INSTALLATION INSTRUCTIONS Single and Dual Display Floor Stands MF1, MF2, PF1, PF2 Series
MF1, MF2, PF1, PF2 Series Installation Instructions DISCLAIMER CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions MF1, MF2, PF1, PF2 Series DIMENSIONS MF1, MF2 [1463] 57-5/8 [1316] 51-7/8 [889] 35 [661] 26 [431] 17 [2327] 91-5/8 [2180] 85-7/8 [1211] 47-5/8 [39] 1-1/2 [65] 2-1/2 [44] 1-3/4 PF1, PF2 3
Installation Instructions MF1, MF2, PF1, PF2 Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticar
Installation Instructions MF1, MF2, PF1, PF2 Series TOOLS REQUIRED FOR INSTALLATION 1/4" (To remove base plates from packaging) 3/16" (included) PARTS A (1) (D) OR D (1) (PF Only) [(2) for Dual Display Models] F (1) (E) B (1) (Single Display Models Only) C [(2) for Single Display Models] [(4) for Dual Display Models] E (1) (MF Only) [(2) for Dual Display Models] (Front) G (4) H (1) 3/16" L (12) 5/16-18 x 1/2" M (4) 5/16-18 x 3/4" N (4) 5/16-18 x 1-1/2" J (1) 3/16" P (1) Q (4) K (1) 5/16"
MF1, MF2, PF1, PF2 Series Installation Instructions ASSEMBLY 2. Gather stand base pieces B and C (2) as shown in Figure 3 and push them together until the edges meet. (B) CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit and power drill to complete the attachment. Assembling Base for Single Display Stand 1.
Installation Instructions MF1, MF2, PF1, PF2 Series (PF1 Shown) (Back view of stand) (M) x 4 (D) or (E) (C) x 4 (F) Figure 5 3. Place top base section and center post assembly on top of the four base pieces. (See Figure 6) 4. Fasten lower base pieces to top base section and center post assembly using twelve 5/16-18 x 1/2" flat head cap screws (L). (See Figure 6) 4 Figure 7 Attaching Dual Head Assembly 1. Place head assembly (D) or (E) on the front of the stand assembly.
MF1, MF2, PF1, PF2 Series Installation Instructions Attaching Display to Stand WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY 5 MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to ensure the total amount of weight placed on the stand does not exceed 125 lbs (56.70 kg) for the MF1, 250 lbs (113.40 kg) for the MF2 [125 lbs (56.70 kg) per faceplate]; 200 lbs (90.72 kg) for the PF1, 400 lbs (181.44 kg) for the PF2 [200 lbs (90.72 kg) per faceplate].
Installation Instructions MF1, MF2, PF1, PF2 Series Tilting Display The display(s) can be tilted up to 15o either backward or forward from a straight upright position. In a dual stand, the tilting is only restricted by the size of the display. 1. (Front view of center post) 1 Turn knob counterclockwise on back of head assembly to loosen the tilt.
MF1, MF2, PF1, PF2 Series Installation Instructions Using the Stand 1 CAUTION: This stand is intended for use only with the products and maximum weights indicated: 125 lbs (56.70 kg) for the MF1, 250 lbs (113.40 kg) for the MF2 [125 lbs (56.70 kg) per faceplate]; 200 lbs (90.72 kg) for the PF1, 400 lbs (181.44 kg) for the PF2 [200 lbs (90.72 kg) per faceplate]. Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury.
Installation Instructions MF1, MF2, PF1, PF2 Series 11
MF1, MF2, PF1, PF2 Series Installation Instructions USA/International Europe Asia Pacific 8809-000039 Rev. C 2007 Chief Manufacturing www.chiefmfg.com 11/07 A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA.