2009 Chevrolet Traverse Owner Manual Seats and Restraint System ............................... 1-1 Head Restraints .............. 1-2 Front Seats .................... 1-3 Rear Seats .................... 1-9 Safety Belts .................. 1-14 Child Restraints ............. 1-27 Airbag System .............. 1-46 Restraint System Check ...................... 1-59 Features and Controls ...... 2-1 Keys ............................. 2-2 Doors and Locks ............ 2-8 Windows ......................
ii Preface This manual describes features that may or may not be on your specific vehicle. GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, are registered trademarks, and the name Traverse is a trademark of General Motors Corporation. This manual includes the latest information at the time it was printed. GM reserves the right to make changes after that time without further notice.
Preface Safety Warnings and Symbols { CAUTION These mean there is something that could hurt you or other people. A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning. Cautions tell what the hazard is and what to do to avoid or reduce the hazard. Read these cautions.
iv Preface Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. I: Cruise Control B: Engine Coolant Temperature O: Exterior Lamps #: Fog Lamps .
Seats and Restraint System Seats and Restraint System Head Restraints Head Restraints ....................1-2 Front Seats Manual Seats .......................1-3 Seat Height Adjuster ..............1-3 Power Seats .........................1-4 Manual Lumbar .....................1-4 Power Lumbar ......................1-5 Heated Seats .......................1-5 Heated and Cooled Seats ......1-5 Memory Seat and Mirrors .......1-6 Reclining Seatbacks ..............1-8 Rear Seats Rear Seat Operation ........
1-2 Seats and Restraint System Head Restraints The vehicle’s front seats have adjustable head restraints in all outboard seating positions. { CAUTION With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.
Seats and Restraint System Front Seats 1-3 Lift the bar to unlock the seat. Slide the seat to where you want it and release the bar. Try to move the seat with your body to be sure the seat is locked in place. Manual Seats { CAUTION You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
1-4 Seats and Restraint System Power Seats Move the seat forward or rearward by sliding the power seat adjustment control (A) forward or rearward. Manual Lumbar The vehicle may have additional features to adjust the power seat: • Raise or lower the entire seat by moving the power seat adjustment control (A) up or down. • Raise or lower the front part of Driver Seat with Power Seat Control, Power Recline, and Power Lumbar shown A. Power Seat Adjustment Control B. Reclining Seatbacks on page 1-8. C.
Seats and Restraint System Power Lumbar Heated Seats If the seats have power lumbar, the controls used to operate this feature are located on the outboard side of the seats. See “Power Lumbar” under Power Seats on page 1-4 for more information. On vehicles with heated front seats, the controls are located on the center console. To operate the heated seats the engine must be running. To increase or decrease lumbar support, press and hold the front or rear of the control (C).
1-6 Seats and Restraint System z (Heated Seat and Seatback): To Memory Seat and Mirrors heat the entire seat, press the button with the heated seat and seatback symbol. This symbol will appear on the climate control display to indicate that the feature is on. Press the button to cycle through the temperature settings of high, medium, and low and to turn the heated seat off. Indicator bars next to the symbol designate the level of heat selected: three for high, two for medium, and one for low.
Seats and Restraint System See “MEMORY SEAT RECALL” under DIC Vehicle Customization (With DIC Buttons) on page 3-65 for more information. To stop recall movement of the memory feature at any time, press one of the power seat controls, memory buttons, or power mirror buttons. If something has blocked the driver seat while recalling a memory position, the driver seat recall may stop working.
1-8 Seats and Restraint System Reclining Seatbacks Manual Reclining Seatbacks { CAUTION You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving. { CAUTION If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there.
Seats and Restraint System Rear Seats { CAUTION Rear Seat Operation Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt cannot do its job either. In a crash, the belt could go up over your abdomen.
1-10 Seats and Restraint System 3. Place folding armrests in the upright position. Entering and Exiting the Third Row 4. Ensure that the safety belt is unfastened and in the stowed position. { CAUTION Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.
Seats and Restraint System Returning the Seat to the Seating Position Reclining the Seatbacks To return the second row seat to its normal seating position: 1. Leaning forward in the seat, pull the reclining seatback strap (B). 1. Remove objects on the floor behind the second row seat or in the seat tracks on the floor. 2. Move the seatback to the desired position, then release the strap to lock the seatback in place. 2. Pull the seatback rearward until it is locked in place. 3.
1-12 Seats and Restraint System Third Row Seats { CAUTION To fold the seatback: 1. Remove anything on or under the seat. Using the third row seating position while the second row is folded, or pushed forward in the entry position, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place. The third row seats can be folded forward or removed.
Seats and Restraint System 2. The headrest must be locked into place before sitting in the seat. { CAUTION If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 3. Push and pull on the seatback to make sure it is locked in place.
1-14 Seats and Restraint System Remove the bolts from the holes in the floor before installing the seats. 2. Place the seat on the vehicle floor so that the front seat hooks are on the vehicle bars. 3. Reinstall the bolts, and torque to 55 Y (41 lb ft). Pull up on the seat to make sure it is locked in place. 4. Raise the seatback to its upright position. Push and pull on the seatback to make sure it is locked into place. 5. Push the headrest up into position.
Seats and Restraint System A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without safety belts they could have been badly hurt or killed. Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. After more than 40 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter...
1-16 Seats and Restraint System Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel...
Seats and Restraint System With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not.
1-18 Seats and Restraint System Occupants who are not buckled up can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts. First, before you or your passenger(s) wear a safety belt, there is important information you should know. worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Seats and Restraint System Q: What is wrong with this? 1-19 { CAUTION { CAUTION You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs. You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen.
1-20 Seats and Restraint System Q: What is wrong with this? CAUTION (Continued) would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. Q: What is wrong with this? A: The belt is over an armrest. { CAUTION You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt.
Seats and Restraint System Q: What is wrong with this? A: The belt is behind the body. { CAUTION You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries.
1-22 Seats and Restraint System Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see Third Row Seats on page 1-12 for instruction on reconnecting the safety belt to the mini-buckle. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight.
Seats and Restraint System See “Shoulder Belt Height Adjustment” later in this section for instructions on use and important safety information. 6. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull the stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. 1-23 Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions.
1-24 Seats and Restraint System You can move the height adjuster up by pushing up on the shoulder belt guide. After the adjuster is set to the desired position, try to move it down without pushing the button to make sure it has locked into position. Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly.
Seats and Restraint System To access the comfort guide, you will first need to move the headrest forward by pulling on the handle behind the seatback. The comfort guide will now be accessible. 1-25 The elastic cord on the comfort guide is adjustable. You can make it longer or shorter by squeezing both ends of the plastic adjuster. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.
1-26 Seats and Restraint System Safety Belt Use During Pregnancy { CAUTION A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. Safety belts work for everyone, including pregnant women.
Seats and Restraint System The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Child Restraints Older Children Use a booster seat with a lap-shoulder belt until the child passes the below fit test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
1-28 Seats and Restraint System Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. This applies belt force to the child’s pelvic bones in a crash. It should never be worn over the abdomen, which could cause severe or even fatal internal injuries in a crash.
Seats and Restraint System { CAUTION { CAUTION Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt. The child could move too far forward increasing the chance of head and neck injury. The child might also slide under the lap belt. The belt force would then be applied right on the abdomen.
1-30 Seats and Restraint System { CAUTION CAUTION Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms. An infant should be secured in an appropriate restraint. (Continued) restraint in a rear seat.
Seats and Restraint System Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available.
1-32 Seats and Restraint System Child Restraint Systems (A) Rear-Facing Infant Seat A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. (B) Forward-Facing Child Seat (C) Booster Seats A forward-facing child seat (B) provides restraint for the child’s body with the harness.
Seats and Restraint System Securing an Add-On Child Restraint in the Vehicle { CAUTION A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle’s safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual. To help reduce the chance of injury, the child restraint must be secured in the vehicle.
1-34 Seats and Restraint System A label on the sun visor says, “Never put a rear-facing child restraint in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
Seats and Restraint System Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
1-36 Seats and Restraint System Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Seats and Restraint System To assist you in locating the top tether anchors, the top tether anchor symbol is located on the cover or near the anchor. 1-37 The top tether anchors are located at the bottom rear of the seatback for each seating position in the second row. Open the cover to access the anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
1-38 Seats and Restraint System Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. See Where to Put the Restraint on page 1-33 for additional information.
Seats and Restraint System { CAUTION Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed. Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts.
1-40 Seats and Restraint System 2.3. Route, attach and tighten the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a single tether, route the tether over the seatback. If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback.
Seats and Restraint System If the position you are using has a fixed headrest or head restraint and you are using a single tether, route the tether over the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure. 1-41 Securing a Child Restraint in a Rear Seat Position In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
1-42 Seats and Restraint System 3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Seats and Restraint System See Lower Anchors and Tethers for Children (LATCH) on page 1-35 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position. If the top tether is attached to a top tether anchor, disconnect it. Securing a Child Restraint in the Right Front Seat Position The vehicle has airbags.
1-44 Seats and Restraint System install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH) on page 1-35 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
Seats and Restraint System 1-45 7. Push and pull the child restraint in different directions to be sure it is secure. If the airbags are off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6.
1-46 Seats and Restraint System Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impact airbag for the right front passenger. • A roof-rail airbag for the driver, passenger seated directly behind the driver, and the third row outboard passenger position.
Seats and Restraint System { CAUTION { CAUTION Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward. Safety belts help keep you in position before and during a crash. Always wear your safety belt, even with airbags.
1-48 Seats and Restraint System Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger side. Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
Seats and Restraint System { CAUTION Driver Side shown, Passenger Side similar The roof-rail airbags for the driver, right front passenger, passengers behind the driver and right front passenger, and the third row outboard passengers are in the ceiling above the side windows. If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear.
1-50 Seats and Restraint System Frontal airbags may inflate at different crash speeds. For example: • If the vehicle hits a stationary object, the airbags could inflate at a different crash speed than if the vehicle hits a moving object. • If the vehicle hits an object that deforms, the airbags could inflate at a different crash speed than if the vehicle hits an object that does not deform.
Seats and Restraint System 1-51 What Makes an Airbag Inflate? How Does an Airbag Restrain? full or partial ejection in rollover events, although no system can prevent all such ejections. In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator. Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy. The inflator, the airbag, and related hardware are all part of the airbag module.
1-52 Seats and Restraint System The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags. Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle. { CAUTION When an airbag inflates, there may be dust in the air.
Seats and Restraint System Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. United States Canada The words ON and OFF, or the symbol for on and off, are visible during the system check. If you are using remote start, if equipped, to start the vehicle from a distance, you may not see the system check.
1-54 Seats and Restraint System A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. { CAUTION A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
Seats and Restraint System For some children, including children in child restraints, and for very small adults, the passenger sensing system may or may not turn off the right front passenger frontal airbag, depending upon the person’s seating posture and body build. Everyone in the vehicle who has outgrown child restraints should wear a safety belt properly — whether or not there is an airbag for that person.
1-56 Seats and Restraint System If the Off Indicator is Lit for an Adult-Size Occupant 3. Place the seatback in the fully upright position. 4. Have the person sit upright in the seat, centered on the seat cushion, with legs comfortably extended. 5. Restart the vehicle and have the person remain in this position for two to three minutes after the on indicator is lit.
Seats and Restraint System • Liquid pooled on the seat that has not soaked in may make it more likely that the passenger sensing system will enable (turn on) the passenger airbag while a child restraint or child occupant is on the seat. If the passenger airbag is turned on, the on indicator will be lit. If the passenger seat gets wet, dry the seat immediately. If the airbag readiness light is lit, do not install a child restraint or allow anyone to occupy the seat.
1-58 Seats and Restraint System Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Seats and Restraint System Q: Because I have a disability, I have to get my vehicle modified. How can I find out whether this will affect my airbag system? A: If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See Customer Satisfaction Procedure on page 7-1.
1-60 Seats and Restraint System Replacing Restraint System Parts After a Crash { CAUTION A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Features and Controls Features and Controls Keys Keys ...................................2-2 Remote Keyless Entry (RKE) System .....................2-3 Remote Keyless Entry (RKE) System Operation .......2-4 Remote Vehicle Start .............2-6 Doors and Locks Door Locks ..........................2-8 Power Door Locks .................2-8 Delayed Locking ...................2-8 Programmable Automatic Door Locks .........................2-9 Rear Door Security Locks .......2-9 Lockout Protection ...........
2-2 Features and Controls Storage Areas Glove Box ..........................2-52 Cupholders .........................2-52 Instrument Panel Storage ......2-52 Center Console Storage .......2-52 Second Row Center Console ............................2-53 Floor Mats ..........................2-54 Luggage Carrier ..................2-54 Convenience Net .................2-55 Cargo Cover .......................2-55 Cargo Tie Downs ................2-55 Cargo Management System .............................
Features and Controls If you are locked out of the vehicle, call the Roadside Assistance Center. See Roadside Assistance Program on page 7-6. Remote Keyless Entry (RKE) System The Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2.
2-4 Features and Controls Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-3. With Remote Start and Liftgate (Without Remote Start or Liftgate Similar) / (Remote Vehicle Start): For vehicles with this feature, see Remote Vehicle Start on page 2-6 for additional information.
