Valve terminals MPA-L
Valve terminals MPA-L Key features Innovative Compact, high-performance valves in a sturdy metal housing Flow rates up to 870 l/min Wide range of electrical connection options for multi-pin plug: Sub-D, flat cable or terminal strip Connection to the electrical peripherals CPX with a wide range of communication options I-Port/IO-Link interface Freely configurable push-in connectors 2 Versatile Modular system offering a range of configuration options Freely extendable system with individual
Valve terminals MPA-L Key features Reliable operation: Non-detenting/detenting or covered manual override Width 10 mm, 14 mm and 20 mm Reduced downtimes: LED switching status display Adaptable: Selector in the end plate for defining the pilot air supply (internal or external) Pneumatic interface to CPX CPX diagnostic interface for handheld devices Space-saving: Slim valves and flat plate silencers Simple electrical connections – Multi-pin plug, fieldbus connections – Control block, CPX – I-Port interfa
Valve terminals MPA-L Key features Individual connection Valves on individual sub-bases can also be used for actuators further away from the valve terminal. The valves are screwed to an individual sub-base made from die-cast alu minium. The electrical connection is estab lished using a standard 4-pin M8 plug (EN 60947-5-2).
Valve terminals MPA-L Key features Fieldbus connection via the CPX system An integrated fieldbus node manages communication with a higher-order PLC. This enables a space-saving pneumatic and electronic solution. Valve terminals with fieldbus interfaces can be configured with up to 32 sub-bases. The CPX terminal also enables the integration of digital and analogue electrical inputs and outputs, pressure sensors and controllers for pneumatic or electric positioning axes.
Valve terminals MPA-L Peripherals overview Modular pneumatic components The modular design of the MPA-L facilitates maximum flexibility right from the planning stage and offers maximum ease of servicing during operation. The system consists of sub-bases and valves. The sub-bases form the support system for the valves. They contain the connection ducts for supplying compressed air to and venting from the valve terminal as well as the working lines for the pneumatic drives for each valve.
Valve terminals MPA-L Peripherals overview Individual sub-base Ordering: Using individual part numbers Individual sub-bases can be equipped with any valve (VMPA… of the corresponding width). The electrical connection is estab lished using a standard 4-pin M8 plug (EN 60947-5-2).
Valve terminals MPA-L Peripherals overview Valve terminal – pneumatic components The sub-bases are available individually with one valve position or with four valve positions. Double solenoid valve positions can be fitted with any valve or a blanking plate. The electrical interlinking modules are available for: 1 or 4 single solenoid valves 1 or 4 double solenoid valves 8 6 7 Single solenoid valve positions can only be fitted with single solenoid valves or a blanking plate.
Valve terminals MPA-L Peripherals overview Valve terminal – pneumatic components Designation 1 2 3 4 5 6 Plate Plate Cartridge fitting Cover cap for manual override Solenoid valve Electrical interlinking module, 4-way 7 8 9 aJ aA aB aC aD aE aF aG aH aI bJ bA bB bC bD bE bF Mounting bracket Regulator plate Pressure gauge Right-hand end plate, low Screw Right-hand end plate, high Inscription label Holder for inscription label Sub-base Sleeve Tie rod extender Tie rod Cartridge fitting Sub-base, individual
Valve terminals MPA-L Peripherals overview Valve terminal with multi-pin plug connection Order code: 34P-… MPA-L valve terminals with multi-pin plug connection can be expanded by up to 32 solenoid coils/valve positions. The multi-pin plug connection is removable and designed as a 9, 25 or 44-pin Sub-D connection. The multi-pin plug connection can alternatively be ordered as a terminal strip (33-pin) or flat cable connection (40-pin).
Valve terminals MPA-L Peripherals overview Valve terminal with fieldbus connection, control block (electrical peripherals CPX) Order code: 34P-… for the pneumatic components 50E-… for the electrical peripherals Valve terminals with CPX interface can be expanded by up to 32 solenoid coils/valve positions. Up to 32 valve positions can be equipped in combination with single solenoid valves; the maximum number of valve positions is reduced to 16 if only double solenoid valves are used.
