INSTALLATION INSTRUCTIONS XSM XTM FUSION EXTRA LARGE HEIGHT ADJUST FLAT PANEL MOUNTS XSM/XTM Series
XSM/XTM Series Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions XSM/XTM Series DIMENSIONS XSM NOTES: 1. MAX MOUNTING PATTERN IS 46" (1168.4 mm) WITHOUT REVERSING UPRIGHTS. 2. MAX MOUNTING PATTERN IS 48.4" (1229.4 mm) WITH REVERSED UPRIGHTS. 3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK ENGAGEMENT IS .56"[14.2]. MOUNT IS 2.23"[56.6mm] DEEP WHEN FLAT TO WALL. 20.6 .81 30 1.18 39.1 1.54 24.3 .96 73.9 2.91 25.4 1.00 MINIMUM UPRIGHT SPACING 24" 8.3 .33 685.8 27.00 0 15 .59 44.5 1.75 383.4 15.10 56.6 2.23 75 2.95 419.
XSM/XTM Series Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un for
XSM/XTM Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 7/32" (5.5mm) Wood Stud 5/16" (7.9mm) Concrete PARTS [A-K used on XSMU/XTMU Models Only] A (6) M6x16mm C (6) M8x20mm [Included with XSMXXXX / XTMXXXX Models Only] B (6) M6x25mm D (6) M8x30mm F (6) M10x40mm Custom XSMXXXX / XTMXXXX Hardware H (6) M6 E (4) M8x50mm M (1) G (6) M10x50mm I (6) M8 JA (6) .750x.323x.250" KA (1) M5 JB (6) 1.00x.400x.
XSM/XTM Series Installation Instructions INSTALLATION Center of screen The XTM and XSM have been designed to be mounted directly onto either a wood stud or concrete wall. The XTM has brackets which allow the display to be tilted. The XSM has static brackets which keep the display in an upright position. 7-1/2" (190.
Installation Instructions XSM/XTM Series WARNING: ELECTRICAL SHOCK HAZARD! CUTTING 5 OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.
XSM/XTM Series Installation Instructions Attaching Interface Brackets to Display Switching Interface Brackets (Optional) 1. If an installation situation makes adjusting the location of interface brackets necessary, there are several options. Align the center of the bracket with center of screen. (See Figure 4) NOTE: The diamond-shape hole in the bracket corresponds to 1. The wall brackets may be adjusted side to side at the point of attachment. (See Figure 5) 2.
Installation Instructions 3. XSM/XTM Series If necessary, the tilt interface bracket knobs may be switched to allow the interface brackets to be reversed. (See Figure 6) a. Remove display from mount. b. Remove interface brackets from display. c. Hold the right interface bracket horizontally, tightly gripping it so that spacers do not move. d. Remove the knob, washer and screw. e. Replace the knob, washer and screw in the opposite order, with the knob on the inside of the bracket. f.
XSM/XTM Series Installation Instructions XTM Model XSM Model NOTE: Proceed to Step 8 for XSM Model instructions. 8. 3. Push interface bracket tab all the way down so that the lower mounting slot is blocked. (See Figure 10) Hang top hook of interface brackets onto the top bar of the mount. (See Figure 9) NOTE: The screen initially installs into the "kickstand mode" to allow easy cable access. 4. Slide screen and bars to desired viewing position. 5. Route cables between wall and bars.
Installation Instructions XSM/XTM Series Adjusting Roll/Height of Wall Brackets Locking XSM Mount (Optional) NOTE: The height adjust wall brackets allow adjustment of Add padlock (not included) to interface bracket tab to lock the XSM mount. (See Figure 13) + 1/2". 1. Turn to right (tighten) to raise side of screen. (See Figure 11) 2. Turn to left (loosen) to lower side of the screen.
XSM/XTM Series Installation Instructions USA/International Europe Chief, a products division of Milestone AV Technologies 8800-002518 Rev00 2014 Milestone AV Technologies www.chiefmfg.com 03/14 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.