2007 Chevrolet Colorado Owner Manual Seats and Restraint Systems ....................... 7 Front Seats .............................................. 9 Rear Seats ............................................. 17 Safety Belts ............................................ 20 Child Restraints ...................................... 43 Airbag System ........................................ 76 Restraint System Check ......................... 94 Features and Controls ................................ 97 Keys .......
Service and Appearance Care .................. Service ................................................. Fuel ...................................................... Checking Things Under the Hood ......... Rear Axle ............................................. Four-Wheel Drive .................................. Front Axle ............................................ Bulb Replacement ................................ Windshield Wiper Blade Replacement ... Tires ...............................................
This manual describes features that may be available in this model, but your vehicle may not have all of them. For example, more than one entertainment system may be offered or your vehicle may have been ordered without a front passenger or rear seats. GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, and the name COLORADO are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed.
How to Use This Manual Many people read the owner manual from beginning to end when they first receive their new vehicle. If this is done, it can help you learn about the features and controls for the vehicle. Pictures and words work together in the owner manual to explain things. Index A good place to quickly locate information about the vehicle is the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found.
Vehicle Damage Warnings Vehicle Symbols Also, in this manual you will find these notices: The vehicle has components and labels that use symbols instead of text. Symbols are shown along with the text describing the operation or information relating to a specific component, control, message, gage, or indicator. Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle.
These are some examples of symbols that may be found on the vehicle: 6
Section 1 Seats and Restraint Systems Front Seats ..................................................... 9 Manual Seats ................................................ 9 Power Seats ............................................... 10 Manual Lumbar ........................................... 10 Power Lumbar ............................................. 11 Heated Seats .............................................. 11 Reclining Seatbacks .................................... 12 Head Restraints ...............
Section 1 Seats and Restraint Systems Airbag System .............................................. 76 Where Are the Airbags? .............................. 79 When Should an Airbag Inflate? .................. 82 What Makes an Airbag Inflate? ................... 84 How Does an Airbag Restrain? ................... 84 What Will You See After an Airbag Inflates? ........................................ 85 Passenger Sensing System ......................... 86 8 Servicing Your Airbag-Equipped Vehicle ......
Front Seats Manual Seats {CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving. Lift the bar located under the front of the seat to unlock it. Slide the seat to where you want it and release the bar. Try to move the seat with your body to make sure the seat is locked into place.
• Raise or lower the entire seat by moving the Power Seats If the vehicle has power seats, the controls used to operate them are located on the outboard side of the seats. entire horizontal control up or down. • Use the vertical control to recline the seatback. See “Power Reclining Seatbacks” under Reclining Seatbacks on page 12 for more information. Manual Lumbar If your vehicle has this feature, there is a knob located on the outboard side of the driver’s seat.
Power Lumbar Heated Seats If your vehicle has this feature, the control is located on the outboard side of the seat(s). Press and hold the front of the control until you have the desired lumbar support. To decrease lumbar support, press and hold the rear of the control. If your vehicle has this feature, the controls are located on the outboard side of the front seats. This feature will heat the cushion and back of the seats. Press the top of the switch to turn the heat to the high setting.
Reclining Seatbacks Manual Reclining Seatbacks If your seats have manual reclining seatbacks, the lever used to operate them is located on the outboard side of the seat(s). {CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
To return the seatback to an upright position, do the following: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked. Power Reclining Seatbacks If the seats have power reclining seatbacks, use the vertical power seat control located on the outboard side of the seat. • To recline the seatback, press the control toward the rear of the vehicle.
{CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job because it will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt cannot do its job either. In a crash, the belt could go up over your abdomen.
Head Restraints Your front seats may have adjustable head restraints. If your vehicle has rear seats, they may have adjustable head restraints. Pull up on the head restraint to raise it. To lower the head restraint, press the button located on top of the seatback and push down on the head restraint. Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash.
Seatback Latches Your vehicle may have front seatbacks that fold forward for easy access to the rear seats or the storage area behind the seats. To fold the seatback forward, push the lever on the side of the seat rearward and pull the seatback forward. {CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked.
Rear Seats To store the seat, do the following: Rear Seat Operation (Extended Cab) If your vehicle has an extended cab, there may be forward folding seats in the rear area. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.
Rear Seat Operation (Crew Cab) To fold the rear seatback(s) forward, do the following: The rear seatback(s) in the crew cab can be folded forward. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. 1.
2. Pull the loop, located on the outboard side of the seatback, forward until you hear a click. 3. Fold the seatback(s) forward. To return the seatback(s) to the upright position, do the following: 1. Lift the seatback(s) and push it into place. {CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked. 2.
Safety Belts {CAUTION: Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. {CAUTION: Do not let anyone ride where he or she cannot wear a safety belt properly. If you are in a crash and you are not wearing a safety belt, your injuries can be much worse. You can hit things inside the vehicle or be ejected from it. You can be seriously injured or killed.
In most states and in all Canadian provinces, the law says to wear safety belts. Here is why: They work. You never know if you will be in a crash. If you do have a crash, you do not know if it will be a bad one. Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away.
Put someone on it. 22 Get it up to speed. Then stop the vehicle. The rider does not stop.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel...
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after an accident if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But you can unbuckle a safety belt, even if you are upside down. And your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers. Most accidents occur within 25 miles (40 km) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 km/h).
4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 42. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. Move the shoulder belt height adjuster to the height that is right for you. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash.
6. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Q: What is wrong with this? {CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. A: The shoulder belt is too loose. It will not give nearly as much protection this way.
Q: What is wrong with this? {CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force at your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs. A: The lap belt is too loose. It will not give nearly as much protection this way.
Q: What is wrong with this? {CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. A: The belt is buckled in the wrong place.
Q: What is wrong with this? {CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen. A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times.
Q: What is wrong with this? {CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it. A: The belt is twisted across the body.
Shoulder Belt Height Adjustment Before you begin to drive, move the shoulder belt height adjuster to the height that is right for you. Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should be away from your face and neck, but not falling off your shoulder. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. To unlatch the belt, push the button on the buckle. The belt should go back out of the way.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Center Front Passenger Position Lap Belt If your vehicle has a 60/40 split front seat, someone can sit in the center position. To make the belt shorter, pull its free end as shown until the belt is snug. Buckle, position and release it the same way as the lap part of a lap-shoulder belt. If the belt is not long enough, see Safety Belt Extender on page 42. When you sit in the center front seating position, you have a lap safety belt, which has no retractor.
Rear Seat Passengers It is very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who are not safety belted can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts. Lap-Shoulder Belt All rear seating positions have lap-shoulder belts. Here is how to wear one properly. 36 1.
2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again. If the belt is not long enough, see Safety Belt Extender on page 42. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 3. To make the lap part tight, pull up on the shoulder part.
The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The safety belt locks if there is a sudden stop or a crash. {CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. The lap part of the belt should be worn low and snug on the hips, just touching the thighs.
Rear Safety Belt Comfort Guides Your vehicle may have rear shoulder belt comfort guides for the rear outside positions. Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head. Here is how to install a comfort guide to the shoulder belt. To unlatch the belt, just push the button on the buckle.
2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt and insert the two edges of the belt into the slots of the guide. 40 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.
{CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. 4. Buckle, position, and release the safety belt as described in Rear Seat Passengers on page 36. Make sure that the shoulder belt crosses the shoulder.
Safety Belt Pretensioners Safety Belt Extender Your vehicle has safety belt pretensioners for the driver and right front passenger. Although you cannot see them, they are part of the safety belt assembly. They help tighten the safety belts during the early stages of a moderate to severe frontal or near frontal crash if the threshold conditions for pretensioner activation are met. If the vehicle’s safety belt will fasten around you, you should use it. Pretensioners work only once.
Child Restraints Older Children Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. It should never be worn over the abdomen, which could cause severe or even fatal internal injuries in a crash.
Q: What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? A: If the child is sitting in a seat next to a window, move the child toward the center of the vehicle. Also see Rear Safety Belt Comfort Guides on page 39. If the child is sitting in the center rear seat passenger position, move the child toward the safety belt buckle.
{CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen. That could cause serious or fatal injuries. Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs.
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
CAUTION: (Continued) Neither the vehicle’s safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide. {CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants.
Q: What are the different types of add-on child restraints? {CAUTION: A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available.
Child Restraint Systems {CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure. This alone could cause serious or fatal injuries.
A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. 50 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Q: How Should I Use a Child Restraint? A: A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner. To help reduce injuries, an add-on child restraint must be secured in the vehicle. With built-in or add-on child restraints, the child has to be secured within the child restraint.
Securing an Add-on Child Restraint in the Vehicle {CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Make sure the child restraint is properly installed in the vehicle using the vehicle’s safety belt or LATCH system, following the instructions that came with that restraint, and also the instructions in this manual. To help reduce the chance of injury, the child restraint must be secured in the vehicle.
Securing the Child Within the Child Restraint There are several systems for securing the child within the child restraint. One system, the three-point harness, has straps that come down over each of the infant’s shoulders and buckle together at the crotch. The five-point harness system has two shoulder straps, two hip straps, and a crotch strap. A shield may take the place of hip straps. A T-shaped shield has shoulder straps that are attached to a flat pad which rests low against the child’s body.
There is a label on your sun visor that says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great if the airbag deploys. {CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
{CAUTION: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. Be sure the airbag is off before using a rear-facing child restraint in the right front seat position. If you need to secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go.
Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle — even when no child is in it. Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier.
Lower Anchors Top Tether Anchor Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle.
Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. In the United States, some child restraints also have a top tether. Be sure to read and follow the instructions for your child restraint.
i (Top Tether Anchor): Seating positions with top tether anchors. For extended cab models with rear seats, there are exposed metal lower anchors for each rear seating position, attached to the back wall, near the seat cushion. To assist you in locating the lower anchors, place your hand in a palm-up position and reach up between the seat cushion and the seatback.
Crew Cab The top tether anchors in a crew cab model are located on the back wall behind each rear seating position. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed. 60 Extended Cab — Rear Seat The top tether anchors in an extended cab model are located on the center of the back wall behind a removable cover for the rear seating positions.
Do not secure a child restraint in the right front passenger’s position of a vehicle that has rear seats if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. There is no place to attach the top tether in this position. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat.
Securing a Child Restraint Designed for the LATCH System {CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came with that restraint, and also the instructions in this manual.
{CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Secure any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed. Be sure to follow the instructions of the child restraint manufacturer.
Crew Cab — Rear Seat 2.2. Route the top tether according to your child restraint instructions and the following instructions: If the position you are using has a fixed head restraint and you are using a single tether, route the tether over the head restraint. 1. Put the child restraint on the seat. 2. If the child restraint manufacturer’s instructions recommends that the top tether be attached, attach the top tether to the top tether anchor (A).
If the position you are using has a fixed or adjustable head restraint and you are using a dual tether, route the tether around the head restraint. 2.3. Attach the top tether to the anchor (A). Make sure that you secure the top tether to the top tether anchor and not to the seatback latch (B). 2.4. Push rearward on the seatback until it locks into its upright position. Push and pull on the seatback to make sure it is secured properly. 3. Attach and tighten the lower attachments to the lower anchors.
Extended Cab — Rear Seat 1. Attach and tighten the lower attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts. Refer to your child restraint manufacturer instructions and the instructions in this manual. 1.1. Find the lower anchors (D) for the desired seating position. 1.2. Put the child restraint on the seat. 66 1.3.
3. Tighten the lower anchor attachments and the top tether. The child restraint instructions will show you how. 4. Push and pull the child restraint in different directions to be sure it is secure. Front Seat — Regular/Extended Cab without Rear Seats Your vehicle has a right front passenger’s airbag and a passenger sensing system.
If the position you are using has an adjustable head restraint and you are using a single tether, raise the head restraint and route the tether under the head restraint and in between the head restraint posts. If the position you are using has a fixed or adjustable head restraint and you are using a dual tether, route the tether around the head restraint. 3. Attach and tighten the top tether according to your child restraint instructions. 4.
3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. If your child restraint has a top tether, attach the top tether to the top tether anchor. See Lower Anchors and Tethers for Children (LATCH) on page 56.
7. Tighten the top tether to the anchor. See Lower Anchors and Tethers for Children (LATCH) on page 56. 8. Push and pull the child restraint in different directions to be sure it is secure. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor.
Securing a Child Restraint in the Center Front Seat Position {CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the right front passenger’s airbag if it inflates. Never secure a child restraint in the center front seat. It is always better to secure a child restraint in the rear seat. Do not use child restraints in this position. Securing a Child Restraint in the Right Front Seat Position Your vehicle has a right front passenger’s airbag.
There is a label on your sun visor that says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. {CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
CAUTION: {CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. Be sure the airbag is off before using a rear-facing child restraint in the right front seat position.
You will be using the lap-shoulder belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. 1. Your vehicle has a right front passenger’s frontal airbag. See Passenger Sensing System on page 86. We recommend that rear-facing child restraints be secured in a rear seat, even if the airbag is off.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. If your vehicle does not have rear seats and if your child restraint has a top tether, attach the top tether to the top tether anchor. See Lower Anchors and Tethers for Children (LATCH) on page 56. 7. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor.
9. Push and pull the child restraint in different directions to be sure it is secure. 10. If the airbag is off, the off indicator on the instrument panel will be lit and stay lit when the key is turned to ON or START. If a child restraint has been installed and the on indicator is lit, turn the vehicle off. Remove the child restraint from the vehicle and reinstall the child restraint.
Airbags are designed to supplement the protection provided by safety belts. Even though today’s airbags are also designed to help reduce the risk of injury from the force of an inflating bag, all airbags must inflate very quickly to do their job. Here are the most important things to know about the airbag system: {CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags.
{CAUTION: {CAUTION: Both frontal and side impact airbags inflate with great force, faster than the blink of an eye. If you are too close to an inflating airbag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for airbag inflation before and during a crash. Always wear your safety belt even with frontal airbags. The driver should sit as far back as possible while still maintaining control of the vehicle.
There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. Where Are the Airbags? The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 183 for more information. The driver’s airbag is in the middle of the steering wheel.
The right front passenger’s airbag is in the instrument panel on the passenger’s side. 80 If your vehicle has a roof-mounted side impact airbag for the driver and the person seated directly behind the driver, it is located in the ceiling above the side windows.