Features and Controls L (Vehicle Locator/Panic Alarm): Press and release to locate the vehicle. The parking lamps flash and the horn sounds three times. Press and hold L for more than two seconds to activate the panic alarm. The parking lamps flash and the horn sounds repeatedly for 30 seconds. The alarm turns off when the ignition is moved to ON/RUN or L is pressed again. The ignition must be in LOCK/OFF for the panic alarm to work.
2-6 Features and Controls Remote Vehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle. If the vehicle has an automatic climate control system, the climate control system defaults to a heating or cooling mode depending on the outside temperatures. If the vehicle does not have an automatic climate control system, the system turns on at the setting the vehicle was set to when the vehicle was last turned off.
Features and Controls 3. If it is the first remote start since the vehicle has been driven, repeat these steps while the engine is still running, to extend the time by 10 minutes for the engine to continue to run. Remote start can be extended one time. After entering the vehicle during a remote start, insert and turn the key to the ON/RUN position to drive the vehicle. If the vehicle is left running it automatically shuts off after 10 minutes unless a time extension has been done.
2-8 Features and Controls Doors and Locks Door Locks CAUTION (Continued) • Young children who get into { CAUTION Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Features and Controls This feature will not operate if the key is in the ignition. Rear Door Security Locks This feature can be programmed by using the Driver Information Center (DIC). See “DELAY DOOR LOCK” under DIC Vehicle Customization (With DIC Buttons) on page 3-65. The vehicle has rear door security locks to prevent passengers from opening the rear doors from the inside. 2-9 To set the locks, insert a key into the slot and turn it to the horizontal position.
2-10 Features and Controls Liftgate CAUTION { CAUTION Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle must be driven with the liftgate, or trunk/hatch open: • Close all of the windows.
Features and Controls Power Liftgate CAUTION Power Liftgate Operation • Adjust the Climate Control { CAUTION Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.
2-12 Features and Controls If the vehicle is shifted out of P (Park) while the power function is in progress, the liftgate power function will continue to completion. If the vehicle is shifted out of P (Park) and the vehicle accelerates before the power liftgate latches closed, the liftgate may reverse to the open position. Cargo could fall out of the vehicle. The power liftgate must be closed and latched before driving.
Features and Controls After removing the obstruction, the power liftgate operation can be used again. If the liftgate comes across more obstacles on the same power cycle, the power function deactivates, and you must manually open or close the liftgate. A message displays, LIFTGATE OPEN, to indicate that the liftgate is open. See Driver Information Center (DIC) on page 3-44 for more information.
2-14 Features and Controls Windows Power Windows { CAUTION { CAUTION Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Features and Controls Press the switch to lower the window. Pull up on the front edge of the switch to raise the window. Express-Down Windows The express-down feature allows the windows to be lowered without holding the switch. Press the window switch fully and release it to activate the express-down feature. The express mode can be canceled by pressing or pulling the switch. Uplevel shown, base similar The power window controls are located on each of the side doors.
2-16 Features and Controls Anti-Pinch Feature Sun Visors The anti-pinch feature is on windows with the express-up feature. If an object is in the way of the window as it is express-closing, or in certain weather conditions like severe icing, the window will stop and open to a factory preset position. The window functions normally once the obstruction is removed. Pull the sun visor down to block glare.
Features and Controls When the door is closed, the security light stops flashing and stays on solid for approximately 30 seconds. The content theft deterrent alarm is not armed until the security light goes off. If the delayed locking feature is active, the alarm is not activated until all doors are closed and the security light goes off. • Press Q when the driver door is closed. The security light comes on solid for approximately 30 seconds and then goes off.
2-18 Features and Controls PASS-Key® III+ Electronic Immobilizer The PASS-Key III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Features and Controls When the PASS-Key® III+ system senses an incorrect key, the vehicle does not start. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light on the instrument panel comes on when trying to start the vehicle, there may be a problem with your theft-deterrent system. Turn the ignition off and try again.
2-20 Features and Controls If the PASS-Key® III+ key is lost or damaged, see your dealer/retailer or a locksmith to have a new key made. The SERVICE THEFT DETERRENT SYSTEM message displays on the Driver Information Center (DIC) when there is a problem with the theft-deterrent system. See DIC Warnings and Messages on page 3-56 for additional information. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle.
Features and Controls Ignition Positions Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer. ( (LOCK/OFF): This position locks the ignition and transmission. The key can be removed in LOCK/OFF. The ignition switch has four different positions.
2-22 Features and Controls Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the ignition key is turned off: • Audio System • Power Windows • Sunroof (if equipped) Power to the windows and sunroof will work up to 10 minutes or until a door is opened. The radio continues to work for 10 minutes or until the driver’s door is opened. For an additional 10 minutes of operation, close all the doors and turn the key to ON/RUN and then back to LOCK/OFF.
Features and Controls Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to let the cranking motor cool down. 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be flooded with too much gasoline.
2-24 Features and Controls 3. Plug the cord into a normal, grounded 110-volt AC outlet. { CAUTION Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4.
Features and Controls press the shift lever button before shifting from P (Park) when the ignition key is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever, then push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of Park on page 2-29. R (Reverse): Use this gear to back up.
2-26 Features and Controls Electronic Range Select (ERS) Mode ERS mode allows you to choose the top-gear limit of the transmission and the vehicle’s speed while driving down hill or towing a trailer. The vehicle has an electronic shift position indicator within the instrument panel cluster. When using the ERS Mode a number will display next to the L, indicating the current gear that has been selected. To use this feature: 1. Move the shift lever to L (Low). 2.
Features and Controls When Tow/Haul is activated the Tow/Haul symbol will come on the instrument panel cluster. See “Tow/Haul Mode” under Towing a Trailer on page 4-25 for more information. Parking Brake Automatic Engine Grade Braking Automatic Engine Grade Braking assists when driving on a downhill grade. It maintains vehicle speed by automatically implementing a shift schedule that uses the engine and the transmission to slow the vehicle.
2-28 Features and Controls Shifting Into Park { CAUTION It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-25. 1.
Features and Controls If torque lock does occur, your vehicle may need to be pushed uphill by another vehicle to relieve the parking pawl pressure, so you can shift out of P (Park). Shifting Out of Park The vehicle is equipped with an electronic shift lock release system.
2-30 Features and Controls Engine Exhaust CAUTION { CAUTION Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes). • The exhaust smells or sounds strange or different. • The exhaust system leaks due to corrosion or damage.
Features and Controls { CAUTION It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
2-32 Features and Controls Automatic Dimming Mirror Operation Outside Power Mirrors Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature comes on and the indicator light illuminates each time the ignition is turned to start. 3. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen. 4. Press either (A) or (B) again to deselect the mirror.
Features and Controls Outside Power Foldaway Mirrors Mirror Adjustment 1. Press (C) to fold the mirrors out to the driving position. 2. Press (D) to fold the mirrors in to the folded position. Resetting the Power Foldaway Mirrors Fold and unfold the mirrors one time using the mirror controls to reset them to their normal position. A popping noise may be heard during the resetting of the power foldaway mirrors. This sound is normal after a manual folding operation.
2-34 Features and Controls Blind Spot Mirrors The blind spot mirror is a small convex mirror built into the upper and outer corner of both outside mirrors. It is designed to increase driver visibility and show objects that may be in the vehicle’s blind zone. Driving with the Blind Spot Mirror The illustration represents how a vehicle appears in the blind spot mirror when a vehicle is approaching the blind zone. 1.
Features and Controls Using the Outside Mirror with the Blind Spot Mirror 1. Set the main mirror so that the side of your vehicle can just be seen and your blind spot mirror has an unobstructed view. 2. When checking for traffic or before changing a lane, look at the main driver/passenger side mirror to observe traffic in the adjacent lane, behind your vehicle. Check the blind spot mirror for a vehicle in the blind zone.
2-36 Features and Controls Object Detection Systems Ultrasonic Rear Parking Assist (URPA) For vehicles with the Ultrasonic Rear Parking Assist (URPA) system, it operates at speeds less than 5 mph (8 km/h), and assists the driver with parking and avoiding objects while in R (Reverse). The sensors on the rear bumper are used to detect the distance to an object up to 8 feet (2.5 m) behind the vehicle, and at least 10 inches (25.4 cm) off the ground.
Features and Controls How the System Works URPA comes on automatically when the shift lever is moved into R (Reverse). The rear display briefly illuminates to indicate the system is working. URPA operates only at speeds less than 5 mph (8 km/h). If the vehicle is above this speed, the red light on the rear display flashes. To be detected, objects must be at least 10 inches (25.4 cm) off the ground and below liftgate level. Objects must also be within 8 feet (2.5 m) from the rear bumper.
2-38 Features and Controls When the System Does Not Seem to Work Properly • A tow bar is attached to the If the URPA system does not activate due to a temporary condition, the message PARK ASSIST OFF displays on the DIC and a red light will be shown on the rear URPA display when the shift lever is moved into R (Reverse). This may occur under the following conditions: • The vehicle’s bumper is • The driver disables the system. • The ultrasonic sensors are not clean.
Features and Controls CAUTION (Continued) So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury, or death. Even though the vehicle has the RVC system, always check carefully before backing up by checking behind and around the vehicle. Vehicles Without Navigation System The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle.
2-40 Features and Controls 3. Select the Rear Camera Options screen button. The Rear Camera Options screen displays. The delay that is received after shifting out of R (Reverse) is approximately 10 seconds. The delay can be cancelled by performing one of the following: • Pressing a hard key on the navigation system. • Shifting in to P (Park). • Reach a vehicle speed of 5 mph (8 km/h). There is a message on the rear vision camera screen that states “Check Surroundings for Safety”. 4.
Features and Controls Symbols To turn the symbols on or off: The navigation system may have a feature that lets the driver view symbols on the navigation screen while using the rear vision camera. The Ultrasonic Rear Park Assist (URPA) system must not be disabled to use the caution symbols. If URPA has been disabled and the symbols have been turned on, the Rear Parking Assist Symbols Unavailable error message may display. See Ultrasonic Rear Parking Assist (URPA) on page 2-36. 1.
2-42 Features and Controls The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper. The area displayed can vary depending on vehicle orientation or road conditions. The distance of the image that appears on the screen differs from the actual distance. When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if: • The RVC is turned off.
Features and Controls • The back of the vehicle is in an accident, the position and mounting angle of the camera can change or the camera can be affected. Be sure to have the camera and its position and mounting angle checked at your dealer/retailer. • There are extreme temperature changes. The rear vision camera system display in the rearview mirror may turn off or not appear as expected due to one of the following conditions. If this occurs the left indicator light on the mirror will flash.
2-44 Features and Controls OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature. Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the first prepaid year, contact OnStar to select a monthly or annual subscription payment plan.
Features and Controls OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days. Hands-Free Calling can also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility.
2-46 Features and Controls How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy. This information usually includes the vehicle’s GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit).
Features and Controls Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
2-48 Features and Controls Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote.
Features and Controls 2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button.
2-50 Features and Controls 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it.
Features and Controls accepted by the Universal Home Remote. The Universal Home Remote indicator light will flash slowly at first and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. Using Universal Home Remote Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends.
2-52 Features and Controls Storage Areas Glove Box Lift the glove box handle up to open it. Use the key to lock and unlock the glove box. Cupholders There are two cupholders, with removable liners, located in front of the center console. There may be cupholders located in the second row seat armrest. To access, pull the armrest down. There are additional cupholders located on each side of the third row seat and in each door. There may be cupholders located at the rear of the center console.
Features and Controls Second Row Center Console 2-53 { CAUTION Never open more than one of the three latches at a time to help avoid personal injury and damage to the console. For vehicles with a second row center console, open each area to access the storage compartment inside. To access the upper storage area, press the upper button (B) and lift up. To access the lower storage area, press the lower button (C) and lift up. The top of the console can be folded forward for increased storage area.
2-54 Features and Controls Floor Mats If the floor mat has a snap retainer, a grommet in the driver side floor mat attaches to a hook on the floor of the vehicle to secure the floor mat. To remove the floor mat, pull the mat towards the rear of the vehicle until the grommet can be removed from the hook. If the floor mat has a knob retainer, a grommet in the floor mat attaches to a knob on the floor of the vehicle to secure the floor mat.
Features and Controls Convenience Net Use the convenience net, located in the rear, to store small loads as far forward as possible. The net should not be used to store heavy loads. Cargo Management System This vehicle has a cargo management system located in the rear of the vehicle. Cargo Cover For vehicles with a cargo cover, it can be used to cover items in the rear of the vehicle. To install the cover, place the loops on each corner of the cover on the four hooks in the rear of the vehicle.
2-56 Features and Controls Sunroof The vehicle may have a sunroof over the front seats and a rear sunroof over the second row seats. The rear sunroof does not open. The switches to operate the front sunroof and rear sunshade are located on the headliner above the rearview mirror. The ignition must be in ON/RUN or ACC/ACCESSORY to operate the sunroof. See Ignition Positions on page 2-21. The front sunshade must be opened and closed manually. Push up on the sunshade handle to open the sunshade.
