User Manual

English
WARNING
To reduce the risk of fire or electric shock, do not expose the unit to
rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing
to qualified personnel only.
Owner’s Record
The model number and the serial number are located inside the battery compartment of
the mouse. Record the serial number in the space provided below. Refer to this number
whenever you call your Sony dealer regarding this product.
Model No. VGP-WMS10, VGP-WRC8
Serial No. ____________________
Safety information
Do not look directly into the lens. The laser light may cause eye injury.
In the following circumstances, set the power to off and have it checked by qualified
personnel before continuing its use.
–
Water or a foreign object has entered the mouse.
–
Smoke is coming out of the mouse.
–
There is an unusual noise or smell.
–
The mouse is dropped or the exterior of the mouse has broken.
Do not place the mouse in a location subject to:
–
On an unstable surface
–
In very humid areas or where there is no ventilation
–
Excessive dust
–
Direct sunlight or extreme heat
–
Mechanical vibration or shock
–
Greasy fumes
If the mouse is brought directly from a cold to a warm location or is placed in a very
damp room, moisture may condense on the inside of the mouse. If this occurs, the
mouse may not work properly.
Keep away the wireless receiver and battery from children.
Precautions on using the batteries
If the battery liquid is leaking:
– Do not touch the battery liquid directly. If your eyes, skin, or clothing comes into contact with the
battery liquid, wash well with pure water. If you have skin inflammation or a wound results,
consult a doctor immediately.
– Wipe the battery compartment carefully, and insert new batteries.
Dispose of used batteries promptly and properly. Discard used batteries according to
the manufacturer’s instructions. In some areas, the disposal of batteries in household or
business waste may be prohibited. Please use the appropriate public collection system.
Batteries may explode or leak if recharged, or disposed of in fire.
Do not disassemble, heat above 60 ˚C (140 °F) or incinerate.
Replace only with the same or equivalent type recommended by the manufacturer. Be
sure to use batteries specified in “Power requirements” of “Specifications.” Danger of
explosion if battery is incorrectly replaced.
Insert the batteries with the correct +/– orientation.
When the batteries have run out, or when you intend to not use the mouse over a
prolonged period, remove the batteries.
Do not short-circuit the metal terminals of the battery or wet them with any liquid, for
example, water, coffee, or juice.
For customers in the U.S.A.
This device contains the following wireless devices;
Wireless mouse (VGP-WMS10), Wireless receiver (VGP-WRC8)
The following FCC statements apply only to the version of this model
manufactured for sale in the USA. Other versions may not comply with FCC
technical regulations.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
If you have questions about this product, you can write to the Sony Customer
Information Service Center at 12451 Gateway Blvd., Fort Myers, FL 33913,
USA or find Sony Customer Service on the Web site at:
http://esupport.sony.com/EN/VAIO/ for customers in USA or
http://www.sony.ca/support/ for customers in Canada
Declaration of Conformity
Trade Name: SONY
Model No.: VGP-WRC8
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A.
Telephone No.: 858-942-2230
(For FCC-related matters only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
For customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation of the
device.
For customers in the U.S.A. and Canada
This wireless mouse and wireless receiver comply with FCC/IC radiation
exposure limits set forth for uncontrolled environment and meet the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102
of the IC radio frequency (RF) Exposure rules. This wireless mouse and
wireless receiver have very low levels of RF energy that it deemed to comply
without maximum permissive exposure evaluation (MPE). But it is desirable
that they should be installed and operated with at least 20cm and more
between the radiators and person’s body (excluding extremities: hands, wrists,
feet and ankles).
This wireless mouse and wireless receiver and their antennas must not be co-
located or operating with any other antenna or transmitter except Grant
condition.
This wireless mouse is classified as a CLASS 1 LASER PRODUCT and
complies with the Laser Products Safety Standard IEC/EN60825-1(2007).
Caution - Repair and maintenance of this wireless mouse should be made only
by Sony authorized technicians. Improper repairs and use can create safety
hazards.
Caution - Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
You can find the following sticker on the bottom of the wireless mouse.
Conditions of use
Do not use this device on hospital premises. Doing so may cause medical devices to
malfunction.
Do not use this device on an aircraft, as doing so may cause the aircraft's equipment to
malfunction.
If using this device near a pacemaker, make sure it is at least 20 cm (8 inches) away
from the pacemaker.
