filler plug hole.
Bulb Replacement Headlamps and Sidemarker Lamps For the proper type of replacement bulbs, see Replacement Bulbs on page 5-49. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs {CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. 5-46 A. High-beam Headlamp B. Low-Beam Headlamp C.
To replace one of these bulbs, do the following: 1. Open the hood. See Hood Release on page 5-11 for more information. 4. Pull the assembly away from the vehicle. 5. Disconnect the socket wiring harness connector from the headlamp assembly. 6. Turn the bulb socket counterclockwise to remove from the assembly. 7. To replace a headlamp bulb, disconnect the bulb socket wiring harness and connect to the new bulb socket. To replace a sidemarker bulb, pull the old bulb out and push a new bulb in. 8.
Front Turn Signal, Parking and Daytime Running Lamps (DRL) Taillamps, Turn Signal, Stoplamps and Back-up Lamps To change a stoplamp/taillamp, turn signal or back-up lamp bulb, do the following: 1. Open the liftgate. See Liftgate on page 2-23 for more information. 2. Remove the two screws from the taillamp housing on the inboard side. To replace one of these bulbs (A), do the following: 1. Follow the Steps 1 through 4 to remove the headlamp assembly.
7. Replace the bulb socket by inserting and turning clockwise to secure. 8. Reinstall the taillamp assembly by inserting the outboard locating/retaining pins until the lamp is seated. 9. Secure with the inboard screws. Replacement Bulbs Exterior Lamp Back-up Front Turn Signal, DRL and Parking A. Stoplamp/Taillamp B. Turn Signal Lamp C. Back-up Lamp Bulb 5. Turn the bulb socket counterclockwise to remove.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear and cracking. See Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on page 6-14. To replace the windshield wiper blade assembly do the following: 1. Lift the wiper arm and turn the blade until it is facing away from the windshield. 2.
Tires CAUTION: Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner Manual. {CAUTION: • Underinflated tires pose the same danger • Poorly maintained and improperly used tires are dangerous.
Tire Sidewall Labelling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. (B) TPC Spec (Tire Performance Criteria Specification): Original equipment tires designed to GM’s specific tire performance criteria have a TPC specification code molded onto the sidewall. GM’s TPC specifications meet or exceed all federal safety guidelines.
(C) Tire Identification Number (TIN): The letters and numbers following the DOT (Department of Transportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire.
Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo. Accessory Weight: This means the combined weight of optional accessories.
Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight.
UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-61. Vehicle Capacity Weight: The number of designated seating positions multiplied by 150 lbs (68 kg) plus the rated cargo load. See Loading Your Vehicle on page 4-33.
A Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar), below the driver’s door latch. This label shows your vehicle’s original equipment tires and the correct inflation pressures for your tires when they are cold. The recommended cold tire inflation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity.
Tire Inspection and Rotation Do not include the compact spare tire in your tire rotation. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels.
When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.
Uniform Tire Quality Grading {CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle. Be sure to use the same size and type tires on all wheels. It’s all right to drive with your compact spare temporarily, it was developed for use on your vehicle. See Compact Spare Tire on page 5-85.
Treadwear Temperature – A, B, C The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment may need to be checked.
Used Replacement Wheels Tire Chains {CAUTION: {CAUTION: Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel. Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts.
Accessory Inflator This symbol is on the accessory inflator switch. Your vehicle may have an accessory inflator. With it, you can inflate things like air mattresses and basketballs, and you can also use it to bring your tires up to the proper pressure. The accessory inflator is located in the rear compartment on the driver’s side. To access the accessory inflator, do the following: 1. Open the liftgate. See Liftgate on page 2-23 for more information. 2.
To use your accessory inflator system, do the following: 1. Turn the ignition to ACCESSORY or RUN. 2. Attach the appropriate nozzle adapter, if required, to the end of the hose that has the pressure gage. 3. Attach that end of the hose to the object you wish to inflate. 4. Remove the protective cap covering the outlet. 5. Attach the other end of the hose to the outlet. 6. Press the accessory inflator switch. The light in the switch will come on to show the system is working.
If a Tire Goes Flat It is unusual for a tire to blowout while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your vehicle’s hazard warning flashers. When your vehicle has a flat tire, use the following example as a guide to assist you in the placement of wheel blocks. {CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire.