Instrument Panel Instrument Panel Instrument Panel Overview Instrument Panel Overview .....3-4 Hazard Warning Flashers .......3-5 Horn ....................................3-5 Tilt and Telescopic Steering Wheel ................................3-6 Turn Signal/Multifunction Lever .................................3-6 Turn and Lane-Change Signals ...............................3-6 Headlamp High/Low-Beam Changer .............................3-7 Flash-to-Pass ........................3-7 Windshield Wipers .......
3-2 Instrument Panel Cruise Control Light .............3-43 Highbeam On Light ..............3-43 Tow/Haul Mode Light ...........3-43 Fuel Gage ..........................3-43 Driver Information Center (DIC) Driver Information Center (DIC) .....................3-44 DIC Operation and Displays (With DIC Buttons) .............3-45 DIC Operation and Displays (Without DIC Buttons) .........3-51 DIC Compass .....................3-54 DIC Warnings and Messages .........................
Instrument Panel ✍ NOTES 3-3
3-4 Instrument Panel Instrument Panel Overview
Instrument Panel The main components of the instrument panel are listed here: A. Turn Signal/Multifunction Lever on page 3-6. Windshield Wipers on page 3-7. B. Instrument Panel Cluster on page 3-31. C. Audio Steering Wheel Controls on page 3-125. D. Instrument Panel Storage on page 2-52. E. Audio System(s) on page 3-73 or Navigation/Radio System on page 3-103 (If Equipped). F. Outlet Adjustment on page 3-27. G. Exterior Lamps on page 3-11. Fog Lamps on page 3-13 (If Equipped). H.
3-6 Instrument Panel Tilt and Telescopic Steering Wheel Turn Signal/Multifunction Lever Turn and Lane-Change Signals The steering wheel can be adjusted. The lever on the left side of the steering column includes the following: G : Turn and Lane-Change Signals The adjustment lever is located on the left side of the steering column. Pull the lever down to move the steering wheel up or down and in or out. Pull the lever up to lock the steering wheel in place.
Instrument Panel Turn Signal On Chime Flash-to-Pass 9 (Off): If either one of the turn signals are left on and the vehicle has been driven more than 3/4 mile (1.2 km), a chime will sound. This feature is used to signal to the vehicle ahead that you want to pass. 6 (Delay): Headlamp High/ Low-Beam Changer 2 3 Headlamp High/Low Beam Changer: Push the turn signal/ multifunction lever away from you to turn the high beams on. Pull the lever towards you to return to low beams.
3-8 Instrument Panel Windshield Washer J (Washer Fluid): Press the button located at the end of the turn signal/multifunction lever, to spray washer fluid on the windshield. The wipers clear the windshield and either stop or return to the preset speed. The ignition key must be in ACC/ACCESSORY or ON/RUN for this to work. See Windshield Washer Fluid on page 5-24 Windshield Washer Fluid. { CAUTION In freezing weather, do not use your washer until the windshield is warmed.
Instrument Panel Rear Window Wiper/Washer The rear wiper and rear wash button is located on the instrument panel below the climate control system. Z (Rear Wiper): Press to turn the rear wiper on and off. The wiper speed cannot be changed. Y (Wash): Press to spray washer fluid on the rear window. The window wiper will also come on. Release the button when enough fluid has been sprayed on the window. The rear wiper will run a few more cycles after it is released.
3-10 Instrument Panel Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed. { CAUTION If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control.
Instrument Panel Using Cruise Control on Hills Exterior Lamps How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down. When the brakes are applied the cruise control is disengaged. Turns the automatic light control on or off.
3-12 Instrument Panel 2 (Headlamps): Turns on the headlamps together with the following lamps listed below. A warning chime sounds if the driver door is opened when the ignition switch is off and the headlamps are on. • • • • Parking Lamps Taillamps License Plate Lamps Instrument Panel Lights # (Fog Lamps) (If Equipped): Turns on the fog lamps. See Fog Lamps on page 3-13. Delayed Headlamps Delayed headlamps provide a period of exterior lighting as you leave the area around your vehicle.
Instrument Panel When the DRL are on, the regular headlamps, taillamps, sidemarker, and other lamps are not on. The instrument panel and cluster are also not on. The headlamps automatically change from DRL to the regular headlamps depending on the darkness of the surroundings. The other lamps that come on with the headlamps will also come on. Fog Lamps # (Fog Lamps): For vehicles with fog lamps, the button is located on the exterior lamps control.
3-14 Instrument Panel Courtesy Lamps Dome Lamp Override When a door is opened, the courtesy lamps automatically come on. They make it easier when entering and exiting the vehicle. The lamps can also be turned on manually by fully turning the instrument panel brightness control clockwise. The dome lamp override button is located next to the exterior lamps control.
Instrument Panel 3-15 Delayed Entry Lighting Delayed Exit Lighting Parade Dimming Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed entry lighting to work.
3-16 Instrument Panel When the battery’s state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high.
Instrument Panel Accessory Power Outlet(s) Accessory power outlets let you plug in auxiliary electrical equipment, such as a cellular phone. The vehicle may have four accessory power outlets. They are located on the instrument panel below the climate controls, under the front center console cupholders, at the rear of the center console, and in the rear cargo area. To use the outlets, remove the cover. When not in use, always cover the outlet with the protective cap.
3-18 Instrument Panel Power Outlet 115 Volt Alternating Current For vehicles with this power outlet, it can be used to plug in electrical equipment that uses a maximum limit of 150 watts. An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in ON/RUN and equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected.
Instrument Panel Climate Controls Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. 3-19 Temperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature of the air flowing from the system. Air Delivery Mode Control: Turn clockwise or counterclockwise to change the current airflow mode. By positioning the right knob between two modes, a combination of those two modes is selected.
3-20 Instrument Panel 6 (Floor): Air is directed to the floor outlets, with some of the air directed to the windshield, side window, and second row floor outlets. In this mode, the system automatically selects outside air. Recirculation cannot be selected while in floor mode. - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents.
Instrument Panel The air conditioning system removes moisture from the air, so a small amount of water might drip under the vehicle while idling or after turning off the engine. This is normal. @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on when recirculation is on. When the engine is turned off, the recirculation mode automatically turns off and must be re-selected when the engine is turned on again.
3-22 Instrument Panel Dual Automatic Climate Control System Display Function The heating, cooling, and ventilation in the vehicle can be controlled with this system. Each time the temperature, mode, or fan control buttons are pressed, the climate control display shows that function along with the inside temperature setting. The outside temperature is displayed on the instrument panel cluster. O (On/Off): Press to turn the climate control system on or off.
Instrument Panel Automatic Operation AUTO (Automatic): The system automatically controls the inside temperature, the air delivery, and the fan speed. To use automatic mode: 1. Press the AUTO button. When AUTO is selected, the current temperature(s) selected and AUTO is shown on the display. The current air delivery mode and fan speed also appear for approximately five seconds. When AUTO is selected, the air conditioning and air inlet are automatically controlled.
3-24 Instrument Panel PASS (Passenger): Press to set the passenger temperature to match the driver temperature setting. The PASS indicator will turn off. When the passenger temperature setting is different than the driver setting, the PASS indicator comes on. Manual Operation The air delivery mode or fan speed can be manually adjusted. D / C (Fan Control): Press to increase or decrease the fan speed. Pressing D or C while in automatic control places the fan speed under manual control.
Instrument Panel While in defrost mode, if the PASS button is pressed, the PASS button indicator flashes three times to show that the passenger climate control system cannot be activated. If the passenger temperature buttons are adjusted while in defrost mode, the driver temperature indicator will change. The passenger temperature will not be displayed. - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents.
3-26 Instrument Panel This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to prevent outside air and odors from entering the vehicle. The recirculation mode cannot be used with floor, defog, or defrosting modes. If recirculation is selected in these modes, the indicator flashes three times and turns off. The air conditioning compressor also comes on when this mode is activated. While in recirculation mode the windows can fog when the weather is cold and damp.
Instrument Panel The climate control system uses the information from these sensors to maintain comfort settings by adjusting the temperature, fan speed, and the air delivery mode. The system may also supply cooler air to the side of the vehicle facing the sun. The recirculation mode will also be used as needed to maintain cool outlet temperatures.
3-28 Instrument Panel Rear Air Conditioning and Heating System Fan Control: Turn clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob to 9 to turn the fan off. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the airflow temperature. Air Delivery Mode Control: Turn to the desired mode to change the airflow direction. H (Vent): A. Fan Control B. Temperature Control C. Air Delivery Mode Control An indicator comes on when the rear system is on.
Instrument Panel Rear Air Conditioning and Heating System and Electronic Climate Controls 3-29 Mimic Mode: This mode matches the rear climate control to the front climate control settings. It comes on when REAR is pressed. Independent Mode: This mode directs rear seating airflow according to the settings of the rear controls. It comes on when any rear control is adjusted. D C (Fan Control): Press the fan up or down buttons to increase or decrease the fan speed.
3-30 Instrument Panel N (Air Delivery Mode Control): Press to manually change the direction of the airflow. Repeatedly press the button until the desired mode appears on the display. H (Vent): Air is directed through the overhead outlets. ) (Bi-Level): Air is directed through the rear floor outlets, as well as the overhead outlets. 6 (Floor): Air is directed through the floor outlets. The rear system floor outlets are located under the third row seats.
Instrument Panel 3-31 Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel is being used, and many other things needed to drive safely and economically.
3-32 Instrument Panel Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). Safety Belt Reminders Driver Safety Belt Reminder Light The driver safety belt reminder light on the instrument panel cluster. The odometer shows how far the vehicle has been driven, in either miles or kilometers. This vehicle has a tamper-resistant odometer.
Instrument Panel Airbag Readiness Light This light shows if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-46. 3-33 { CAUTION If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly.
3-34 Instrument Panel Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate).
Instrument Panel When this light comes on, the Driver Information Center (DIC) also displays the SERVICE BATTERY CHARGING SYSTEM message. See DIC Warnings and Messages on page 3-56 for more information. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner. Voltmeter Gage When the engine is not running, but the ignition is on, this gage displays the battery voltage in DC volts.
3-36 Instrument Panel Brake System Warning Light This vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away. { CAUTION The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash.
Instrument Panel Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. A chime may also sound when the light comes on steady.
3-38 Instrument Panel This light flashes when the StabiliTrak system is active. If the StabiliTrak system warning light comes on and stays on for an extended period of time when the system is turned on, the vehicle needs service. See StabiliTrak® System on page 4-5 for more information. Engine Coolant Temperature Warning Light If this happens pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-22 for more information.
Instrument Panel Tire Pressure Light When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. If the vehicle has a tire pressure monitoring system, the tire pressure light provides information about tire pressures and the Tire Pressure Monitoring System. The light should come on briefly as the engine is started. If it does not, have the vehicle serviced by your dealer/ retailer.
3-40 Instrument Panel If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction.
Instrument Panel Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by checking the following items: • Make sure the fuel cap is fully installed. See Filling the Tank on page 5-7. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere.
3-42 Instrument Panel Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: • The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/RUN and the light is not on.
Instrument Panel Security Light The light goes out when the cruise control is turned off. See Cruise Control on page 3-9 for more information. 3-43 Tow/Haul Mode Light Highbeam On Light This light flashes when the security system is activated. This light comes on when the Tow/Haul mode has been activated. For more information, see Theft-Deterrent Systems on page 2-16. For more information, see Tow/Haul Mode on page 2-26.
3-44 Instrument Panel An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. Driver Information Center (DIC) Here are four things that some owners ask about. None of these show a problem with the fuel gage: Your vehicle has a Driver Information Center (DIC). • At the gas station, the gas pump shuts off before the gage reads full. • It takes a little more or less fuel to fill up than the gage indicated.
Instrument Panel DIC Operation and Displays (With DIC Buttons) DIC Buttons If your vehicle has DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel. See Instrument Panel Overview on page 3-4 for more information. The buttons are the set/reset, customization, vehicle information, and trip/fuel buttons. The button functions are detailed in the following pages.
3-46 Instrument Panel Vehicle Information Menu Items T (Vehicle Information): Press this button to scroll through the following menu items: OIL LIFE Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil’s remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions.
Instrument Panel FRONT TIRES or REAR TIRES On vehicles with the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either pounds per square inch (psi) or kilopascals (kPa). Press the vehicle information button until the DIC displays FRONT TIRES PSI (kPa) LEFT ## RIGHT ##. Press the vehicle information button again until the DIC displays REAR TIRES PSI (kPa) LEFT ## RIGHT ##.
3-48 Instrument Panel COMPASS ZONE SETTING Trip/Fuel Menu Items TRIP A and TRIP B This display will be available if the vehicle has a compass. See DIC Compass on page 3-54 for more information. 3 (Trip/Fuel): Press this button to scroll through the following menu items: Press the trip/fuel button until TRIP A or TRIP B displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for each trip odometer.
Instrument Panel The trip odometer has a feature called the retro-active reset. This can be used to set the trip odometer to the number of miles (kilometers) driven since the ignition was last turned on. This can be used if the trip odometer is not reset at the beginning of the trip. To use the retro-active reset feature, press and hold the set/reset button for at least four seconds.