Sony is not responsible for any interference that you may experience or that may be
caused when operating this device.
Check for and respect airline restrictions on use of wireless capabilities. If use of the
wireless function is prohibited on the airline, set the power switch on this device to
OFF before boarding.
For customers in other countries and regions
This wireless mouse is classified as a CLASS 1 LASER PRODUCT and
complies with the Laser Products Safety Standard IEC/EN60825-1(2007).
Caution - Repair and maintenance of this wireless mouse should be made only
by Sony authorized technicians. Improper repairs and use can create safety
hazards.
Caution - Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
You can find the following sticker on the bottom of the wireless mouse.
Conditions of use
If radio interference with other devices occurs while using this device, do not use the
wireless functionality. Use of the wireless functionality may cause a malfunction of the
devices, resulting in an accident.
Do not use this device in any medical institutions, including hospitals, or while you are
close to any electric medical equipment. Radio waves may cause a malfunction of such
equipment, resulting in a serious accident.
Check for and respect airline restrictions on use of wireless capabilities. If use of the
wireless function is prohibited on the airline, set the power switch on this device to
OFF before boarding. Radio waves may cause a malfunction of the aircraft’s equipment,
resulting in a serious accident.
Do not use this device in a crowded place, such as in a crowded train car. Radio waves
may cause a malfunction of pacemakers implanted in other people’s bodies.
If you urgently need to disable wireless functionality, set the power switch on this
device to OFF.
Before Use
The Wireless Mouse is designed for use with IBM PC/AT compatible
computers with USB ports and pre-installed with the Windows 7, Windows
Vista or Windows XP (SP2 and after) operating system (as of January 2011).
When not in use, the receiver can be stored directly in the storage to make it
easier to carry around.
Notes
Operation is not guaranteed for all computers meeting the above system requirements.
Operation is not guaranteed for home-built computers, white box PCs, and computers
with OS upgrades and multi-boot systems.
Names of Parts
Wireless mouse
Right button
Wheel button
Left button
Lens
Power switch
Status light
Wireless receiver
USB Plug
Preparations
Inserting the battery into the mouse
1 Set the power switch located on the bottom of the mouse to
OFF.
2 Open the battery compartment cover and insert the supplied
LR6 (size AA) battery with the correct + – orientation.
3 Close the battery compartment cover.
Replacing the battery
When cursor movement becomes sluggish and the communication distance
between the mouse and your personal computer decreases, check the status
light on the mouse. The status light flashing orange indicates that the battery
life is running low. Replace the battery when this occurs.
When not using the mouse, set the power switch to OFF. This will make the
battery last longer.
Connecting the mouse with the receiver
Note
Use the mouse in combination with the supplied receiver. The mouse cannot be
connected to any other kind of receivers.
1 Insert the receiver into the computer’s USB port.
When connecting to the USB port, connect to the USB port with “ ”
mark.
2 Set the power switch of the mouse to ON.
The status light lights up green (for approx. 10 seconds).
3 Move the mouse. If the pointer displayed on your screen moves
appropriately, the connection is complete.
To stop using the mouse
Disconnect the receiver from the USB port of the computer.
You can disconnect and connect the receiver without turning the computer off.
hint
When you carry the personal computer, disconnect the receiver from the personal
computer.
To store the receiver in the mouse
The receiver can be stored in the battery compartment cover of the mouse.
Notes on use
Due to the characteristics of the laser sensor, the mouse may not work
properly on transparent surfaces or on a mouse pad that has a clear surface.
Avoid using on such materials, or use a commercially-available mouse pad
that is compatible with a laser sensor mouse.
The mouse can normally be operated within about a 10 m (32 ft.) radius
around the receiver. Depending on the usage environment, sometimes the
usable distance may be notably shorter, preventing normal operation.
In such a case, take the following measures:
– Use the mouse as far away from other wireless devices as possible.
– Use the mouse closer to the receiver.
– Use a mouse pad.
hint
If necessary, you can adjust the mouse pointer speed under “Mouse Properties.”
To display “Mouse Properties” with the Windows 7 operating system, click “Hardware
and sound,” and then “Mouse” in the “Control Panel.”
To display “Mouse Properties” with Windows Vista and Windows XP operating systems,
click “Mouse” in the “Control Panel.” (If you use Windows XP operating system, switch to
Classic View.)
Cleaning the outside of the mouse
When you clean the mouse, make sure to remove the battery.