Removing the Spare Tire and Tools The tools you will need are located in the storage compartment at the rear of the vehicle, on the passenger’s side. To remove the tools, do the following: 1. Open the liftgate. See Liftgate on page 2-23 for more information. 2. Remove the convenience net, if equipped. 3. Open the jack storage compartment by lifting the tab and pulling the cover off. A. B. C. D. E. Jack Strap Bracket Wing Nut Jacking Instructions F. Bag and Tools G.
To remove the compact spare tire, do the following: The tools you will be using include the jack (A), extension (B), and folding wrench (C). The compact spare tire is located under the rear of the vehicle. See Compact Spare Tire on page 5-85 for more information about the compact spare. A. Hoist Shaft B. Hoist Assembly C. Retainer D. Compact Spare Tire E. Extension (Chisel End) F. Folding Wrench 1.
If you have a front-wheel-drive vehicle, the hoist is used to store a full-size or a flat road tire under the vehicle. See “Storing the Flat Tire on an Front-Wheel-Drive Vehicle” under Storing a Flat or Spare Tire and Tools on page 5-80 for more information. 4. Remove the compact spare tire from the cable. If the compact spare tire will not lower, check under the vehicle to see if the tire is hanging loose and the cable end and spring under the wheel plate are missing.
Removing the Flat Tire and Installing the Spare Tire If the wheel has a center cap, use the handle of the folding wrench to pry it off. Then, with the other end of the folding wrench, loosen the nuts. Once the center cap and/or wheel cover are removed, use the following steps to remove the flat tire and install the spare tire. 1. Loosen the wheel nuts — but do not remove them — using the folding wrench. Turn the handle counterclockwise about 180 degrees, then flip the handle back to the starting position.
Notice: If you position the jack under the rocker molding and attempt to raise the vehicle, you could break the molding and/or cause other damage to your vehicle. Always position the jack so that when the jack head is raised, it will fit firmly in the notch located inboard from the rocker molding. 3. Do not raise the vehicle yet. 4. Put the compact spare tire near you. {CAUTION: Getting under a vehicle when it is jacked up is dangerous.
5. Attach the folding wrench (A) to the jack (B), and turn the wrench clockwise to raise the jack head approximately 3 inches (7.6 cm). 5-74 6. Raise the vehicle by turning the folding wrench clockwise in the jack. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to fit under the wheel well.
8. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. 7. Remove all the wheel nuts and take off the flat tire. {CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle.
9. Install the compact spare tire and put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub. 5-76 10. Lower the vehicle by attaching the folding wheel wrench to the jack and turning the wrench counterclockwise. Lower the jack completely.
{CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See Capacities and Specifications on page 5-101 for wheel nut torque specification.
Secondary Latch System Your vehicle may have an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop a tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down. Your vehicle uses the underbody tire hoist assembly to store either the compact spare or a flat road tire.
To release the spare tire from the secondary latch, do the following: 1. Place the jack under the vehicle, ahead of the rear bumper. Position the center lift point of the jack under the center of the compact spare tire. 2. Turn the folding wrench clockwise to raise the jack until it lifts the secondary latch device under the wheel plate. 3. Keep raising the jack until the compact spare tire stops moving upward and is held firmly in place. This lets you know that the secondary latch has released. 4.
Storing a Flat or Spare Tire and Tools Storing the Flat Tire on an Front-Wheel-Drive Vehicle {CAUTION: {CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. The underbody-mounted spare tire needs to be stored with the valve stem pointing down.
To store the flat or spare tire and tools, do the following: 1. Lay the tire near the rear of the vehicle with the valve stem down. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels. 3. Slide the cable retainer through the center of the wheel and start to raise the tire. Make sure the retainer is fully seated across the underside of the wheel. 4.
Storing the Flat Tire on an All-Wheel-Drive Vehicle 1. Remove the tire storage bag and cable package from the jack storage area. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels. 3. Put the flat tire in the tire storage bag and place it in the rear storage area with the valve stem pointing toward the front of the vehicle. A. Cable B. Liftgate Hinges C. Door Striker 4.
5. Hook the cable onto the outside portion of the liftgate hinges. 6. Pull on the cable to make sure it is secure. 7. Make sure the metal tube is centered at the striker. Push the tube towards the front of the vehicle. 8. Close the liftgate and make sure it is latched properly.
