INSTALLATION INSTRUCTIONS LCM1UP (Shown installed to CPA Series extension column as example only) Single Portrait Flat Panel Ceiling Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description LCM1UP
LCM1UP Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions LCM1UP DIMENSIONS DIMENSIONS: INCHES [MILLIMETERS] 3
LCM1UP Installation Instructions LEGEND Tighten Fastener Adjust Apretar elemento de fijación Ajustar Befestigungsteil festziehen Einstellen Apertar fixador Ajustar Serrare il fissaggio Regolare Bevestiging vastdraaien Afstellen Serrez les fixations Ajuster Loosen Fastener Remove Aflojar elemento de fijación Quitar Befestigungsteil lösen Entfernen Desapertar fixador Remover Allentare il fissaggio Rimuovere Bevestiging losdraaien Verwijderen Desserrez les fixations Retirez Philli
Installation Instructions LCM1UP TOOLS REQUIRED FOR INSTALLATION 3/32" (included) 1/8" (included) 5/32" (included) M5 (included) #2 1/2" or 13mm PARTS [Interface Bracket Hardware Kit] A (8) M4x16mm E (6) M5x20mm I (6) M8x20mm B (6) M4x20mm F (6) M5x25mm C (6) M4x25mm G (6) M6x16mm M (8) L (8) .750x.323x.250 .750x.344x.
LCM1UP Installation Instructions INSTALLATION 4 WARNING: FAILURE TO PROVIDE ADEQUATE (X) x 2 STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.
Installation Instructions 5. LCM1UP Install and tighten two 5/16" x 3/4" set screws (X) through back of mount (CC) and against column. (See Figure 4) (L or M) (FF) 5 (X) x 2 (N) Figure 4 Attaching Interface Brackets to Display 1. Lower the latch mechanism on each interface bracket (FF).
LCM1UP Installation Instructions Attaching Display to Ceiling Mount 1. Ensure that the latch mechanisms on interface brackets (FF) are already lowered. (See Figure 5) 2. While supporting both sides of display, lower display onto ceiling mount, hooking top of interface brackets onto front of ceiling mount.
Installation Instructions LCM1UP OPTIONAL: Security Tilt The ceiling mounts allow -5° to 20° tilt. The ceiling mount can be locked at 0°, 5°, 10° and 15° tilt. 3. Loosen two tilt friction screws (located each side). (See Figure 10) 4. Adjust tilt as required. Note specific degrees of tilt. (See Figure 10) 5. Tighten two tilt adjustment screws if NOT using the 0°, 5°, 10° or 15° settings. 1.
LCM1UP 2. Installation Instructions Install back cover (DD) into four holes on back of ceiling mount. (See Figure 14) (DD) Figure 14 3. Install one side cover (EE) onto side of ceiling mount using two 10-24 x 1/2" flat head screws (W). (See Figure 15) 4. Repeat for other side of ceiling mount.
Installation Instructions LCM1UP 11
LCM1UP Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002403 Rev00 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 08/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