{CAUTION: If your vehicle has a roof-mounted side impact airbag for the right front passenger and the person seated directly behind that passenger, it is located in the ceiling above the side windows. If something is between an occupant and an airbag, the bag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear.
When Should an Airbag Inflate? The driver’s and right front passenger’s frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in time for the airbags to inflate and help restrain the occupants.
Frontal airbags (driver and right front passenger) are not intended to inflate during vehicle rollovers, rear impacts, or in many side impacts. If your vehicle has side impact airbags, it has electronic side sensors. The side impact airbags are intended to inflate in moderate to severe side crashes. A side impact airbag will inflate if the crash severity is above the system’s designed “threshold level.” The threshold level can vary with specific vehicle design.
What Makes an Airbag Inflate? In an impact of sufficient severity, the airbag sensing system detects that the vehicle is in a crash. The sensing system triggers a release of gas from the inflator, which inflates the airbag. The inflator, airbag, and related hardware are all part of the airbag modules inside the steering wheel and in the instrument panel in front of the right front passenger.
What Will You See After an Airbag Inflates? After a frontal airbag inflates, it quickly deflates, so quickly that some people may not even realize the airbag inflated. Roof-mounted side impact airbags may still be at least partially inflated minutes after the vehicle comes to rest.
In many crashes severe enough to inflate an airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system. If you do not get them, the airbag system will not be there to help protect you in another crash. A new system will include airbag modules and possibly other parts.
The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt. The sensors are designed to detect the presence of a properly seated occupant and determine if the passenger’s frontal airbag should be enabled (may inflate) or not. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat.
If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat unless the passenger airbag status indicator shows off and the airbag is off. Here is why: {CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
The passenger sensing system is designed to turn off the right front passenger’s frontal airbag if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a rear-facing infant seat. • The system determines that a small child is present in a forward-facing child restraint. • The system determines that a small child is present in a booster seat. • A right front passenger takes his/her weight off of the seat for a period of time.
The passenger sensing system is designed to enable (may inflate) the right front passenger’s frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger’s seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active.
{CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the frontal airbag. See Airbag Readiness Light on page 183 for more on this, including important safety information.
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. You do not want the system to inflate while someone is working on your vehicle. Your dealer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 482.
Adding Equipment to Your Airbag-Equipped Vehicle Q: Because I have a disability, I have to get Q: Is there anything I might add to the front A: Changing or moving any parts of the or sides of the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Restraint System Check Checking the Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. See Care of Safety Belts on page 427 for more information. Torn or frayed safety belts may not protect you in a crash.
Replacing Restraint System Parts After a Crash {CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
✍ NOTES 96
Section 2 Features and Controls Keys .............................................................. 99 Remote Keyless Entry (RKE) System ........ 101 Remote Keyless Entry (RKE) System Operation .................................. 102 Doors and Locks ........................................ 104 Door Locks ................................................ 104 Power Door Locks ..................................... 105 Programmable Automatic Door Locks ........ 106 Rear Door Security Locks (Crew Cab) .......
Section 2 Features and Controls Mirrors ......................................................... 138 Manual Rearview Mirror ............................. 138 Manual Rearview Mirror with OnStar® ....... 138 Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display .............................. 139 Automatic Dimming Rearview Mirror with Compass and Temperature Display .............................. 142 Outside Manual Mirrors ............................. 145 Outside Power Mirrors ...
Keys {CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
There is a double-sided key that can be used for the ignition, all door locks, and the tailgate. The key code number tells your dealer or a qualified locksmith how to make extra keys. Keep this number in a safe place. If you lose your keys, you will be able to have new ones made easily using this number. Your dealer should also have this number. Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys.
Remote Keyless Entry (RKE) System If the vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
Remote Keyless Entry (RKE) System Operation LOCK: Press this button to lock all the doors. The parking lamps may also flash and the horn may chirp when this button is pressed. If your vehicle has this feature you can lock and unlock your doors and disarm or arm your theft-deterrent system from about 3 feet (1 m) up to 30 feet (9 m) away using the remote keyless entry transmitter. See Content Theft-Deterrent on page 113 for additional information.
Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. When the dealer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched.
Doors and Locks CAUTION: Door Locks • Young children who get into unlocked {CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive.
Power Door Locks If your vehicle has power door locks, the switches are located on the driver’s and the front passenger’s armrests. To lock a door from the inside, push the manual lever on the door forward. To unlock a door from the inside, push the lever on the door rearward. You will see a colored area on the lever when the door is unlocked. Driver’s Switch Shown, Front Passenger’s Switch Similar Press L (lock) to lock all the doors at once. To unlock all the doors, press U (unlock).
Programmable Automatic Door Locks Rear Door Security Locks (Crew Cab) If your vehicle has power door locks and the remote keyless entry system, it has an automatic lock/unlock feature. If your vehicle is a crew cab model, it may have rear door security locks. With this feature, you can lock the rear doors so they cannot be opened from the inside. If your vehicle has an automatic transmission, it is programmed from the factory to lock all doors automatically when the shift lever is moved out of PARK (P).
To engage the security locks, do the following: 1. Open one of the rear doors. 2. Using your ignition key, turn the lock to the horizontal position. 3. Close the door. 4. Repeat these steps on the other rear door. If you want to open a rear door when the security lock is on, unlock the door and open the door from the outside. To disengage the security locks, do the following: 1. Open one of the rear doors. 2. Using your ignition key, turn the lock to the vertical position. 3. Close the door. 4.
Tailgate Removing the Tailgate Follow these steps if you want to remove the tailgate: 1. With the tailgate fully open, lift up slightly on the entire tailgate assembly. 2. Remove the retaining cables from both sides of the tailgate by pulling the clips away from the bolt heads while pushing the cable bracket forward. You can open the tailgate by pulling up on the outside handle while pulling the tailgate down. When you put the tailgate back up, be sure it latches securely.
To partially lower the tailgate do the following: 1. With the tailgate fully open, lift up slightly on the entire tailgate assembly. 2. Remove the retaining cable from the passenger side of the tailgate by pulling the clip away from the bolt head while pushing the cable bracket forward. 3. Slide the lower end fitting onto the top bolt. The tailgate will now stay in the partially opened position. 4. Repeat steps 2 and 3 for the driver side.
Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. Manual Windows On a vehicle with manual windows, use the handle on each door to open and close each window.
Power Windows The power window switches for all windows are located on the driver’s door armrest. In addition, each passenger’s door has its own switch. Crew Cab Switches Shown The power windows will work when the ignition is in ACC (Accessory) or ON or while Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 117. Pull the front of the switch up to raise the window. Press the front of the switch down to lower the window.
Sliding Rear Window Sun Visors To block glare, pull the sun visor down. It can also be detached from the center mount and moved to the side to block glare from that direction. Visor Vanity Mirror The passenger’s side sun visor may have a mirror. Pull down the visor to access the mirror. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal.
Content Theft-Deterrent If your vehicle has the remote keyless entry system, the vehicle has a content theft-deterrent alarm system. To activate the content theft-deterrent system, do the following: 1. Close all the doors. 2. Lock the doors with the remote keyless entry transmitter. The security light, located on the instrument panel cluster, will flash. If the lock button on the remote keyless entry transmitter is pressed, but a door is open, the horn will chirp six times.
Testing the Alarm The alarm can be tested by following these steps: 1. From inside the vehicle, activate the system by locking the doors with the remote keyless entry transmitter. 2. Unlock the door with the manual door lock and open the door. This should set off the alarm. 3. To turn the alarm off, press the unlock button on the remote keyless entry transmitter or start the engine. If the alarm does not sound when it should but the lights flash, check to see if the horn works. The horn fuse may be blown.
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km). • Do not drive at any one constant speed, fast or slow, for the first 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake, or slow, the vehicle. • Avoid making hard stops for the first 200 miles (322 km) or so.
Ignition Positions With the key in the ignition switch, you can turn to four different positions. LOCK (A): This position locks the ignition. It also locks the transmission on automatic transmission vehicles. It will locks the steering wheel on manual transmission vehicles when the key is removed. It is a theft-deterrent feature. You will only be able to remove your key when the ignition is turned to LOCK.
ON (C): This is the position that the switch returns to after you start your engine and release the switch. The switch stays in ON when the engine is running. But even when the engine is not running, you can use ON to operate the electrical accessories and to display some instrument panel cluster warning and indicator lights. The transmission is also unlocked in this position on automatic transmission vehicles. The battery could be drained if you leave the key in the ACC or ON position with the engine off.
Starting the Engine Place the transmission in the proper gear. Automatic Transmission Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position -- this is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving. If you do, you could damage the transmission. Shift to PARK (P) only when your vehicle is stopped.
Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be flooded with too much gasoline.
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located in the engine compartment behind the underhood fuse block on the driver’s side of the vehicle. 3. Plug it into a normal, grounded 110-volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured.
If you need to leave your key in the ignition but not in LOCK for an extended period, it is recommended that you disconnect the battery cable from the battery to prevent discharging your battery. There are several different positions for your shift lever. PARK (P): This position locks your rear wheels. It is the best position to use when you start your engine because your vehicle cannot move easily.
REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice, or sand without damaging your transmission, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 288. NEUTRAL (N): In this position, your engine does not connect with the wheels.
DRIVE (D): This position is for normal driving. If provides the best fuel economy for your vehicle. If you need more power for passing, and you are: • Going less than about 35 mph (55 km/h), push your accelerator pedal about halfway down. • Going about 35 mph (55 km/h) or more, push the accelerator all the way down. You will shift down to the next gear and have more power. SECOND (2): This position reduces vehicle speed even more than THIRD (3) without using your brakes. You can use SECOND (2) on hills.
Manual Transmission Operation This is your shift pattern. SECOND (2): Press the clutch pedal as you let up on the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the accelerator pedal. THIRD, FOURTH AND FIFTH (3, 4 and 5): Shift into THIRD (3), FOURTH (4) and FIFTH (5) the same way you do for SECOND (2). Slowly let up on the clutch pedal as you press the accelerator pedal.
Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. Use REVERSE (R), along with the parking brake, for parking your vehicle. While you accelerate, it is normal for the light to go on and off if you quickly change the position of the accelerator. Ignore the shift light when you downshift.
Four-Wheel Drive If your vehicle has four-wheel drive, you can send your engine’s driving power to all four wheels for extra traction. To get the best performance out of four-wheel drive, you must be familiar with its operation. Read the part that follows before using four-wheel drive. You should use two-wheel-drive high for most normal driving conditions. Notice: Driving on clean, dry pavement in four-wheel drive for an extended period of time can cause premature wear on your vehicle’s powertrain.
Use these buttons to shift into and out of four-wheel drive. You can choose from the following: 2 m (Two-Wheel High): This setting is for driving in most street and highway situations. Your front axle is not engaged in two-wheel drive. {CAUTION: Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P), or if you have a manual transmission, even if you are in gear. You or someone else could be seriously injured.
Shifting from Two-Wheel High to Four-Wheel High Shifting from Two-Wheel High or Four-Wheel High to Four-Wheel Low Press and release the Four-Wheel High button. This can be done at any speed, and the front axle will lock automatically. To shift from Two-Wheel High or Four-Wheel High to Four-Wheel Low, the vehicle must be stopped or moving less than 3 mph (5 km/h) with the transmission in NEUTRAL (N) for an automatic transmission or the clutch pedal pressed for a manual transmission.
Shifting from Four-Wheel Low to Two-Wheel High or Four-Wheel High To shift from Four-Wheel Low to Two-Wheel High or Four-Wheel High, your vehicle must be stopped or moving less than 3 mph (5 km/h) with the transmission in NEUTRAL (N) for an automatic transmission or the clutch pedal engaged for a manual transmission. The preferred method for shifting out of four-wheel low is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the Four-Wheel High or Two-Wheel High button.
7. Turn the engine off by turning the key to ACC (Accessory). 8. Place the transmission shift lever in PARK (P), or FIRST (1) for vehicles that have a manual transmission. 9. Turn the ignition to LOCK. Shifting Out of NEUTRAL After towing your vehicle, you will have to shift out of NEUTRAL in order to drive. To shift out of NEUTRAL, do the following: 1. Set the parking brake and apply the regular brake pedal. 5. After the transfer case has shifted out of NEUTRAL, the indicator light will go out. 6.
A chime will activate and the brake warning light, located on the instrument panel, will flash when the parking brake is applied and the vehicle is moving at least 3 mph (5 km/h) for at least three seconds. The chime will deactivate and the light will turn off when the parking brake is set and the vehicle is moving below 3 mph (5 km/h). See Brake System Warning Light on page 187. If the ignition is on when the parking brake is released, the brake system warning light will go off.
Shifting Into Park (P) (Automatic Transmission) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 305. 1.
Leaving Your Vehicle With the Engine Running (Automatic Transmission) {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Do not leave your vehicle with the engine running.
Shifting Out of Park (P) (Automatic Transmission) Parking Your Vehicle (Manual Transmission) Your vehicle has an automatic transmission shift lock control system which locks the shift lever in PARK (P) when the ignition is in the LOCK position. In addition, you have to fully apply the regular brakes before you can shift from PARK (P) when the ignition is in ON. See Automatic Transmission Operation on page 120. Your vehicle has a manual transmission.
Parking Over Things That Burn {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn.
Engine Exhaust CAUTION: • Your vehicle was damaged when {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different. • Your vehicle gets rusty underneath. • Your vehicle was damaged in a collision. CAUTION: 136 (Continued) (Continued) driving over high points on the road or over road debris. • Repairs were not done correctly.
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 136. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage.
Mirrors {CAUTION: Four-wheel drive vehicles with the transfer case in NEUTRAL will allow the vehicle to roll, even if your automatic transmission shift lever is in PARK (P). So, be sure the transfer case is in a drive gear — not in NEUTRAL. Always set your parking brake. Manual Rearview Mirror While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side.
Cleaning the Mirror Temperature and Compass Display When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror housing. Press the on/off button, located to the far left, briefly to turn the compass/temperature display on or off. Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display Your vehicle may have this feature.
Automatic Dimming Mirror Operation Compass Calibration The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: The compass may need calibration if one of the following occurs: • After approximately five seconds, the display does not show a compass heading, N for North, for example, there may be a strong magnetic field interfering with the compass.
Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, the compass could give false readings.
Cleaning the Mirror Temperature Display When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. The temperature can be displayed by pressing the compass/temperature button. Pressing the compass/temperature button once briefly, will toggle the display reading on and off.
