DESKTOP MAGNIFYING LAMP Model 97448 Assembly And Operation Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual.
NOTICE is used to address practices not related to personal injury. Save This Manual Notice Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
2. Unplug from outlet when not in use and before maintenance or cleaning. 3. Do not operate with a damaged cord or plug or after the Lamp malfunctions or has been damaged in any manner. Return Lamp to the nearest authorized service facility for examination, or repair. 4. 5. This Lamp has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way.
Specifications Electrical Requirements 120 V~ / 60 Hz Material ABS plastic frame Glass lens Magnification 3 D + 12 D Bulb Type 4T 12W Energy Saving Compact Fluorescent Lamp Cord Length 4’ - 9” Height 20” Base Dimensions 8-5/16” L x 4-1/4” W Power Switch E224011 Figure A Unpacking 2. When unpacking, check to make sure that the item is intact and undamaged.
6. NOT attached to the Frame and may pop out. Store Lamp in a safe location out of the reach of children. REPLACING THE BULB When replacing the Lamp Bulb (5), be sure to wear ANSIapproved safety goggles. Also, keep track of the Screws (8) during replacement. The Screws are very small and can be swallowed by young children. 1. 2. Bulb To replace the Bulb (5), turn off the Lamp and unplug the Power Cord (13) from the outlet.
INSPECTION and MAINTENANCE Glass Frame To prevent serious injury from accidental operation or electric shock: Before appliance inspection or maintenance, make sure the Power Switch (12) is turned off, the cord is unplugged, and the bulb has cooled. WARNING Bulb Bulb Support Latch Figure F 8. 9. Fasten the Bulb Support Latch back into place. See Figure F, above. To prevent serious injury from Appliance failure: Do not use damaged Lamp. Have the problem corrected before further use.
PARTS LIST AND ASSEMBLY DIAGRAM Lens Cover (3) not shown 2 5 Part Description 1 Q’ty 1 Lens 1 2 Lens Frame 1 3 Lens Cover 1 4 Glass Frame 1 5 Bulb 1 6 Bulb Support Latch 1 7 Bulb Socket 1 8 Screws 5 9 Adjusting Knobs 2 10 Arm 1 11 Base 1 12 Power Switch 1 13 Power Cord 1 8 6 4 7 8 8 9 10 9 12 11 13 PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool on
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
LAMPE DE BUREAU GROSSISSANT Modèle 97448 Les instructions de montage et d’opération IMPORTANT! Cette édition de langue française est une traduction du manuel anglais original accompagnant ce produit. Si une partie du manuel anglais original est inconsistante avec cette traduction, le manuel anglais original gouvernera. Distribué exclusivement par le Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visitez notre site Internet à: http://www.harborfreight.
Sauvez Ce Manuel L’ATTENTION, utilisée avec le symbole d’alerte de sécurité, indique une situation la hasardeuse qui, si non évité, pourrait s’ensuivre dans le mineur ou modérer la blessure. Gardez ce manuel pour les avertissements de sécurité et les précautions, le montage, le fait de faire marcher, l’inspection, la maintenance et le nettoyage des procédures.
2. Une surveillance étroite est nécessaire lorsque utilisé par ou près d’enfant. 3. Ne laissez pas le cordon d’alimentation pendre le long d’une table ou d’un comptoir ni toucher une surface chaude. 4. Ne le placez pas sur ou près d’un brûleur à gaz, d’un élément électrique ou dans un four chaud. 5. Faites preuve d’une extrême prudence lorsque vous déplacez La Lampe. 6. Assurez-vous que l’espace de travail est bien éclairé.
2. L’utilisation d’accessoires non recommandés par le fabricant risque d’occasionner des blessures. 3. Ne placez pas sous le soleil direct. 4. N’utilisez pas La Lampe pour des applications différentes de celle pour laquelle elle a été conçue. 5. Entretenez les étiquettes et plaques signalétique qui paraissent sur la Lampe. Des informations importantes y paraissent. S’il manque de l’information ou si les informations sont mal écrites, communiquez avec Harbor Freight Tools pour faire remplacer l’unité.
Caractéristiques Puissance Nécessaire Matériau 120 V ~ / 60 Hz Cadre en plastique ABS Lentille en verre Grossissement 3 D + 12 D Type d’Ampoule Économie d’Énergie à 4 T et 12 W Lampe Fluorescent Concis Longueur du 4 pieds – 9 p o Cordon Hauteur 20 p o Dimensions de 8-5/16 p o L x 4-1/4 p o W La Base Interrupteur E244011 DÉBALLER Image A 2. En déballant, vérifiez pour vous assurer que l’article est intact et non endommagé.
(8) du Cadre en verre (4). Voir L’Image C, au-dessus. branchez Le Cordon d’Alimentation (13) de La Prise de courant. 6. Rangez La Lampe dans un endroit sécuritaire hors de la portée des enfants. 4. REMPLACER L’AMPOULE Lorsque vous remplacez L’Ampoule de La Lampe (5), assurez-vous de porter des lunettes protectrices approuvées par ANSI. Conservez aussi un suivi des vis (8) lors du remplacement. Les vis sont très petites et peut être avalé par les jeunes enfants. 1. 2.
7. Disposez correctement La Vieux Ampoule et attachez des nouvelles Ampoules à Économie d’Énergie à 4 T et12 W à La Douille d’Ampoule (7). INSPÉCTION ET ENTRETIEN POUR ÉVITER DES BLESSURE GRAVES DU FONCTIONNEMENT ACCIDENTEL OU DE CHOC ÉLECTRIQUE: Avant de l’inspection ou de l’entretien, assurez-vous que L’Interrupteur (12) est fermé, le cordon est débranché, et l’ampoule est refroidie.
LISTE DE PIÈCE ET SCHÈMA DU PRODUIT Couvercle de La Lentille (3) pas montré 2 Pièce 1 2 3 4 5 6 7 8 9 10 11 12 13 Description Lentille Cadre de La Lentille Couvercle de La Lentille Cadre en verre Ampoule Loquet du Support de L’Ampoule Douille d’Ampoule Vis Vis de Réglage Bras Base Interrupteur Cordon d’Alimentation 1 1 1 1 1 5 1 Q’ty 8 6 4 7 8 8 1 1 5 2 1 1 1 1 9 10 9 12 11 13 Garantie Déférez au texte anglais pour l’explication de garantie. 3491 Mission Oaks Blvd.