Clean the mouse with a soft and dry cloth. Do not use any type of abrasive pad,
scouring powder, or solvent such as alcohol or benzine.
Specifications
Wireless mouse
Communication method Digital wireless transmission *
Position tracking method Laser sensor type (C
lass 1 Laser)
Sensor resolution
Communication distance 10 m (32 ft.) max. li
ne of sight **
Power requirements
LR6 (size AA) battery
Battery life
Dimensions
Mass
Wireless receiver
Interface USB (Also usable with a USB 2.0 port)
Frequency band
2.4 GHz
Dimensions
Mass
Miscellaneous
Operating temperature 5 °C to 35 °C (41 °F to 95 °F)
(temperature gradient less than 10 °C (18 °F)/hour)
Operating humidity 20% to 80% (not condensed), provided that humidity
is less than 65% at 35 °C (95 °F)
(hygrometer reading of less than 29 °C (84 °F))
Storage temperature
–20 °C to +60 °C (–4 °F to +140 °F)
(temperature gradient less than 10 °C (18 °F)/hour)
Storage humidity 10% to 90% (not condensed), provided that humidity
is less than 20% at 60 °C (140 °F)
(hygrometer reading of less than 35 °C (95 °F)
Supplied accessories
Wireless receiver (VGP-WRC8)
LR6 (size AA) Alkaline battery
Operating Instructions (this document)
* This unit does not support communication with wireless LAN and
Bluetooth®.
** The communication range varies, due to walls or other obstacles
between devices, the materials used in the walls, environmental
conditions such as radio frequency interference, and the software
program used.
*** This estimate is based on five hours of use per day, five days per week.
These could be different depending on the usage environment.
Design and specifications are subject to change without notice.
Troubleshooting
If you are not able to locate a solution in this section, contact a Sony authorized
dealer.
Nothing happens when I press a mouse button.
The receiver is not connected properly to the USB port.
Close all programs, and then reconnect the receiver to your computer.
The operating system is not compatible.
Use a supported operating system.
The USB port is not available.
Check the “System Properties” of your personal computer.
The mouse battery is drained.
If the status lamp does not light when the mouse is turned on, replace the
battery. For details, see “Preparations”.
The mouse and receiver are not communicating.
–
Perform steps of “Enabling communication between the mouse and receiver”
to ensure that proper communication is possible.
–
In some operating environments, the usable distance may be notably shorter,
preventing normal operation. In such a case, use the mouse farther away from
other electronic devices such as other computers and displays.
–
If the mouse is too far from the receiver, communication is not possible. Bring
the mouse and receiver closer together.
The mouse may have difficulty communicating in a 2.4 GHz wireless LAN
environment.
It is best to use the mouse in a location with low interference from wireless
devices.
The scrolling features do not work.
The operating system is not compatible.
Use a supported operating system.
The program you are using is not compatible with the scrolling features.
–
The scrolling features only work with programs that use a scroll function.
–
Some programs do not support the scrolling features.
After the receiver was installed, the computer was returned to normal mode from
power-saving mode.
Disconnect the receiver from the USB port, wait a few seconds, and then
reconnect it.
The pointer does not move when I move the mouse.
Processing performed by Windows or other software may temporarily disable the
mouse. Wait a few moments for the processing to finish before using the mouse.
You may find some useful solutions in your computer’s operating instructions.
Refer to the manuals provided with your computer.
Also see “Nothing happens when I press a mouse button.”
The mouse pointer does not move smoothly across the screen.
Due to the characteristics of the laser sensor, the mouse may not work properly
on transparent surfaces, or on a mouse pad that has a clear surface. Avoid using
on such materials. A commercially-available mouse pad that is compatible with a
laser sensor mouse is recommended.
I cannot make the computer exit power-saving mode with the
mouse, or it takes a long time.
Press any key or the power button on the keyboard.
When I start the computer an error message appears, saying that
the mouse is not connected.
Select the check box that offers not to display this message again, and then click
“OK”.
The mouse does not move smoothly after returning the computer
from the power-saving mode.
Disconnect the receiver from the USB port, wait a few seconds, and then
reconnect it.
After connecting the receiver, it takes a while before the mouse can
be used.
If the receiver is connected while the computer is processing commands from
Windows, other software, or another USB device, it may take a while for the
computer to detect the receiver.
Trademarks and notice
VAIO is a trademark of Sony Corporation.