Automatic Dimming Mirror Operation O: Press this button to turn the automatic dimming feature on or off. The indicator light to the left of the button will turn on to indicate when the feature is on. Once the mirror is turned off, it will remain off until it is turned back on, or until the vehicle is restarted. Compass Operation Press the compass/temperature button once briefly to turn the display on or off.
Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is outside zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings.
Cleaning the Mirror Use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Power Mirrors If your vehicle has this feature, the controls are located on the driver’s door armrest. Outside Manual Mirrors If the vehicle has manual outside mirrors, adjust them by hand so that the side of the vehicle can be seen while you are sitting in a comfortable driving position.
If the mirror begins making a ratcheting sound, the mirror has reached the end of its travel and can go no farther in that direction. To stop the sound, reverse the mirror direction using the control pad. The mirrors can be manually folded inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. To return the mirror to its original position, push outward. Be sure to return both mirrors to the unfolded position before driving.
OnStar® System OnStar® uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors.
Available Services with Safe & Sound® Plan • Automatic Notification of Airbag Deployment • Advanced Automatic Crash Notification (AACN) • • • • • • • • (If equipped) Link to Emergency Services Roadside Assistance Stolen Vehicle Location Assistance AccidentAssist Remote Door Unlock/Vehicle Alert OnStar® Vehicle Diagnostics GM® Goodwrench® On Demand Diagnostics OnStar® Hands-Free Calling with 30 complimentary minutes • OnStar® Virtual Advisor Available Services included with Directions & Connections® Plan
OnStar® Steering Wheel Controls Your vehicle may be equipped with a Talk/Mute button that can be used to interact with OnStar® Hands-Free Calling. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” in order to activate the OnStar® Hands-Free Calling feature. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar® Owner’s Guide for more information.
Your vehicle must have a working electrical system (including adequate battery power) for the OnStar® equipment to operate. There are other problems OnStar® cannot control that may prevent OnStar® from providing OnStar® service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion.
Front Armrest Storage Area Assist Handles For vehicles with bench seats, you may have a center armrest storage area. Lift up on the upper tab located at the front of the armrest to release the latch. Lift the lid to open the storage area. Your vehicle may have assist handles to be used when getting out of your vehicle. If your vehicle has assist handles, they are located above the doors. For vehicles with bucket seats or uplevel packages, your vehicle may have a two-tiered center armrest storage area.
To access the storage compartments, lift the cushion on the bottom of the rear seats. This exposes the storage boxes under the seat. 152 To open a storage box, unhook the bottom and lift the two latches on each side of the storage box.
Sunroof Your vehicle may have a sunroof. The sunroof control buttons are located on the headliner. Lift the lid from the center area to access the storage box. Q (Open/Vent): Press and hold this button to vent, and open the sunroof. Release the button when the desired position is reached. R (Close): Press and hold this button to close the sunroof. Release the button when the desired position is reached. The sunshade must be opened manually.
✍ NOTES 154
Section 3 Instrument Panel Instrument Panel Overview ........................ 158 Hazard Warning Flashers .......................... 160 Other Warning Devices ............................. 160 Horn .......................................................... 160 Tilt Wheel .................................................. 161 Turn Signal/Multifunction Lever .................. 161 Turn and Lane-Change Signals ................. 162 Headlamp High/Low-Beam Changer .......... 163 Flash-to-Pass .................
Section 3 Instrument Panel Security Light ............................................ 194 Cruise Control Light .................................. 194 Highbeam On Light ................................... 194 Daytime Running Lamps (DRL) Indicator Light ........................................ 195 Fuel Gage ................................................. 195 Driver Information Center (DIC) .................. 196 DIC Controls and Displays ........................ 196 DIC Warnings and Messages ............
✍ NOTES 157
Instrument Panel Overview Manual Transmission shown, Automatic Transmission similar 158
The main components of your vehicle’s instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 178. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 161. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 180. D. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 160. E. Passenger Side Airbag. See Airbag System on page 76. F. Exterior Lamp Controls. See Exterior Lamps on page 168. Fog Lamps (If Equipped).
Hazard Warning Flashers The hazard warning flashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will flash on and off. The hazard warning flasher button is located on the instrument panel, between the two air vents in the center. Press the button to make the front and rear turn signal lamps flash on and off. Press the button again to turn the flashers off. When the hazard warning flashers are on, the turn signals will not work.
Tilt Wheel Turn Signal/Multifunction Lever A tilt wheel allows you to adjust the steering wheel before you drive. The tilt steering wheel can be raised to the highest level to allow more room for the driver to enter and exit the vehicle. The tilt lever is located on the left side of the steering column, under the turn signal lever. To tilt, hold the steering wheel and pull the tilt lever toward you. Move the wheel to a comfortable level, then release the tilt lever to lock the wheel in place.
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will automatically return to the off position. To signal a lane change, raise or lower the lever until the arrow starts to flash. Hold it there until the change is completed. The lever will return by itself when released.
Headlamp High/Low-Beam Changer 53 (Headlamp High/Low Beam Changer): To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on. Flash-to-Pass This feature lets you use the high-beam headlamps to signal a driver in front of you that you want to pass.
6 (Low Speed): For steady wiping at low speed, turn the band away from you to the first solid position past the delay settings. 1 (High Speed): For high-speed wiping, turn the band to the second solid position past the delay settings. 9 (Off): To stop the wipers, move the band to off. QL (Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer fluid on the windshield, push the paddle.
+ (Resume/Accelerate): Move the lever to this position to make the vehicle accelerate or resume to a previously set speed. rT (Set): Press this button to set the speed. With cruise control, the vehicle can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h).
Setting Cruise Control Resuming a Set Speed Suppose you set the cruise control to a desired speed and then you apply the brake. This turns off the cruise control. But it does not need to be reset. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1.
Increasing Speed While Using Cruise Control Passing Another Vehicle While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal. You will now cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. • Move the cruise lever from on to resume/accelerate.
Ending Cruise Control Exterior Lamps To turn off the cruise control, do one of the following: • Step lightly on the brake pedal. • Move the cruise control lever to off. • Lightly tap or press the clutch, if you have a manual transmission. Erasing Speed Memory When you turn off the cruise control or the ignition, the cruise control set speed memory is erased. The control on the driver’s side of the instrument panel operates the exterior lamps.
O (Exterior Lamps): Turn the knob, located to the right of this symbol, to choose one of the four exterior lamp positions. 2 (Headlamps): Turn the knob to this position to turn on the headlamps, together with the previously listed lamps and lights. 9 (Off): Turn the knob to this position to turn off You can switch the headlamps from low to high beam by pushing the turn signal/multifunction lever toward the instrument panel. all exterior lamps including the Daytime Running Lamps (DRL).
Daytime Running Lamps (DRL) Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system will come on when the following conditions are met: • The ignition is on.
There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp system so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor detects a change in lighting lasting longer than the delay. If you start your vehicle in a dark garage, the automatic headlamp system will come on immediately.
Exterior Cargo Lamps Interior Lamps The cargo lamps can be used if more light is needed in the cargo area of the vehicle or in the top-box storage units. The thumbwheel for the interior lamps is located next to the exterior lamps control. See Exterior Lamps on page 168 for additional information on location. Press this button, located on the driver side of the instrument panel near the exterior lamp control, to turn the cargo lamps on and off. The dome lamps must be on for the cargo lamps to come on.
Dome Lamp Exit Lighting The dome lamp will come on when a door is opened. They will shut off several seconds after all doors are closed. With exit lighting, the interior lamps will come on when you remove the key from the ignition. The lamps will not come on if the dome override button is pressed in. You can also turn the dome lamp on manually by turning the interior lamps thumbwheel all the way up. In this position, the dome lamp will remain on whether a door is opened or closed.
The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads.
Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer before adding electrical equipment. Ashtray(s) and Cigarette Lighter When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment.
Climate Controls Climate Control System Fan Knob 9 (Fan): The center knob on the control panel is used to control the fan speed. Turn the knob clockwise or counterclockwise to increase or decrease the fan speed. If the knob is set on “0” (zero), some outside air will still enter the vehicle and will be directed according to the position of the mode knob. Mode Knob The right knob on the control panel is used to direct the airflow inside your vehicle.
[ (Floor): Select this mode to direct air to the floor outlets. Recirculation is disabled in this mode because interior window could fog under some conditions. If this occurs, see “Defogging and Defrosting” following. Mode Buttons @ (Recirculation): This mode recirculates air inside the cabin, and prevents outside air from coming in the vehicle. It can be used to prevent outside odors from entering your vehicle and cool the air inside your vehicle more quickly.
Turn the mode knob on the climate control panel clockwise to select the defog or defrost modes. Outlet Adjustment / (Floor/Defog): This mode directs the air to the Use the thumbwheel on the outlets to change the direction of the air flow. windshield, the side window outlets, and to the floor outlets. When you select this mode, the system runs the air conditioning compressor unless the outside temperature is near freezing or below. Recirculation is not available in this mode.
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions.
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
Speedometer and Odometer Trip Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your vehicle has a trip odometer that can tell you how far your vehicle has been driven since you last set the trip odometer to zero. Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). See “Trip Odometer” under DIC Controls and Displays on page 196 for more information.
Safety Belt Reminder Light When the key is turned to ON or START, a chime will be provided for several seconds to remind people to buckle their safety belts. The driver safety belt light will also be provided and stay on for several seconds, then it will flash for several more. You should buckle your seat belt. Passenger Safety Belt Reminder Light This chime and light will be repeated if the driver remains unbuckled and the vehicle is in motion.
Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag systems, see Airbag System on page 76.
Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your instrument panel has a passenger airbag status indicator. There is a label on your sun visor that says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great if the airbag deploys.
If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat unless the passenger airbag status indicator shows off and the airbag is off.
If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag. See Passenger Sensing System on page 86 for more on this, including important safety information. If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.
Up-Shift Light (Manual Transmission) If the warning light comes on, there could be a brake problem. Have your brake system inspected right away. This light appears when you need to shift to the next higher gear on a manual transmission vehicle. United States Shifting when the indicator light is on will help you get the best fuel economy. See “Up-Shift Light” under Manual Transmission Operation on page 124 for more information.
If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push, or the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 297. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident.
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the gage pointer is near the top of the gage, the engine is too hot. It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible. See Engine Overheating on page 348 for more information.
Malfunction Indicator Lamp Check Engine Light Your vehicle has a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is a problem and service is required.
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: • Light Flashing — A misfire condition has been detected. A misfire increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required.
Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 325. Poor fuel quality will cause your engine not to run as efficiently as designed.
Oil Pressure Light The light will come on when you turn your key to ON or START. {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil.
Security Light Cruise Control Light This light will come on briefly when you turn the key to START. The light will stay on until the engine starts. If the ignition is turned on, and the light flashes, the Passlock® system has entered a tamper mode. If the vehicle fails to start, see Passlock® on page 114. If the light comes on continuously while driving and stays on, there may be a problem with the Passlock® system. Your vehicle will not be protected by Passlock®, and you should see your dealer.
Daytime Running Lamps (DRL) Indicator Light This light turns on whenever the Daytime Running Lamps are on. See Daytime Running Lamps (DRL) on page 170 for more information. Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have remaining in the fuel tank. Here are four things that some owners ask about. None of these indicate a problem with your fuel gage: • At the gas station, the gas pump shuts off before the gage reads full.
Driver Information Center (DIC) The Driver Information Center (DIC) displays information such as the trip odometer, personalization features, and warning messages. The DIC display is located on the instrument panel cluster. Trip Information Odometer The odometer is automatically displayed on the DIC when you start the vehicle. The odometer shows the total distance the vehicle has been driven in either miles for the United States or kilometers for Canada.
Engine Oil Life System Language With the engine off, turn the key to ON and then press the reset stem until OIL LIFE RESET appears — alternating between OIL LIFE and RESET — on the DIC display. The CHANGE OIL message will alert you to change your oil on a schedule consistent with your driving conditions. Always reset the OIL LIFE message after an oil change. To reset the message, see Engine Oil Life System on page 336.
Automatic Door Locks This feature allows you to program your door locks to a preferred setting. To set your choice for this feature, perform the following steps: 1. With the engine off, turn the key to LOCK. Do not remove the key from the ignition. 2. Press and hold the power door lock button for about three seconds until the DIC display shows the current door lock mode. 3. To view the next available mode, press and hold the reset stem for about two seconds.
Remote Keyless Entry (RKE) Feedback The following are the available modes: This feature allows you to program your Remote Keyless Entry (RKE) feedback to a preferred setting. RFA 1 (default): This mode flashes the parking lamps when you press the lock or unlock buttons on the RKE transmitter. To set your choice for this feature, perform the following steps: 1. With the engine off, turn the key to LOCK. Do not remove the key from the ignition. 2.
DIC Warnings and Messages AC (Air Conditioning) OFF Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. The messages are displayed for four seconds each. This message displays when the engine coolant temperature is too high and the air conditioning in your vehicle needs to be turned off.
BRAKES ENG (Engine) HOT This message displays if there is a problem with the brakes. Check the brakes as soon as possible and have your vehicle serviced by your dealer. See Brakes on page 357 and Brake System Warning Light on page 187 for more information. Press and release the reset stem to acknowledge the message and clear it from the display. This message displays when the engine coolant temperature is hot. Check the engine coolant temperature gage. See Engine Coolant Temperature Gage on page 189.
FUEL CAP LOW TIRE This message displays if the vehicle’s fuel cap is either off or loose. Pull over as soon as possible and check to see if the fuel cap is secure. You may also see the check engine light on the instrument panel cluster. If the check engine light does come on when the fuel cap was loose, it may take a few driving trips before the light turns off. See Malfunction Indicator Lamp on page 190 for more information if the light still remains on.
PARK BRK (Brake) This message displays when the parking brake is set. See Parking Brake on page 130 and Brake System Warning Light on page 187 for more information. The message clears from the display after the parking brake is released or by pressing and releasing the reset stem. REDUCED POWER This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate.
SERV (Service) VEH (Vehicle) TRACTION FAULT This message displays if your vehicle needs service. Have your vehicle serviced by your dealer as soon as possible. If your vehicle has the Traction Control System (TCS), this message may display if there is a problem with the TCS. Check the TCS as soon as possible and have your vehicle serviced by your dealer. See Traction Control System (TCS) on page 253 for more information.