Storing the Tools Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on. To put the cover back on, line up the tabs on the right of the cover with the slots in the cover opening. Push the cover in place and push down the tab so that it rests in the groove. This secures the cover in place. Store the center cap or the plastic bolt-on wheel covers until a full size tire is put back on the vehicle.
Compact Spare Tire Although the compact spare tire was fully inflated when the vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated.
Appearance Care Cleaning products can be hazardous. Some are toxic. Other cleaning products can burst into flames if a match is struck near them or if they get on a hot part of the vehicle. Some are dangerous if their fumes are inhaled in an enclosed space. When anything from a container is used to clean the vehicle, be sure to follow the manufacturer’s warnings and instructions. Always open the doors or windows of the vehicle when cleaning the inside.
Most stains can be removed with club soda water. To clean, use the following instructions: 1. For liquids: blot with a clean, soft, white cloth. For solids: remove as much as possible and then vacuum or brush. 2. Apply club soda water to a clean, soft, white cloth. Do not over-saturate; the cloth should not drip water. Using Cleaner on Fabric 1. First, try the cleaner on an area of the fabric that is not easily seen to make sure the cleaner does not affect the color of the fabric. 2.
Special Fabric Cleaning Problems Leather Stains caused by such things as catsup, black coffee, egg, fruit, fruit juice, milk, soft drinks, vomit, urine, and blood can be removed using the club soda water instructions given earlier in this section. If an odor lingers after cleaning vomit or urine, treat the area with a water and baking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water. Let dry.
Interior Plastic Components Use only a mild soap and water solution on a soft cloth or sponge. Commercial cleaners may affect the surface finish. Child Restraint Pad The built-in child restraint pad is attached to the seat frame with fastener strips. You can remove the pad and hand wash it with mild soap and water. Glass Surfaces Notice: If you use abrasive cleaners when cleaning glass surfaces on your vehicle, you could scratch the glass.
Washing Your Vehicle Finish Care The paint finish on the vehicle provides beauty, depth of color, gloss retention, and durability. Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 5-93. The best way to preserve the vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water.
Windshield, Backglass, and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid. The windshield is clean if beads do not form when you rinse it with water. Grime from the windshield will stick to the wiper blades and affect their performance.
Tires Underbody Maintenance To clean the tires, use a stiff brush with tire cleaner. Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires.
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Description Usage Polishing Cloth Wax-Treated Interior and exterior polishing cloth. Tar and Road Oil Remover Removes tar, road oil, and asphalt. Chrome Cleaner and Polish Use on chrome or stainless steel. White Sidewall Tire Cleaner Removes soil and black marks from whitewalls. Vinyl Cleaner Cleans vinyl.
Vehicle Identification Engine Identification Vehicle Identification Number (VIN) The eighth character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts. Service Parts Identification Label You will find this label on the inside of the glove box. It is very helpful if you ever need to order parts. On this label, you will find the following: • • • • This is the legal identifier for your vehicle.
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-85.
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible thermal links. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.
Fuses Usage Fuses Usage 1 Trunk, Door Locks 20 Park Lamps 2 Electronic Level Control 21 Power Sliding Door 3 Rear Wiper 22 Blank 4 Radio Amplifier 23 Blank 5 Interior Lamps 24 Left Power Sliding Door 6 OnStar® 25 Right Power Sliding Door 7 Keyless Entry Module 8 Cluster, Heating, Ventilation, Air-Conditioning 9 Cruise Switch 10 Steering Wheel Illumination 11 Power Mirror 12 Stoplamp, Turn Lamps 13 Heated Seats 14 Blank 15 Electronic Level Control 16 Heated Mirr
Underhood Fuse Block The underhood fuse block is located in the engine compartment. For more information on location see Engine Compartment Overview on page 5-12. Your vehicle may not have all the fuses listed.