Valve terminals MPA-L Peripherals overview Valve terminal with I-Port interface/IO-Link (and fieldbus node) Order code: 34P-… for the pneumatic components CTEU-… for the fieldbus node 1 2 Valve terminals with I-Port interface/IO-Link can be expanded by up to 32 solenoid coils/valve positions. Up to 32 valve positions can be equipped in combination with single solenoid valves. 3 The maximum number of valve positions is reduced to 16 if only double solenoid valves are used.
Valve terminals MPA-L Key features – Pneumatic components Sub-base valve MPA-L offers a comprehensive range of valve functions. All valves are equipped with piston spool and patented sealing system that facilitates efficient sealing, a broad pressure range and long service life. They have a pneumatic pilot control for optimising performance. Air is supplied by means of pilot air supply. Sub-base valves can be quickly replaced since the tubing connectors remain on the sub-base.
Valve terminals MPA-L Key features – Pneumatic components 2x 3/2-way valve Circuit symbol 14 Code Description Position function 1-32: N Single solenoid Normally open Pneumatic spring return Operating pressure 3 … 10 bar Available in width 10 mm, 14 mm and 20 mm Position function 1-32: NS Single solenoid Normally open Mechanical spring return Reversible Operating pressure –0.
Valve terminals MPA-L Key features – Pneumatic components 5/3-way valve Circuit symbol 1) Code Description Position function 1-32: B Mid-position pressurised1) Mechanical spring return Reversible Operating pressure –0.9 … +10 bar Available in width 10 mm, 14 mm and 20 mm Position function 1-32: G Mid-position closed1) Mechanical spring return Reversible Operating pressure –0.
Valve terminals MPA-L Key features – Pneumatic components Blanking plate Blanking plate (code L) without valve function, for reserving valve positions on a valve terminal. Valves and blanking plates are attached to the sub-base using two screws. The fixed restrictor can be used to permanently set the flow rate when venting in ducts 3 and 5. The restrictor cuts a thread into the retainer as it is screwed in. For that reason, the retainer should also be changed when a restrictor is repeatedly replaced.
Valve terminals MPA-L Key features – Pneumatic components Vertical stacking Additional functions can be added to each valve position between the sub-base and the valve. These functions are known as vertical stacking modules and enable special functioning or control of an individual valve position. An adjustable pressure regulator can be installed between the sub-base and the valve in order to control the force of the triggered actuator.
Valve terminals MPA-L Key features – Pneumatic components Pressure regulator Circuit symbol Vertical pressure shut-off plate Circuit symbol 18 Code Description Pressure regulator 1-32: PA Pressure regulator 1-32: PF Regulates the pressure upstream of the valve in duct 1 Same regulated pressure at duct 2 and duct 4 Venting in the valve from duct 2 to duct 3 and from duct 4 to duct 5 Regulator not affected by venting Regulator can always be adjusted Available in width 10 mm and 20 mm Press
Valve terminals MPA-L Key features – Pneumatic components Vertical pressure supply plate Circuit symbol Code Description Pressure regulator 1-32: PV Enables separate supply of the pressure in duct 1 and upstream of the valve Operating pressure –0.9 … +10 bar Available in width of 20 mm The valve terminal MPA-L can be supplied with compressed air at one or more points via supply modules and/or the right-hand end plate.
Valve terminals MPA-L Key features – Pneumatic components Compressed air supply and pilot air supply Graphical illustration Code Right-hand end plate, with supply ports Right-hand end plate: D Pilot air: – Right-hand end plate: D Pilot air: E Right-hand end plate, without supply ports Right-hand end plate: – Pilot air: – Notes Internal pilot air supply Pilot air is branched internally from port 1 in the right-hand end plate Exhaust air 3/5 via right-hand end plate or supply module Pilot exhaust air
Valve terminals MPA-L Key features – Pneumatic components Supply module Illustration Code Type Designation Notes Exhaust port: UD, UE, UF, UM, UN, UP or UG VMPAL-EG Exhaust plate for ducted exhaust air Exhaust port: – VMPAL-EU Flat plate silencer Type of module block 1-40: U VMPAL-SP-0 Supply module with elec trical interlinking module Additional supply modules can be used for larger terminals or to create additional pressure zones.