Audio System(s) Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features. Driving without distraction is a necessity for a safer driving experience. See Defensive Driving on page 246. By taking a few moments to read this manual and get familiar with your vehicle’s audio system, you can use it with less effort, as well as take advantage of its features.
Here are some ways in which you can help avoid distraction while driving. While your vehicle is parked: • Familiarize yourself with all of its controls. • Familiarize yourself with its operation. • Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers. Then, when driving conditions permit, you can tune to your favorite radio stations using the presets and steering wheel controls if the vehicle has them.
Setting the Time for Radios with Radio Data Systems (RDS) AM-FM Radio The radio may have a button marked with an H or HR to represent hours and an M or MN to represent minutes. Press and hold the hour button until the correct hour appears on the display. Press and hold the minute button until the correct minute appears on the display. The time can be set with the ignition on or off.
Finding a Station Setting Preset Stations AM FM: Press this button to switch between FM1, FM2, or AM. The selection displays. Up to 18 stations (six FM1, six FM2, and six AM) can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. TUNE: Turn this knob to select radio stations. o SEEK p: Press the right or the left arrow to go to the next or to the previous station and stay there.
Setting the Tone (Bass/Treble) Adjusting the Speakers (Balance/Fade) AUDIO: To adjust bass or treble, press and release AUDIO until BAS (bass) or TRE (treble) displays. Then press and hold the up or the down arrow to increase or to decrease the tone. If a station is weak or has static, decrease the treble. AUDIO: To adjust the balance between the right and the left speakers, press and release AUDIO until BAL (balance) displays.
Radio Messages Radio with CD (MP3) CAL (Calibrated): The audio system has been calibrated for your vehicle from the factory. If CAL displays it means that the radio has not been configured properly for your vehicle and must be returned to your dealer for service. LOC (Locked): This message is displayed when the THEFTLOCK® system has locked up. Take the vehicle to your dealer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer.
With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming • Receive announcements concerning local and national emergencies • Display messages from radio stations • Seek to stations with traffic announcements This system relies upon receiving specific information from these stations and only works when the information is available. In rare cases, a radio station may broadcast incorrect information that causes the radio features to work improperly.
Playing the Radio PWR (Power): Press this knob to turn the system on and off. o VOL p (Volume): Turn this knob to increase or to decrease the volume. DISPL (Display): When the ignition is turned off, press this knob to display the time. For RDS, press the DISPL knob to change what appears on the display while using RDS. The display options are station name, RDS station frequency, PTY (program type), and the name of the program (if available).
q SEEK r: Press the right or the left arrow to go to the next or to the previous station and stay there. The radio only seeks stations with a strong signal that are in the selected band. q SCAN r: Press and hold either arrow for more than two seconds. SCAN appears on the display and the radio produces one beep. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again or one of the pushbuttons to stop scanning presets.
Setting the Tone (Bass/Treble) Adjusting the Speakers (Balance/Fade) AUDIO: Push and release the AUDIO knob until BASS or TREB appears on the display. Turn the knob to increase or to decrease. The tone display shows the bass or the treble level. If a station is weak or has static, decrease the treble. AUDIO: To adjust the balance between the right and the left speakers, push and release the AUDIO knob until BAL (balance) appears on the display.
Finding a Program Type (PTY) Station (RDS and XM™) To select and find a desired PTY perform the following: 1. Turn the P-TYPE knob to activate program type select mode. TYPE and a PTY appears on the display. 2. Turn the P-TYPE knob again, to select a PTY. 3. Once the desired PTY displays, press the SEEK TYPE button to select and to take you to the PTY’s first station. 4. To go to another station within that PTY, press the SEEK TYPE button twice to display the PTY and then go to another station. 5.
RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! appears on the display. You will hear the announcement, even if the volume is low or a CD is playing. If a CD is playing, play stops during the announcement. Alert announcements cannot be turned off. ALERT! is not affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations.
TRAF (Traffic): If TRAF appears on the display, the tuned station broadcasts traffic announcements. When a traffic announcement is broadcast on this station you will hear it. Radio Messages CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If CAL ERR appears on the display it means that the radio has not been configured properly for your vehicle and it must be returned to your dealer for service.
Playing a CD Insert a CD partway into the slot, label side up. The player pulls it in, and READING appears on the display. The CD should begin playing. If you want to insert a CD with the ignition off, first press the eject button or the DISPL knob. If the ignition or radio is turned off with a CD in the player it stays in the player. When the ignition or radio is turned on, the CD starts to play where it stopped, if it was the last selected audio source.
1 FLD x (Previous): This button is inactive when playing a CD. 2 FLD w (Next): This button is inactive when playing a CD. 3 REV (Reverse): Press and hold this pushbutton to reverse quickly within a track. Press and hold this pushbutton for less than two seconds to reverse at 10 times the normal playing speed. Press and hold it for more than two seconds to reverse at 20 times the normal playing speed. Release this pushbutton to play the passage.
BAND: Press this button to listen to the radio when a CD is playing. The inactive CD remains safely inside the radio for future listening. CD AUX (Auxiliary): Press this button to play a CD when listening to the radio. The CD symbol appears on the display when a CD is loaded. Z (Eject): Press this button to eject a CD. Eject may be activated with either the ignition or radio off. CDs may be loaded with the ignition and radio off if this button is pressed first.
Radio with Six-Disc CD With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming • Receive announcements concerning local and national emergencies • Display messages from radio stations • Seek to stations with traffic announcements This system relies upon receiving specific information from these stations and only works when the information is available.
XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous United States and Canada. XM™ offers a large variety of coast-to-coast channels including music, news, sports, talk, traffic/weather (U.S. subscribers), and children’s programming. XM™ provides digital quality audio and text information that includes song title and artist name. A service fee is required in order to receive the XM™ service. For more information, contact XM™; In the U.S. at www.xmradio.
AUTO VOL (Automatic Volume): With automatic volume, the audio system adjusts automatically to make up for road and wind noise as you drive by increasing the volume as vehicle speed increases. Set the volume at the desired level. Press this button to select MIN (minimum), MED (medium), or MAX. AUTO VOL (maximum automatic volume) appears on the display. Each higher setting provides more volume compensation at faster vehicle speeds.
Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped)), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2 (if equipped). 3. Tune in the desired station. 4. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the station that was set returns for that pushbutton. 5.
Setting the Tone (Bass/Midrange/Treble) AUDIO: Push and release the AUDIO knob until BASS, MID, or TREB appears on the display. Turn the knob to increase or to decrease. The display shows the bass, midrange, or treble level. If a station is weak or has static, decrease the treble. To adjust the bass, midrange, and treble to the middle position, push and hold the AUDIO knob. The radio produces one beep and adjusts the display level to the middle position.
Finding a Program Type (PTY) Station (RDS and XM™) To select and find a desired PTY perform the following: 1. Press the TYPE button to activate program type select mode. P-TYPE and the last selected PTY appears on the display. 2. Turn the TYPE knob or press and release the TYPE button to select a PTY. 3. Once the desired PTY is displayed, press either the TYPE or the SEEK arrows to select and to take you to the PTY’s first station. 4. To cancel the seek, press any of the TYPE or SEEK arrows.
Setting Preset PTYs (RDS Only) RDS Messages These pushbuttons have factory PTY presets. Up to 12 PTYs (six FM1 and six FM2), can be programmed on the six numbered pushbuttons, by performing the following steps: INFO (Information): If the current station has a message, INFO appears on the display. Press this button to see the message. The message may display the artist, song title, call in phone numbers, etc. 1. Press BAND to select FM1 or FM2. 2.
Radio Messages CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If CAL ERR appears on the display, it means that the radio has not been configured properly for the vehicle and must be returned to your dealer for service. LOCKED: This message is displayed when the THEFTLOCK® system has locked up. Take the vehicle to your dealer for service. If any error occurs repeatedly, or if an error cannot be corrected, contact your dealer.
Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen. Notice: If you add any label to a CD, insert more than one CD into the slot at a time, or attempt to play scratched or damaged CDs, you could damage the CD player.
Playing a Specific Loaded CD For every CD loaded, a number appears on the display. To play a specific CD, first press the CD AUX button (if not already in CD mode), then press the numbered pushbutton that corresponds to the CD. A small bar appears under the CD number that is playing and the track number appears on the display. If an error appears on the display, see “CD Messages” later in this section. CD Z (Eject): Press this button to eject CD(s).
RPT (Repeat): With repeat, one track or an entire CD can be repeated. To use repeat, do the following: • To repeat the track you are listening to, press and release the RPT button. RPT appears on the display. Press RPT again to turn off repeat play. • To repeat the CD you are listening to, press and hold the RPT button for two seconds. RPT appears on the display. Press RPT again to turn off repeat play.
INFO (Information): Press this knob to see how long the current track has been playing. To change the default on the display, track or elapsed time, press the knob until you see the desired display, then press and hold the knob until the radio beeps. The selected display becomes the default. BAND: Press this button to listen to the radio while a CD is playing. The inactive CD(s) remains safely inside the radio for future listening.
To delete tracks from the song list, perform the following steps: 1. Turn the CD player on. 2. Press the SONG LIST button to turn song list on. S-LIST appears on the display. 3. Press either SEEK or TYPE arrow to select the desired track to be deleted. 4. Press and hold the SONG LIST button for two seconds. When SONG LIST is pressed, one beep will sound. After two seconds of continuously pressing the SONG LIST button, two beeps will sound to confirm that the track has been deleted.
CD Messages Using an MP3 CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play. • The CD is dirty, scratched, wet, or upside down. • The air is very humid. If so, wait about an hour and try again. • There may have been a problem while burning the CD.
The player is able to read and play a maximum of 50 folders, 50 playlists, 10 sessions, and 255 files. Long file names, folder names, or playlist names may use more disc memory space than necessary. To conserve space on the disc, minimize the length of the file, folder, or playlist names. You can also play an MP3 CD that was recorded using no file folders.
Order of Play File System and Naming Tracks are played in the following order: • Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the first track of the first playlist. • If the CD does not contain any playlists, then play begins from the first track under the root directory.
If the ignition or radio is turned off with a CD in the player it stays in the player. When the ignition or radio is turned on, the CD starts to play where it stopped, if it was the last selected audio source. As each new track starts to play, the track number appears on the display. The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring. Full-size CDs and the smaller CDs are loaded in the same manner.
3 REV (Reverse): Press and hold this pushbutton to reverse quickly within a track. Press and hold this pushbutton for less than two seconds to reverse at 10 times the normal playing speed. Press and hold it for more than two seconds to reverse at 20 times the normal playing speed. Release this pushbutton to play the passage. REV and the elapsed time of the track appears on the display. 4 FWD (Forward): Press and hold this pushbutton to advance quickly within a track.
DISPL (Display): Press this knob to switch between track mode, folder/playlist mode, and time of day mode. The display shows only eight characters, but there can be up to four pages of text. If there are more than eight characters in the song, folder, or playlist name, pressing this knob within two seconds takes you to the next page of text. If there are no other pages to be shown, pressing this knob within two seconds takes you to the next display mode.
XM Radio Messages Radio Display Message Condition Action Required XL (Explicit Language Channels) XL on the radio display, after the channel name, indicates content with explicit language. Updating Updating encryption code The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No Signl Loss of signal The system is functioning correctly, but the vehicle is in a location that is blocking the XM™ signal.
Radio Display Message Condition Action Required No Info Category Name not available No category information is available at this time on this channel. The system is working properly. No Info No Text/Informational message available No text or informational messages are available at this time on this channel. The system is working properly. NotFound No channel available for the chosen category There are no channels available for the selected category. The system is working properly.
Theft-Deterrent Feature (Non-RDS Radios) THEFTLOCK® is designed to discourage theft of your vehicle’s radio. The feature works automatically by learning a portion of the Vehicle Identification Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOC will appear on the display. With THEFTLOCK® activated, the radio will not operate if stolen. Theft-Deterrent Feature (RDS Radios) THEFTLOCK® is designed to discourage theft of your vehicle’s radio.
FM Stereo Care of Your CDs FM stereo will give the best sound, but FM signals will reach only about 10 to 40 miles (16 to 65 km). Tall buildings or hills can interfere with FM signals, causing the sound to fade in and out. Handle CDs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom surface of the disc.
Fixed Mast Antenna Chime Level Adjustment The fixed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, straighten it out by hand. If the mast is badly bent, replace it. The radio is used to adjust the vehicle’s chime level. To change the volume level of the chime, press and hold pushbutton 6 with the ignition on and the radio power off. The volume level will change from the normal level to loud, and LOUD will appear on the radio display.
Section 4 Driving Your Vehicle Your Driving, the Road, and Your Vehicle .... 246 Defensive Driving ...................................... 246 Drunken Driving ........................................ 247 Control of a Vehicle .................................. 250 Braking ...................................................... 250 Anti-Lock Brake System (ABS) .................. 251 Braking in Emergencies ............................. 253 Traction Control System (TCS) ..................
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 20. 246 {CAUTION: Defensive driving really means “Be ready for anything.” On city streets, rural roads, or expressways, it means “Always expect the unexpected.” Assume that pedestrians or other drivers are going to be careless and make mistakes.
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: • Judgment • Muscular Coordination • Vision • Attentiveness Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving.
According to the American Medical Association, a 180 lb (82 kg) person who drinks three 12 ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4 ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of liquors like whiskey, gin, or vodka. It is the amount of alcohol that counts.
But the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent. Statistics show that the chance of being in a collision increases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of 0.06 percent has doubled his or her chance of having a collision.
Control of a Vehicle Braking You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering, and the accelerator. All three systems have to do their work at the places where the tires meet the road. Braking action involves perception time and reaction time. Sometimes, as when you are driving on snow or ice, it is easy to ask more of those control systems than the tires and road can provide. That means you can lose control of your vehicle.
Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake. The brakes may not have time to cool between hard stops. The brakes will wear out much faster if you do a lot of heavy braking. If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life.
ABS can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down.
Remember: ABS does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even though you have ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let anti-lock work for you.
If your vehicle is in cruise control when the traction control system begins to limit wheel spin, the cruise control will automatically disengage. When road conditions allow you to safely use it again, you may re-engage the cruise control. See Cruise Control on page 164. TCS operates in all transmission shift lever positions. But the system can upshift the transmission only as high as the shift lever position you have chosen, so you should use the lower gears only when necessary.
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips It is important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here is why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. You can avoid these problems by braking — if you can stop in time. But sometimes you cannot; there is not room. That is the time for evasive action — steering around the problem.