3-50 Instrument Panel FUEL ECONOMY TIMER FUEL USED Press the trip/fuel button until FUEL ECONOMY displays. The FUEL ECONOMY display shows an estimate of the vehicle fuel economy under a given driving condition at a specific moment. For example, if the vehicle is accelerating and achieving low fuel efficiency this display will show fewer bars, but if the vehicle is cruising on a flat freeway and getting high fuel efficiency, the display will show more bars. Fuel economy cannot be reset.
Instrument Panel DIC Operation and Displays (Without DIC Buttons) If your vehicle does not have DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the trip odometer reset stem located on the instrument panel cluster. Pressing the trip odometer reset stem will also turn off, or acknowledge, DIC messages. The DIC displays trip and vehicle system information, and warning messages if a system problem is detected.
3-52 Instrument Panel To use the retro-active reset feature, press and hold the trip odometer reset stem for at least four seconds. The trip odometer will display the number of miles (mi) or kilometers (km) driven since the ignition was last turned on and the vehicle was moving. Once the vehicle begins moving, the trip odometer will accumulate mileage.
Instrument Panel PARK ASSIST RELEARN REMOTE KEY To access this display, the vehicle must be in P (Park). If your vehicle has the Ultrasonic Rear Parking Assist (URPA) system, press the trip odometer reset stem until PARK ASSIST displays. This display allows the system to be turned on or off. Once in this display, press and hold the trip odometer reset stem to select between ON or OFF. If you choose ON, the system will be turned on. If you choose OFF, the system will be turned off.
3-54 Instrument Panel DISPLAY LANGUAGE DIC Compass To access this display, the vehicle must be in P (Park). This display allows you to select the language in which the DIC messages will appear. To select a language: Your vehicle may have a compass in the Driver Information Center (DIC). 1. Press the trip odometer reset stem until DISPLAY LANGUAGE displays. The zone is set to zone eight upon leaving the factory. Your dealer/ retailer will set the correct zone for your location. 2.
Instrument Panel 3. Press the set/reset button to scroll through and select the appropriate variance zone. If CAL should ever appear in the DIC display, the compass should be calibrated. 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. If the DIC display does not show a heading, for example, N for North, or the heading does not change after making turns, there may be a strong magnetic field interfering with the compass.
3-56 Instrument Panel DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another.
Instrument Panel BATTERY SAVER ACTIVE CHANGE ENGINE OIL SOON This message displays when the system detects that the battery voltage is dropping below expected levels. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. This message displays when the engine oil needs to be changed.
3-58 Instrument Panel DRIVER DOOR OPEN This message displays and a chime sounds if the driver door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gage on page 3-38.
Instrument Panel ENGINE POWER IS REDUCED FUEL LEVEL LOW This message displays and a chime sounds when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating on page 5-22 for further information. This message displays and a chime sounds if the fuel level is low. Refuel as soon as possible. See Fuel Gage on page 3-43 and Fuel on page 5-5 for more information. This message also displays when the vehicle’s engine power is reduced.
3-60 Instrument Panel LEFT REAR DOOR OPEN This message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC. LIFTGATE OPEN This message displays and a chime sounds if the liftgate is open while the ignition is in ON/RUN. Turn off the vehicle and check the liftgate.
Instrument Panel REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “Matching Transmitter(s) to Your Vehicle” under Remote Keyless Entry (RKE) System Operation on page 2-4 and DIC Operation and Displays (With DIC Buttons) on page 3-45 or DIC Operation and Displays (Without DIC Buttons) on page 3-51 for more information.
3-62 Instrument Panel SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument panel cluster. See Charging System Light on page 3-34. Driving with this problem could drain the battery. Turn off all unnecessary accessories. Have the electrical system checked as soon as possible. See your dealer/retailer.
Instrument Panel 3-63 SERVICE TIRE MONITOR SYSTEM SERVICE TRACTION CONTROL SPEED LIMITED TO XXX MPH (KM/H) On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-39. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 5-45 for more information.
3-64 Instrument Panel TIGHTEN GAS CAP TIRE LEARNING ACTIVE This message may display along with the check engine light on the instrument panel cluster if the vehicle’s fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 3-39. Reinstall the fuel cap fully. See Filling the Tank on page 5-7. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere.
Instrument Panel TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 3/4 of a mile (1.2 km). Move the turn signal/multifunction lever to the off position. WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low. Fill the windshield washer fluid reservoir as soon as possible. See Engine Compartment Overview on page 5-10 for the location of the windshield washer fluid reservoir.
3-66 Instrument Panel Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle: DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English. Press the customization button until the PRESS V TO DISPLAY IN ENGLISH screen appears on the DIC display. Press the set/reset button once to display all DIC messages in English.
Instrument Panel To select a setting, press the set/reset button while the desired setting is displayed on the DIC. DRIVER AT KEY OUT: Only the driver’s door will unlock when the key is taken out of the ignition. AUTO DOOR UNLOCK DRIVER IN PARK: Only the driver’s door will unlock when the vehicle is shifted into P (Park). This feature allows you to select whether or not to turn off the automatic door unlocking feature.
3-68 Instrument Panel HORN ONLY: The horn will sound on the second press of the lock button on the RKE transmitter. Keyless Entry (RKE) System Operation on page 2-4 for more information. HORN & LIGHTS (default): The exterior lamps will flash when you press the lock button on the RKE transmitter, and the horn will sound when the lock button is pressed again within five seconds of the previous command. Press the customization button until REMOTE DOOR UNLOCK appears on the DIC display.
Instrument Panel Then press the customization button to scroll through the following settings: OFF: There will be no delayed locking of the vehicle’s doors. ON (default): The doors will not lock until five seconds after the last door or the liftgate is closed. Press the customization button until EXIT LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature.
3-70 Instrument Panel The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed, or the vehicle is no longer off. See Remote Keyless Entry (RKE) System Operation on page 2-4 for more information. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. CHIME VOLUME This feature allows you to select the volume level of the chime.
Instrument Panel EASY EXIT SEAT If your vehicle has this feature, it allows you to select your preference for the automatic easy exit seat feature. See Memory Seat and Mirrors on page 1-6 for more information. Press the customization button until EASY EXIT SEAT appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF (default): No automatic seat exit recall will occur.
3-72 Instrument Panel REMOTE START If your vehicle has this feature, it allows you to turn the remote start off or on. The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry (RKE) transmitter. See Remote Vehicle Start on page 2-6 for more information. Press the customization button until REMOTE START appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Instrument Panel Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs: • The vehicle is shifted out of P (Park). • The vehicle is no longer in ON/RUN. • The trip/fuel or vehicle information DIC buttons are pressed. • The end of the feature settings menu is reached and exited. • A 40 second time period has elapsed with no selection made.
3-74 Instrument Panel Setting the Clock To adjust the time and date: 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN, then press O, to turn the radio on. 2. Press G to display HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year). 3. Press the pushbutton located under any one of the labels to be changed. 4. To increase the time or date, do one of the following: • Press the pushbutton below the selected label. • Press ¨SEEK. • Press \ FWD. • Turn f clockwise. 5.
Instrument Panel Radio(s) Radio with CD 3-75
3-76 Instrument Panel The DVD player is the top slot on the radio faceplate. The player is capable of reading the DTS programmed DVD Audio or DVD Video media. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Radio Data System (RDS) Radio with CD and DVD The vehicle may have one of these radios as its audio system.
Instrument Panel Playing the Radio O (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume. For vehicles with a Rear Entertainment System (RSE), press and hold for more than two seconds to turn off the entire radio and RSE system and to start the parental control feature. Parental control prevents the rear seat occupant from operating the Rear Seat Audio (RSA) system or remote control.
3-78 Instrument Panel Finding a Station BAND: Press to switch between AM, FM, or XM. The selection displays. f (Tune): Turn to select radio stations. ©SEEK ¨: Press to go to the previous or to the next station and stay there. To scan stations, press and hold ©or ¨until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. The radio only seeks and scans stations with a strong signal that are in the selected band.
Instrument Panel To setup the number of favorites pages: 1. Press MENU to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label. Auto Text (Satellite Radio Service, CD, MP3, and WMA features): If additional information is available for the current song being played, Auto Text will automatically page/scroll the information every five seconds above the FAV presets on the radio display. 3.
3-80 Instrument Panel BAL/FADE (Balance/Fade): To adjust the balance or fade: To quickly adjust all speaker and tone controls to the middle position, press f for more than two seconds until a beep sounds. 1. Press f until the speaker control labels display. To quickly adjust all tone and speaker controls to the middle position, press f for more than two seconds until a beep sounds. Radios with CD and DVD fade differently depending on the DVD Media type: 2.
Instrument Panel Finding a Category (CAT) Station CAT (Category): The CAT button is used to find XM™ stations when the radio is in the XM mode. To find XM channels within a desired category: 1. Press BAND until the XM frequency displays. 2. Press CAT to display the category labels. 3. Continue pressing CAT until the desired category name displays. • Radios with CD and DVD can also navigate the category list by pressing s REV or \ FWD. 4.
3-82 Instrument Panel Radio Messages XM™ Satellite Radio Service Calibration Error: The audio system has been calibrated for the vehicle from the factory. If Calibration Error displays, it means that the radio has not been configured properly for the vehicle and it must be returned to your dealer/retailer for service. XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces.
Instrument Panel Care of CDs and DVDs Store CD-R(s) or CD-RW(s) in their original cases or other protective cases and away from direct sunlight and dust. The CD or DVD player scans the bottom surface of the disc. If the surface of a CD is damaged, such as cracked, broken, or scratched, the CD does not play properly or not at all. Do not touch the bottom side of a CD while handling it; this could damage the surface. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge.
3-84 Instrument Panel Z EJECT or CD (Eject): Press and release to eject the disc that is currently playing. A CD ejecting from a radio with CD and DVD, ejects from the bottom slot. A beep sounds and Ejecting Disc displays. Once the disc is ejected, Remove Disc displays. The disc can be removed. If the disc is not removed, after several seconds, the disc automatically pulls back into the player. Z DVD (Eject): Press and release to eject the disc that is currently playing in the top slot.
Instrument Panel CD/AUX (CD/Auxiliary): Press to select between CD, or Auxiliary. • When a CD is in the player the CD icon and a message showing the disc and/or track number displays. • If an auxiliary input device is not connected, “No Input Device Found” displays. DVD/CD AUX (Auxiliary): Press to select between DVD, CD, or Auxiliary. • If an auxiliary input device is not connected, “No Aux Input Device” displays.
3-86 Instrument Panel See “Using the Auxiliary Input Jack(s)” later in this section, or “Audio/Video (A/V) Jacks” under, Rear Seat Entertainment (RSE) System on page 3-114 for more information. CD Messages In some vehicles, depending on audio options, the rear speakers can be muted when the RSA power is turned on. See Rear Seat Audio (RSA) on page 3-123 for more information.
Instrument Panel Using the DVD Player Playing a DVD The DVD player can be controlled by the buttons on the remote control, the RSA system, or by the buttons on the radio faceplate. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 3-114 and Rear Seat Audio (RSA) on page 3-123 for more information. f (Tune): The DVD player is only compatible with DVDs of the appropriate region code that is printed on the jacket of most DVDs.
3-88 Instrument Panel DVD-V (Video) Display Buttons Once a DVD-V is inserted, the radio display menu shows several icons. Press the pushbuttons located under any desired icon during DVD playback. See the icon list below for more information. The rear seat passenger can navigate the DVD-V menus and controls through the remote control. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 3-114 for more information.
Instrument Panel DVD-A (Audio) Display Buttons Once a DVD-A is inserted, the radio display menu shows several icons. Press the pushbuttons located under any desired icon during DVD playback. See the icon list below for more information. The rear seat operator can navigate the DVD-A menus and controls through the remote control. See “Remote Control”, under Rear Seat Entertainment (RSE) System on page 3-114 for more information.
3-90 Instrument Panel Stopping and Resuming Playback To stop playing a DVD without turning off the system, do one of the following: • Press c on the remote control. • Press the pushbutton located under the stop or the play/pause icons displayed on the radio. • If the radio head is sourced to something other than DVD-V, press the DVD/CD AUX button to make DVD-V the active source. To resume DVD playback, do one of the following: • Press r / j on the remote control.
Instrument Panel Using the Auxiliary Input Jack The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug a headphone set into the front auxiliary input jack. Connect an auxiliary input device such as an iPod, laptop computer, MP3 player, CD player, or cassette tape player, etc. to the auxiliary input jack for use as another source for audio listening.
3-92 Instrument Panel If a disc is inserted into top DVD slot, the rear seat operator can turn on the video screen and use the remote control to only navigate the CD tracks through the remote control. See “Using the Auxiliary Input Jack(s)” later in this section, or “Audio/Video (A/V) Jacks” under, Rear Seat Entertainment (RSE) System on page 3-114 for more information. Using an MP3 (Radio with CD) MP3/WMA CD-R or CD-RW Disc The radio plays MP3/WMA files that were recorded on a CD-R or CD-RW disc.
