TM Owner’s Manual 1
Chicago Gaming Company, 4616 W. 19th Street, Cicero, IL 60804 (708)780-0070 ULTIMATE ARCADE TM 1. LEGAL INFORMATION 1.1 IMPORTANT SAFETY INSTRUCTIONS The following safety instructions apply to all game owners. We recommend that you read this page before setting-up Ultimate Arcade. Use the following safety guidelines to help protect the system from potential damage and to ensure your personal safety.
1.4 ATARI END USER LICENSE AGREEMENT By accepting and operating an Ultimate Arcade, the owner (“End User”) of the unit agrees to abide by the terms of this agreement. Asteroids, Asteroids Deluxe, Battlezone, Black Widow, Centipede, Crystal Castles, Gravitar, Liberator, Lunar Lander, Major Havoc, Millipede, Missile Command, Red Baron, Space Duel, Super Break-Out, Tempest, Warlords and related logos are used under license from Atari Interactive, Inc. (“Atari”).
3. ARCADE SETUP MENU Press the test button which is located behind the faux coin-door to access the ARCADE SETUP MENU. The test button can be accessed without opening the faux coin-door by pressing the coin-return button. If you want to limit access to the TEST button, open the faux coin door and control panel, loosen the nut on the back of the TEST button and move it to the left. Be sure to retighten the nut. To choose a menu option, move the arrow or cursor so that the desired option is highlighted.
3.3 GAME CONFIGURATION This menu allows you to choose which games you wish to display on the main interface selection screen and to set the dipswitch settings for each game.
3.4 DIAGNOSTICS 3.4.1 CONTROL TEST This test is used to check the functionality of the player controls. Operate each player control in turn. Each button press or joystick direction will light when activated. If any controls are not functioning, go to the trouble shooting section. To exit the control test press both player one and player two start buttons. If one or both start buttons are not working the control test screen will automatically timeout in fifteen seconds. 3.4.
and pin cushion. 3.5 CABINET SETUP 3.5.1 RESET FACTORY DEFAULTS This switch returns all settings to the default state prior to the consumer adjustments. 3.5.2 CABINET TYPE Use Upright for stand up game, and Cocktail for sit down cocktail table configurations. 3.5.3 SOUND OUTPUT Stereo setting produces different sound output from each speaker and Mono produces same sound output from each speaker. Both speakers are used in each setting. 3.5.
3.5.8 DEMONSTRATION MENU 3.5.8.1 ATTRACT MODE SOUND This option allows you to turn the Attract Mode Volume on or off. When set to “ON” all attract mode sounds will play. When set to “OFF” the full screen and windowed game attract mode sounds will not play. To change the values of this option highlight Attract Mode Volume on the Cabinet Configuration Menu (Fig. 3-10) move the joystick left or right. Note: Some games naturally do not play any sound while in attract mode. 3.5.8.
4. PLAYING A GAME 4.1 SELECT GAME INTERFACE Use the Joystick up and down to highlight a game to play and then press the player 1 start button for a single player game. Press the 2 player start button to start a 2 player game. Some games are simultaneous 2 player games while others are turn based. 4.2 INSTRUCTION SCREEN The How to Play screen shows a very basic control layout and illustrates what controls perform which actions for the started game.
4.3 EXIT GAME SCREEN The “Exit Game?” screen comes up whenever the player presses the exit game button. If YES is chosen the user will return to the main game select menu. If NO is chosen then the user will return to the game that was interrupted. 5. TROUBLESHOOTING 5.
The Ultimate Arcade Operating System comes pre-installed but if for any reason you need to reinstall your Ultimate Arcade system software, follow the steps below: 1. Open the cabinet and insert the Ultimate Arcade System CD into the CD-ROM drive. 2. Turn the Cabinet Off, wait 5 seconds and then turn the cabinet back ON. When the cabinet reboots you will see the Install menu. 3.
7.