Off-Road Recovery Passing You may find that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again.
• Watch for traffic signs, pavement markings, and lines. If you can see a sign up ahead that might indicate a turn or an intersection, delay your pass. A broken center line usually indicates it is all right to pass, providing the road ahead is clear. Never cross a solid line on your side of the lane or a double solid line, even if the road seems empty of approaching traffic. • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity.
Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up. Keep trying to steer and constantly seek an escape route or area of less danger. Skidding In a skid, a driver can lose control of the vehicle.
Off-Road Driving Before You Go Off-Roading This off-road guide is for vehicles that have four-wheel drive. Also, see Braking on page 250 and Anti-Lock Brake System (ABS) on page 251. If your vehicle does not have four-wheel drive, you should not drive off-road unless you are on a level, solid surface. There are some things to do before you go out. For example, be sure to have all necessary maintenance and service work done.
Loading Your Vehicle for Off-Road Driving {CAUTION: • Cargo on the load floor piled higher than the seatbacks can be thrown forward during a sudden stop. You or your passengers could be injured. Keep cargo below the top of the seatbacks. • Unsecured cargo on the load floor can be tossed about when driving over rough terrain. You or your passengers can be struck by flying objects. Secure the cargo properly. • Heavy loads on the roof raise the vehicle’s center of gravity, making it more likely to roll over.
Environmental Concerns Traveling to Remote Areas Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: • Always use established trails, roads, and areas that have been specially set aside for public off-road recreational driving; obey all posted regulations.
Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: • You approach things faster and you have less time to scan the terrain for obstacles. • You have less time to react. • You have more vehicle bounce when you drive over obstacles. • You will need more distance for braking, especially since you are on an unpaved surface.
Surface Obstacles: Unseen or hidden obstacles can be hazardous. A rock, log, hole, rut, or bump can startle you if you are not prepared for them. Often these obstacles are hidden by grass, bushes, snow, or even the rise and fall of the terrain itself. Here are some things to consider: • Is the path ahead clear? • Will the surface texture change abruptly up ahead? • Does the travel take you uphill or downhill? There is more discussion of these subjects later.
Driving on Off-Road Hills Off-road driving often takes you up, down, or across a hill. Driving safely on hills requires good judgment and an understanding of what your vehicle can and cannot do. There are some hills that simply cannot be driven, no matter how well built the vehicle. {CAUTION: Many hills are simply too steep for any vehicle. If you drive up them, you will stall. If you drive down them, you cannot control your speed. If you drive across them, you will roll over.
Driving Uphill Once you decide you can safely drive up the hill, you need to take some special steps. • Use a low gear and get a firm grip on the steering wheel. • Get a smooth start up the hill and try to maintain your speed. Do not use more power than you need, because you do not want your wheels to start spinning or sliding. • Try to drive straight up the hill if at all possible. If the path twists and turns, you might want to find another route.
Q: What should I do if my vehicle stalls, or is about to stall, and I cannot make it up the hill? A: If this happens, there are some things you should do, and there are some things you must not do. First, here is what you should do: • Push the brake pedal to stop the vehicle and keep it from rolling backwards. Also, apply the parking brake. • If your engine is still running, shift the transmission to REVERSE (R), release the parking brake, and slowly back down the hill in REVERSE (R).
Q: Suppose, after stalling, I try to back down the hill and decide I just cannot do it. What should I do? A: Set the parking brake, put the automatic transmission in PARK (P), or the manual transmission in FIRST (1), and turn off the engine. Leave the vehicle and go get some help. Exit on the uphill side and stay clear of the path the vehicle would take if it rolled downhill.
Q: Are there some things I should not do when driving down a hill? A: Yes! These are important because if you ignore them you could lose control and have a serious accident. • When driving downhill, avoid turns that take you across the incline of the hill. A hill that is not too steep to drive down may be too steep to drive across. You could roll over if you do not drive straight down.
Driving Across an Incline Sooner or later, an off-road trail will probably go across the incline of a hill. If this happens, you have to decide whether to try to drive across the incline. Here are some things to consider: • A hill that can be driven straight up or down may be too steep to drive across. When you go straight up or down a hill, the length of the wheel base — the distance from the front wheels to the rear wheels — reduces the likelihood the vehicle will tumble end over end.
Q: What if I am driving across an incline that is not too steep, but I hit some loose gravel and start to slide downhill. What should I do? A: If you feel your vehicle starting to slide sideways, turn downhill. This should help straighten out the vehicle and prevent the side slipping. However, a much better way to prevent this is to get out and “walk the course” so you know what the surface is like before you drive it.
Driving in Mud, Sand, Snow, or Ice When you drive in mud, snow, or sand, your wheels will not get good traction. You cannot accelerate as quickly, turning is more difficult, and you will need longer braking distances. It is best to use a low gear when you are in mud — the deeper the mud, the lower the gear. In really deep mud, the idea is to keep your vehicle moving so you do not get stuck. When you drive on sand, you will sense a change in wheel traction.
If the water is not too deep, drive slowly through it. At faster speeds, water splashes on the ignition system and your vehicle can stall. Stalling can also occur if you get the tailpipe under water. And, as long as the tailpipe is under water, you will never be able to start the engine. When you go through water, remember that when the brakes get wet, it may take you longer to stop. {CAUTION: Driving through rushing water can be dangerous.
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Adjust the inside rearview mirror to reduce the glare from headlamps behind you. • Since you cannot see as well, you may need to slow down and keep more space between you and other vehicles.
Keep the windshield and all the glass on your vehicle clean — inside and out. Glare at night is made much worse by dirt on the glass. Even the inside of the glass can build up a film caused by dust. Dirty glass makes lights dazzle and flash more than clean glass would, making the pupils of your eyes contract repeatedly. Driving in Rain and on Wet Roads Remember that the headlamps light up far less of a roadway when you are in a turn or curve.
The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking. Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you cannot, try to slow down before you hit them.
Driving Through Deep Standing Water Notice: If you drive too quickly through deep puddles or standing water, water can come in through your engine’s air intake and badly damage your engine. Never drive through water that is slightly lower than the underbody of your vehicle. If you cannot avoid deep puddles or standing water, drive through them very slowly.
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. 278 Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip. • Try to use the freeways that rim and crisscross most large cities.
Freeway Driving The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-fast or too-slow driving breaks a smooth traffic flow. Treat the left lane on a freeway as a passing lane. At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic.
Before changing lanes, check your mirrors. Then use your turn signal. Just before you leave the lane, glance quickly over your shoulder to make sure there is not another vehicle in your blind spot. Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night. When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit.
Here are some things you can check before a trip: • Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside? • Wiper Blades: Are they in good shape? • Fuel, Engine Oil, Other Fluids: Have you checked all levels? • Lamps: Are they all working? Are the lenses clean? • Tires: They are vitally important to a safe, trouble-free trip.
Hill and Mountain Roads If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. See Off-Road Driving on page 260 for information about driving off-road. • Keep your vehicle in good shape. Check all fluid levels and also the brakes, tires, cooling system, and transmission. These parts can work hard on mountain roads.
• Stay in your own lane when driving on two-lane {CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Always have your engine running and your vehicle in gear when you go downhill. roads in hills or mountains. Do not swing wide or cut across the center of the road.
Winter Driving Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, a red cloth, and a couple of reflective warning triangles. And, if you will be driving under severe conditions, include a small bag of sand, a piece of old carpet, or a couple of burlap bags to help provide traction. Be sure you properly secure these items in your vehicle.
Accelerate gently. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more. What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing, 32°F (0°C), and freezing rain begins to fall.
If You Are Caught in a Blizzard If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: • Turn on your hazard flashers. • Tie a red cloth to your vehicle to alert police that you have been stopped by the snow. • Put on extra clothing or wrap a blanket around you.
{CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking your exhaust pipe. And check around again from time to time to be sure snow does not collect there. Run your engine only as long as you must. This saves fuel.
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you do not want to spin your wheels too fast. The method known as rocking can help you get out when you are stuck, but you must use caution. Notice: Spinning the wheels can destroy parts of your vehicle as well as the tires. If you spin the wheels too fast while shifting the transmission back and forth, you can destroy the transmission.
By slowly spinning the wheels in the forward and reverse directions, you will cause a rocking motion that may free your vehicle. If that does not get your vehicle out after a few tries, it may need to be towed out.Or, you can use the recovery hooks if your vehicle has them. If your vehicle does need to be towed out, see Towing Your Vehicle on page 297. Recovery Hooks {CAUTION: These hooks, when used, are under a lot of force. Always pull the vehicle straight out.
Loading Your Vehicle Tire and Loading Information Label It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certification/Tire label.
The Tire and Loading Information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds. The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inflation pressures (D). For more information on tires and inflation see Tires on page 377 and Inflation - Tire Pressure on page 385. There is also important information on the Certification/Tire label.
Example 1 Item A B C 292 Description Total Vehicle Capacity 1,000 lbs (453 kg) Weight for Example 1 = Subtract Occupant Weight 300 lbs (136 kg) 150 lbs (68 kg) x 2 = Available Cargo Weight = 700 lbs (317 kg) Example 2 Item A B C Description Total Vehicle Capacity 1,000 lbs (453 kg) Weight for Example 2 = Subtract Occupant Weight 750 lbs (340 kg) 150 lbs (68 kg) x 5 = Available Cargo Weight = 250 lbs (113 kg)
Certification/Tire Label Example 3 Item A B C Description Total Vehicle Capacity 1,000 lbs (453 kg) Weight for Example 3 = Subtract Occupant Weight 1,000 lbs (453 kg) 200 lbs (91 kg) x 5 = Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle’s Tire and Loading Information label for specific information about your vehicle’s capacity weight and seating positions.
The GVWR includes the weight of the vehicle, all occupants, fuel, cargo, and trailer tongue weight, if pulling a trailer. The Certification/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline.
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. {CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash. • Put things in the cargo area of your vehicle. Try to spread the weight evenly.
Add-On Equipment Truck-Camper Loading Information When you carry removable items, you may need to put a limit on how many people you carry inside your vehicle. Be sure to weigh your vehicle before you buy and install the new equipment. Your vehicle was not designed to carry a slide-in camper. Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle. Remember not to exceed the Gross Axle Weight Rating (GAWR) of the rear axle.
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 470. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing” following. Recreational Vehicle Towing Recreational vehicle towing means towing your vehicle behind another vehicle — such as behind a motorhome.
Dinghy Towing Four-Wheel Drive Vehicles Two-Wheel Drive Vehicles Notice: If you tow your vehicle with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by your warranty. Do not tow your vehicle with all four wheels on the ground. Two-wheel-drive vehicles should not be towed with all four wheels on the ground. Two-wheel-drive transmissions have no provisions for internal lubrication while being towed.
3. Put an automatic transmission in PARK (P) or a manual transmission in FIRST (1). 4. Securely attach the vehicle being towed to the tow vehicle. {CAUTION: Shifting a four-wheel-drive vehicle’s transfer case into NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P) for an automatic transmission, or if your vehicle is in gear, for a manual transmission. You or others could be injured. Make sure the parking brake is firmly set before you shift the transfer case to NEUTRAL. 5.
Dolly Towing Four-Wheel-Drive Vehicles Front Towing (Front Wheels Off the Ground) Two-Wheel-Drive Vehicles Notice: If you tow a two-wheel-drive vehicle with the rear wheels on the ground, the transmission could be damaged. The repairs would not be covered by your warranty. Never tow your vehicle with the rear wheels on the ground. Two-wheel-drive vehicles should not be towed with the rear wheels on the ground. Two-wheel-drive transmissions have no provisions for internal lubrication while being towed.
3. Put an automatic transmission in PARK (P) or a manual transmission in FIRST (1). 4. Follow the dolly manufacturer’s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle. {CAUTION: Shifting a four-wheel-drive vehicle’s transfer case into NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P) for an automatic transmission, or if your vehicle is in gear, for a manual transmission. You or others could be injured.
Rear Towing (Rear Wheels Off the Ground) Two-Wheel-Drive Vehicles Use the following procedure to tow your vehicle from the rear: 1. Drive the vehicle onto the dolly. 2. Firmly set the parking brake. See Parking Brake on page 130 for more information. 302 3. Put an automatic transmission in PARK (P) or a manual transmission in FIRST (1). 4. Follow the dolly manufacturer’s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle.
5. Release the parking brake only after the vehicle being towed is firmly attached to the tow vehicle. 6. Turn the ignition to LOCK. If the tow vehicle will not be started or driven for six weeks or more, remove the battery cable from the negative terminal (post) of the battery to prevent your battery from draining while towing. Four-Wheel-Drive Vehicles Use the following procedure to tow your vehicle from the rear: 1. Drive the vehicle onto the dolly. 2. Firmly set the parking brake.
4. Follow the dolly manufacturer’s instructions to attach and secure the vehicle being towed to the dolly and then the loaded dolly to the tow vehicle. For manual transmission vehicles, make sure the wheels are straight before proceeding to the next steps. On automatic transmission vehicles, use an adequate clamping device to ensure that the front wheels are locked into the straight position.
Towing a Trailer {CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured. Pull a trailer only if you have followed all the steps in this section. Ask your dealer for advice and information about towing a trailer with your vehicle.
If You Do Decide To Pull A Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving. A good source for this information can be state or provincial police. • Consider using a sway control. You can ask a hitch dealer about sway controls. • Don’t tow a trailer at all during the first 500 miles (800 km) your new vehicle is driven.
Weight of the Trailer How heavy can a trailer safely be? tongue weight the vehicle can carry. See “Weight of the Trailer Tongue” later in this section for more information. It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important.
2WD Extended Cab Automatic Transmission, 2.9L Engine Automatic Transmission, 3.7L Engine Manual Transmission, 2.9L Engine Axle Ratio Maximum Trailer Weight GCWR* 3.73 3,100 lbs (1 406 kg) 7,000 lbs (3 175 kg) 3.73 4,000 lbs (1 814 kg) 9,000 lbs (4 082 kg) 3.73 2,100 lbs (952 kg) 6,000 lbs (2 722 kg) 2WD Crew Cab Automatic Transmission, 2.9L Engine Automatic Transmission, 3.7L Engine Manual Transmission, 2.9L Engine Axle Ratio Maximum Trailer Weight GCWR* 3.