Fuses Usage Fuses Usage 1 Right High Beam 13 Anti-lock Brake System 2 Fuel Pump 14 Powertrain Control Module Ignition 3 Diode 15 Electronic Ignition SPARE Spare 16 Fuel Injector SPARE Spare 17 Climate Control, RPA, Cruise Control 18 Electronic Throttle Control 19 Engine Sensor, Evaporator 20 Airbag 21 Not Used 22 Emission, All-Wheel Drive 23 Auxiliary Power 24 Front Windshield Washer 25 AC/DC Inverter 26 Rear Blower 4 Left High Beam SPARE Spare SPARE Spare SPA
J-Case Fuses PLR Usage Relays Fuse Puller RUN RLY Starter 29 Fan 1 LO BEAM Low Beam 30 Starter Solenoid FUEL PUMP Fuel Pump 31 Anti-lock Brake System Motor 32 Blank 33 Fan 2 HI BEAM High Beam 34 Front Blower High PWR/TRN Powertrain 35 Battery Main 3 WPR2 Wiper 2 36 Rear Defogger WPR1 Wiper 1 37 Battery Main 2 FAN 1 Fan 1 38 Battery Main 1 CRNK Crank HORN AC/CLTCH IGN MAIN Horn Air-Conditioning Clutch Ignition Main FAN2 Fan 2 FAN3 Fan 3 BLANK 5-100 Usage N
Capacities and Specifications The following approximate capacities are given in English and metric measurements. See Recommended Fluids and Lubricants on page 6-12 for more information. Capacities Application Metric Air Conditioning Refrigerant Systems Front A/C 1.7 lbs 0.8 kg Front and Rear A/C 2.2 lbs 1.0 kg Automatic Transaxle – Pan Removal and Replacement 7.4 quarts 7.0 L AWD Automatic Transaxle – Pan Removal and Replacement 8.7 quarts 8.3 L Cooling System Front A/C 11.3 quarts 10.
✍ NOTES 5-102
Section 6 Maintenance Schedule Maintenance Schedule ......................................6-2 Introduction ...................................................6-2 Maintenance Requirements ..............................6-2 Your Vehicle and the Environment ....................6-2 Using the Maintenance Schedule ......................6-2 Scheduled Maintenance ...................................6-4 Additional Required Services ............................6-6 Maintenance Footnotes ...............................
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle.
This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will find these limits on the tire and loading information label. See Loading Your Vehicle on page 4-33. • are driven on reasonable road surfaces within legal driving limits. • use the recommended fuel. See Gasoline Octane on page 5-5. The services in Scheduled Maintenance on page 6-4 should be performed when indicated.
Scheduled Maintenance When the CHANGE OIL SOON message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, your engine oil and filter must be changed at least once a year and at this time the system must be reset.
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. See Engine Oil on page 5-13. Reset oil life system. See Engine Oil Life System on page 5-16. An Emission Control Service. • • Lubricate chassis components. See footnote #. • • Visually check for any leaks or damage. See footnote (k). • • Inspect engine air cleaner filter. If necessary, replace filter. See Engine Air Cleaner/Filter on page 5-18. An Emission Control Service. See footnotes † and (g).
Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Additional Required Services 25,000 (41 500) 50,000 (83 000) 75,000 (125 000) 100,000 (166 000) 125,000 (207 500) 150,000 (240 000) Inspect fuel system for damage or leaks. • • • • • • Inspect exhaust system for loose or damaged components.
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
(f) Lubricate all key lock cylinders, hood latch assemblies, secondary latches, pivots, spring anchor and release pawl, hood and door hinges, rear folding seats, liftgate hinges, fuel door hinge, power sliding door cable and sliding door track(s). More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better and not stick or squeak. (i) Drain, flush and refill cooling system.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Your GM Goodwrench® dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 6-12.
At Least Once a Year Starter Switch Check {CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. Automatic Transaxle Shift Lock Control System Check {CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. 1. Before you start, be sure you have enough room around the vehicle.
Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK in each shift lever position. • The ignition should turn to LOCK only when the shift lever is in PARK (P). • The key should come out only in LOCK. Contact your GM Goodwrench® dealer if service is required. Parking Brake and Automatic Transaxle Park (P) Mechanism Check {CAUTION: When you are doing this check, your vehicle could begin to move.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. GM Goodwrench® oil meets all the requirements for your vehicle. To determine the proper viscosity for your vehicle’s engine, see Engine Oil on page 5-13.
