INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation LBM2X2U LBM3X1UP LBM3X2U LBM3X3U LBM2X2UP LBM3X2UP Bolt Down Video Wall Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description LBM Series
LBM Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions LBM Series WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair. WARNING: Do not use this product outdoors.
LBM Series Installation Instructions LBM3X2U MAX WEIGHT: 125 LBS PER DISPLAY 750 LBS TOTAL 108.89 2765.8 5.38 136.5 15.75 400.0 MAX MOUNTING PATTERN HEIGHT 88.27 64.38 2242.1 1635.1 SCREEN CENTER MAX HEIGHT 16.38 [416.1] SCREEN CENTER MIN HEIGHT 3.77 95.8 1.50 38.1 3.73 94.7 66.62 1692.0 2.53 64.1 65.88 1673.2 38.63 981.1 1.43 36.2 34.25 870.0 8.00 203.2 8.00 203.2 92.50 2349.5 17.38 441.3 LBM3X3U MAX WEIGHT: 100 LBS PER DISPLAY 900 LBS TOTAL 15.75 400.
Installation Instructions LBM3X1UP LBM Series MAX WEIGHT: 125 LBS PER DISPLAY 64.38 1635.1 SCREEN CENTER MAX HEIGHT 17.38 LBM2X2UP MAX WEIGHT: 100 LBS PER DISPLAY 82.38 SCREEN CENTER MAX HEIGHT 17.
LBM Series LBM3X2UP 82.38 2092.3 SCREEN CENTER MAX HEIGHT 17.
Installation Instructions LBM Series Bolt Down Dimensions LBM2X2U/LBM3X1UP LBM2X2UP/LBM3X2UP BOTTOM VIEW FOR BOLT DOWN INSTALLATION LARGER RADIUS FACES FRONT TO ATTACH TO COLUMN. COLUMN BOLT PATTERN NOT SQUARE 8.00 203.2 6.00 152.4 1.00 25.4 1.00 25.4 8.00 203.2 0.500 12.7 28.00 711.2 6.00 152.4 36.00 914.4 44.00 1117.6 LBM3X2U/LBM3X3U 8.00 203.2 BOTTOM VIEW FOR BOLT DOWN INSTALLATION LARGER RADIUS FACES FRONT TO ATTACH TO COLUMN. COLUMN BOLT PATTERN NOT SQUARE 8.00 203.2 6.00 152.4 1.
LBM Series Installation Instructions LEGEND 8 Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro B
Installation Instructions LBM Series TOOLS REQUIRED FOR INSTALLATION 1/2" (12.7mm) 3/8" (9.5mm) #2 3/16" (included with all) 1/8" (included with 3x2U,3x3U) 5/32" (included with 3x3U, 2x2UP, 3x2 UP) 3/8" (9.
LBM Series Installation Instructions Parts - Portrait Models - LBM3X1UP/LBM2X2UP/LBM3X2UP Hardware bag (letters correspond to letters on bag) *Quantities are listed as (LBM3X1UP/LBM2X2UP/LBM3X2UP) J (2/2/2) [bolt down plate] A (12/16/24) M6x12mm D (12/16/24) E (12/16/24) B (12/16/24) 1/4" .750x.344x.
Installation Instructions LBM Series Assembly And Installation 6. Place each bolt down plate (J) on top of drilled holes making sure holes on plate are aligned with drilled holes. (See Figure 3) Bolt Down Columns to Floor 1. Lay array columns (M) down on a flat surface. 7. 2. Use four 5/16-18 x 1 1/2" flat head cap screws (R) to connect each bolt down plate (J) to each columns (M).
LBM Series Installation Instructions Column Add-On Installation (LBM3X3U/ LBM2X2UP/LBM3X2UP only) 1. Insert one column add-on (V) to each column (M) making sure holes are lined up on each side. (See Figure 4) 2. Use 5/32" hex key (JJ) and six 1/4-20 x 1/2" flat head cap screws (W) to secure each column add-on (V) to each column (M). (See Figure 4) (rear view) 3 2 3 (AA) (FF) (rear view) center of top displays (V) 2 2 (W) x 6 (CC) x 2 Figure 5 1 3.
Installation Instructions LBM Series (AA) 5 7 8 (FF) 5 (BB) x 2 (K or L) (Q) display 4 height (CC) x 2 8 Figure 7 6. Use four 5/16-18 x 3/4" button head flange screws (BB) to secure each attached clamp bracket (P) to each quick connect base (Q). (See Figure 8) Figure 9 8. 6 (Q) (BB) x 4 Hang rails (K or L) into screws installed in previous step to quick connect bases (Q).
LBM Series Installation Instructions Add-On Rail Installation (LBM3X2U/LBM3X3U only) CAUTION: Using screws of improper diameter may 1. Install add-on rails (DD) to right column following instructions in Rails Installation section. 2. Use three #10-24 x 1 1/2" flat head cap screws (X) to attach each add-on rail (DD) to display rail (L). (See Figure 11) 2 damage your display! Proper screws will easily thread into display mounting holes. (X) x 3 2.
Installation Instructions (portrait models) LBM Series 5 (A-C or F-H) x 4 (D) x 4 (Y) (E) x 4, if necessary (Z) Figure 13 WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of each display and attached accessories mounted to the LBM mount does not exceed the limits listed below.
LBM Series Installation Instructions 6. Starting from the bottom and working up, hang interface brackets (Y and Z) to display rails (K or L). (See Figure 14) Adjustments 7. Use 1/4-20 x 1 1/4" socket head cap screws (I) to secure interface brackets (Y and Z) to rails for each display. Screws must engage through both holes to be fully secured. (See Figure 14) Height Adjustment NOTE: Display positions may need to be adjusted after height and/or plumb adjustments in order to maintain desired alignment.
Installation Instructions LBM Series Additional Cable Management Options 2. Cables may be routed through tops of columns and out through the back cable management hole. (See Figure 18) 2 (KK) 5 2 Figure 20 Figure 18 3. If rails needed to be installed on top of cable management holes, cables may be routed through quick connect bases (Q) prior to the rails being installed. (See Figure 19) 4.
LBM Series Installation Instructions FRONT Figure 21 18
Installation Instructions LBM Series 19
LBM Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002372 Rev00 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 03/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.