4WD Extended Cab Automatic Transmission, 2.9L Engine Automatic Transmission, 2.9L Engine Automatic Transmission, 3.7L Engine Manual Transmission, 2.9L Engine Manual Transmission, 2.9L Engine Axle Ratio Maximum Trailer Weight GCWR* 3.73 2,900 lbs (1 315 kg) 7,000 lbs (3 175 kg) 4.10 2,900 lbs (1 315 kg) 7,000 lbs (3 175 kg) 3.73 4,000 lbs (1 814 kg) 9,000 lbs (4 082 kg) 3.73 1,900 lbs (861 kg) 6,000 lbs (2 722 kg) 4.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle. If you have a lot of options, equipment, passengers or cargo in your vehicle, it will reduce the tongue weight your vehicle can carry, which will also reduce the trailer weight your vehicle can tow.
After you’ve loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they aren’t you may be able to get them right simply by moving some of the items around in the trailer. Trailering may be limited by the vehicle’s ability to carry tongue weight. Tongue weight cannot cause the vehicle to exceed the GVWR (Gross Vehicle Weight Rating) or the RGAWR (Rear Gross Axle Weight Rating).
But let’s say your specific vehicle is equipped with some of the latest options and you have a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well. You may add 300 lbs (136 kg) to the front axle weight and 400 lbs (181 kg) to the rear axle weight. Your vehicle now weighs: You may go further and think you must limit tongue weight to less than 1,000 lbs (454 kg) to avoid exceeding GVWR. But, you must still consider the effect on the rear axle.
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the upper limit for cold tires. You’ll find these numbers on the Certification/Tire label located at the bottom of the center pillar on the driver’s side of the vehicle, or see Loading Your Vehicle on page 290. Then be sure you don’t go over the GVWR limit for your vehicle, including the weight of the trailer tongue.
Safety Chains Trailer Brakes You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer. For trailers up to 2,000 lbs (907 kg) you may attach the safety chains to the attaching points on the bumper.
Driving with a Trailer Following Distance Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Making Turns Notice: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. Your vehicle could be damaged. Avoid making very sharp turns while trailering. When you’re turning with a trailer, make wider turns than normal. Do this so your trailer won’t strike soft shoulders, curbs, road signs, trees or other objects. Avoid jerky or sudden maneuvers. Signal well in advance.
Parking on Hills {CAUTION: You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged. But if you ever have to park your rig on a hill, here’s how to do it: 1. Apply your regular brakes, but don’t shift into PARK (P) yet, or into gear for a manual transmission. When parking uphill, turn your wheels away from the curb.
Maintenance When Trailer Towing Trailer Recommendations Your vehicle will need service more often when you’re pulling a trailer. See Scheduled Maintenance on page 445 for more on this. Things that are especially important in trailer operation are automatic transmission fluid (don’t overfill), engine oil, axle lubricant, belt, cooling system and brake system. Each of these is covered in this manual, and the Index will help you find them quickly.
Section 5 Service and Appearance Care Service ........................................................ 322 Accessories and Modifications ................... 323 California Proposition 65 Warning .............. 323 Doing Your Own Service Work .................. 324 Adding Equipment to the Outside of Your Vehicle ...................................... 325 Fuel ............................................................. 325 Gasoline Octane ........................................
Section 5 Service and Appearance Care Bulb Replacement ....................................... 370 Halogen Bulbs ........................................... 370 Headlamps ................................................ 371 Front Turn Signal, Parking and Daytime Running Lamps (DRL) ........................... 372 Center High-Mounted Stoplamp (CHMSL) ................................ 372 Taillamps, Turn Signal, Stoplamps and Back-up Lamps ............................... 373 License Plate Lamp ..............
Section 5 Service and Appearance Care Appearance Care ........................................ 424 Cleaning the Inside of Your Vehicle .......... 424 Fabric/Carpet ............................................. 425 Leather ...................................................... 426 Instrument Panel, Vinyl, and Other Plastic Surfaces ..................................... 427 Care of Safety Belts .................................. 427 Weatherstrips ............................................
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. 322 We hope you will want to keep your GM vehicle all GM.
Accessories and Modifications California Proposition 65 Warning When you add non-GM accessories to your vehicle they can affect your vehicle’s performance and safety, including such things as, airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like anti-lock brakes, traction control and stability control. Some of these accessories may even cause malfunction or damage not covered by warranty.
Doing Your Own Service Work {CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task. • Be sure to use the proper nuts, bolts, and other fasteners. English and metric fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt.
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airflow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle. Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle.
California Fuel Additives If your vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be affected.
Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber parts. That damage would not be covered under your warranty. Some gasolines that are not reformulated for low emissions may contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT.
Filling the Tank {CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling your vehicle. This is against the law in some places.
{CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way. Be careful not to spill fuel. Do not top off or overfill the tank and wait a few seconds after you have finished pumping before removing the nozzle.
Filling a Portable Fuel Container Checking Things Under the Hood {CAUTION: Never fill a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense gasoline only into approved containers. • Do not fill a container while it is inside a vehicle, in a vehicle’s trunk, pickup bed, or on any surface other than the ground.
Hood Release To open the hood, do the following: 1. Pull the handle with this symbol on it. It is located inside the vehicle on the lower left side of the instrument panel. Before closing the hood, be sure all the filler caps are on properly. Then lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the hood and return the prop to its retainer. Lower the hood 10 to 12 inches (25 to 30 cm) above the vehicle and release it to latch fully.
Engine Compartment Overview When you open the hood on the 2.9L engine (3.
A. Windshield Washer Fluid. See “Adding Washer Fluid” under Windshield Washer Fluid on page 356. B. Engine Coolant Recovery Tank. See Engine Coolant on page 345. C. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 338. D. Power Steering Fluid Reservoir (low in engine compartment). See Power Steering Fluid on page 355. E. Automatic Transmission Fluid Dipstick (If Equipped). See “Checking the Fluid Level” under Automatic Transmission Fluid on page 339. F. Engine Oil Fill Cap.
When to Add Engine Oil If the oil is below the cross-hatched area (L), you will need to add at least one quart/liter of oil. But you must use the right kind. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 439. Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged.
What Kind of Engine Oil to Use These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Look or two things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. You should look for and use only an oil that meets GM Standard GM6094M.
If you are in an area of extreme cold, where the temperature falls below −20°F (−29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both will provide easier cold starting and better protection for the engine at extremely low temperatures. Engine Oil Additives Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all you will need for good performance and engine protection.
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL message being turned on, reset the system. To reset the Engine Oil Life system, do the following: 1. With the engine off, turn the ignition to ON. 2.
Engine Air Cleaner/Filter When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 50,000 mile (83 000 km) interval. See Scheduled Maintenance on page 445 for more information. If you are driving in dusty/dirty conditions, inspect the filter at each engine oil change.
Automatic Transmission Fluid {CAUTION: Operating the engine with the air cleaner/ filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. If it is not there and the engine backfires, you could be burned. Do not drive with it off, and be careful working on the engine with the air cleaner/filter off. Notice: If the air cleaner/filter is off, a backfire can cause a damaging engine fire.
Notice: Too much or too little fluid can damage your transmission. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Too little fluid could cause the transmission to overheat. Be sure to get an accurate reading if you check your transmission fluid. Wait at least 30 minutes before checking the transmission fluid level if you have been driving: • When outside temperatures are above 90°F (32°C). • At high speed for quite a while.
Then, without shutting off the engine, follow these steps: 1. Flip the handle up and then pull out the dipstick and wipe it with a clean rag or paper towel. The automatic transmission dipstick handle with this symbol on it is located in the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 332 for more information on location. 2. Push it back in all the way, wait three seconds and then pull it back out again. 3.
How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See Recommended Fluids and Lubricants on page 455. Add fluid only after checking the transmission fluid while it is hot. A cold check is used only as a reference. If the fluid level is low, add only enough of the proper fluid to bring the level up to the HOT area for a hot check. It does not take much fluid, generally less than one pint (0.5 L). Do not overfill.
Then, follow these steps: How to Add Fluid Here is how to add fluid. Refer to the Maintenance Schedule to determine what kind of fluid to use. See Recommended Fluids and Lubricants on page 455. 1. Remove the filler plug. 2. Add fluid at the filler plug hole. Add only enough fluid to bring the fluid level up to the bottom of the filler plug hole. 3. Install the filler plug. Be sure the plug is fully seated. 1. Remove the filler plug. 2.
When to Check and What to Use Hydraulic Clutch The hydraulic clutch linkage in your vehicle is self-adjusting. The clutch master cylinder reservoir is filled with hydraulic clutch fluid. The hydraulic clutch fluid reservoir cap has this symbol on it. See Engine Compartment Overview on page 332 for reservoir location. It is not necessary to regularly check clutch fluid unless you suspect there is a leak in the system. Adding fluid will not correct a leak.
How to Check and Add Fluid The proper fluid should be added if the level does not reach the bottom of the diaphragm when it is in place in the reservoir. See the instructions on the reservoir cap. Engine Coolant The cooling system in your vehicle is filled with DEX-COOL® engine coolant. This coolant is designed to remain in your vehicle for five years or 150,000 miles (240 000 km), whichever occurs first, if you add only DEX-COOL® extended life coolant.
What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. {CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture.
Adding Coolant Checking Coolant The coolant recovery tank cap has this symbol on it. If you need more coolant, add the proper DEX-COOL® coolant mixture at the coolant recovery tank. {CAUTION: It is located toward the rear of the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 332 for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at FULL COLD, or a little higher.
Add coolant mixture at the recovery tank, but be careful not to spill it. {CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Engine Overheating A coolant temperature gage is on the instrument panel. See Engine Coolant Temperature Gage on page 189. The air conditioning might stop working if the engine is too hot. This is normal and helps cool the engine.
CAUTION: (Continued) If you keep driving when your engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool. Notice: If your engine catches fire because you keep driving with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by your warranty.
Cooling System When you decide it is safe to lift the hood, here is what you will see: A. Coolant Recovery Tank B. Engine Cooling Fan C. Radiator Pressure Cap If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. 350 When the engine is cold, the coolant level should be at least up to the FULL COLD mark.
{CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle. Notice: Engine damage from running your engine without coolant is not covered by your warranty.
How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL® engine coolant at the coolant recovery tank. See Engine Coolant on page 345 for more information. {CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will.
How to Add Coolant to the Radiator {CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot. Wait for the cooling system and radiator pressure cap to cool if you ever have to turn the pressure cap. 1.
3. Fill the radiator with the proper DEX-COOL® coolant mixture, up to the base of the filler neck. See Engine Coolant on page 345 for more information about the proper coolant mixture. 4. Fill the coolant recovery tank to the FULL COLD mark. 5. Reinstall the cap on the coolant recovery tank, but leave the radiator pressure cap off. 354 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. 7.
Engine Fan Noise This vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the clutch is not engaged. This improves fuel economy and reduces fan noise. Under heavy vehicle loading, trailer towing and/or high outside temperatures, the fan speed increases when the clutch engages. So you may hear an increase in fan noise.
How to Check Power Steering Fluid 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag. 4. Replace the cap and completely tighten it. 5. Then remove the cap again and look at the fluid level on the dipstick. The level should be between the ADD and FULL marks. If necessary, add only enough fluid to bring the level up to the proper range.
Notice: • When using concentrated washer fluid, follow the manufacturer’s instructions for adding water. • Do not mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water does not clean as well as washer fluid. • Fill your washer fluid tank only three-quarters full when it is very cold. This allows for expansion if freezing occurs, which could damage the tank if it is completely full.
So, it is not a good idea to top off the brake fluid. Adding brake fluid will not correct a leak. If you add fluid when your linings are worn, then you will have too much fluid when you get new brake linings. You should add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system. {CAUTION: If you have too much brake fluid, it can spill on the engine. The fluid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged.
What to Add When you do need brake fluid, use only DOT-3 brake fluid. Use new brake fluid from a sealed container only. See Recommended Fluids and Lubricants on page 455. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This will help keep dirt from entering the reservoir. {CAUTION: With the wrong kind of fluid in the brake system, the brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper brake fluid.
Brake Wear Your vehicle has front disc brakes and rear drum brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal firmly. {CAUTION: The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident.
Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you make a brake stop, the brakes adjust for wear. If you do not, the brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between the front and rear brakes can change — for the worse.
Vehicle Storage Jump Starting If you are not going to drive your vehicle for 25 days or more, remove the black, negative (−) cable from the battery. This will help keep your battery from running down. If your vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. {CAUTION: {CAUTION: Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful.
Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged.
4. Open the hoods and locate the positive (+) and negative (−) terminal locations on the other vehicle. Your vehicle has a remote positive (+) and a remote negative (−) jump starting terminal. See Engine Compartment Overview on page 332 for more information on the terminal locations. {CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light.
{CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one.
7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery.
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery. 4. Disconnect the red positive (+) cable from the other vehicle. Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part or Remote Negative (−) Terminal B.
Rear Axle When to Check and Change Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant The proper level is from 0 to 3/8 inch (0 mm to 10 mm) below the bottom of the filler plug hole, located on the rear axle. What to Use See Recommended Fluids and Lubricants on page 455 to determine which kind of lubricant to use.
Front Axle When to Check and Change Lubricant It is not necessary to regularly check your front axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant A. Drain Plug B. Filler Plug If the level is below the bottom of the filler plug hole, located on the transfer case, you’ll need to add some lubricant.
If the level is below the bottom of the filler plug hole, located on the front axle, you may need to add some lubricant. When the differential is cold, add enough lubricant to raise the level to 1/2 inch (12 mm) below the filler plug hole. When the differential is at operating temperature (warm), add enough lubricant to raise the level to the bottom of the filler plug hole. What to Use See Recommended Fluids and Lubricants on page 455 to determine what kind of lubricant to use.
Headlamps A. Low-Beam Headlamp/Daytime Running Lamps (DRL) B. High-Beam Headlamp To replace one of these bulbs, do the following: 1. Open the hood. See Hood Release on page 331 for more information. 2. Reach in and access the bulb sockets from inside the engine compartment. 3. Turn the bulb socket counterclockwise to remove it from the headlamp assembly and pull it straight out. 4. Unplug the electrical connector from the old bulb by releasing the clips on the bulb socket. 5.