Microsoft, Windows, and Windows Vista are registered trademarks of
Microsoft Corporation in the United States and/or other countries.
IBM and PC/AT are registered trademarks of International Business Machines
Corporation.
In this manual, Microsoft® Windows® XP Home Edition and Microsoft®
Windows® XP Professional are referred to as Windows XP.
In this manual, Microsoft® Windows Vista® Home Basic, Microsoft® Windows
Vista® Home Premium, Microsoft® Windows Vista® Business and Microsoft®
Windows Vista® Ultimate are referred to as Windows Vista.
In this manual, Microsoft® Windows® 7 Ultimate, Microsoft® Windows® 7
Professional, Microsoft® Windows® 7 Home Premium, Microsoft® Windows® 7
Home Basic or Microsoft® Windows® 7 Starter are referred to as Windows 7.
All other names of systems, products, and services are trademarks of their
respective owners. In this manual, the ™ or ® marks are not specified.
Français
AVERTISSEMENT
Pour réduire les risques d’incendie ou d’électrocution, n’exposez
pas l’appareil à la pluie ou l’humidité.
Pour prévenir les risques d’électrocution, n’ouvrez pas le boîtier.
Confiez toutes les réparations à un technicien qualifié.
Informations d’identification
Le numéro de modèle et le numéro de série sont indiqués à l’intérieur du logement des
piles de la souris. Notez le numéro de série dans l’espace ci-dessous. Reportez-vous à ce
numéro chaque fois que vous appelez votre détaillant Sony au sujet de ce produit.
Numéro de modèle VGP-WMS10, VGP-WRC8
Numéro de série ____________________
Informations de sécurité
Ne regardez pas directement dans la lentille. La lumière laser pourrait causer des
lésions oculaires.
Dans les situations suivantes, éteignez la souris et faites-la vérifier par un technicien
qualifié avant de continuer à l’utiliser.
–
De l’eau ou un corps étranger s’est infiltré dans la souris.
–
De la fumée s’échappe de la souris.
–
La souris produit une odeur ou un bruit inhabituel.
–
La souris a fait une chute ou son boîtier extérieur est endommagé.
Ne placez pas la souris dans un endroit :
–
dont la surface est instable;
–
situé dans des zones très humides ou mal ventilées;
–
soumis à une poussière excessive;
–
soumis à la lumière directe du soleil ou à une chaleur extrême;
–
soumis à des chocs ou vibrations mécaniques;
–
exposé aux fumées huileuses.
Si la souris est transportée directement d’un endroit froid à un endroit chaud ou si elle
est installée dans une pièce très humide, de la condensation peut se former à l’intérieur
de la souris. Si cela se produit, la souris peut ne pas fonctionner correctement.
Gardez le récepteur sans fil et la pile hors de la portée des enfants.
Précautions relatives à l’utilisation des piles
En cas de fuite du liquide d’une pile :
–
Ne touchez pas directement le liquide de la pile. Si le liquide de la pile entre en
contact avec vos yeux, votre peau ou vos vêtements, lavez-les bien avec de l’eau claire.
Si le contact cause une plaie ou une inflammation de la peau, consultez un médecin
immédiatement.
–
Essuyez soigneusement le logement des piles, puis insérez de nouvelles piles.
Veillez à vous départir des piles usées rapidement et de façon appropriée. Débarrassez-
vous des piles usées en suivant les instructions du fabricant. Dans certaines régions, il
est interdit de jeter les piles avec les déchets ménagers ou commerciaux. Veuillez
utiliser le système de collecte public approprié.
Les piles peuvent exploser ou fuir lorsqu’elles sont rechargées ou jetées dans les
flammes.
Vous ne devez pas les démonter, les exposer à une température de plus de 60 °C
(140 °F) ou les incinérer.
Remplacez-les uniquement par des piles identiques ou d’un type équivalent
recommandé par le fabricant. Assurez-vous d’utiliser les piles spécifiées dans la section
« Alimentation requise » des « Caractéristiques techniques ». La pile pourrait exploser
si elle n’est pas remplacée correctement.
Insérez les piles en respectant la polarité +/–.
Lorsque les piles sont épuisées ou que vous prévoyez ne pas utiliser la souris pendant
une période prolongée, retirez les piles.
Ne court-circuitez pas les bornes métalliques de la pile et ne les mouillez pas avec un
liquide tel que de l’eau, du café ou du jus.