Valve terminals MPA-L Key features – Pneumatic components Creating pressure zones and separating exhaust air MPA-L offers a number of options for creating pressure zones if differ ent working pressures are required. Up to nine pressure zones in total are possible. Pressure zones are created by isol ating the internal supply ducts in a special sub-base. Each pressure zone must have its own compressed air supply. Compressed air can be supplied and vented via a supply module and/or the right-hand end plate.
Valve terminals MPA-L Key features – Pneumatic components Examples: Compressed air supply and pilot air supply Internal pilot air supply, right-hand end plate without supply ports The illustration opposite shows an example of the configuration and connection of the air supply with internal pilot air supply. The exhaust air (duct 3/5) is discharged via supply modules. The pilot exhaust air (duct 82/84) is discharged via the right-hand end plate. Special sub-bases are used to create pressure zones.
Valve terminals MPA-L Key features – Pneumatic components Sub-base MPA-L is based on a modular system consisting of sub-bases and valves. The sub-bases are connected together using tie rods and thus form the support system for the valves. They contain the connection ducts for supplying compressed air to and venting from the valve terminal as well as the working lines for the pneumatic drives for each valve.
Valve terminals MPA-L Key features – Pneumatic components Electrical interlinking module Illustration 2015/03 – Subject to change Code Type No.
Valve terminals MPA-L Key features – Assembly Valve terminal assembly Sturdy terminal assembly thanks to: Four through-holes for wall mounting Additional mounting brackets H-rail mounting -H- Note If the terminal is subject to strong vibrations or shock loads, use additional mounting brackets of the type VMPAL-BD for wall mounting. These should be attached to the valve terminal every 13 cm (one mounting bracket every 10 valve positions).
Valve terminals MPA-L Key features – Assembly Tie rod Design 1 2 3 4 1 2 3 4 Threaded rod Tie rod extender Sleeve Screw Mode of operation The tie rod for MPA-L consists of four parts: Threaded rod Tie rod extender Sleeve Screw This enables valve terminals of any length to be created.
Valve terminals MPA-L Key features – Assembly Tie rod – Components and design Tie rod (threaded rod) The threaded rod is used to create a cost-optimised fixed-grid tie rod. The threaded rod is required with valve terminal lengths exceeding 42.45 mm, for example at least four sub-bases (10.7 mm each), since only the combination of a threaded rod and sleeve offers the optimum compensation of tolerances (by compressing the seals between the sub-bases).
Valve terminals MPA-L Key features – Assembly Ordering data – Fixed-grid tie rod Reference length Part No. L = 10.65 x V + 14.85 x W + 21.15 x Z + 21.15 x S 42.3 … 62.65 62.66 … 72.30 72.31 … 81.95 81.96 … 91.60 91.61 … 101.25 101.26 … 110.90 110.91 … 120.55 120.56 … 130.20 130.21 … 139.85 139.86 … 149.50 149.51 … 159.50 159.51 … 169.15 169.16 … 178.80 178.81 … 188.45 188.46 … 198.10 198.11 … 207.75 207.76 … 217.40 217.41 … 227.05 227.06 … 236.70 236.71 … 246.35 246.36 … 256.00 256.01 … 266.00 266.
Valve terminals MPA-L Key features – Assembly Ordering data – Fixed-grid tie rod Reference length Part No. L = 10.65 x V + 14.85 x W + 21.15 x Z + 21.15 x S 522.51 … 532.50 532.51 … 542.50 542.51 … 552.50 552.51 … 562.50 562.51 … 572.50 572.51 … 582.50 582.51 … 592.50 592.51 … 602.50 602.51 … 612.50 612.51 … 622.50 622.51 … 632.50 632.51 … 642.50 642.51 … 652.50 652.51 … 662.50 662.51 … 672.50 672.51 … 682.50 682.51 … 692.50 692.51 … 702.50 702.51 … 712.50 712.51 … 722.50 722.51 … 732.50 732.51 … 742.
