INSTALLATION INSTRUCTIONS LCD Swivel Stand MSS6000
MSS6000 Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and Milestone AV Technologies, Inc., and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions MSS6000 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestig
MSS6000 Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 5/32" (Provided) 3/16" (Provided) 3/8" PARTS A (1) B (5) .5x.5x.
Installation Instructions MSS6000 INSTALLATION 1. Mount Installation Remove slide plate assembly from the base by removing four 5/16-18 x 3/4" button head cap screws, and four 1/4" flat washers. (See Figure 3) Free Standing (not anchored) Applications Only: NOTE: Do not perform this step if you are going to anchor the stand to a surface. 1. 1 x4 4 xx44 Install five rubber bumpers (B) on bottom of stand.
MSS6000 Installation Instructions Display Installation Site Preparation for Mounting to Surface WARNING: EXCEEDING WEIGHT CAPACITY CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the combined weight of all components does not exceed 150 lbs (68.04 kg). CAUTION: TURNING DISPLAY CAN CAUSE DAMAGE TO SURROUNDING OBJECTS. Make certain location provides enough area for the display to rotate + 45° without being obstructed.
Installation Instructions MSS6000 1 May remove pin and nut and move to lower holes Remove bolt or padlock if used 2 1 2 Pin in "Closed" position move to "Open" position to remove display A padlock or bolt may be placed through latch holes 4 Figure 7 Removing Display from Mount 1. Remove bolt or padlock from faceplate (if used). (See Figure 8) NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. 2.
MSS6000 Installation Instructions ADJUSTMENTS Display Roll Adjustment Display Height Adjustment The MSS6000 provides limited display roll adjustment for the purpose of leveling the display. To level the display: CAUTION: Displays are fragile. Allowing the display to drop 1. Loosen upper and lower roll adjustment nuts. (See Figure 10) 2. Level display. (See Figure 10) 3. Tighten roll adjustment nuts. to bottom of stand may result in damage to the display. 1.
Installation Instructions MSS6000 Display Swivel Tension Adjustment Display swivel tension is pre-set at the factory. Swivel tension will vary depending on the weight of display being mounted. If swivel tension adjustment is required: 1. Disconnect all cords and cables from display. 2. Follow steps in Removing Display from Mount section. 3. Lay mount on back. (See Figure 11) 4. Locate three tension adjustment screws. (See Figure 11) 5.
MSS6000 Installation Instructions Option B Option B uses the cable access at the center of the MSS-6000 and then routes the cables across the mounting surface and out the rear cable access slot in the back of the mount. (See Figure 14) Cable Access Rear Cable Access Slot Figure 14 Option C Option C uses the cable access at the center of the MSS6000 and then routes the cables down through an access hole or slot in the mounting surface.
Installation Instructions MSS6000 11
MSS6000 Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-000057 RevC 2009 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 05/09 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.