User Manual

ManualsBrandsChicony Electronics ManualsComputers & AccessoriesWireless Mouse

A. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, Pursuant to Part 15 the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesired operation.

WARNING:

Use only shielded cables to connect I/O devices to this equipment.

You are cautioned that changes or modifications not expressly approved by the

party responsible for compliance could void your authority to operate the

equipment.

CAUTION: AVOID PROLONGED USE OF THE KEYBOARD WITHOUT

BREAKS.

Take regular breaks and keep a good posture. Consult your physician promptly if

you notice any lost of motion or pain in your wrist when using the keyboard.

INFORMATION FOR OPTICAL POINTING DEVICES ONLY :

User-observable light is 15 micro-watts in normal operation.

This product has been tested to comply with international Standard IEC

60825-1:(1993), incid. Amd.2(2001). This product uses LEDs that are inherently

Class 1.

Class 1 LED Product

Summary of content (10 pages)

PAGE 1
A. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to Part 15 the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 2
Contents Getting Started Features Preparing Keyboard, mouse and receiver Hardware Installation -- Connect the receiver +--- PS/2 Interface ( optional ) +--- USB Interface ( optional ) -- Inserting batteries +--- Inserting batteries into mouse +--- Inserting batteries into keyboard -- Setting frequency channel or ID +--- Setting frequency channel on keyboard and mouse +--- Setting ID on keyboard and mouse Software Installation -- Installing software for mouse -- Installing software for keyboard Displaying ke
PAGE 3
Getting Started Thank you for choosing this Wireless keyboard and Mouse Kits. It operates with digital radio technology to ensure no hinder communication between the keyboard, the mouse and your computer without connecting cable. The transmission and receiving of keyboard and mouse are free from angle restriction. There are two frequency channels each for keyboard and mouse to prevent malfunctions when you operate several radio transmission devices simultaneously. Features .
PAGE 4
(1) Please remove the battery compartment cover on the bottom of the mouse. (2) Insert the two alkaline batteries (AA) in the battery compartment. (3) Fix the battery compartment cover (1) on the bottom of mouse again Dangerous!! Please only use batteries of the same type. . Inserting batteries in keyboard The keyboard requires two alkaline batteries (AA). (1) Remove the battery compartment cover (1) on the bottom of the keyboard by pushing it in the direction of arrow. (2) Insert two AA batteries.
PAGE 5
Software Installation . Installing software for mouse The software for the mouse provided, only supports Windows 98, Windows ME, Windows 2000 and Windows XP. Install the software to use all mouse functions. (1) Start the computer and insert the data carrier in the corresponding drive. (2) Start the" Setup "program from the data carrier and follow the instructions on the screen. You may also use any standard mouse software.
PAGE 6
these functions (e.g. Windows ME, Windows 2000 and Windows XP). To use the multimedia keys in Windows 98 you must install the software provided. 1. Standby mode Depending on the settings in the BIOS Setup or operating system the computer switches to a standby mode (not under Windows NT). 2. Power Down Depending on the settings in the BIOS Setup or operating system the computer switches to power off mode. 3. Internet With this key you can start the standard browser for your system. 4.
PAGE 7
14. Decreasing the volume This key decreases the volume of the connected loudspeakers. 15. Mute Use this key to switch on/off the connected loudspeaker. 16. Increasing the volume This key increases the volume of the connected loudspeakers. b. Additional Hotkeys and Scroll wheel 1. Word Activate the Windows default Word program 2. Excel Copy the content you selected Activate the Windows default Excel program 3. Scroll wheel (Mode 1) Use the scroll wheel to control the document or website Scroll up and down.
PAGE 8
• Arrange your workplace in accordance with the recommendations for an ergonomic workstation provided in the PC Operating Manual. • Position the keyboard so that you can use it without any noticeable strain. The keyboard should be level with the upper part of you body. This prevents any tension in the shoulders and arms. • The distance between the keyboard and the edge of the desk should be 5 to 10 cm. • When typing, hold your hands and forearms so that they form as natural a line as possible.
PAGE 9
Product Specification Receiver Interface: USB interface. Frequency band: Two channels for keyboard and two channels for mouse. Keyboard – 27.145 MHz and 27.195 MHz Mouse – 26.995 MHz and 27.
PAGE 10
Troubleshooting and tips The keyboard or mouse does not operate following installation or is not recognized. . Make sure that the batteries have been inserted correctly according to the polarity and the receiver is well connected. . Check that your USB port is configured properly. . Check whether the respective channels and ID are set on the receiver and the keyboard or mouse. . Make the connection between the receiver and the keyboard and mouse.