Valve terminals MPA-L Key features – Display and operation Display and operation Signal status display Manual override Each solenoid coil is allocated an LED that indicates its signal status. Indicator 12 shows the switching status of the coil for duct 2 Indicator 14 shows the switching status of the coil for duct 4 The manual override (MO) enables the valve to be actuated when not electrically activated or energised. The valve is switched by pushing the manual override.
Valve terminals MPA-L Key features – Electrical components Manual override (MO) MO with cover cap, non-detenting MO with cover cap, detenting without accessories, mounting Manual override is actuated by pushing it with a pointed object or screwdriver and reset by spring force (detenting position prevented due to cover cap). Clip cover onto pilot valve. The MO is then actuated by moving the slide on the cover cap.
Valve terminals MPA-L Key features – Electrical components Electrical connection – Left-hand end plate The electrical connection for connecting the valves to a higher-level controller is located in the left-hand end plate. The different connection options can be easily switched by replacing the left-hand end plate, while the pneumatic connections remain as they are. The valves are switched by means of positive or negative logic (PNP or NPN). Mixed operation is not permitted.
Valve terminals MPA-L Key features – Electrical components Pin allocation for electrical multi-pin plug connection – Sub-D plug, 9-pin Pin Address/coil 1) Pin Address/coil 1 0 6 5 2 1 7 6 3 2 8 7 4 3 9 0 V1) 5 4 -H- Note The drawing shows the view onto the pins of the Sub-D plug. 0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
Valve terminals MPA-L Key features – Electrical components Electrical multi-pin connection – Ordering data Designation Code Description Connecting cable for multi-pin plug connection with Sub-D plug socket Connecting cable: CA Cable outlet to front Connecting cable: CB (only with electrical connection code: MS6) Connecting cable: CC Connecting cable: – Connecting cable: CQ Cable outlet to front (only with electrical connection Connecting cable: CR code: MS6) Connecting cable: CS Suitable for use with energy
Valve terminals MPA-L Key features – Electrical components Pin allocation for electrical multi pin-plug connection – Flat cable, 40-pin Pin Address/coil 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 36 Pin Address/coil 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 0 V1) 0 V1) 0 V1) 0 V1) 0 V1) 0 V1) 0 V1) 0 V1) -H- Note The drawing shows the view onto the
Valve terminals MPA-L Key features – Electrical components Fieldbus connection/CPX terminal All functions and features of the electrical peripherals CPX are permitted in connection with the CPX interface. This means: The valves and outputs are supplied via the system supply for the CPX terminal The valves can optionally be actuated or switched off separately from the outputs The pneumatic interface (left-hand end plate) serves as an adapter between the two current feeds.
Valve terminals MPA-L Key features – Electrical components Instructions for use Equipment Operate system equipment with unlubricated compressed air if possible. Festo valves and cylinders are designed so that, if used as designated, they will not require additional lubrication and will still achieve a long service life. The quality of compressed air downstream of the compressor must correspond to that of unlubricated compressed air.
Valve terminals MPA-L Technical data -M-K- -P- Flow rate Up to 870 l/min Valve width 10 mm 14 mm 20 mm Voltage 24 V DC General technical data Valve terminal design Electrical actuation Type of actuation Nominal operating voltage [V DC] Max. no. of valve positions Max.
Valve terminals MPA-L Technical data Technical data – Valve width 10 mm Code for position function 1-32 Design Sealing principle Non-overlapping Reset method Switching times On Off Change over Standard nominal flow rate Operating pressure Pilot pressure Max.
Valve terminals MPA-L Technical data Technical data – Valve width 20 mm Code for position function 1-32 Design Sealing principle Non-overlapping Reset method Switching times On Off Change over Standard nominal flow rate Operating pressure Pilot pressure Max. tightening torque of valve mounting Materials Product weight M J N [ms] [ms] [ms] Piston spool valve Soft Yes Pneumatic spring 15 9 8 28 – 28 – 22 – [l/min] [bar] [bar] [Nm] 700 860 –0.9 … +10 3…8 0.
