Installation instructions

ManualsBrandsChief ManualsTVs & monitorsKontour

INSTALLATION INSTRUCTIONS

Instrucciones de instalación

Installationsanleitung

Instruções de Instalação

Istruzioni di installazione

Installatie-instructies

Instructions d´installation

K1 Series Dual Display Column Mount

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

K1C250

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation K1 Series Dual Display Column Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K1C250
PAGE 2
K1C250 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
PAGE 3
Installation Instructions K1C250 DIMENSIONS 3
PAGE 4
K1C250 Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beves
PAGE 5
Installation Instructions K1C250 TOOLS REQUIRED FOR INSTALLATION #2 3/16" (included) 1/8" (included) PARTS A (1) [K1C250 assembly] B (8) M4x14mm E (1) 3/16" C (8) M4x25mm D (8) M10x5.
PAGE 6
K1C250 Installation Instructions Assembly And Installation Display Installation Connecting K1C250 to Desk 1. 1. Remove quick connect faceplate from mount by pressing release tab and sliding faceplate off mount. (See Figure 3) Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting.(See Figure 1) NOTE: If space is limited behind desk (i.e. against wall, etc.
PAGE 7
Installation Instructions K1C250 For recessed mounting hole installation: Adjustments • Head Tilt Adjustment • Place four spacers (D) on top of mounting holes on back of display. (See Figure 5) Using Phillips screwdriver, carefully install four M4x25mm screws (C) through corresponding holes on faceplate, spacers (D) and into the mounting holes on the display. (See Figure 5) 1. Adjust head tilt to desired tilt position. (See Figure 7) 2.
PAGE 8
K1C250 Installation Instructions Pivot Adjustment Range Cable Management 1. 1. Use screwdriver to unhinge tab on either end of cable management cover on upper arm. (See Figure 10) 2. Slide screwdriver along edge of cover until remaining tabs are unhinged and cover is in the "open" position. (See Figure 10) and (See Figure 11) Adjust arm angles as desired within a 90 degree range from the edge and a perpendicular centerline of mount.
PAGE 9
Installation Instructions K1C250 Display Removal WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 12) 1. Make sure display is in the upright position. 2. Remove quick connect faceplate from mount by pressing release tab and sliding faceplate off mount.
PAGE 10
K1C250 10 Installation Instructions
PAGE 11
Installation Instructions K1C250 11
PAGE 12
K1C250 Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002131 Rev 01 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 12/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.