Instrument Panel • The CD player is able to read and play a maximum of 50 folders, 15 playlists, and a combined total of 512 folders and files. • Create a folder structure that makes it easy to find songs while driving. Organize songs by albums using one folder for each album. Each folder or album should contain 18 songs or less. • Avoid subfolders.
3-94 Instrument Panel Empty Directory or Folder Order of Play File System and Naming If a root directory or a folder exists somewhere in the file structure that contains only folders/subfolders and no compressed files directly beneath them, the player advances to the next folder in the file structure that contains compressed audio files. The empty folder does not display.
Instrument Panel Playing an MP3/WMA Insert a CD-R or CD-RW disc partway into the slot label side up. The player pulls it in, and the CD-R or CD-RW should begin playing. Z EJECT: Press to eject the disc. f (Tune): Turn to select MP3/WMA files on the CD-R or CD-RW currently playing. ©SEEK ¨: Press the left SEEK arrow to go to the start of the current MP3/WMA file, if more than ten seconds have played. Press the right SEEK arrow to go to the next MP3/WMA file.
3-96 Instrument Panel h (Music Navigator): Use the music navigator feature to play MP3/WMA files on the CD-R or CD-RW in order by artist or album. Press the pushbutton located below the music navigator label. The player scans the disc to sort the files by artist and album ID3 tag information. It could take several minutes to scan the disc depending on the number of MP3/WMA files recorded to the CD-R or CD-RW disc. The radio can begin playing while it is scanning the disc in the background.
Instrument Panel MP3/WMA Format To create an MP3/WMA disc on a personal computer: • Make sure the MP3/WMA files are recorded on a CD-R or CD-RW disc. • Do not mix standard audio and MP3/WMA files on one disc. • The CD player (lower slot) is able to read and play a maximum combination of 512 files and folders. The DVD player (upper slot) is able to read 255 folders, 15 playlists and 40 sessions. • Create a folder structure that makes it easy to find songs while driving.
3-98 Instrument Panel No Folder Order of Play File System and Naming When the CD-R or CD-RW disc contains only compressed files, the files are located under the root folder. The next and previous folder function does not function on a CD-R or CD-RW that was recorded without folders or playlists. When displaying the name of the folder the radio displays ROOT.
Instrument Panel Playing an MP3/WMA (In Either the DVD or CD Slot) Insert a CD-R or CD-RW disc partway into either the top or bottom slot, label side up. The player pulls it in, and the CD-R or CD-RW should begin playing. Depending on the format of the disc, a softkey menu appears and allows navigation of the disc.
3-100 Instrument Panel ©SEEK ¨: Press the left SEEK arrow to go to the start of the current MP3/WMA file, if more than five seconds have played. If less than five seconds have played, the previous MP3/WMA file plays. Press the right SEEK arrow to go to the next MP3/WMA file. If either SEEK arrow is held, or pressed multiple times, the player continues moving backward or forward through the MP3/WMA files on the CD.
Instrument Panel Once the disc has been scanned, the player defaults to playing MP3/WMA files in order by artist. The current artist playing is shown on the second line of the display between the arrows. To listen to MP3/WMA files by another artist, press the pushbutton located below either arrow button. The disc goes to the next or previous artist in alphabetical order. Continue pressing either button until the desired artist is displayed.
3-102 Instrument Panel XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the XM™ signal.
Instrument Panel Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer. Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer.
3-104 Instrument Panel Bluetooth Controls Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Audio Steering Wheel Controls on page 3-125 for more information. b g (Push To Talk): Press to answer incoming calls, to confirm system information, and to start speech recognition. c x (Phone On Hook): Press to end a call, reject a call, or to cancel an operation.
Instrument Panel 5. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then confirms the name provided. 6. The system responds with “ has been successfully paired” after the pairing process is complete. 7. Repeat Steps 1 through 7 for additional phones to be paired. Listing All Paired and Connected Phones 1. Press and hold b g for two seconds.
3-106 Instrument Panel Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: • Store • Digit Store • Directory Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”.
Instrument Panel Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Store”. The system responds with “Please say the first digit to store” followed by a tone. 3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete.
3-108 Instrument Panel Using the Delete Command The delete command allows specific name tags to be deleted. To use the delete command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete”. The system responds with “Delete, please say the name tag” followed by a tone. 3. Say the name tag to be deleted. The system responds with “Would you like to delete, ? Please say yes or no”. • If the name tag is correct, say “Yes” to delete the name tag.
Instrument Panel 3. Say the entire number without pausing. • If the system recognizes the number, it responds with “OK, Dialing” and dials the number. • If the system does not recognize the number, it confirms the numbers followed by a tone. If the number is correct, say “Yes”. The system responds with “OK, Dialing” and dials the number. If the number is not correct, say “No”. The system will ask for the number to be re-entered. Using the Digit Dial Command 1. Press and hold b g for two seconds.
3-110 Instrument Panel Using the Call Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Call”. The system responds with “Call using . Please say the name tag” followed by a tone. 3. Say the name tag of the person to call. • If the system clearly recognizes the name tag it responds with “OK, calling, ” and dials the number.
Instrument Panel Three-Way Calling Muting a Call Three-Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. 1. While on a call press b g. The system responds with “Ready” followed by a tone. To Mute a call 2. Say “Three-way call”. The system responds with “Three-way call, please say dial or call”. 3.
3-112 Instrument Panel Voice Pass-Thru Voice Pass-Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Voice”.
Instrument Panel Sending a Stored Name Tag During a Call 1. Press b g. The system responds with “Ready” followed by a tone. 2. Say “Send name tag.” The system responds with “Say a name tag to send tones” followed by a tone. 3. Say the name tag to send. • If the system clearly recognizes the name tag it responds with “OK, Sending ” and the dial tones are sent and the call continues.
3-114 Instrument Panel Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle’s audio system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, a video display screen, audio/video jacks, two wireless headphones, and a remote control. See Radio(s) on page 3-75 for more information on the vehicle’s audio/DVD system.
Instrument Panel The wireless headphones have an On/Off button, channel 1/2 switch, and a volume control. Switch the headphones to Off when not in use. Push the power button to turn on the headphones. An indicator light located on the headphones comes on. If the light does not come on, the batteries might need to be replaced. Intermittent sound or static on the headphones can also be an indication of weak batteries. See “Battery Replacement” later in this section for more information.
3-116 Instrument Panel Battery Replacement Audio/Video (A/V) Jacks To change the batteries on the headphones: 1. Turn the screw to loosen the battery door located on the left side of the headphones. Slide the battery door open. Power for auxiliary devices is not supplied by the radio system. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment. 3. Replace the battery door and tighten the door screw.
Instrument Panel How to Change the RSE Video Screen Settings The screen display mode (normal, full, and zoom), screen brightness, and setup menu language can be changed from the on screen setup menu by using the remote control. To change a setting: z. Use n, q, p, o and r to 1. Press 2. navigate and use the setup menu. 3. Press z again to remove the setup menu from the screen.
3-118 Instrument Panel Remote Control To use the remote control, aim it at the transmitter window at the rear of the overhead console and press the desired button. Direct sunlight or very bright light could affect the ability of the RSE transmitter to receive signals from the remote control. If the remote control does not seem to be working, the batteries might need to be replaced. See “Battery Replacement” later in this section.
Instrument Panel O (Power): Press to turn the video screen on and off. P (Illumination): Press to turn the remote control backlight on. The backlight automatically times out after seven to ten seconds if no other button is pressed while the backlight is on. v (Title): Press to return the DVD to the main menu of the DVD. This function could vary for each disc. y (Main Menu): Press to access the DVD menu. The DVD menu is different on every DVD.
3-120 Instrument Panel r (Fast Reverse): Press to quickly reverse the DVD or CD. To stop fast reversing a DVD video, press s. To stop fast reversing a DVD audio or CD, release r. This button might not work when the DVD is playing the copyright information or the previews. { (Subtitles): [ (Fast Forward): d (Camera): Press to change camera angles on DVDs that have this feature when a DVD is playing. The format and content of this function vary for each disc. Press to fast forward the DVD or CD.
Instrument Panel Problem Recommended Action The ignition might not be turned ON/RUN or in ACC/ACCESSORY. The picture does not fill the screen. Check the display mode settings There are black borders on the top in the setup menu by pressing the and bottom or on both sides or it display menu button on the remote looks stretched out. control. In auxiliary mode, the picture moves Check the auxiliary input or scrolls. connections at both devices. The remote control does not work.
3-122 Instrument Panel Problem Sometimes the wireless headphone audio cuts out or buzzes. I lost the remote and/or the headphones. The DVD is playing, but there is no picture or sound. DVD Display Error Messages The DVD display error message depends on which radio the vehicle has. The video screen might display one of the following: Disc Load/Eject Error: This message displays when there are disc load or eject problems.
Instrument Panel Rear Seat Audio (RSA) For vehicles with Rear Seat Audio (RSA), rear seat passengers can listen to and control any of the music sources: radio, CDs, DVDs, or other auxiliary sources. The rear seat passengers can only control the music sources the front seat passengers are not listening to (except on some radios where dual control is allowed).
3-124 Instrument Panel While listening to a disc, press ¨to go to the next track or chapter on the disc. Press ©to go back to the start of the current track or chapter (if more than ten seconds have played). This function is inactive, with some radios, if the front seat passengers are listening to the disc. P (Power): Press to turn the RSA on or off. Volume: Turn to increase or to decrease the volume of the wired headphones.
Instrument Panel When a disc is playing in the CD or DVD changer, press PROG to select the next disc, if multiple discs are loaded. This function is inactive, with some radios, if the front seat passengers are listening to the disc. Audio Steering Wheel Controls w (Next): Press to go to the next radio station stored as a favorite, or the next track if a CD/DVD is playing.
3-126 Instrument Panel SRCE (Source): Press to switch between the radio (AM, FM, XM), CD, and for vehicles with, DVD, front auxiliary, and rear auxiliary. For vehicles with the navigation system, press and hold this button for longer than one second to initiate voice recognition. See “Voice Recognition” in the Navigation System manual for more information. + e − e (Volume): Press to increase or to decrease the radio volume. ¨ (Seek): Press to go to the next radio station while in AM, FM, or XM™.
Instrument Panel Cellular Phone Usage Multi-Band Antenna Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio. If static is received while listening to the radio, unplug the cellular phone and turn it off. The multi-band antenna is located on the roof of the vehicle.
3-128 Instrument Panel ✍ NOTES
Driving Your Vehicle Driving Your Vehicle Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy ............................4-1 Defensive Driving ..................4-2 Drunk Driving .......................4-2 Control of a Vehicle ...............4-3 Braking ................................4-3 Antilock Brake System (ABS) .....................4-4 Braking in Emergencies ..........4-5 StabiliTrak® System ...............4-5 All-Wheel Drive (AWD) System ..............................
4-2 Driving Your Vehicle • Keep vehicle tires properly inflated. • Combine several trips into a { CAUTION Defensive Driving Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition: • Allow enough following distance between you and the driver in front of you. • Focus on the task of driving. Defensive driving means “always expect the unexpected.
Driving Your Vehicle Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured. For persons under 21, it is against the law in every U.S. state to drink alcohol.
4-4 Driving Your Vehicle And, of course, actual stopping distances vary greatly with the surface of the road, whether it is pavement or gravel; the condition of the road, whether it is wet, dry, or icy; tire tread; the condition of the brakes; the weight of the vehicle; and the amount of brake force applied. Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake.
Driving Your Vehicle As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes.
4-6 Driving Your Vehicle The system may be heard or felt while it is working. This is normal and does not mean there is a problem with the vehicle. The system should initialize before the vehicle reaches 20 mph (32 km/h). In some cases, it may take approximately two miles (3.2 km) of driving before the system initializes.
Driving Your Vehicle It may also be necessary to turn off the system when driving in extreme off-road conditions where high wheel spin is required. See If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-16. Traction Control Operation The traction control system is part of the StabiliTrak system. Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary.
4-8 Driving Your Vehicle When using a compact spare tire on the AWD equipped vehicle, the AWD system automatically detects the presence of the compact spare and the AWD is disabled. To restore the AWD operation and prevent excessive wear on the AWD system, replace the compact spare with a full-size tire as soon as possible. See Compact Spare Tire on page 5-77 for more information.
Driving Your Vehicle 4-9 Off-Road Recovery Passing The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. Passing another vehicle on a two-lane road can be dangerous. To reduce the risk of danger while passing: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. • Watch for traffic signs, An emergency like this requires close attention and a quick decision.
4-10 Driving Your Vehicle Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up. Keep trying to steer and constantly seek an escape route or area of less danger. Skidding In a skid, a driver can lose control of the vehicle.
Driving Your Vehicle • • • • Watch for animals. When tired, pull off the road. Do not wear sunglasses. Avoid staring directly into approaching headlamps. • Keep the windshield and all glass on your vehicle clean — inside and out. Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water.
4-12 Driving Your Vehicle Hydroplaning Other Rainy Weather Tips Hydroplaning is dangerous. Water can build up under your vehicle’s tires so they actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. Besides slowing down, other wet weather driving tips include: There is no hard and fast rule about hydroplaning. The best advice is to slow down when the road is wet.
Driving Your Vehicle Highway Hypnosis Hill and Mountain Roads Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest. Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: Other driving tips include: • Keep the vehicle well ventilated. • Keep interior temperature cool.
