INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação K1D100 Istruzioni di installazione Installatie-instructies Instructions d´installation K1W100 K1C100 K1W200 K1D200 K1C200 K1P100 K1P200 Height-adjustable Monitor Arm Series Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K1 Series
K1 Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions K1 Series DIMENSIONS K1D100 3.94 100 EXTENSION MIN 2.09 [53.14] MAX 19.9 [505.5] 2.95 75 90 INTERFACE ROTATION CABLE MANAGEMENT COVER QUICK RELEASE VESA INTERFACE PITCH RANGE 10 DOWN 75 UP PITCH TENSION ADJUSTMENT 14.70±6.5 CABLE MANAGEMENT COVER DESKTOP THICKNESS RANGE .75 19.05 MAX 2.50 [63.5] 4.66 118.3 K1D200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92 " [887] 411.2 16.19 EXTENSION MIN 2.09 [53.2] MAX 19.9 [505] 3.937 2.
K1 Series Installation Instructions DIMENSIONS (CONTINUED) K1W100 188.1 7.41 100 3.94 QUICK RELEASE VESA INTERFACE EXTENSION MIN 2.09 [53.2] MAX 19.9 [505] 75 2.95 90 INTERFACE ROTATION PITCH RANGE 10 DOWN 75 UP CABLE MANAGEMENT COVER PITCH TENSION ADJUSTMENT 284.9 11.22 HEIGHT ADJUSTMENT 399±165.1 15.71±6.5 CABLE MANAGEMENT COVER 399 15.71 61.6 2.43 140 5.51 81.7 3.22 K1W200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92 " [887] 411.2 16.19 3.937 2.
Installation Instructions K1 Series DIMENSIONS (CONTINUED) K1C100 7.41 LOWER PROFILE INSTALL 90 INTERFACE ROTATION 100 3.94 75 2.95 QUICK RELEASE VESA INTERFACE CABLE MANAGEMENT COVER 13" LIFT ARM HEIGHT ADJUSTMENT PITCH RANGE 10 DOWN 75 UP PITCH TENSION ADJUSTMENT TOTAL HEIGHT ADJUSTMENT LOWER PROFILE 32.86 [834.6] CABLE MANAGEMENT COVER HEIGHT ADJUSTMENT KNOB K1C200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 36.5" [927.1] 449.3 17.69 3.937 90 INTERFACE ROTATION 2.
K1 Series Installation Instructions DIMENSIONS (CONTINUED) K1P100 POLE CLAMP RANGE 1.50" - 1.90" [38.1 - 50.8] 188.1 7.41 2.297 (MAX 19.12) QUICK RELEASE VESA INTERFACE 100 3.94 75 2.95 90 INTERFACE ROTATION PITCH RANGE 10 DOWN 75 UP CABLE MANGEMENT COVER PITCH TENSION ADJUSTMENT 13.60±6.50 HEIGHT ADJUSTMENT CABLE MANGEMENT COVER 2.50 K1P200 POLE CLAMP RANGE 1.50 [38.1] - 1.90 [48.26] MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92" [887] 2.172 (MAX 19.00") 411.2 16.19 3.937 2.
Installation Instructions K1 Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevest
K1 Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 3/16" (included) 1/8" (included) 5/32" (included with K1P Series only) PARTS A (1) [monitor arm] (K1D100 shown) B (4 or 8)* M4x14mm C (4 or 8)* M4x25mm D (4 or 8)* M10x5.
Installation Instructions K1 Series Assembly And Installation Low Profile Installation (K1C Series Only) Connecting K1C Series (column mount) to Desk Standard Installation 1. Remove top cap from column. (See Figure 3) 2. Slide mount assembly off of column. (See Figure 3) 1. Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting.(See Figure 1) NOTE: If space is limited behind desk (i.e. against wall, etc.
K1 Series Installation Instructions Connecting K1D Series (desk mount) to Desk Connecting K1W Series (wall mount) to Wall 1. 1. Determine mounting location on wall. 2. Use a stud finder to locate 2" x 4" wood stud. 3. Use wall bracket to mark and drill two 3/16 x 2 1/2" holes in wall at desired mounting location. (See Figure 6) 4. Use two 1/4-2 1/2" hex head lag screws (F) and two 1/4" washers (G) to install wall bracket onto wall.
Installation Instructions K1 Series Connecting K1P Series to Pole 1. Determine approximate location for mount keeping in mind display size, extension, height adjustment requirements. 2. Place mount (A) against pole with clamp (H) on opposite side of pole. (See Figure 7) 3 (J or K) x 4 WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! See Display Removal section for details. 2.
K1 Series Installation Instructions Adjustments (for recessed mounting holes) quick release faceplate Head Tilt Adjustment 3 (C) x 4 1. Adjust head tilt to desired tilt position. (See Figure 12) 2. Adjust head tilt tension screw to change the adjustment tension. (See Figure 12) Height Adjustment 1. Adjust height to desired level. (See Figure 12) 2. Open cable management cover on upper arm to expose height-adjustable tension screw. See Cable Management section for details. 3.
Installation Instructions K1 Series Pivot Adjustment Range Single Arm Models (K1D100, K1C100, K1W100 and K1P100) 1. Adjust arm angle as desired up to 90 degrees in either direction.
K1 Series Installation Instructions Portrait Adjustment 1. The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor. (See Figure 16) 3 2 cable (typical) 4 3 2 4 Figure 18 3. Figure 16 Route cables through cable management channels. (See Figure 18) IMPORTANT ! : Be sure to leave enough slack in the cables near display and arm joint to allow for full arm articulation! WARNING: Only remove display from mount when the 4.
Installation Instructions K1 Series Display Removal WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 19) 1. Make sure display is in the upright position. 2. Remove quick release faceplate from mount by pressing quick release tab and sliding faceplate off mount.
K1 Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002059 Rev 02 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 09/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.