Usage Fluid/Lubricant Carrier Assembly — Differential (Rear Drive Module) and Transfer Case (Power Transfer Unit) VERSATRAK® Fluid (GM Part No. U.S. 12378514, in Canada 88901045). Hood Latch Assembly, Secondary Latch, Pivots, Spring Anchor and Release Pawl Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer. GM Part Number ACDelco® Part Number Engine Air Cleaner/Filter 12565752 A-2946C Engine Oil Filter 25010792 PF-47 Spark Plugs 12568387 41-101 Driver’s Side — 22.0 inches (55.0 cm) 15192143 — Passenger’s Side — 24.0 inches (60.0 cm) 15192144 — Rear — 16.0 inches (40.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Maintenance Record (cont’d) Date 6-16 Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-17
Maintenance Record (cont’d) Date 6-18 Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed
Section 7 Customer Assistance and Information Customer Assistance and Information ...............7-2 Customer Satisfaction Procedure ......................7-2 Online Owner Center ......................................7-3 Customer Assistance for Text Telephone (TTY) Users ...............................................7-4 Customer Assistance Offices ............................7-4 GM Mobility Reimbursement Program ................7-5 Roadside Assistance Program ..........................
Customer Assistance and Information We encourage you to call the toll-free number in order to give your inquiry prompt attention. Please have the following information available to give the Customer Assistance Representative: Customer Satisfaction Procedure • Vehicle Identification Number (VIN). This is Your satisfaction and goodwill are important to your dealer and to Chevrolet.
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to filing a court action, use of the program is free of charge and your case will generally be heard within 40 days.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Chevrolet by dialing: 1-800-833-CHEV (2438). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. If a U.S.
Overseas — Customer Assistance Please contact the local General Motors Business Unit. GM Mobility Reimbursement Program Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance This program, available to qualified applicants, can reimburse you up to $1,000 toward eligible aftermarket driver’s or passenger’s adaptive equipment you may require for your vehicle, such as hand controls and wheelchair/scooter lifts. General Motors de Mexico, S.
Roadside Assistance Program As the owner of a new Chevrolet vehicle, you are automatically enrolled in the Chevrolet Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road. Call Chevrolet’s Roadside Assistance at 1-800-CHEV-USA, (1-800-243-8872) 24 hours a day, 365 days a year to speak with a Chevrolet Roadside Assistance representative.
While we hope you never have the occasion to use our service, it is added security while traveling for you and your family. Remember, we are only a phone call away. Chevrolet Roadside Assistance: 1-800-CHEV-USA (1-800-234-8872), text telephone (TTY) users, call 1-888-889-2438. Chevrolet reserves the right to limit services or reimbursement to an owner or driver when, in Chevrolet’s judgement, the claims become excessive in frequency or type of occurrence.
Transportation Options Courtesy Rental Vehicle Warranty service can generally be completed while you wait. However, if you are unable to wait, Chevrolet helps minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for a warranty repair.
Additional Program Information Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but it is not part of the New Vehicle Limited Warranty. A separate booklet entitled “Warranty and Owner Assistance Information” furnished with each new vehicle provides detailed warranty coverage information. Courtesy Transportation is available only at participating GM dealers and all program options, such as shuttle service, may not be available at every dealer.
To read this information, special equipment is needed and access to the vehicle or the device that stores the data is required. GM will not access information about a crash event or share it with others other than: • with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee, • in response to an official request of police or similar government office, • as part of GM’s defense of litigation through the discovery process, or • as required by law.
Reporting Safety Defects to the Canadian Government Service Publications Ordering Information If you live in Canada, and you believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited.
Owner’s Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner’s Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00 Without Portfolio: Owner’s Manual only. RETAIL SELL PRICE: $25.
A Accessory Inflator ........................................... 5-65 Accessory Power Outlets ................................. 3-23 Adding Equipment to Your Airbag-Equipped Vehicle ....................................................... 1-86 Additives, Fuel ................................................. 5-6 Add-On Electrical Equipment ............................ 5-95 Air Cleaner/Filter, Engine ................................. 5-18 Air Conditioning ..............................................
Audio System(s) ............................................. 3-76 Audio Steering Wheel Controls .................... 3-112 Care of Your CD and DVD Player ................ 3-114 Care of Your CDs and DVDs ....................... 3-114 Fixed Mast Antenna ................................... 3-114 Radio with CD ............................................ 3-77 Rear Seat Audio (RSA) ............................... 3-109 Setting the Time .......................................... 3-76 Theft-Deterrent Feature ....