4-14 Driving Your Vehicle Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand. Drive with caution, whatever the condition. Accelerate gently so traction is not lost.
Driving Your Vehicle { CAUTION Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle is stuck in the snow: • Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe. • Check again from time to time to be sure snow does not collect there.
4-16 Driving Your Vehicle If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow For information about using tire chains on the vehicle, see Tire Chains on page 5-55. Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 4-16. Rocking Your Vehicle to Get It Out If the vehicle has a traction system, it can often help to free a stuck vehicle. Refer to the vehicle’s traction system in the Index.
Driving Your Vehicle { CAUTION Tire and Loading Information Label Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on the vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of the vehicle.
4-18 Driving Your Vehicle Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
Driving Your Vehicle 4-19 Refer to your vehicle’s tire and loading information label for specific information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight. Example 2 A. Vehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg). B. Subtract Occupant Weight 150 lbs (68 kg) × 5 = 750 lbs (340 kg). C. Available Cargo Weight = 250 lbs (113 kg). Example 3 A.
4-20 Driving Your Vehicle Certification/Tire Label Label Example A vehicle specific Certification/ Tire label is attached to the rear edge of the driver’s door. The label shows the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR).
Driving Your Vehicle { CAUTION Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash. • Put things in the cargo area of your vehicle. Try to spread the weight evenly. • Never stack heavier things, like suitcases, inside the vehicle so that some of them are above the tops of the seats. • Do not leave an unsecured child restraint in your vehicle. • When you carry something inside the vehicle, secure it whenever you can.
4-22 Driving Your Vehicle Dinghy Towing If the vehicle is all-wheel-drive, it can be dinghy towed from the front. These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground. These vehicles cannot be towed using a dolly. For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components.
Driving Your Vehicle Notice: If the vehicle is towed without performing each of the steps listed under “Dinghy Towing,” the automatic transmission could be damaged. Be sure to follow all steps of the dinghy towing procedure prior to and after towing the vehicle. Notice: If 65 mph (105 km/h) is exceeded while towing the vehicle, it could be damaged. Never exceed 65 mph (105 km/h) while towing the vehicle. Once the destination is reached: 1. Set the parking brake.
4-24 Driving Your Vehicle Dolly Towing (Front-Wheel-Drive Vehicles Only) 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 5. Remove the key from the ignition. 6. Secure the vehicle to the dolly. 7. Release the parking brake. Towing the Vehicle From the Rear To tow a front-wheel-drive vehicle from the front with two wheels on the ground: 1. Put the front wheels on a dolly. 2. Move the shift lever to P (Park). 3. Set the parking brake.
Driving Your Vehicle Towing a Trailer { CAUTION The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured. The vehicle may also be damaged; the resulting repairs would not be covered by the vehicle warranty. Pull a trailer only if all the steps in this section have been followed.
4-26 Driving Your Vehicle Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police. • Consider using a sway control. See “Hitches” later in this section. • Do not tow a trailer at all during the first 500 miles (800 km) the new vehicle is driven.
Driving Your Vehicle 4-27 Vehicle Maximum Trailer Weight *GCWR Front-Wheel Drive 2,000 lbs (907 kg) 7,500 lbs (3 402 kg) Front-Wheel Drive, V92 Trailer Towing Package 5,200 lbs (2 359 kg) 10,250 lbs (4 649 kg) All-Wheel Drive 2,000 lbs (907 kg) 7,700 lbs (3 493 kg) All-Wheel Drive, V92 Trailer Towing Package 5,200 lbs (2 359 kg) 10,450 lbs (4 740 kg) *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equip
4-28 Driving Your Vehicle After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they aren’t, adjustments might be made by moving some items around in the trailer. Trailering may also be limited by the vehicle’s ability to carry tongue weight. Tongue weight cannot cause the vehicle to exceed the GVWR (Gross Vehicle Weight Rating) or the RGAWR (Rear Gross Axle Weight Rating).
Driving Your Vehicle You may go further and think the tongue weight should be limited to less than 1,000 lbs (454 kg) to avoid exceeding GVWR. But the effect on the rear axle must still be considered. Because the rear axle now weighs 3,100 lbs (1 406 kg), 900 lbs (408 kg) can be put on the rear axle without exceeding RGAWR. The effect of tongue weight is about 1.5 times the actual weight. Dividing the 900 lbs (408 kg) by 1.5 leaves only 600 lbs (272 kg) of tongue weight that can be handled.
4-30 Driving Your Vehicle Safety Chains Trailer Brakes Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer. Follow the manufacturer’s recommendation for attaching safety chains and do not attach them to the bumper.
Driving Your Vehicle Passing More passing distance is needed when towing a trailer. Because the rig is longer, it is necessary to go much farther beyond the passed vehicle before returning to the lane. When turning with a trailer, make wider turns than normal. Do this so the trailer won’t strike soft shoulders, curbs, road signs, trees or other objects. Avoid jerky or sudden maneuvers. Signal well in advance.
4-32 Driving Your Vehicle See Weight of the Trailer earlier in this section. Tow/Haul is most useful under the following driving conditions: Tow/Haul Mode Tow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load. The purpose of the Tow/Haul mode is to: • When pulling a heavy trailer or a • Reduce the frequency and improve the predictability of transmission shifts when pulling a heavy trailer or a large or heavy load.
Driving Your Vehicle Parking on Hills { CAUTION Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface. If parking the rig on a hill: 1. Press the brake pedal, but do not shift into P (Park) yet. Turn the wheels into the curb if facing downhill or into traffic if facing uphill. 2.
4-34 Driving Your Vehicle Basic Trailer Wiring The trailer wiring harness, with a seven-pin connector, is located at the rear of the vehicle and is tied to the vehicle’s frame. The harness connector can be plugged into a seven-pin universal heavy-duty trailer connector available through your dealer/retailer.
Service and Appearance Care Service and Appearance Care Service Service ................................5-3 Accessories and Modifications .......................5-3 California Proposition 65 Warning .............................5-4 California Perchlorate Materials Requirements ........5-4 Doing Your Own Service Work ......................5-4 Adding Equipment to the Outside of the Vehicle ...........5-4 Fuel Fuel ....................................5-5 Gasoline Octane ...................
5-2 Service and Appearance Care Different Size Tires and Wheels .............................5-52 Uniform Tire Quality Grading ............................5-52 Wheel Alignment and Tire Balance ............................5-54 Wheel Replacement .............5-54 Tire Chains .........................5-55 If a Tire Goes Flat ...............5-56 Tire Sealant and Compressor Kit ..................5-57 Tire Sealant and Compressor Kit Storage ......5-64 Changing a Flat Tire ............
Service and Appearance Care Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people.
5-4 Service and Appearance Care California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many fluids, and some component wear by-products contain and/or emit these chemicals.
Service and Appearance Care Fuel Gasoline Specifications Use of the recommended fuel is an important part of the proper maintenance of this vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/ CGSB-3.5 or 3.511 in Canada.
5-6 Service and Appearance Care For customers who do not use TOP TIER Detergent Gasoline regularly, one bottle of GM Fuel System Treatment PLUS, added to the fuel tank at every engine oil change, can help clean deposits from fuel injectors and intake valves. GM Fuel System Treatment PLUS is the only gasoline additive recommended by General Motors. Also, your dealer/retailer has additives that will help correct and prevent most deposit-related problems.
Service and Appearance Care Filling the Tank { CAUTION Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle. Do not use cellular phones. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling the vehicle.
5-8 Service and Appearance Care The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 3-39. If the vehicle has a Driver Information Center (DIC), the TIGHTEN GAS CAP message displays if the fuel cap is not properly installed. { CAUTION If a fire starts while you are refueling, do not remove the nozzle.
Service and Appearance Care Checking Things Under the Hood Hood Release To open the hood, do the following: { CAUTION An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION Things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned.
5-10 Service and Appearance Care Engine Compartment Overview When you lift the hood, here is what you will see:
Service and Appearance Care A. Radiator Pressure Cap. See Cooling System on page 5-17. B. Engine Coolant Recovery Cap. See Cooling System on page 5-17. C. Remote Negative (−) Terminal. See Jump Starting on page 5-29. D. Underhood Fuse Block on page 5-88. E. Remote Positive (+) Terminal. See Jump Starting on page 5-29. F. Power Steering Fluid on page 5-24. G. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-11. H. Engine Oil Dipstick.
5-12 Service and Appearance Care When to Add Engine Oil What Kind of Engine Oil to Use Look for three things: If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-92. Notice: Do not add too much oil.
Service and Appearance Care • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. • American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container. This symbol indicates that the oil has been certified by the American Petroleum Institute (API).
5-14 Service and Appearance Care When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A CHANGE ENGINE OIL SOON message comes on. Change the oil as soon as possible within the next 600 miles (1 000 km). It is possible that, if driving under the best conditions, the oil life system might not indicate that an oil change is necessary for over a year.
Service and Appearance Care If the vehicle has Driver Information Center (DIC) buttons: 1. Turn the ignition to ON/RUN, with the engine off. 2. Press the vehicle information button until OIL LIFE REMAINING displays. 3. Press and hold the set/reset button until 100% is displayed. Three chimes sound and the CHANGE ENGINE OIL SOON message goes off. 4. Turn the key to LOCK/OFF. If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the engine oil life system has not reset.
5-16 Service and Appearance Care To inspect or replace the engine air cleaner/filter: 5. Inspect or replace the air filter element. 6. Reverse Steps 1 through 3 to reinstall the cover and reconnect the electrical connector. { CAUTION 1. Loosen the screws that hold the cover on. 2. Disconnect the electrical connector. 3. Lift off the cover. 4. Remove the engine air cleaner/ filter element and any loose debris that may be found in the air cleaner base.
Service and Appearance Care The transmission fluid will not reach the end of the dipstick unless the transmission is at operating temperature. If you need to check the transmission fluid level, please take the vehicle to your dealer/retailer. Cooling System The cooling system allows the engine to maintain the correct working temperature. { CAUTION An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury.
5-18 Service and Appearance Care What to Use { CAUTION Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned.
Service and Appearance Care Checking Coolant How to Add Coolant to the Recovery Tank The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down.
5-20 Service and Appearance Care How to Add Coolant to the Radiator { CAUTION An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION (Continued) Wait for the cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap.
Service and Appearance Care 5-21 9. If the coolant level inside the radiator filler neck is low, add more of the proper DEX-COOL coolant mixture through the filler neck until the level is back up to the base of the filler neck. Replace the pressure cap. Be sure to secure it tightly. 6. Fill the coolant recovery tank to the FULL COLD mark. 7. Reinstall the cap on the coolant recovery tank but leave the radiator pressure cap off. 8. Start the engine and let it run until the upper radiator hose feels warm.
5-22 Service and Appearance Care Engine Overheating The vehicle has several indicators to warn of engine overheating. There is an engine coolant temperature gage on the instrument panel cluster. See Engine Coolant Temperature Gage on page 3-38. The vehicle may also display an ENGINE OVERHEATED IDLE ENGINE and ENGINE OVERHEATED STOP ENGINE message in the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-56.
Service and Appearance Care If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: • • • • Climbs a long hill on a hot day. Stops after high-speed driving. Idles for long periods in traffic. Tows a trailer. If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2.
5-24 Service and Appearance Care Power Steering Fluid How to Check Power Steering Fluid What to Use To check the power steering fluid: To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 6-12. Always use the proper fluid. 1. Turn the key off and let the engine compartment cool down. 2. Remove engine oil fill cap. The power steering fluid reservoir is located toward the front of the engine compartment on the passenger side of the vehicle.
Service and Appearance Care Adding Washer Fluid Notice: When the windshield washer fluid reservoir is low, a WASHER FLUID LOW ADD FLUID message will be displayed on the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-56 for more information. • When using concentrated washer fluid, follow the manufacturer’s instructions for adding water. Brakes Brake Fluid • Do not mix water with ready-to-use washer fluid.
5-26 Service and Appearance Care There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up. • A fluid leak in the brake hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well. Do not top off the brake fluid.
Service and Appearance Care Notice: Brake Wear • Using the wrong fluid can badly This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly. damage brake hydraulic system parts.
5-28 Service and Appearance Care Brake Adjustment Battery Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear. This vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. Replacing Brake System Parts The braking system on a vehicle is complex.
Service and Appearance Care Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
5-30 Service and Appearance Care Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlets. Turn off the radio and all lamps that are not needed.
Service and Appearance Care Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 5-31 7. Do not let the other end touch metal.
5-32 Service and Appearance Care To disconnect the jumper cables from both vehicles, do the following: 10. Now start the vehicle with the good battery and run the engine for a while. 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service.
Service and Appearance Care Headlamp Aiming Bulb Replacement Headlamp aim has been preset at the factory and should need no further adjustment. For the proper type of replacement bulbs, see Replacement Bulbs on page 5-34. However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (for vertical aim).
5-34 Service and Appearance Care 9. Push the taillamp assembly back into its original location. When reinstalling the taillamp assembly, make sure the pin on the taillamp assembly lines up and is inserted correctly into the opening of the vehicle. 10. Reinstall the two nuts that hold the taillamp assembly in place. 11. Reinstall the two taillamp nut covers. 3. Remove the two taillamp nut covers. 4. Remove the two nuts holding the taillamp assembly in place. 5. Pull out the taillamp assembly. 6.
