I N STA L L AT I ON I N S T R UC T I O N S Ceiling Tile Storage Kits CMS491/492 Series
CMS491/492 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions CMS491/492 DIMENSIONS CMS491 A 1.38 34.9 DOOR DROP 1.13 28.6 TILE INSERTION SPACE 0-0.25 6.4 SIDE TRIM EXTENSION (MIN-MAX) DEPTH ADJUST 19.25 489.0 TILE WIDTH B B 12.97 329.5 8.67 220.1 ELECTRICAL INSTALL PLATE SPACE FOR 1. A SINGLE GANG OUTLET 2. DUAL GANG OUTLET 3. PASS THROUGH FOR DUAL GANG OUTLET ATTACHED TO 1/2" CONDUIT 1 REMOVABLE SHELF INCLUDED 2 SPACES TOTAL AVAILABLE 23.67 601.1 MOUNTING WIDTH 2.25 57.2 BOTTOM SHELF SPACE 7.58 192.
Installation Instructions CMS491/492 DIMENSIONS CMS492 A 0.25 6.4 TILE INSERTION SPACE 19.25 489.0 TILE WIDTH B B 23.69 601.7 MOUNTING LENGTH 24.97 634.3 ELECTRICAL INSTALL PLATE SPACE FOR 1. A SINGLE GANG OUTLET 2. DUAL GANG OUTLET 3. PASS THROUGH FOR DUAL GANG OUTLET ATTACHED TO 1/2" CONDUIT 8.67 220.1 1 REMOVABLE SHELF INCLUDED 2 SPACES TOTAL AVAILABLE 23.67 601.1 MOUNTING WIDTH 7.60 192.9 AVAILABLE STORAGE HEIGHT SECTION B-B 0.88 22.2 TRADE CONDUIT SIZE 1/2" METRIC CONDUIT SIZE 16mm 2.
Installation Instructions CMS491/492 LEGEND + Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro B
Installation Instructions CMS491/492 optional TOOLS REQUIRED FOR INSTALLATION 1/4” 5/32” #2 Flathead 1 2 3 4 5 #2 Phillips PARTS INCLUDED NOTE: Some items may vary depending on specific model number.
Installation Instructions CMS491/492 SUPPORT CABLE INSTALLATION PREPARING FOR INSTALLATION Installation Requirements The CMS491/492 has been designed to be mounted recessed into a suspended ceiling consisting of 2’ x 2’ ceiling tiles and secured by a Wire Vice system.
Installation Instructions CMS491/492 Wood Ceiling Structure Installing Electrical Box and Outlets WARNING: Anchors must be installed into wood with a Determine desired location for installing electrical outlets within box. minimum thickness of 1-1/2" (38.1 mm) or greater. Box sidewall install option Figure 6 1 Drill 5/32" diameter x 2" deep hole at each marked cable anchor support location (See Figure 4). Remove debris from hole.
Installation Instructions CMS491/492 Projector Mount Plate Electrical Install Option 1 Remove attached electrical plate from underside of projector mount plate. Save nuts for reinstall. Cleat adjustment for various tile heights 1 Loosen screws along side cleat, adjust and retighten as needed to accommodate for tile height. 2 Remove break away panel from projector mount plate. CAUTION: Avoid sharp edges.
Installation Instructions CMS491/492 Installing Cable to Box Frame 5 Secure CMS491/492 assembly in place by feeding 1 Remove adjacent ceiling tiles as needed to access cable attachment locations. Figure 16 #10-24 x 5/8 pan head tapping screws (G) through holes as shown and tighten until secure against ceiling tile framing (2 screws each on opposite sides of the assembly).
Installation Instructions CMS491/492 Finish Install Site 1 Pre-cut a ceiling tile to fit inside the drop panel framework Projector Mount Plate and Extension Column Installation NOTE: The following instructions refer to installing Models SIZE: CMS491: 19 1/8” x 10 3/8” CMS492: 19 1/8” x 22 1/8” CMS491C and CMS492C, or installing the Listed accessories CMS441 and CMS442 into Models CMS491 and CMS492, respectively.
Installation Instructions CMS491/492 4 Secure extension column by one of the following methods (See Figure 25): A. Install one 10-24 x 1/4" Phillips pan head screw (D) into extension column support, tightening firmly against column. B. OPTIONAL: Install one 10-24 x 1/4" button head security screw (E) through security spinner (F) into column support, tightening firmly against column. NOTE: Security spinner (F) is designed to spin, even when screw is tight.
CMS491/492 Installation Instructions 13
Installation Instructions 14 CMS491/492
CMS491/492 Installation Instructions 15
Installation Instructions CMS491/492 USA/International Europe Chief, a products division of Milestone AV Technologies 8800-002680 Rev00 2014 Milestone AV Technologies www.chiefmfg.com 11/14 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.