Valve terminals MPA-L Technical data Pneumatic connections Right-hand end plate Supply Exhaust port Pilot air supply Pilot exhaust port 1 3 5 12/14 82/84 Thread G1/4 (QS-G1/4, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2") Thread G1/4 (QS-G1/4, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2") Thread G1/4 (QS-G1/4, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, 5/16", 3/8", 1/2") Thread M7 (QSM-M7, straight or angled, for tubing O.D.
Valve terminals MPA-L Technical data Pilot pressure p2 as a function of working pressure p1 with external pilot air supply For valves with code for position function 1-32: M, J, B, G, E, W, X For valves with code for position function 1-32: N, K, H, D, I Pilot pressure p2 as a function of working pressure p1 for valves with mechanical spring return For valves in width 10 mm with code for position function 1-32: MS, NS, KS, For valves in width 14 mm with code for position function 1-32: MS, NS, KS, HS, DS H
Valve terminals MPA-L Technical data Current consumption per solenoid coil at nominal voltage Width 10 mm Nominal pick-up current Nominal current with current reduction Time until current reduction 14 mm 20 mm [mA] [mA] 50 10 50 10 110 23 [ms] 20 20 20 Electrical data – MPA-L with electrical interface for CPX terminal Intrinsic current consumption of valve terminal (internal electronics, without valves) At 24 V UEL/SEN1) [mA] Typically 13 At 24 V Uval2) [mA] Typically 35 Diagnostic message Underv
Valve terminals MPA-L Technical data Product weight Approx.
Valve terminals MPA-L Technical data Download CAD data è www.festo.com Dimensions Valve terminal with multi-pin plug connection 1 Solenoid valve VMPA1 2 Solenoid valve VMPA14 3 Solenoid valve VMPA2 Type 4 Manual override 5 Power supply module 6 Working ports L11) L21) L31) L41) 7 H-rail 8 H-rail mounting 9 Mounting holes L5 L6 L7 L8 aJ Earthing screw aA Multi-pin plug connection L9 L10 L11 L12 L13 L14 L15 L16 14.9 21.2 8.5 6.8 6.5 5.6 1.5 1 , MPA-L 89.
Valve terminals MPA-L Technical data Download CAD data è www.festo.com Dimensions Valve terminal with fieldbus connection 1 2 3 4 5 6 7 8 Solenoid valve VMPA1 Solenoid valve VMPA14 Solenoid valve VMPA2 Manual override 9 Mounting holes aJ Pneumatic interface, CPX ter minal Power supply module Working ports H-rail H-rail mounting aA CPX module aB Earthing screw Type L11) L21) L31) L41) MPA-L 170.9 + L2 + L3 + L4 m x 10.7 n x 14.9 o x 21.
Valve terminals MPA-L Technical data Download CAD data è www.festo.com Dimensions Valve terminal with I-Port interface/IO-Link 1 Solenoid valve VMPA1 2 Solenoid valve VMPA14 3 Solenoid valve VMPA2 Type B1 B2 MPA-L 107.3 66.3 Type L11) 4 Manual override 5 Power supply module 6 Working ports B3 7 H-rail 8 H-rail mounting 9 Mounting holes aJ Left-hand end plate with I-Port interface/IO-Link B4 B5 B6 D1 D2 D3 H1 H2 33.5 23.5 18.9 6.6 6.4 4.5 69.6 65.7 , H3 H4 H5 H6 H7 28.
Valve terminals MPA-L Technical data Download CAD data è www.festo.com Dimensions – Cover for multi-pin plug connection Cable outlet to front Type L1 Cable outlet to side L2 H1 H2 B1 B2 B3 14 26 34.5 34.5 – 27 – 29 , Cable outlet to front Cable outlet to side 108.3 114.5 27 – 44.4 32.4 Valve terminal with vertical stacking (example: valve terminal with I-Port interface/IO-Link) Type L1 L2 L3 H1 , VMPA…-B8-R 2015/03 – Subject to change 175.1 120.7 15 è Internet: www.festo.