Service and Appearance Care Windshield Wiper Blade Replacement Backglass Wiper Blade To replace the backglass wiper blade: Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 6-3 for more information. 1. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position so care should be used when pulling it away from the vehicle.
5-36 Service and Appearance Care Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. { CAUTION Poorly maintained and improperly used tires are dangerous. • Overloading your vehicle’s tires can cause overheating as a result of too much flexing.
Service and Appearance Care Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail.
5-38 Service and Appearance Care (B) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. Compact Spare Tire Example (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat.
Service and Appearance Care Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association. (B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall.
5-40 Service and Appearance Care Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inflation - Tire Pressure on page 5-42.
Service and Appearance Care Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-16. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle.
5-42 Service and Appearance Care Vehicle Capacity Weight: The number of designated seating positions multiplied by 150 lbs (68 kg) plus the rated cargo load. See Loading the Vehicle on page 4-16. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle’s capacity weight and the original equipment tire size and recommended inflation pressure.
Service and Appearance Care When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, if the vehicle has one. It should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 5-77. How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under-inflated.
5-44 Service and Appearance Care As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure.
Service and Appearance Care Vehicles with TPMS operate on a radio frequency and comply with RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
5-46 Service and Appearance Care A Tire and Loading Information label, attached to your vehicle, shows the size of your vehicle’s original equipment tires and the correct inflation pressure for your vehicle’s tires when they are cold. See Loading the Vehicle on page 4-16, for an example of the Tire and Loading Information label and its location on your vehicle. Also see Inflation - Tire Pressure on page 5-42. Always use the GM approved tire sealant available through your dealer/retailer.
Service and Appearance Care • One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer/ retailer for service. • Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels. Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly.
5-48 Service and Appearance Care The TPMS sensor matching process is outlined below: 1. Set the parking brake. 2. Turn the ignition switch to ON/RUN with the engine off. 3. Press the Remote Keyless Entry (RKE) transmitter’s LOCK and UNLOCK buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen. 4. Start with the driver side front tire. 5.
Service and Appearance Care Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-50 and Wheel Replacement on page 5-54. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Inflation - Tire Pressure on page 5-42 and Loading the Vehicle on page 4-16. Reset the Tire Pressure Monitor System.
5-50 Service and Appearance Care When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
Service and Appearance Care GM’s exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM’s TPC Spec number is molded onto the tire’s sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by an MS for mud and snow.
5-52 Service and Appearance Care Non-TPC Spec rated tires may give a low-pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires. See Tire Pressure Monitor System on page 5-43. Your vehicle’s original equipment tires are listed on the Tire and Loading Information Label. See Loading the Vehicle on page 4-16, for more information about the Tire and Loading Information Label and its location on your vehicle.
Service and Appearance Care The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter-type snow tires, space-saver, or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires.
5-54 Service and Appearance Care Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Service and Appearance Care Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 5-65 for more information. Used Replacement Wheels { CAUTION Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven.
5-56 Service and Appearance Care If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain the tires properly. See Tires on page 5-36. If air goes out of a tire, It is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side.
Service and Appearance Care Tire Sealant and Compressor Kit { CAUTION Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 2-30.
5-58 Service and Appearance Care This vehicle may have one of the following tire sealant and compressor kits. The kit includes: Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gage D. Pressure Deflation Button (If equipped) E. Tire Sealant Canister F. Sealant/Air Hose (Clear) G. Air Only Hose (Black) H.
Service and Appearance Care 5-59 Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inflate the tire faster. Always do a safety check first. See If a Tire Goes Flat on page 5-56. Do not remove any objects that have penetrated the tire. 1.
5-60 Service and Appearance Care 2. Unwrap the sealant/air hose (F) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the sealant/air hose (F) onto the tire valve stem. Turn it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle.
Service and Appearance Care Notice: If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 7-6. 11. Press the on/off button (B) to turn the tire sealant and compressor kit off.
5-62 Service and Appearance Care 20. Wipe off any sealant from the wheel, tire, and vehicle. 21. Dispose of the used sealant canister (E) and sealant/air hose (F) assembly at a local dealer/retailer or in accordance with local state codes and practices. 22. Replace it with a new canister available from your dealer/retailer. 23.
Service and Appearance Care 4. Remove the tire valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight. 6. Plug the power plug (H) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 3-17. If the vehicle has an accessory power outlet, do not use the cigarette lighter.
5-64 Service and Appearance Care 14. Replace the air only hose (G) and the power plug (H) and cord back in its original location. Removal and Installation of the Sealant Canister 15. Place the equipment in the original storage location in the vehicle. 1. Unwrap the sealant hose. To remove the sealant canister: 2. Press the canister release button. 3. Pull up and remove the canister. 4. Replace with a new canister which is available from your dealer/retailer. 5. Push the new canister into place.
Service and Appearance Care Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 3-5. { CAUTION Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1. Set the parking brake firmly.
5-66 Service and Appearance Care Removing the Spare Tire and Tools The tools needed to remove the spare tire are located in the storage compartment on the driver side, at the rear of the vehicle. 1. Open the jack storage compartment by pulling on the latch tab, located toward the rear of the vehicle, and pulling the cover off. 2. Remove the wing bolt (B) by turning it counterclockwise 3. Push the jack (C) up out of the holding bracket. 4. Turn the jack on its side, with the bottom facing toward you.
Service and Appearance Care 1. Open the storage compartment door of the convenience center that is nearest the liftgate and remove the cap on the bottom of the storage compartment. 5-67 6. Turn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full-size or a flat road tire under the vehicle. See Storing a Flat or Spare Tire and Tools on page 5-74. 2. Open the carpet cutout that is located through the hole of the storage compartment.
5-68 Service and Appearance Care Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2. If it is not visible, see Secondary Latch System on page 5-72. If it is visible, first try to tighten the cable by turning the lug wrench clockwise until you hear two clicks or feel it skip twice. You cannot over-tighten the cable. 3. Loosen the cable by turning the wrench counterclockwise three or four turns. 4.
Service and Appearance Care 5. Do not raise the vehicle yet. Put the compact spare tire near you. 5-69 6. Attach the lug wrench to the jack, and turn the wrench clockwise to raise the jack head 3 inches (7.6 cm). { CAUTION Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. 4. To identify the appropriate jacking location, find the triangle (A) about 12 inches (30.
5-70 Service and Appearance Care { CAUTION 9. Remove the plastic spare tire heat shield by pulling the rubber latch. Store the plastic spare tire heat shield. See Storing a Flat or Spare Tire and Tools on page 5-74 for more information. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Service and Appearance Care 12. Put the nuts on by hand by turning the clockwise until the wheel is held against the mounting surface. Make sure the rounded end is toward the wheel. 13. Lower the vehicle by attaching the lug wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. { CAUTION Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off.
5-72 Service and Appearance Care Secondary Latch System This vehicle has an underbody mounted tire hoist assembly that has a secondary latch system. It is designed to stop the compact spare tire from suddenly falling off the vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down. See Storing a Flat or Spare Tire and Tools on page 5-74 for instructions on storing the spare tire correctly.
Service and Appearance Care 9. Tilt the retainer and slip it through the wheel opening when the spare tire has been completely lowered. 5. Turn the lug wrench clockwise to raise the jack until it lifts the secondary latch spring. 6. Keep raising the jack until the spare tire stops moving upward and is held firmly in place. This lets you know that the secondary latch has released and the spare tire is balancing on the jack. 10.
5-74 Service and Appearance Care Storing a Flat or Spare Tire and Tools Storing the Spare Tire { CAUTION The underbody-mounted spare tire needs to be stored with the valve stem pointing down. If the spare tire is stored with the valve stem pointing upwards, the secondary latch will not work properly and the spare tire could loosen and suddenly fall from the vehicle. If this happened when the vehicle was being driven, the tire might contact a person or another vehicle, causing injury and damage to itself.
Service and Appearance Care 5-75 3. Put the flat tire in the rear storage area with the valve stem pointing toward the rear of the vehicle. 6. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire. If the tire moves, use the lug wrench to tighten the cable. Storing the Flat Tire 1. Remove the cable package from the jack storage area. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels. 5.
5-76 Service and Appearance Care Storing the Tools 3. Reinstall the wing bolt (B) by turning clockwise. 4. To replace the cover, line up the tab at the front of the cover with the notch in the cover opening. Push the cover in place and make sure that the rear clips are in the slots and push the cover closed. 8. Make sure the metal tube is centered at the striker. Push the tube toward the front of the vehicle. 9. Close the liftgate and make sure it is latched properly. A. Tool Bag B. Wing Bolt C.
Service and Appearance Care Compact Spare Tire { CAUTION Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time. The compact spare tire, if the vehicle has one, was fully inflated when the vehicle was new, however, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa).
5-78 Service and Appearance Care Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from the upholstery. It is important to keep the upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible.
Service and Appearance Care Do not clean the vehicle using: Fabric/Carpet • A knife or any other sharp object Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For any soil, always try to remove it first with plain water or club soda.
5-80 Service and Appearance Care Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather.
Service and Appearance Care Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 6-12. Washing Your Vehicle The best way to preserve the vehicle’s finish is to keep it clean by washing it often.
5-82 Service and Appearance Care If the vehicle has a basecoat/ clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/ clearcoat paint finish on the vehicle.
Service and Appearance Care Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride.
5-84 Service and Appearance Care Sheet Metal Damage Underbody Maintenance Chemical Paint Spotting If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Chemicals used for ice and snow removal and dust control can collect on the underbody.
Service and Appearance Care Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for the vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The eighth character in the VIN is the engine code.
5-86 Service and Appearance Care Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain the vehicle’s battery, even if the vehicle is not operating. The vehicle has an airbag system.
Service and Appearance Care Fuses AIRBAG AMP BCK/UP/ STOP BCM CNSTR/ VENT CTSY DR/LCK Fuse Side Usage Airbag Amplifier Back-up Lamp/Stoplamp Body Control Module Canister Vent Courtesy Door Locks Daytime Running DRL Lamps GMC HID DRL 2 Only/Rear Fog Lamps-China Only DSPLY Display Front Windshield FRT/WSW Washer HTD/COOL Heated/Cooling SEAT Seats Heating, Ventilation HVAC and Air Conditioning 5-87 Fuses Usage IADV/ Inadvertent PWR/LED Power LED INFOTMNT Infotainment Driver Side Turn LT/TRN/SIG Signal Mem
5-88 Service and Appearance Care Relays PWR/ WNDW PWR/ COLUMN L/GATE LCK Relay Side Relays LT/PWR/ SEAT RT/PWR/ SEAT Usage Driver Side Power Seat Relay Passenger Side Power Seat Relay Usage Power Windows Relay Power Steering Column Relay Liftgate Relay Power Lock Relay Window REAR/WSW Rear Washer Relay UNLCK Power Unlock Relay Daytime Running DRL2 Lamps 2 Relay Side Unlock LT/UNLCK Driver Relay Daytime Running DRL Lamps Relay SPARE Spare Front Windshield FRT/WSW Washer Relay Underhood Fuse Block The un
Service and Appearance Care Fuses AWD 5-89 Usage All-Wheel-Drive System BATT 1 Battery 1 BATT 2 Battery 2 BATT 3 Battery 3 ECM Engine Control Module ECM 1 Engine Control Module 1 EMISSION 1 Emission 1 EMISSION 2 Emission 2 Fuses Usage A/C CLUTCH Air Conditioning Clutch ABS MTR Antilock Braking System (ABS) Motor AFS Adaptive Forward Lighting System Fuses Usage EVEN COILS Even Injector Coils AIRBAG Airbag System FAN 1 Cooling Fan 1 AUX POWER Auxiliary Power FAN 2 Cooling Fan 2
5-90 Service and Appearance Care Fuses Usage Fuses FSCM Fuel System Control Module ODD COILS Odd Injector Coils HORN Horn PCM IGN Powertrain Control Module Ignition Windshield HTD WASH Heated Washer Fluid HTD MIR Heated Outside Rearview Mirror Usage Right Parking Lamp RT TRLR Trailer Right and Turn STOP/TRN Stoplamp Signal Voltage RVC SNSR Regulated Control Sensor PWR OUTLET Power Outlet S/ROOF/ SUNSHADE Sunroof REAR CAMERA Rear Camera LT HI BEAM Left High-Beam Headlamp RR APO Rear
Service and Appearance Care Fuses Usage TRLR BRK Trailer Brake TRLR PRK Trailer Parking LAMP Lamps TRLR PWR Trailer Power WPR/WSW Windshield Wiper/Washer Relays A/C CMPRSR CLTCH AUX VAC PUMP CRNK FAN 1 FAN 2 FAN 3 FOG LAMP HI BEAM Usage Air Conditioning Compressor Clutch Auxiliary Vacuum Pump Switched Power Cooling Fan 1 Cooling Fan 2 Cooling Fan 3 Fog Lamps High-Beam Headlamps Relays HID/LO BEAM HORN IGN LT TRLR STOP/TRN PRK LAMP PWR/TRN RR DEFOG RT TRLR STOP/TRN Stop Lamps (China Only) TRLR BCK/UP WPR
5-92 Service and Appearance Care Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Capacities English Metric For the air conditioning system refrigerant charge amount, see the refrigerant caution label located Air Conditioning Refrigerant R134a under the hood. See your dealer/retailer for more information. Cooling System 11.4 qt 10.8 L Engine Oil with Filter 5.5 qt 5.