Pour les clients résidant au Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
L’utilisation de ce dispositif est autorisée seulement aux deux conditions
suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du
dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si
ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Pour les clients résidant aux États-Unis et au Canada
Cette souris sans fil et ce récepteur sans fil sont conformes aux limitations
concernant l’exposition aux radiations établies par le FCC/IC pour un
environnement non contrôlé, ainsi qu’aux directives relatives à l’exposition aux
radiofréquences (RF) du FCC spécifiées dans le supplément C du bulletin
OET65 et au règlement RSS-102 relatif à l’exposition aux radiofréquences (RF)
de IC. Cette souris sans fil et ce récepteur sans fil présentent des niveaux
d’énergie RF très faibles considérés comme conformes et ne nécessitent pas
d’évaluation d’exposition maximale admise (MPE). Il est toutefois souhaitable
d’installer et d’utiliser les appareils en respectant une distance minimale de 20
cm entre les appareils rayonnants et vous (sans compter les extrémités : mains,
poignets, pieds et chevilles).
Cette souris sans fil, ce récepteur sans fil et leurs antennes ne doivent pas être
placés à proximité d’autres antennes ou émetteurs ni fonctionner avec eux, sauf
autorisation spéciale.
Cette souris sans fil classée CLASS 1 LASER PRODUCT est conforme à la
norme de sécurité des appareils à laser IEC/EN 60825-1(2007).
Avertissement - La réparation et l’entretien de cette souris sans fil ne doivent
être effectués que par des techniciens autorisés par Sony. Les réparations et
utilisations inappropriées peuvent causer des accidents.
Avertissement - L’utilisation de commandes et de réglages ou l’exécution de
procédures différentes de celles spécifiées dans ce document peuvent vous
exposer à une radiation dangereuse.
L’étiquette suivante est apposée sous la souris sans fil.
Conditions d’utilisation
N’utilisez pas cet appareil dans les locaux d’un hôpital. Ceci pourrait compromettre le
fonctionnement des appareils médicaux.
N’utilisez pas cet appareil dans un avion, car ceci pourrait compromettre le
fonctionnement de ses équipements.
Lors de l’utilisation à proximité d’un stimulateur cardiaque, assurez-vous de placer
l’appareil à une distance d’au moins 20 cm (8 po) du stimulateur cardiaque.
Sony ne peut être tenu responsable pour toute interférence subie ou causée lors du
fonctionnement de cet appareil.
Respectez les restrictions des transporteurs aériens relatives à l’utilisation des appareils
sans fil. Si l’utilisation de la fonction sans fil est interdite dans l’avion, réglez le
commutateur d’alimentation de cet appareil sur OFF avant l’embarquement.
Avant toute utilisation
Cette souris sans fil peut être utilisée avec les ordinateurs compatibles IBM PC/
AT avec ports USB sur lesquels Windows 7, Windows Vista ou Windows XP
(SP2 et ultérieur) est préinstallé (à compter de janvier 2011).
Lorsqu’il n’est pas utilisé, le récepteur peut être rangé directement dans le
logement pour faciliter le transport.
Remarques
Le fonctionnement n’est pas garanti pour tous les ordinateurs répondant aux exigences
de système ci-dessus.
Le fonctionnement n’est pas garanti pour les ordinateurs assemblés à la maison, les PC
de type boîte blanche et les ordinateurs avec mises à jour de système d’exploitation et
systèmes à double amorçage.
Noms des pièces
Souris sans fil
Bouton droit
Bouton roulette
Bouton gauche
Lentille
Interrupteur
d’alimentation
Témoin d’état
Récepteur sans fil
Connecteur USB
Préparations
Insertion de la pile dans la souris
1 Réglez l’interrupteur d’alimentation situé sous la souris sur
OFF.
2 Ouvrez le couvercle du logement de pile et insérez la pile LR6
(taille AA) fournie en respectant la polarité +/–.
Wireless Laser Mouse
VGP-WMS10
Operating Instructions/Mode d’emploi/
Manual de instrucciones
¡IMPORTANTE!
POR FAVOR LEA DETALLADAMENTE ESTE MANUAL DE INSTRUCCIONES ANTES DE CONECTAR Y OPERAR
ESTE EQUIPO. RECUERDE QUE UN MAL USO DE SU APARATO PODRÍA ANULAR LA GARANTÍA.