Safety and operating instructions Petrol breakers Valid for United States of America only CP Red Hawk www.cp.
CP Red Hawk 2 9800 0996 93 | Original instructions
CP Red Hawk Contents Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 About the Safety and operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety signal words. . . . . . . . . . . . . . . .
Safety and operating instructions 4 CP Red Hawk 9800 0996 93 | Original instructions
CP Red Hawk Safety and operating instructions Introduction Thank you for choosing Chicago Pneumatic-brand products. For over a century, the Chicago Pneumatic brand has represented performance and innovation in the pneumatic tool industry. Today the brand is found around the world on a range of pneumatic and hydraulic tools that includes breakers, rock drills, chipping hammers, clay-diggers, picks and busters, scabblers, pumps and a whole lot more.
Safety and operating instructions Safety instructions To reduce the risk of serious injury or death to yourself or others, read and understand the Safety and operating instruction before installing, operating, repairing, maintaining, or changing accessories on the machine. Post this Safety and operating instruction at work locations, provide copies to employees, and make sure that everyone reads the Safety and operating instruction before operating or servicing the machine.
CP Red Hawk Safety and operating instructions Operation, precautions ► Consumed petrol and oil containers must be taken care of and returned to the retailer. DANGER Explosion hazard If a warm insertion tool or exhaust pipe comes into contact with explosives, an explosion could occur. During operating with certain materials, sparks and ignition can occur. Explosions will lead to severe injuries or death. ► Never operate the machine in any explosive environment.
Safety and operating instructions WARNING Dust and fume hazard Dusts and/or fumes generated or dispersed when using the machine may cause serious and permanent respiratory disease, illness, or other bodily injury (for example, silicosis or other irreversible lung disease that can be fatal, cancer, birth defects, and/or skin inflammation).
CP Red Hawk Safety and operating instructions WARNING Dust hazard Some dusts, fumes or other airborne material created during use of the machine may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of such chemicals are: > Crystalline silica, cement, and other masonry products.
Safety and operating instructions WARNING Vibration hazards Normal and proper use of the machine exposes the operator to vibration. Regular and frequent exposure to vibration may cause, contribute to, or aggravate injury or disorders to the operator’s fingers, hands, wrists, arms, shoulders and/or nerves and blood supply or other body parts, including debilitating and/or permanent injuries or disorders that may develop gradually over periods of weeks, months, or years.
CP Red Hawk WARNING Noise hazard High noise levels can cause permanent and disabling hearing loss and other problems such as tinnitus (ringing, buzzing, whistling or humming in the ears). To reduce risk and prevent an unnecessary increase in noise levels: ► Risk assessment of these hazards and implementation of appropriate controls is essential. ► Operate and maintain the machine as recommended in these instructions.
Safety and operating instructions Overview CP Red Hawk Main parts To reduce the risk of serious injury or death to yourself or others, read the Safety instructions section found on the previous pages of this manual before operating the machine. Design and function CP Red Hawk is a hammering machine. It is equipped to be used for breaking asphalt and concrete. Equipped with the right accessories, the machine can also be used for driving posts, fences, and ground sampling.
CP Red Hawk Labels Safety and operating instructions Noise level label The machine is fitted with labels containing important information about personal safety and machine maintenance. The labels shall be in such condition that they are easy to read. New labels can be ordered from the spare parts list. The label indicates the guaranteed noise level corresponding to EC-directive 2000/14/EC. See "Technical data" for accurate noise level. Warning label Data plate A. Machine type B. Serial number C.
Safety and operating instructions Emissions compliance period referred to on the label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours. Transport WARNING Fuel hazard ► Empty the tank before transport. CP Red Hawk ► Avoid spilling fuel and wipe off any fuel spilled on the machine. Filling procedure 1. Stop the engine and let it cool down before filling the tank. 2.