Maintenance Schedule Maintenance Schedule Maintenance Schedule Introduction Maintenance Schedule Introduction ..........................6-1 Maintenance Requirements .....6-1 Your Vehicle and the Environment ........................6-1 Using the Maintenance Schedule ............................6-2 Scheduled Maintenance .........6-3 Additional Required Services ...6-6 Maintenance Footnotes ..........6-7 Owner Checks and Services ...6-9 At Each Fuel Fill ...................6-9 At Least Once a Month .......
6-2 Maintenance Schedule Improper fluid levels or the wrong tire inflation can increase the level of emissions from the vehicle. To help protect the environment, and to keep the vehicle in good condition, be sure to maintain the vehicle properly. Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week.
Maintenance Schedule To purchase service information, see Service Publications Ordering Information on page 7-15. Owner Checks and Services on page 6-9 tells what should be checked, when to check it, and what can easily be done to help keep the vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Maintenance Replacement Parts on page 6-14. When the vehicle is serviced, make sure these are used.
6-4 Maintenance Schedule Maintenance I — Use Maintenance I if the CHANGE ENGINE OIL SOON message displays within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message displays 10 months or more since the last service or if the message has not come on at all for one year.
Maintenance Schedule 6-5 Scheduled Maintenance (cont’d) Service Maintenance I Maintenance II Inspect brake system. See footnote (a). • • Check engine coolant and windshield washer fluid levels and add fluid as needed. • • Perform any needed additional services. See “Additional Required Services” in this section. • • Inspect suspension and steering components. See footnote (b). • Inspect engine cooling system. See footnote (c). • Inspect wiper blades. See footnote (d).
6-6 Maintenance Schedule Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Additional Required Services Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect fuel system for damage or leaks. • • • • • • Inspect exhaust system for loose or damaged components.
Maintenance Schedule 6-7 Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). • Inspect engine accessory drive belt. An Emission Control Service. See footnote (k).
6-8 Maintenance Schedule (e) Make sure the safety belt reminder light and safety belt assemblies are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also see Checking the Restraint Systems on page 1-59.
Maintenance Schedule Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure vehicle safety, dependability, and emission control performance. Your dealer/ retailer can assist with these checks and services. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to the vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 6-12.
6-10 Maintenance Schedule At Least Once a Year Starter Switch Check { CAUTION When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. Automatic Transmission Shift Lock Control System Check { CAUTION When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 1.
Maintenance Schedule Parking Brake and Automatic Transmission P (Park) Mechanism Check { CAUTION When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.
6-12 Maintenance Schedule Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Engine Oil Engine Coolant Hydraulic Brake System Windshield Washer Power Steering System Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Maintenance Schedule Usage Automatic Transmission Key Lock Cylinders Fluid/Lubricant ® DEXRON -VI Automatic Transmission Fluid. Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Carrier Assembly — Differential (Rear Drive Module) and Transfer Case (Power Transfer Unit) SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677 in Canada 89021678) meeting GM Specification 9986115.
6-14 Maintenance Schedule Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter Engine Oil Filter Spark Plugs Wiper Blades Front Driver – 24.6 in (62.5 cm) Front Passenger – 20.8 in (53.0 cm) Rear – 11.6 in (30.
Maintenance Schedule Engine Drive Belt Routing 3.
6-16 Maintenance Schedule Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-1. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Maintenance Schedule Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-17
6-18 Maintenance Schedule Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed
Customer Assistance Information Customer Assistance Information Customer Assistance and Information Customer Satisfaction Procedure ...........................7-1 Online Owner Center .............7-3 Customer Assistance for Text Telephone (TTY) Users .................................7-4 Customer Assistance Offices ...7-5 GM Mobility Reimbursement Program .............................7-6 Roadside Assistance Program .............................7-6 Scheduling Service Appointments ......................
7-2 Customer Assistance Information STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the U.S., call the Chevrolet Customer Assistance Center at 1-800-222-1020. In Canada, call General Motors of Canada Customer Communication Centre at 1-800-263-3777 (English), or 1-800-263-7854 (French). We encourage you to call the toll-free number in order to give your inquiry prompt attention.
Customer Assistance Information STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program. General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims.
7-4 Customer Assistance Information Chevrolet — www.chevrolet.com Here are a few of the valuable tools and services you will have access to: Chevrolet Merchandise — www.chevymall.com • My Showroom: Find and save Other Helpful Links: Help Center — www.chevrolet.com/ helpcenter • FAQ • Contact Us My GM Canada (Canada) — www.gm.ca My GM Canada is a password-protected section of www.gm.
Customer Assistance Information Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O. Box 33170 Detroit, MI 48232-5170 Chevrolet.
7-6 Customer Assistance Information GM Mobility Reimbursement Program General Motors of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830.
Customer Assistance Information Coverage Services are provided up to 5 years/ 100,000 miles (160 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered. In Canada, a person driving the vehicle without permission from the owner is not covered. Roadside Assistance is not a part of the New Vehicle Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notification.
7-8 Customer Assistance Information Services Not Included in Roadside Assistance • Impound towing caused by violation of any laws. • Legal fines. • Mounting, dismounting or changing of snow tires, chains, or other traction devices. • Towing or services for vehicles driven on a non-public road or highway. Services Specific to Canadian Purchased Vehicles • Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted.
Customer Assistance Information If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related. If it is, please call your dealership/retailer, let them know this, and ask for instructions. If the dealer/retailer requests you to bring the vehicle for service, you are urged to do so as early in the work day as possible to allow for the same day repair.
7-10 Customer Assistance Information Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair. Rental reimbursement will be limited and must be supported by original receipts. This requires that you sign and complete a rental agreement and meet state/provincial, local, and rental vehicle provider requirements.
Customer Assistance Information Recycled original equipment parts may also be used for repair. These parts are typically removed from vehicles that were total losses in prior crashes. In most cases, the parts being recycled are from undamaged sections of the vehicle. A recycled original equipment GM part, may be an acceptable choice to maintain your vehicle’s originally designed appearance and safety performance, however, the history of these parts is not known.
7-12 Customer Assistance Information If a Crash Occurs Here is what to do if you are involved in a crash. • Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. • If there has been an injury, call emergency services for help. Do not leave the scene of a crash until all matters have been taken care of. Move your vehicle only if its position puts you in danger or you are instructed to move it by a police officer.
Customer Assistance Information • Choose a reputable collision repair facility for your vehicle. Whether you select a dealer/ retailer or a private collision repair facility to fix the damage, make sure you are comfortable with them. Remember, you will have to feel comfortable with their work for a long time. • Once you have an estimate, read it carefully and make sure you understand what work will be performed on your vehicle. If you have a question, ask for an explanation.
7-14 Customer Assistance Information Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying General Motors.
Customer Assistance Information 7-15 Service Publications Ordering Information The owner manual includes the Maintenance Schedule for all models. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time Service Manuals In-Portfolio: Includes a Portfolio, Owner Manual, and Warranty Booklet. For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc. on the World Wide Web at: helminc.
7-16 Customer Assistance Information Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
Customer Assistance Information GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office; as part of GM’s defense of litigation through the discovery process; or, as required by law.
7-18 Customer Assistance Information ✍ NOTES
INDEX A Accessories and Modifications ...................... 5-3 Accessory Power ................. 2-22 Accessory Power Outlets ...... 3-17 Adding Equipment to Your Airbag-Equipped Vehicle .... 1-58 Additional Required Services, Scheduled Maintenance ....... 6-6 Additives, Fuel ...................... 5-5 Add-On Electrical Equipment ....................... 5-86 Air Cleaner/Filter, Engine ....... 5-15 Air Conditioning ................... 3-19 Airbag Readiness Light ................ 3-33 Airbag System .......
i-2 INDEX B C Battery ............................... 5-28 Electric Power Management ................. 3-15 Run-Down Protection ......... 3-16 Belt Routing, Engine ............. 6-15 Blind Spot Mirrors ................ 2-34 Bluetooth® ......................... 3-103 Brake Emergencies ...................... 4-5 Brake Fluid ......................... 5-25 Brakes ............................... 5-25 Antilock ............................. 4-4 Parking ........................... 2-27 System Warning Light ....
INDEX Cleaning (cont.) Instrument Panel, Vinyl, and Other Plastic Surfaces ...................... Interior ............................ Leather ........................... Tires ............................... Underbody Maintenance .... Washing Your Vehicle ........ Weatherstrips ................... Windshield, Backglass, and Wiper Blades .......... Climate Control System ......... Outlet Adjustment ............. Rear Air Conditioning and Heating System .............
i-4 INDEX Driver Seat Height Adjuster ........... 1-3 Driver Information Center (DIC) .................... 3-44 DIC Operation and Displays ............... 3-45, 3-51 DIC Vehicle Customization ............... 3-65 DIC Warnings and Messages .................... 3-56 Driving At Night .......................... 4-10 Before a Long Trip ............ 4-12 Defensive .......................... 4-2 Drunk ............................... 4-2 Highway Hypnosis ............ 4-13 Hill and Mountain Roads ....
INDEX F Filter Engine Air Cleaner ............ 5-15 Finish Damage .................... 5-84 Flashers, Hazard Warning ....... 3-5 Flash-to-Pass ........................ 3-7 Flat Tire .............................. 5-56 Flat Tire, Changing ............... 5-65 Flat Tire, Storing .................. 5-74 Floor Mats .......................... 2-54 Fluid Automatic Transmission ..... 5-16 Power Steering ................. 5-24 Windshield Washer ........... 5-24 Fog Lamp Fog ................................
i-6 INDEX Hood Checking Things Under ....... 5-9 Release ............................ 5-9 Horn .................................... 3-5 How to Wear Safety Belts Properly .......................... 1-17 I Ignition Positions .................. 2-21 Infants and Young Children, Restraints ........................ 1-29 Inflation - Tire Pressure ......... 5-42 Instrument Panel Brightness ....................... 3-13 Cluster ............................ 3-31 Overview ...........................
INDEX Locks (cont.) Power Door ....................... 2-8 Programmable Automatic Door Locks .................... 2-9 Rear Door Security Locks .... 2-9 Loss of Control .................... 4-10 Lower Anchors and Tethers for Children ...................... 1-35 Luggage Carrier ................... 2-54 Lumbar Manual Controls ................. 1-4 Power Controls .................. 1-5 M Maintenance Footnotes .......................... 6-7 Maintenance Schedule Additional Required Services .....................
i-8 INDEX Outside Convex Mirror .................. 2-35 Heated Mirrors ................. 2-35 Power Foldaway Mirrors .... 2-33 Power Mirrors .................. 2-32 Overheated Engine Protection Operating Mode ................ 5-23 Owner Checks and Services .... 6-9 Owners, Canadian .................... ii P Paint, Damage ..................... 5-84 Parade Dimming .................. 3-15 Park Shifting Into ..................... 2-28 Shifting Out of .................. 2-29 Park Aid .........................
INDEX Rearview Mirror, Automatic Dimming .......................... 2-31 Rearview Mirrors .................. 2-31 Reclining Seatbacks ............... 1-8 Recommended Fluids and Lubricants ........................ 6-12 Recreational Vehicle Towing ... 4-21 Reimbursement Program, GM Mobility ....................... 7-6 Remote Keyless Entry (RKE) System ............................. 2-3 Remote Keyless Entry (RKE) System, Operation .............. 2-4 Remote Vehicle Start .............
i-10 INDEX Secondary Latch System ....... 5-72 Securing a Child Restraint Rear Seat Position ............ 1-41 Right Front Seat Position ... 1-43 Security Light ...................... 3-43 Service ................................ 5-3 Accessories and Modifications .................. 5-3 Adding Equipment to the Outside of the Vehicle ..... 5-4 Doing Your Own Work ........ 5-4 Engine Soon Lamp ........... 3-39 Publications Ordering Information ................... 7-15 Scheduling Appointments .....
INDEX Tire Sealant and Compressor Kit ................ Tires .................................. Aluminum or Chrome-Plated Wheels, Cleaning ...................... Buying New Tires ............. Chains ............................ Changing a Flat Tire ......... Cleaning .......................... Compact Spare ................ Different Size ................... If a Tire Goes Flat ............ Inflation - Tire Pressure ..... Inspection and Rotation ..... Installing the Spare Tire .....
i-12 INDEX Ventilation Adjustment ........... Visors ................................. Voltage Devices, and Wiring ... Voltmeter Gage .................... 3-27 2-16 5-85 3-35 W Warning Lights, Gages, and Indicators ........................ 3-30 Warnings DIC Warnings and Messages .................... 3-56 Hazard Warning Flashers .... 3-5 Safety and Symbols .............. iii Wheels Alignment and Tire Balance ................. 5-54 Different Size ................... 5-52 Replacement ....................