Valve terminals MPA-L Accessories Ordering data Code Valve function Individual solenoid valve – Width 10 mm 5/2-way valve Position function 1-32: M Single solenoid Position function 1-32: MS Single solenoid, mechanical spring return Position function 1-32: MU Polymer poppet valve, single solenoid, mechanical spring return Position function 1-32: J Double solenoid 2x 3/2-way valve Position function 1-32: N Normally open Position function 1-32: NS Normally open, mechanical spring return Position function 1-
Valve terminals MPA-L Accessories Ordering data Code Vertical stacking modules – Width 10 mm Pressure regulator 1-32: PF Pressure regulator 1-32: PA Pressure regulator 1-32: PH Pressure regulator 1-32: PC Pressure regulator 1-32: PG Pressure regulator 1-32: PB Pressure regulator 1-32: PF Pressure regulator 1-32: PA Pressure regulator 1-32: PH Pressure regulator 1-32: PC Pressure regulator 1-32: PG Pressure regulator 1-32: PB Pressure regulator 1-32: PS Pressure gauge 1-32: VE Pressure gauge 1-32: VD Pressu
Valve terminals MPA-L Accessories Ordering data Code Fixed restrictor – Width 10 mm Pneumatic connection 3, 1-40: V03 Pneumatic connection 5, 1-40: Q03 Pneumatic connection 3, 1-40: V05 Pneumatic connection 5, 1-40: Q05 Pneumatic connection 3, 1-40: V07 Pneumatic connection 5, 1-40: Q07 Pneumatic connection 3, 1-40: V10 Pneumatic connection 5, 1-40: Q10 Pneumatic connection 3, 1-40: V12 Pneumatic connection 5, 1-40: Q12 Pneumatic connection 3, 1-40: V15 Pneumatic connection 5, 1-40: Q15 Pneumatic connection
Valve terminals MPA-L Accessories Ordering data Code Sub-base – Width 10 mm Duct separation to the right of sub-base 1-40: – Duct separation to the right of sub-base 1-40: T Duct separation to the right of sub-base 1-40: TR Duct separation to the right of sub-base 1-40: TS – Combination of four sub-bases – Width 10 mm Combination manifold block: Z – Electrical interlinking module – Width 10 mm Type of module block 1-40: C Type of module block 1-40: A Type of module block 1-40: C Type of module block 1-40
Valve terminals MPA-L Accessories Ordering data Code Individual solenoid valve – Width 14 mm 5/2-way valve Position function 1-32: M Position function 1-32: MS Position function 1-32: J 2x 3/2-way valve Position function 1-32: N Position function 1-32: NS Valve function Part No.
Valve terminals MPA-L Accessories Ordering data Code Sub-base – Width 14 mm Duct separation to the right of sub-base 1-40: – Duct separation to the right of sub-base 1-40: T Duct separation to the right of sub-base 1-40: TR Duct separation to the right of sub-base 1-40: TS – Combination of four sub-bases – Width 14 mm Combination manifold block: Z – Valve function Single, without electrical interlinking module, without cartridge fitting Single, with electrical inter linking module, single solenoid (for
Valve terminals MPA-L Accessories Ordering data Code Individual solenoid valve – Width 20 mm 5/2-way valve Position function 1-32: M Position function 1-32: MS Position function 1-32: J 2x 3/2-way valve Position function 1-32: N Position function 1-32: NS Position function 1-32: K Position function 1-32: KS Position function 1-32: H Position function 1-32: HS 5/3-way valve Position function 1-32: B Position function 1-32: G Position function 1-32: E 1x 3/2-way valve Position function 1-32: W Position functi
-V- New VMPA2-VSP Valve terminals MPA-L Accessories Ordering data Code Vertical stacking modules – Width 20 mm Pressure regulator 1-32: PA Pressure regulator 1-32: PF Pressure regulator 1-32: PC Pressure regulator 1-32: PH Pressure regulator 1-32: PB Pressure regulator 1-32: PG Pressure regulator 1-32: PL Pressure regulator 1-32: PN Pressure regulator 1-32: PK Pressure regulator 1-32: PM Pressure regulator 1-32: PV Valve function Part No. Type 0.5 … 8.5 bar 0.5 … 5 bar 2 … 8.5 bar 2 … 5 bar 2 … 8.
