Wireless Camcorder User Manual
Tour of Your Camera Record Button Mic Status Micro SD Card Slot Speaker Micro USB Port Strap Hook Video Mode Photo Mode Mode Button Direct Mode Cloud Mode Power Button Tripod Mount Clip Mount Magnet Mount Strap Mount English | 1
Getting Started Charging the Unit • Before first use, charge the battery fully by either adapter or PC USB. • Under charging, Status indicator will flash. Once complete, it will turn off automatically. Modes Navigation • Press Power button to turn on camera. • Press Mode button to switch between two camera modes (Video, Photo) and two wireless modes (Direct, Cloud). Two Camera Modes Insert micro SD card. (SD card is optional accessory) Take Video • Press Mode button to Video Mode.
Wireless Connection Direct Mode (Intranet) Direct Mode (Local) Mobile / PC Cloud Mode (Internet) Cloud Mode (Internet) AP USTREAM Cloud AP AP Mobile / PC Cloud Server 3G/4G Mobile Hotspot Three Cloud servers are available for access: USTREAM Live broadcast social media. Download free USTREAM APP or go to http://www.ustream.tv/ Note: 1. Cloud service may change depending on their policy. 2. Some mobiles may not activate Hotspot where there is no 3G/4G service in some countries.
Direct Mode (Mobile) Each camera has unique Camera ID. ( U2-xxxxxx) The Password is not required for first use, it is advised to go to [Setup] on APP to edit Password after connected. Connect Camera For iOS user: For Android user: • Set camera to Direct Mode . • Set camera to Direct Mode • On mobile, go to [Settings] • On mobile, activate WiFi [Wi-Fi] Choose a camera. connection. • Execute [Unieye] APP. • Execute [Unieye] APP. • Press camera bar to start. • Press camera bar to start.
Cloud Mode (Mobile) Before using Cloud Mode, setup Cloud AP and Cloud Server to camera. How to Setup Cloud AP on Direct Mode • On mobile, APP [Setup] [Cloud Setting] [Cloud AP]. Two ways to setup Cloud AP: 1. Select a WiFi network from [AP list] and enter Password. 2. Press [Other] from [AP list] Enter Network SSID and Password. Note: Mobile Hotspot can be set as Cloud AP. How to Setup Cloud Server on Direct Mode • New user, press then enter Email/Username/Password for auto-registration.
PC Application To use PC application, install PC [Unieye] software first. The WiFi functions on PC application are similar to mobile APP. Install PC [Unieye] Software from Camera • Plug in USB to connect camera and PC. • [Unieye] AutoRuns/AutoPlay is activated automatically. • If AutoRuns/AutoPlay is not activated: Go to [My computer] search [Unieye] for installation. • Once installed, software will be auto-launched. • Unplug USB for WiFi application or keep USB plugged for additional USB application.
Camera Indication Condition Status Indicator Take Video Slow flash Green Charging Slow flash Red Fully Charged Sound One time Two times Flash Red every 5 sec.
Trouble Shooting Situation Solution Camera cannot turn on Battery power is low. Recharge the battery. Camera is frozen Press Power button for 5 sec. to turn off. Press Power button twice to turn on. Camera cannot record No SD card or SD card is full. SD card cannot be recognized. Format SD card by [Unieye] or change SD card. Camera not found Turn on camera, switch to Direct Mode. Press "Refresh" on mobile or PC to scan again. Forget camera password Press both Mode and Record buttons to reset.
FCC & Safety Instruction FCC Regulations 15.19(a)(3): This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.105(b): NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
FCC & Safety Instruction RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.