Installation Instructions

ManualsBrandsChief Manufacturing ManualsAVHeight Adjustable 4 Screen Desk Mount

8832-000142 RevL

2014 Milestone AV Technologies

www.chiefmfg.com

06/14

Chief, a products division of Milestone AV Technologies

6436 City West Parkway, Eden Prairie, MN 55344

• P: 800.582.6480 / 952.225.6000

• F:877.894.6918 / 952.894.6918

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Horizontal And Vertical Table Stands

and Accessories

Model: KTP-Series

The KTP-Series is a free standing, pole mount solution for multiple displays.

KTP-440 / KTP-445

KTP-230

KTP-320

KTP-220 / KTP-225

KTP-325

CAUTION!

To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be

attached to it, thoroughly study all instructions and illustrations before you begin the installation.

• If you have any questions about this installation, contact Chief.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series The KTP-Series is a free standing, pole mount solution for multiple displays. KTP-320 KTP-220 / KTP-225 KTP-230 KTP-325 KTP-440 / KTP-445 BEFORE YOU BEGIN CAUTION! To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be attached to it, thoroughly study all instructions and illustrations before you begin the installation.
PAGE 2
Model: KTP-Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION • • • • • WEIGHT CAPACITIES Phillips Head Screw Driver 3/4" Wrench 3/32" Hex Key (provided) 5/32" Hex Key (provided) 7/32" Hex Key (provided) KTP-220 / KTP-225: 35 lbs. per monitor KTP-230: 35 lbs. per monitor KTP-320 / KTP-325: 30 lbs. per monitor KTP-440 / KTP-445: 20 lbs. per monitor PARTS Carefully inspect components for shipping damage.
PAGE 3
Installation Instructions Model: KTP-Series (160) (10 Includes 210, 220, 230) (180) (200) (120) (190) (20) (170) (130) (140) 250 260 (30) (110) (100) 270 (80) 240 (40) (90) (50) (70) (60) Figure 1: Parts ASSEMBLY AND INSTALLATION (210) Mount Assembly (60) KTP-230 Assembly To assemble the KTP-230: (220) 1. Assemble pole (60) to base (40) using one 3/8-16 x 1" FHCS (90).
PAGE 4
Model: KTP-Series Installation Instructions Display Installation Attach Centris Head to Flush Mount Display (230) Keep equal distance between mount and clamp when tightening (220) (210) CAUTION! CAUTION: If display uses a screw size other than those included in the kit, DO NOT use the screws provided. Using the wrong screws could result in damage to your monitor. 1. Install two M4 x 12mm Phillips pan head screws (160) into two upper mounting holes in display back.
PAGE 5
Installation Instructions Model: KTP-Series Display Centris Head 6. Secure Centris head to display using four M4 x 20mm Phillips pan head screws (170) [if using 3/8" (190) spacers], or four M4 x 30mm Phillips pan head screws (180) [if using 3/4" (200) spacers] (see Figure 11). Phillips Pan Head Screw (170 or 180) Centris Head (20, 30) Spacer (190 or 200) (160) Figure 8: Secure Display to Centris Bracket Attach Centris Head to Recessed Mount Display 1.
PAGE 6
Model: KTP-Series Installation Instructions Display Pitch and Roll Adjustment To adjust display pitch or roll position: (20, 30) 1. Loosen Centris bracket front adjustment knob. (see Figure 15) End Lock 2. Tilt display up or down, or adjust display roll left or right until properly positioned. 3. Tighten Centris bracket front adjustment knob.
PAGE 7
Installation Instructions Model: KTP-Series 7
PAGE 8
Model: KTP-Series 8 Installation Instructions