Valve terminals MPA-L Accessories Ordering data Code Description Sub-base – Width 20 mm Duct separation to the right of sub-base 1-40: – Duct separation to the right of sub-base 1-40: T Duct separation to the right of sub-base 1-40: TR Duct separation to the right of sub-base 1-40: TS – Electrical interlinking module – Width 20 mm Type of module block 1-40: D Type of module block 1-40: B 58 Single, No duct separation without electrical interlinking module, Duct 1 separated without cartridge fitting Duc
Valve terminals MPA-L Accessories Ordering data Code Description Tie rod: – Threaded rod for tie rod, width across flats 5 mm The threaded rod/sleeve combination is selected based on the number and width of the individual sub-bases.
-V- New VAMC Valve terminals MPA-L Accessories Ordering data Code Description Part No. Type PU1) – Mounting bracket Wall brackets should be mounted max.
Valve terminals MPA-L Accessories Ordering data Code Description Part No. Type Type of module block 1-40: U With electrical interlinking module, without cartridge fitting 560950 VMPAL-SP-0 Type of module block 1-40: U With electrical interlinking module, with cartridge fitting for tubing O.D.
Valve terminals MPA-L Accessories Ordering data Code Description Part No.
Valve terminals MPA-L Accessories Ordering data Code Description Part No. Type 2.5 m 5m 10 m 2.5 m 5m 10 m 2.5 m 5m 10 m 2.5 m 5m 10 m 2.5 m 5m 10 m 0.5 … 30 m 2.5 m 5m 10 m 0.5 … 30 m 2.5 m 5m 10 m 0.5 … 30 m 2.5 m 5m 10 m 0.5 … 30 m 2.5 m 5m 10 m 0.5 … 30 m 2.5 m 5m 10 m 0.
Valve terminals MPA-L Accessories Ordering data Code Cartridge fitting for sub-base in width 10 mm Standard AA connection for valve AB size 10 mm: – AJ AQ AK AL – – – – – 64 10 mm cartridge fitting, nickel-plated brass, for working lines, connection for tubing O.D. 10 mm cartridge fitting, plastic, L-shape, for working lines, connection for tubing O.D. 14 mm cartridge fitting, plastic, for working lines, connection for tubing O.D.
Valve terminals MPA-L Accessories Ordering data Code Cartridge fitting for supply module – Part No.
Valve terminals MPA-L Accessories Ordering data Part No.
Valve terminals MPA-L Accessories Ordering data Code Push-in fitting, self-sealing – Description Part No. Type PU1) With sealing ring, with external hex, connecting thread G1/4, for tubing O.D. With sealing ring, with external hex, L shape, connecting thread G1/4, for tubing O.D. 6 mm 8 mm 10 mm 6 mm 8 mm 10 mm 186296 186298 186300 186306 186308 186310 QSK-G1/4-6 QSK-G1/4-8 QSK-G1/4-10 QSKL-G1/4-6 QSKL-G1/4-8 QSKL-G1/4-10 1 1 1 1 1 1 With external hex, connecting thread G1/4, for tubing O.D.
Product Range and Company Overview A Complete Suite and Company Overview Our experienced engineers provide complete support at every stage of your development process, including: conceptualization, analysis, engineering, design, assembly, documentation, validation, and production Custom Automation Components Complete custom engineered solutions Custom Control Cabinets Comprehensive engineering support and on-site services Complete Systems Shipment, stocking and storage services The Broadest Range of A
Festo North America 1 Festo Canada Headquarters Festo Inc.