CP Red Hawk NOTICE Never cool a hot insertion tool in water, it can result in brittleness and early failure. Checking for wear on the tool shank Safety and operating instructions WARNING Vibration hazard Using inserted tools that do not fulfil the criterias mentioned below, will result in a longer time to complete a task, and may result in higher levels of vibration exposure. A worn tool will also cause increased working time.
Safety and operating instructions Start and stop Cold start CP Red Hawk Stopping 1. Stop the machine by sliding the stop button on the left handle forward. 1. Close the choke by turning the choke control anticlockwise to position (CHOKE). Operating 2. Push the throttle lever down and pull the starter handle. Starting a cut ♦ Stand in a stable position with your feet well away from the inserted tool. ♦ Press the machine against the working surface before you start.
CP Red Hawk Maintenance Safety and operating instructions Tool chuck check Regular maintenance is a basic requirement for the continued safe and efficient use of the machine. Follow the maintenance instructions carefully. ♦ Before starting maintenance on the machine, clean it in order to avoid exposure to hazard substances. See “Dust and fume hazards” ♦ Use only authorised parts. Any damage or malfunction caused by the use of unauthorised parts is not covered by warranty or product liability.
Safety and operating instructions 1. Pull the starting handle until the arrow in the centre of the flywheel (which can be seen through the fan cover) points upwards. This indicates that the engine piston is in the upper position. CP Red Hawk Spark plug check 1. Lift the spark plug cover by the lower lip, and turn it up to one side. 2. Unscrew the gas duct valve (A) and take out the cleaning rod (B). 3. Clean the gas duct valve (A) and cleaning rod (B) using the cleaning needle (C) provided. 2.
CP Red Hawk When loaded, the maximum revs should be 2550–2700 rpm. The idling revs should be 1600–1800 rpm. Safety and operating instructions Removing the old starter cord 1. Remove the screw-cap of the PTO and the three bolts from the protective cover of the starting mechanism. Every year Overhauling should be done after 1 year of continuous operation. Overhauling should for safety reasons be performed by authorised personnel at an authorised workshop.
Safety and operating instructions 7. Pre-tension the starting spring by one turn (clockwise) before fitting the assembly into place. 8. Pull the starting handle carefully, in order to locate the cover correctly. CP Red Hawk Before a petrol driven machine is deposited it must be emptied and cleaned of all oil and petrol. Remaining oil and petrol must be dealt with in a way that does not affect the environment. 9. Fit and tighten the hexagonal bolts and the PTO screw-cap.
CP Red Hawk Safety and operating instructions Technical data Products Description Tool shank size, in. (mm) Part number CP Red Hawk ⅞ x 4¼ (22 X 108) 8318 0900 00 Machine data CP Red Hawk Type 1 cylinder, two-stroke, air cooled Cylinder displacement, ci (cc) 11.3 (185) Power kw (hp) 2.0 (2.
Safety and operating instructions CP Red Hawk We, Atlas Copco Construction Tools AB, cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. This tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at http://www.humanvibration.com/EU/VIBGUIDE.
CP Red Hawk Safety and operating instructions EC Declaration of Conformity EC Declaration of Conformity (EC Directive 2006/42/EC) We, Atlas Copco Construction Tools AB, hereby declare that the machines listed below conform to the provisions of EC Directive 2006/42/EC (Machinery Directive) and 2000/14/EC (Noise Directive), and the harmonised standards mentioned below.
Safety and operating instructions CP Red Hawk Warranty This warranty only applies in the United States of America.
CP Red Hawk Safety and operating instructions (into which the engine is incorporated) to the nearest Atlas Copco Representative as soon as a warrantable condition exists under this Emission Control System Warranty. At the time of requesting warranty repair, you must provide proof of the initial purchase of the machine, including the initial purchase date.
CP Red Hawk 26 9800 0996 93 | Original instructions
CP Red Hawk 9800 0996 93 | Original instructions 27
2010-01 | No.