INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation K1P110 K1P22H K1P120 K1P220 K1P Pole Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K1P Series
K1P Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions K1P Series DIMENSIONS K1P110 1.50" - 1.90" [38.1 - 50.8] 0.78 19.8 DYNAMIC LIFT ARM LENGTH RANGE STRAIGHT ARM = MAX FULL UP/DOWN = MIN 10.21 7.12 259.3 180.9 TILT RANGE 75 UP 10 DOWN DYNAMIC HEIGHT ADJUST RANGE 14.58 1.58 370.3 40.1 K1P22H INTERFACE ROTATION RANGE 90 MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 0.78 19.
K1P Series Installation Instructions K1P120 1.50" - 1.90" [38.1 - 50.8] 6.75 171.5 LENGTH RANGE STRAIGHT ARM = MAX FULL UP/DOWN = MIN TILT RANGE 75 UP 10 DOWN INTERFACE ROTATION RANGE 90 MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 DYNAMIC HEIGHT ADJUST RANGE 24.31 11.31 617.6 287.4 K1P220 1.50" - 1.90" [38.1 - 50.8] 0.81 20.
Installation Instructions K1P Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beves
K1P Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 3/16” (included) 1/8” (included) 5/32” (included) PARTS * - (single display models/dual display models) A (1) [Pole clamp arm] (K1P110 shown) B (4/8)* M4x14mm E (1) [pole clamp] C (4/8)* M4x25mm D (4/8)* M10x5.
Installation Instructions K1P Series Assembly And Installation Connecting to Pole 1. Determine approximate location for mount keeping in mind display size, extension, height adjustment requirements. 2. Place mount (A) against pole with clamp (E) on opposite side of pole. (See Figure 1) 2 (J3) (J8) x 2 (J9) (E) (J5) (J1) 1 (J10) (J11) 3 or (J4) (F or G) x 4 (J12) (A) Figure 1 3. Using 5/32” hex key (L) and appropriate length screws, loosely attach assembly to pole clamp (E).
K1P Series Installation Instructions For recessed mounting hole installation: • WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the K1P Series Monitor Arm up to (and including) the display does not exceed the weight limits listed below.
Installation Instructions K1P Series Handle Installation (K1P22 model only) 1. Loosen four screws securing handle brackets to K1P22 array. (See Figure 7) 2. Install uprights of handle (J2) into handle brackets located on the back of array. (See Figure 7) Adjustments Pitch Adjustment (non-array models) 1. Adjust pitch to desired tilt position. (See Figure 9) 2. Adjust pitch tension screw to change the adjustment tension. (See Figure 9) Pivot Adjustment (non-array models) x4 1 2 3.
K1P Series Installation Instructions Lift Arm Tension Adjustment Adjustments - K1P22H models only 1. 1. Loosen knobs securing faceplates to array. (See Figure 13) 2. Slide displays laterally on array to adjust lateral shift. (See Figure 13) 3. Adjust pitch and pivot position as desired. (See Figure 13) 4. Tighten knobs to secure faceplates in position. (See Figure 13) Use 3/16” hex key (L) to adjust lift arm tension adjustment screw.
Installation Instructions K1P Series Display Removal pivot point of the arm (top view) WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 15) 1. Make sure display is in the upright position. 2. Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount.
K1P Series Installation Instructions Cable Management Array Models 1. 1. Install array cable clips (J7) to back of array. (See Figure 20) 2. Route cables through array cable clips (J7) as desired. (See Figure 20) 3. Route cables through arm cable clips as desired. (See Figure 20) 2. Press insides of cable management covers at both ends to unhinge tabs on either end of cable management cover on upper arm.
Installation Instructions K1P Series 13
K1P Series 14 Installation Instructions
Installation Instructions K1P Series 15
K1P Series Installation Instructions USA/International Europe Chief, a products division of Milestone AV Technologies 8800-002479 Rev01 2014 Milestone AV Technologies www.chiefmfg.com 06/14 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.