Front Turn Signal, Parking and Daytime Running Lamps (DRL) 4. Holding the socket, pull the old bulb to release it from the bulb socket. 5. Push the new bulb into the socket until it clicks. To replace one of these bulbs, do the following: 1. Open the hood. See Hood Release on page 331 for more information. 6. Insert the bulb socket into the lamp assembly and turn it clockwise to secure. 7. Close the hood. Center High-Mounted Stoplamp (CHMSL) To replace the CHMSL bulb, do the following: 1.
4. Push the new bulb into the socket until it clicks. 5. Insert the bulb socket into the lamp assembly and turn it clockwise to secure. 6. Reinstall the lamp assembly and tighten the screws. 2. Remove the two rear lamp assembly screws near the tailgate latch. Taillamps, Turn Signal, Stoplamps and Back-up Lamps A. Stoplamp/Taillamp B. Turn Signal/Taillamp C. Back-up Lamp To replace one of these bulbs, do the following: 1. Open the tailgate. See Tailgate on page 108 for more information. 3.
License Plate Lamp To replace one of these bulbs, do the following: Replacement Bulbs Exterior Lamp Center High-Mounted Stoplamp (CHMSL) License Plate Bulb Bulb Number 912 W5W Headlamps 1. Reach under the rear bumper for the bulb socket. 2. Turn the bulb socket counterclockwise and pull the bulb socket out of the connector. 3. Pull the old bulb straight out from the bulb socket. 4. Push the new bulb straight in until it clicks to secure it. 5.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Scheduled Maintenance on page 445 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on page 458. Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by your warranty.
4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully inserted. 5. Be sure that the notches are locked by the bottom claws. Make sure that all other claws are properly locked on both sides of the insert slots. 376 A. Claw in Notch B. Correct Installation C. Incorrect Installation 6.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle. {CAUTION: Poorly maintained and improperly used tires are dangerous. • Overloading your vehicle’s tires can cause overheating as a result of too much friction.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. (A) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail.
(D) Tire Identification Number (TIN): The letters and numbers following DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.
(B) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identification Number (TIN): The Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) P-Metric Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall.
Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission/transaxle, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio: The relationship of a tire’s height to its width.
GAWR RR: Gross Axle Weight Rating for the rear axle. See Loading Your Vehicle on page 290. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.
Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided.
Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right. It is not.
How to Check Tire Pressure Monitor System Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are underinflated. Check the tire’s inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Your vehicle has a Tire Pressure Monitor System (TPMS).
For additional information and details about the DIC operation and displays see DIC Controls and Displays on page 196 and DIC Warnings and Messages on page 200. You may notice, during cooler weather conditions, that the low tire pressure warning light and the DIC LOW TIRE message may come on when the vehicle is first started, and then turn off as you start to drive. This may be an early indicator that the air pressure in the tire(s) is getting low and needs to be inflated to the proper pressure.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
TPMS Sensor Identification Codes Each TPMS sensor has a unique identification code. Any time you replace one or more of the TPMS sensors or rotate your vehicle’s tires, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver’s side front tire, passenger’s side front tire, passenger’s side rear tire, and driver’s side rear tire using a TPMS diagnostic tool. See your dealer for service.
5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire’s air pressure for 10 seconds, then stop and listen for a single horn chirp. The single horn chirp should sound within 15 seconds, confirming that the sensor identification code has been matched to this tire and wheel position. If you do not hear the confirming single horn chirp, turn the ignition switch to LOCK and start over beginning with Step 2.
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
{CAUTION: When rotating your tires, always use one of the correct rotation patterns shown here. If your vehicle has a compact spare tire or a spare tire that does not match your vehicle’s road tires and wheels, in size and type, do not include the spare in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. For the location of the Tire and Loading Information label see Loading Your Vehicle on page 290.
When It Is Time for New Tires One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Some commercial truck tires may not have treadwear indicators. You need a new tire if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber.
Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Specification (TPC spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
CAUTION: (Continued) Your vehicle may have a compact spare tire and wheel assembly. If the vehicle has a compact spare tire and wheel, they have the same overall diameter as your vehicle’s full-size tires and wheels. Because they were designed and developed for use on your vehicle, it is all right to drive your vehicle with the compact spare installed properly. Compact spare tires are designed for temporary use only. See Spare Tire on page 422.
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover. Additionally, if your vehicle has electronic systems such as, anti-lock brakes, traction control, and electronic stability control, the performance of these systems can be affected.
Uniform Tire Quality Grading Treadwear Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Temperature – A, B, C Wheel Alignment and Tire Balance The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Your dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, and wheel nuts for your vehicle.
Tire Chains CAUTION: {CAUTION: If your vehicle has P225/75R15, P265/ 75R15, P235/75R15, or P235/50R18 size tires, do not use tire chains. They can damage your vehicle because there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. See Hazard Warning Flashers on page 160 for more information. {CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1. Set the parking brake firmly. 2.
When your vehicle has a flat tire, use the following example as a guide to assist you in the placement of the wheel blocks. Crew Cab For crew cab models, the jack and wheel blocks are located under the driver’s side rear seat. For regular and extended cab vehicles, the jack and wheel blocks are located under the cover at the center of the vehicle behind the front seats. The following information will tell you next how to use the jack and change a tire.
To access the tools, do the following: 1. Move the seats forward to access the cover. 3. Remove the wheel blocks and the wheel block retainer by turning the wing nut counterclockwise. 4. Put the wheel blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire on the other side, at the opposite end of the vehicle. 5. Locate the wing nut used to retain the storage bag and tools which is under the front passenger’s seat.
A. Jack Handle Extensions B. Jack C. Extension Tool D. Wheel Wrench E. Wheel Blocks 1. Assemble the wheel wrench (D) and the jack handle extensions (A). 2. Insert the hoist end (chiseled end) of the extension tool (C) through the hole in the rear bumper and into the funnel-shaped guide. The chiseled end of the extension is used to lower the spare tire.
3. Turn the wheel wrench (D) counterclockwise to lower the spare tire to the ground. Continue to turn the wheel wrench until the spare tire can be pulled out from under the vehicle. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower. See Secondary Latch System on page 414. Removing the Flat Tire and Installing the Spare Tire Use the following pictures and instructions as a guide in removing the flat tire and raising the vehicle. 4.
1. Remove the center cap by placing the chisel end of the wheel wrench (E) into one of the slots on the wheel and gently prying the cap out. If your vehicle has the Xtreme package, remove each wheel nut cap with the wheel wrench and remove the center cap by hand. 2. Use the wheel wrench to loosen all the wheel nuts by turning it counterclockwise. Do not remove the wheel nuts yet.
{CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. {CAUTION: Front Position Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle. 408 3.
Front Position Rear Position If the flat tire is on the front of the vehicle, position the jack to the rear of the front tire in the pocket off of the frame. If the flat tire is on the rear, position the jack under the rear axle and get as close as possible to the shock absorber. 4. Make sure the jack head is positioned so that the rear axle is resting securely between the grooves that are on the jack head. 5. Turn the wheel wrench clockwise to raise the vehicle.
6. Remove all the wheel nuts and take off the flat tire. CAUTION: (Continued) In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. 7. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. {CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after time. The wheel could come off and cause an accident.
{CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 9. Put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held against the hub.
{CAUTION: Rear Position 10. Turn the wheel wrench counterclockwise to lower the vehicle. Lower the jack completely. 412 Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification.
Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 439 for the wheel nut torque specification. 11. Tighten the wheel nuts firmly in a crisscross sequence as shown by turning the wheel wrench clockwise. When you reinstall the regular wheel and tire, you must also reinstall the center cap.
Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly that has a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle. For the secondary latch to work, the spare must be installed with the valve stem pointing down. See Storing a Flat or Spare Tire and Tools on page 418. To release the spare tire from the secondary latch, do the following: 1. Check under the vehicle to see if the cable end fitting is visible.
3. Loosen the cable by turning the wheel wrench counterclockwise three or four turns. 4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue with Step 5 under Removing the Spare Tire and Tools on page 403. 5. Turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed. 7. Place the bottom edge of the jack (A) on the wheel blocks (B), separating them so that the jack is balanced securely. 6.
8. Attach the jack handle, extension, and wheel wrench to the jack and place it (with the wheel blocks) under the vehicle towards the front of the rear bumper. Position the center lift point of the jack under the wheel. 9. Turn the wheel wrench clockwise to raise the jack until it lifts the tire. 10. Continue raising the jack until the tire stops moving upward and is held firmly in place, the secondary latch has released, and the tire is balancing on the jack. 416 11.
{CAUTION: Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out from the under spare. 13. Disconnect the jack handle from the jack and carefully remove the jack. Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other hand.
Storing a Flat or Spare Tire and Tools {CAUTION: Store the tire under the rear of the vehicle in the spare tire carrier. Use the following art and text to help you. 1. Put the tire on the ground at the rear of the vehicle with the valve stem pointed down. Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
3. Attach the wheel wrench and extensions together as shown. 4. Insert the hoist end of the extension through the hole in the rear bumper and into the funnel-shaped guide. 5. Turn the wheel wrench clockwise to raise the tire part way up. Make sure the retainer is seated in the wheel opening and the valve stem is pointed down. 6. Raise the tire fully against the underside of the vehicle by turning the wheel wrench clockwise until you feel it skip twice. You cannot overtighten the cable.
To store the tools, do the following: 1. Return the wheel wrench, jack extensions and the storage bag to the locations described under Removing the Spare Tire and Tools on page 403. 2. Install the wheel blocks first. Then install the jack. 3. Secure the items in the vehicle as shown next. 7. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire.
A. Jack B. Wheel Blocks C. Wing Nut Regular/Extended Cab Crew Cab A. Jack B. Wheel Blocks C.
Spare Tire Compact Spare Tire Your vehicle may have a compact spare tire. Although the compact spare tire was fully inflated when your vehicle was new, it can lose air over time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). Notice: If your vehicle has four-wheel drive and the compact spare tire is installed on your vehicle, do not drive in four-wheel drive until you can have your flat tire repaired and/or replaced.
Full-Size Spare Tire Your vehicle may have a full-size spare tire, which, when new, was fully inflated. A spare tire may lose air over time, so check its inflation pressure regularly. See Inflation - Tire Pressure on page 385 and Loading Your Vehicle on page 290 for information regarding proper tire inflation and loading your vehicle.
Appearance Care Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery. It is important to keep your upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible.
Do not clean your vehicle using the following cleaners or techniques: • Never use a knife or any other sharp object to remove a soil from any interior surface. • Never use a stiff brush. It can cause damage to your vehicle’s interior surfaces. • Never apply heavy pressure or rub aggressively with a cleaning cloth. Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal. • Use only mild, neutral-pH soaps.
4. Continue to gently rub the soiled area until the cleaning cloth remains clean. 5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process that was used with plain water. If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended.
Washing Your Vehicle Cleaning Exterior Lamps/Lenses The paint finish on the vehicle provides beauty, depth of color, gloss retention, and durability. Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 428. The best way to preserve the vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Do not wash the vehicle in the direct rays of the sun. Use a car washing soap.
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years.
Aluminum or Chrome-Plated Wheels Your vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: If you use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s).
Tires Finish Damage To clean the tires, use a stiff brush with tire cleaner. Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Underbody Maintenance Chemical Paint Spotting Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle.
Vehicle Care/Appearance Materials Description Usage Polishing Cloth Wax-Treated Interior and exterior polishing cloth. Tar and Road Oil Remover Removes tar, road oil, and asphalt. Chrome Cleaner and Polish Use on chrome or stainless steel. White Sidewall Tire Cleaner Removes soil and black marks from whitewalls. Vinyl Cleaner Cleans vinyl. Glass Cleaner Removes dirt, grime, smoke and fingerprints. Chrome and Wire Wheel Cleaner Removes dirt and grime from chrome wheels and wire wheel covers.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Certification/Tire and Service Parts labels and the certificates of title and registration. Engine Identification The eighth character in the VIN is the engine code.
Windshield Wiper Fuses Engine Compartment Fuse Block The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow or ice, the wiper will stop until the motor cools. If the overload is caused by some electrical problem, be sure to get it fixed. Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers.
Fuses DRL AUX PWR 1 STOP BLWR S/ROOF 436 Usage Daylight Running Lamps Accessory Power 1 Brake Switch, Stoplamps Climate Control Fan Sunroof (If Equipped) Fuses A/C PWR/SEAT RT HDLP Usage Air Conditioning Control Head, Power Seats Power Seat Circuit Breaker (If Equipped) Passenger’s Side Headlamp
Fuses LT HDLP AUX PWR 2 FOG/LAMP A/C CMPRSR WSW RVC PWR/WNDW FUEL/PUMP STRTR WPR ABS 2 DR/LCK ETC 02 SNSR CRUISE HTD/SEAT AIRBAG Usage Driver’s Side Headlamp Accessory Power 2 Fog Lamps (If Equipped) Air Conditioning Compressor Wiper/Washer Switch Regulated Voltage Control Power Windows (If Equipped) Fuel Pump Starter Solenoid Relay Wiper Anti-lock Brake System 2 (ABS Pump) Power Door Locks (If Equipped) Electronic Throttle Control (ETC) Oxygen Sensors, Air Injection Reactor (AIR) Relay Cruise Control Swit
Fuses REAR PRK LAMP 2 CLSTR TRN/HAZRD FRT TCCM HORN TBC IGN TRNSD RDO ONSTAR CNSTR VENT PCM B Relays DRL BEAM SEL IGN 3 HVAC RAP 438 Usage Driver’s Side Rear Taillamp, Passenger Side Airbag Indicator Lighting, Instrument Panel Dimming Power (2WD/4WD switch lighting) Cluster Turn/Hazard/Courtesy/ Cargo Lamps/Mirrors Transfer Case Control Module Horn Truck Body Controller Ignition Transducers Radio OnStar® Fuel Canister Vent Solenoid Powertrain Control Module (PCM) B Usage Daylight Running Lamps Beam Selec
Capacities and Specifications The following approximate conversion capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 455 for more information. Capacities and Specifications Capacities Application Air Conditioning Refrigerant R134a English Metric For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer for more information. Cooling System 2.9L Engine 10.4 qt 9.8 L 3.
Capacities and Specifications (cont’d) Capacities Application English Metric Automatic 5.0 qt 4.7 L Manual – Two-Wheel Drive 2.3 qt 2.2 L Manual – Four-Wheel Drive 2.4 qt 2.3 L 100 lb ft 140 Y Transmission (Drain and Refill) Wheel Nut Torque All capacities are approximate. When adding, be sure to fill to the appropriate level or as recommended in this manual. Recheck fluid level after filling. Engine Specifications 440 Type VIN Code Transmission Spark Plug Gap 2.
