Oscillating Multi-Function Power Tool 68303 Oscillating Multi-Function Tool Read this material before using this product. Failure to do so can result in serious injury. Save this manual. When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-800-444-3353 as soon as possible. Visit our website at: http://www.harborfreight.com Copyright© 2010 by Harbor Freight Tools®. All rights reserved.
Specifications Electrical Input 120 V~ / 60 Hz / 1.8 A No Load Speed 21,000 OPM Spindle 1-1/6” Accessories Included 1 Angled Cutter 1 Hex Wrench CAUTION, without the safety alert symbol, is used to address practices not related to personal injury. General Power Tool Safety Warnings Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures.
Interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock. 3. Personal Safety a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b. Use personal protective equipment. Always wear eye protection.
Fault Circuit Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock. 9. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm.
2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Extension Cords 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord.
Instructions for Putting into Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before assembling or making any adjustments to the tool.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before adjusting tool or installing accessories. Assembly 1. Turn the Power Switch off and unplug the tool. 2.
General Operating Instructions TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before adjusting tool or installing accessories. 1. With the tool unplugged, mount the attachment in place. 2. Pull the Power Switch back to its off position. Then plug the Power Cord into the nearest 120 volt, grounded electrical outlet. 3. To turn on the tool, slide the Power Switch forward. 4.
Troubleshooting Problem Tool will not start. Possible Causes 1. Cord not connected. 2. No power at outlet. Likely Solutions 1. Check that cord is plugged in. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. 3. Have technician service tool. 3. Internal damage or wear. (Carbon brushes or switch, for example.) Attachment is 1. Holes on attachment not lined up 1.
Parts List and Assembly Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Parts List and Assembly Diagram Assembly Diagram 13 14 15 17 12 16 19 18 20 11 21 23 10 22 24 9 25 8 26 27 7 24 6 31 5 4 47 29 32 33 37 40 3 2 36 38 44 39 48 49 45 46 1 42 43 41 SKU 68303 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.