INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação K1D100 Istruzioni di installazione Installatie-instructies Instructions d´installation K1W100 K1C100 K1W200 K1D200 K1C200 K1P100 K1P200 Height-adjustable Monitor Arm Series Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K1 Series
K1 Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions K1 Series DIMENSIONS K1D100 3.94 100 EXTENSION MIN 2.09 [53.14] MAX 19.9 [505.5] 2.95 75 90 INTERFACE ROTATION CABLE MANAGEMENT COVER PITCH RANGE 10 DOWN 75 UP QUICK RELEASE VESA INTERFACE PITCH TENSION ADJUSTMENT 14.70±6.5 CABLE MANAGEMENT COVER DESKTOP THICKNESS RANGE .75 19.05 MAX 2.50 [63.5] 4.66 118.3 K1D200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92" [887] 411.2 16.19 EXTENSION MIN 2.09 [53.2] MAX 19.9 [505] 3.937 2.
K1 Series Installation Instructions DIMENSIONS (CONTINUED) K1W100 188.1 7.41 100 3.94 QUICK RELEASE VESA INTERFACE EXTENSION MIN 2.09 [53.2] MAX 19.9 [505] 75 2.95 90 INTERFACE ROTATION PITCH RANGE 10 DOWN 75 UP CABLE MANAGEMENT COVER PITCH TENSION ADJUSTMENT 284.9 11.22 HEIGHT ADJUSTMENT 399±165.1 15.71±6.5 CABLE MANAGEMENT COVER 399 15.71 61.6 2.43 140 5.51 81.7 3.22 K1W200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92 " [887] 411.2 16.19 3.937 2.
Installation Instructions K1 Series DIMENSIONS (CONTINUED) K1C100 7.41 LOWER PROFILE INSTALL 90 INTERFACE ROTATION 100 3.94 75 2.95 QUICK RELEASE VESA INTERFACE CABLE MANAGEMENT COVER 13" LIFT ARM HEIGHT ADJUSTMENT PITCH RANGE 10 DOWN 75 UP PITCH TENSION ADJUSTMENT TOTAL HEIGHT ADJUSTMENT LOWER PROFILE 32.86 [834.6] CABLE MANAGEMENT COVER HEIGHT ADJUSTMENT KNOB K1C200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 36.5" [927.1] 449.3 17.69 3.937 90 INTERFACE ROTATION 2.
K1 Series Installation Instructions DIMENSIONS (CONTINUED) K1P100 POLE CLAMP RANGE 1.50" - 1.90" [38.1 - 50.8] 188.1 7.41 2.297 (MAX 19.12) QUICK RELEASE VESA INTERFACE 100 3.94 75 2.95 90 INTERFACE ROTATION PITCH RANGE 10 DOWN 75 UP CABLE MANGEMENT COVER PITCH TENSION ADJUSTMENT 13.60±6.50 HEIGHT ADJUSTMENT CABLE MANGEMENT COVER 2.50 K1P200 POLE CLAMP RANGE 1.50 [38.1] - 1.90 [48.26] MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92" [887] 2.172 (MAX 19.00") 411.2 16.19 3.937 2.
Installation Instructions K1 Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevest
K1 Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 3/16" (included) 1/8" (included) 5/32" (included with K1P Series only) PARTS A (1) [monitor arm] (K1D100 shown) B (4 or 8)* M4x14mm C (4 or 8)* M4x25mm D (4 or 8)* M10x5.
Installation Instructions K1 Series Assembly And Installation Low Profile Installation (K1C Series Only) Connecting K1C Series (column mount) to Desk Standard Installation 1. Remove top cap from column. (See Figure 3) 2. Slide mount assembly off of column. (See Figure 3) 1. Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting.(See Figure 1) NOTE: If space is limited behind desk (i.e. against wall, etc.
K1 Series Installation Instructions Connecting K1D Series (desk mount) to Desk 1. 1. Remove desk clamp from mount by loosening button head cap screw until clamp is completely disengaged from the bolt. (See Figure 7) 2. Manuever clamp so that it is totally removed from desk mount. (See Figure 7) Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting. (See Figure 5) NOTE: If space is limited behind desk (i.e. against wall, etc.
Installation Instructions K1 Series 3 6 set screw 5 side view 4 (F) x 2 (E) (G) x 2 Figure 9 Connecting K1W Series (wall mount) to Wall 1. Determine mounting location on wall. 2. Use a stud finder to locate 2" x 4" wood stud. 3. Use wall bracket to mark and drill two 3/16 x 2 1/2" holes in wall at desired mounting location. (See Figure 9) 4. Use two 1/4-2 1/2" hex head lag screws (F) and two 1/4" washers (G) to install wall bracket onto wall.
K1 Series Installation Instructions Display Installation For recessed mounting hole installation: 1. • Remove quick release faceplate from mount by pressing quick release tab and sliding faceplate off mount. (See Figure 11) • 1 Place four spacers (D) on top of mounting holes on back of display. (See Figure 13) Using Phillips screwdriver, carefully install four M4x25mm screws (C) through corresponding holes on faceplate, spacers (D) and into the mounting mounting holes on the display.
Installation Instructions K1 Series Adjustments Pivot Adjustment Range Head Tilt Adjustment Single Arm Models (K1D100, K1C100, K1W100 and K1P100) 1. Adjust head tilt to desired tilt position. (See Figure 15) 2. Adjust head tilt tension screw to change the adjustment tension. (See Figure 15) 1. Height Adjustment Adjust arm angle as desired up to 90 degrees in either direction.
K1 Series Installation Instructions Portrait Adjustment 1. edge of desk or wall face (top view) 90 degrees range of motion per arm The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor. (See Figure 19) perpendicular centerline Figure 17 Column Height Adjustment (K1C Series only) 1. Loosen column adjustment knob. (See Figure 18) 2. Adjust height to desired level. (See Figure 18) 3. Tighten column adjustment knob.
Installation Instructions K1 Series Display Removal WARNING: Only remove display from mount when the 3 2 display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 22) cable (typical) 4 1. Make sure display is in the upright position. 2. Remove quick release faceplate from mount by pressing quick release tab and sliding faceplate off mount. (See Figure 22) 3 2 quick release tab 4 Figure 21 3.
K1 Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002059 Rev06 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 01/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.