Section 6 Maintenance Schedule Maintenance Schedule ................................ 442 Introduction ............................................... 442 Maintenance Requirements ........................ 442 Your Vehicle and the Environment ............ 442 Using the Maintenance Schedule ............... 443 Scheduled Maintenance ............................. 445 Additional Required Services ..................... 448 Maintenance Footnotes .............................. 449 Owner Checks and Services ......
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.
Using the Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands, or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary.
The services in Scheduled Maintenance on page 445 should be performed when indicated. See Additional Required Services on page 448 and Maintenance Footnotes on page 449 for further information. {CAUTION: Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job.
Scheduled Maintenance When the CHANGE OIL message comes on, it means that service is required for your vehicle. See DIC Warnings and Messages on page 200. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Maintenance I — Use Maintenance I if the CHANGE OIL message comes on within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message comes on 10 months or more since the last service or if the message has not come on at all for one year. Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter.
Scheduled Maintenance (cont’d) Maintenance I Maintenance II Check engine coolant and windshield washer fluid levels and add fluid as needed. Service • • Perform any needed additional services. See “Additional Required Services” in this section. • • Inspect suspension and steering components. See footnote (b). • Inspect engine cooling system. See footnote (c). • Inspect wiper blades. See footnote (d). • Inspect restraint system components. See footnote (e). • Lubricate body components.
Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Additional Required Services Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect fuel system for damage or leaks. • • • • • • Inspect exhaust system for loose or damaged components.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). • Inspect engine accessory drive belt. An Emission Control Service. See footnote (k).
(d) Visually inspect wiper blades for wear or cracking. Replace wiper blades that appear worn or damaged or that streak or miss areas of the windshield. (e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced.
Owner Checks and Services Engine Oil Level Check These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability, and emission control performance of your vehicle. Your GM Goodwrench® dealer can assist you with these checks and services. Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 333 for further details. Be sure any necessary repairs are completed at once.
At Least Once a Month At Least Once a Year Tire Inflation Check Starter Switch Check Visually inspect your vehicle’s tires and make sure they are inflated to the correct pressures. Do not forget to check the spare tire. See Inflation - Tire Pressure on page 385. Check to make sure the spare tire is stored securely. See Changing a Flat Tire on page 402. Tire Wear Inspection Tire rotation may be required for high mileage highway drivers prior to the Engine Oil Life System service notification.
3. On automatic transmission vehicles, try to start the engine in each gear. The vehicle should start only in PARK (P) or NEUTRAL (N). If the vehicle starts in any other position, contact your GM Goodwrench® dealer for service. On manual transmission vehicles, put the shift lever in NEUTRAL (N), push the clutch pedal down halfway, and try to start the engine. The vehicle should start only when the clutch pedal is pushed down all the way to the floor.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK in each shift lever position. • With an automatic transmission, the ignition should turn to LOCK only when the shift lever is in PARK (P). The ignition key should come out only in LOCK. • With a manual transmission, the ignition key should come out only in LOCK. Contact your GM Goodwrench® dealer if service is required.
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. • To check the parking brake’s holding ability: With the engine running and transmission in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only. • To check the PARK (P) mechanism’s holding ability: With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake.
Usage Parking Brake Cable Guides Fluid/Lubricant Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. GM Power Steering Fluid Power Steering (GM Part No. U.S. 89021184, in System Canada 89021186). Automatic Transmission DEXRON®-VI Automatic Transmission Fluid. Manual Transmission Manual Transmission Fluid (GM Part No. U.S. 89021806, in Canada 89021807). Hydraulic Clutch Fluid Hydraulic Clutch (GM Part No. U.S.
Usage Fluid/Lubricant Hood and Door Hinges, Body Door Hinge Pins, Liftgate Multi-Purpose Lubricant, Superlube Hinge and (GM Part No. U.S. 12346241, in Linkage, Canada 10953474). Folding Seats, and Fuel Door Hinge Outer Tailgate Handle Pivot Points and Hinges Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Usage Fluid/Lubricant Weatherstrip Conditioning Weatherstrip Lubricant (GM Part No. U.S. 3634770, in Canada 10953518) or Dielectric Silicone Grease (GM Part No.
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your GM dealer. GM Part Number ACDelco® Part Number 15202408 A1624C 2.9L Engine 88984215 PF46 3.
Engine Drive Belt Routing 2.9L and 3.7L Engine without air 2.9L and 3.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 442. Any additional information from Owner Checks and Services on page 451 can be added on the following record pages. You should retain all maintenance receipts.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 461
Maintenance Record (cont’d) Date 462 Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed
Section 7 Customer Assistance Information Customer Assistance and Information ....... 464 Customer Satisfaction Procedure ............... 464 Online Owner Center ................................. 467 Customer Assistance for Text Telephone (TTY) Users .......................... 468 Customer Assistance Offices ..................... 468 GM Mobility Reimbursement Program ........ 469 Roadside Assistance Program ................... 470 Courtesy Transportation .............................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps 1 and 2, you should file with the BBB Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program. General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims.
Online Owner Center My GM Canada (Canada only) Online Owner Center (United States only) My GM Canada is a password-protected section of gmcanada.com where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease. The Owner Center is a resource for your GM ownership needs. Specific vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center. Any TTY user in the U.S. can communicate with Chevrolet by dialing: 1-800-833-CHEV (2438). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance.
Overseas — Customer Assistance Please contact the local General Motors Business Unit. GM Mobility Reimbursement Program Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P. 11910, Mexico, D.F.
Roadside Assistance Program In the U.S., call 1-800-CHEV-USA (1-800-243-8872) In Canada, call 1-800-268-6800 Service available 24 hours a day, 365 days a year. As the owner of a new Chevrolet vehicle, you are automatically enrolled in the Chevrolet Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road. Who is Covered? Roadside Assistance coverage is for the vehicle operator, regardless of ownership.
• Emergency Tow From a Public Roadway or Highway: Tow to the nearest dealership for warranty service or in the event of a vehicle-disabling accident. Winch-out assistance when the vehicle is mired in sand, mud, or snow. • Flat Tire Change: If your vehicle has a spare tire, installation of the tire in good condition will be covered at no charge. The customer is responsible for the repair or replacement of the tire if not covered by a warrantable failure.
• Trip Interruption Benefits and Assistance: In the event of a warranty related vehicle disablement, while on route and over 250 kilometres from original point of departure, you may qualify for trip interruption expense assistance. This assistance covers reasonable reimbursement of up to a maximum of $500 (Canadian) for (A) meals (maximum of $50/ day), (B) lodging (maximum of $100/night) and (C) alternate ground transportation (maximum of $40/day).
Chevrolet and General Motors of Canada Limited reserve the right to limit services or reimbursement to an owner or driver when, in their sole discretion, the claims become excessive in frequency or type of occurrence. Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notification.
Scheduling Service Appointments Transportation Options When your vehicle requires warranty service, you should contact your dealer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer can help minimize your inconvenience. Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options.
Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used as ‘shuttle service,’ the reimbursement is limited to the associated shuttle allowance and must be supported by original receipts. In addition, for U.S. customers, should you arrange transportation through a friend or relative, limited reimbursement for reasonable fuel expenses may be available. Claim amounts should reflect actual costs and be supported by original receipts.
Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance.
In addition, once GM collects or receives data, GM may: • use the data for GM research needs, • make it available for research where appropriate confidentiality is to be maintained and need is shown, or • share summary data which is not tied to a specific vehicle with non-GM organizations for research purposes. Others, such as law enforcement, may have access to the special equipment that can read the information if they have access to the vehicle or the device that stores the data.
A recycled original equipment GM part, may be an acceptable choice to maintain your vehicle’s originally designed appearance and safety performance, however, the history of these parts is not known. Such parts are not covered by your GM New Vehicle Limited Warranty, and any related failures are not covered by that warranty. Aftermarket collision parts are also available. These are made by companies other than GM and may not have been tested for your vehicle.
If an Accident Occurs Here is what to do if you are involved in an accident. • Try to relax and then check to make sure you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. • If there has been an injury, call 911 for help. Do not leave the scene of an accident until all matters have been taken care of. Move your vehicle only if its position puts you in danger or you are instructed to move it by a police officer.
• Choose a reputable collision repair facility for your vehicle. Whether you select a GM dealer or a private collision repair facility to fix the damage, make sure you are comfortable with them. Remember, you will have to feel comfortable with their work for a long time. • Once you have an estimate, read it carefully and make sure you understand what work will be performed on your vehicle. If you have a question, ask for an explanation. Reputable shops welcome this opportunity.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying General Motors. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French). Or, write: General Motors of Canada Limited Customer Communication Centre, CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 Service Bulletins Service Publications Ordering Information In Canada, the service bulletin reference number can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483). This reference number is needed to order the service bulletin from Helm, Inc.
Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00 US + Processing Fee Without Portfolio: Owner’s Manual only. RETAIL SELL PRICE: $25.
✍ NOTES 484
A Accessories and Modifications ..................... 323 Accessory Power Outlet(s) .......................... 174 Adding Equipment to Your AirbagEquipped Vehicle ....................................... 93 Additives, Fuel ............................................ 326 Add-On Electrical Equipment ....................... 434 Air Cleaner/Filter, Engine ............................. 338 Air Conditioning ........................................... 176 Airbag Passenger Status Indicator .......................
Appearance Care (cont.) Underbody Maintenance ........................... Vehicle Care/Appearance Materials .......... Washing Your Vehicle .............................. Weatherstrips ........................................... Windshield and Wiper Blades ................... Ashtray(s) .................................................... Assist Handles ............................................ Audio System(s) .......................................... AM-FM Radio ........................................
Bulb Replacement ....................................... Center High-Mounted Stoplamp (CHMSL) ............................... Front Turn Signal, Parking and Daytime Running Lamps ....................... Halogen Bulbs ......................................... Headlamps ............................................... License Plate Lamps ................................ Replacement Bulbs .................................. Taillamps, Turn Signal, Stoplamps and Back-up Lamps ..............................
Cleaning Aluminum or Chrome-Plated Wheels ........ 430 Exterior Lamps/Lenses ............................. 428 Fabric/Carpet ........................................... 425 Finish Care .............................................. 428 Inside of Your Vehicle .............................. 424 Instrument Panel, Vinyl, and Other Plastic Surfaces .................................... 427 Leather .................................................... 426 Tires ......................................................
D Daytime Running Lamps ............................. 170 Daytime Running Lamps Indicator Light ....... 195 Defensive Driving ........................................ 246 Disc, MP3 ................................................... 234 Doing Your Own Service Work .................... 324 Dome Lamp ................................................ 173 Dome Lamp Override .................................. 173 Door Locks ....................................................... 104 Power Door Locks .............
Engine (cont.) Coolant Temperature Gage ...................... 189 Drive Belt Routing .................................... 459 Engine Compartment Overview ................ 332 Exhaust ................................................... 136 Fan Noise ................................................ 355 Oil ........................................................... 333 Oil Life System ........................................ 336 Overheating ............................................. 348 Starting .........
G Gage Engine Coolant Temperature .................... Fuel ......................................................... Speedometer ........................................... Tachometer .............................................. Gasoline Octane ..................................................... Specifications ........................................... Glove Box ................................................... GM Mobility Reimbursement Program ..........
J Jump Starting .............................................. 362 K Keyless Entry System ................................. 101 Keys ............................................................. 99 L Labeling, Tire Sidewall ................................. Lamps Battery Run-Down Protection ................... Dome ....................................................... Dome Lamp Override ............................... Electric Power Management ..................... Exterior .............................
Lighting Exit .......................................................... 173 Limited-Slip Rear Axle ................................. 254 Loading Your Vehicle ................................... 290 Lockout Protection ....................................... 107 Locks Door ........................................................ 104 Lockout Protection ................................... 107 Power Door ............................................. 105 Programmable Automatic Door Locks .......
Mirrors Automatic Dimming Rearview with Compass and Temperature Display ....... Automatic Dimming Rearview with OnStar®, Compass and Temperature Display ................................................. Manual Rearview Mirror ........................... Manual Rearview Mirror with OnStar® ...... Outside Convex Mirror ............................. Outside Manual Mirrors ............................ Outside Power Mirrors ............................. MP3 .......................................................
Parking Brake ....................................................... 130 Over Things That Burn ............................ 135 Parking Your Vehicle ................................... 134 Passenger Airbag Status Indicator ............... 184 Passenger Sensing System ........................... 86 Passing ....................................................... 257 Passlock® .................................................... 114 Pickup Conversion to Chassis Cab ..............
Rearview Mirror, Automatic Dimming with OnStar®, Compass and Temperature Display ..................................................... 139 Rearview Mirror with OnStar® ...................... 138 Rearview Mirrors ......................................... 138 Reclining Seatbacks ...................................... 12 Recommended Fluids and Lubricants .......... 455 Recovery Hooks .......................................... 289 Recreational Vehicle Towing ........................
Safety Belts (cont.) Right Front Passenger Position .................. 34 Safety Belt Extender .................................. 42 Safety Belt Use During Pregnancy ............. 34 Safety Belts Are for Everyone .................... 20 Shoulder Belt Height Adjuster .................... 33 Safety Warnings and Symbols ......................... 4 Scheduled Maintenance ............................... 445 Seatback Latches .......................................... 16 Seats Head Restraints ......................
Specifications, Capacities ............................ Speedometer ............................................... Starting Your Engine ................................... Steering ...................................................... Steering Wheel, Tilt Wheel .......................... Storage Areas Cupholder(s) ............................................ Front Armrest Storage Area ...................... Glove Box ................................................ Rear Storage Area ......................
Tires (cont.) Wheel Replacement ................................. When It Is Time for New Tires ................. Towing Recreational Vehicle ................................. Towing a Trailer ....................................... Your Vehicle ............................................. Traction Control System (TCS) .............................. Limited-Slip Rear Axle .............................. Trailer Recommendations .................................... Transmission Fluid, Automatic ..............
W Warning Lights, Gages and Indicators ......... 179 Warnings DIC Warnings and Messages ................... 200 Hazard Warning Flashers ......................... 160 Other Warning Devices ............................ 160 Safety and Symbols ..................................... 4 Vehicle Damage .......................................... 5 Wheels Alignment and Tire Balance ..................... 398 Different Size ........................................... 396 Replacement .....................................