Chains, Tire ................................................... Charging System Light .................................... Check Engine Light ............................................... Checking Things Under the Hood ...................... Chemical Paint Spotting ................................... Child Restraints Built-In Child Restraint .................................. Child Restraint Systems ............................... Infants and Young Children ...........................
Cupholder(s) .................................................. 2-51 Customer Assistance Information Courtesy Transportation .................................. 7-7 Customer Assistance for Text Telephone (TTY) Users ............................... 7-4 Customer Assistance Offices ........................... 7-4 Customer Satisfaction Procedure ..................... 7-2 GM Mobility Reimbursement Program ............... 7-5 Reporting Safety Defects to General Motors .......
E Electrical System Add-On Equipment ...................................... 5-95 Fuses and Circuit Breakers ........................... 5-96 Headlamp Wiring ......................................... 5-95 Instrument Panel Fuse Block ......................... 5-96 Power Windows and Other Power Options ...... 5-95 Underhood Fuse Block ................................. 5-98 Windshield Wiper Fuses ............................... 5-95 Engine Air Cleaner/Filter .........................................
Fuel (cont.) Filling Your Tank ........................................... 5-8 Fuels in Foreign Countries .............................. 5-7 Gage ......................................................... 3-44 Gasoline Octane ........................................... 5-5 Gasoline Specifications .................................. 5-5 Low Warning Light ....................................... 3-44 Fuses Fuses and Circuit Breakers ........................... 5-96 Instrument Panel Fuse Block ...................
Hood Checking Things Under ................................ 5-10 Release ..................................................... 5-11 Horn ............................................................... 3-6 How to Use This Manual ...................................... ii How to Wear Safety Belts Properly ................... 1-27 I Ignition Positions ............................................. 2-32 Infants and Young Children, Restraints ............... 1-43 Inflation -- Tire Pressure .......................
Light (cont.) Safety Belt Reminder ................................... Security ..................................................... TCS Warning Light ...................................... Traction Control System (TCS) Warning .......... Lighting Delayed ..................................................... Entry ......................................................... Exit ........................................................... Loading Your Vehicle .......................................
N P New Vehicle Break-In ...................................... 2-31 Normal Maintenance Replacement Parts ............ 6-14 Park Aid ........................................................ 3-21 Park (P) Shifting Into ................................................ 2-39 Shifting Out of ............................................ 2-40 Parking Assist ........................................................ 3-21 Brake ........................................................ 2-38 Over Things That Burn ....
Q Questions and Answers About Safety Belts ......... 1-26 R Radiator Pressure Cap .................................... 5-24 Radios .......................................................... 3-76 Care of Your CD and DVD Player ................ 3-114 Care of Your CDs and DVDs ....................... 3-114 Radio with CD ............................................ 3-77 Rear Seat Audio ........................................ 3-109 Setting the Time ..........................................
S Safety Belt Pretensioners .............................................. 1-41 Reminder Light ............................................ 3-33 Safety Belts Care of Safety Belts and Built-in Child Restraint Harness ............................ 5-89 Driver Position ............................................ 1-27 How to Wear Safety Belts Properly ................ 1-27 Questions and Answers About Safety Belts ........ 1-26 Rear Safety Belt Comfort Guides for Children and Small Adults .......................
Sliding Doors, Dual ......................................... 2-14 Spare Tire Installing .................................................... 5-72 Removing ................................................... 5-69 Storing ....................................................... 5-80 Specifications, Capacities ............................... 5-101 Speedometer .................................................. 3-33 StabiliTrak® System ......................................... 4-10 Starting Your Engine .........
Tires (cont.) Secondary Latch System .............................. 5-78 Storing a Flat or Spare Tire and Tools ............ 5-80 Tire Sidewall Labelling .................................. 5-52 Tire Terminology and Definitions .................... 5-55 Uniform Tire Quality Grading ......................... 5-61 Wheel Alignment and Tire Balance ................. 5-63 Wheel Replacement ..................................... 5-63 When It Is Time for New Tires ...................... 5-60 Top Strap ..............
W Warning Lights, Gages and Indicators ................ 3-31 Warnings DIC Warnings and Messages ........................ 3-51 Hazard Warning Flashers ............................... 3-6 Other Warning Devices .................................. 3-6 Safety and Symbols ......................................... iii Vehicle Damage .............................................. iv Wheels Alignment and Tire Balance .......................... 5-63 Replacement ...............................................
